How to make a trimmer Champion head. Selfmanufacture of bobbin

How to make out a trimmer Champion head

When finishing the garden, park zones and other places where you need to mow various types of plants, you often have to change the cutting tool in the trimmer. This is due to the fact that the standard cord installed in the head of the lawn mower can only work with grass. But when a shrub or a young sprout of a tree appears in the way of the worker, the trimmer line does not cope with this task and should be replaced by a more effective cutting tool.

Trimmer manufacturers have provided similar situations and complemented their products with a mass of nozzles in the form of knives with several “petals” or in the form of disks similar to disc saws.

If you replace the trimmer line with a knife with several “petals”, then this tool can mow both high grass and plants with thick and dry stems. And changing the trimmer line on the disk, the user gets the opportunity to cut bushes or small trees.

Knives and wheels are installed according to the following algorithm.

First, remove it by fixing the shaft, the mowing head (turn clockwise) or a nut with a shoe if the unit has not yet been used.
Set a saw or cutting knife so that they are placed on a small ledge (sleeve).

Install the fastener on the knife and screw the nut to the shaft (counterclockwise).
Tighten the nut (counterclockwise) using a pipe key.

You can watch this video to better understand the process of changing the tool.

Read how to remove a bearing from a grinder gearbox

How to remove the head of the trimmer: Basic rules

It is necessary to remove the trimmer head, adhering to the elementary rules in working with a motorcycle and an electric counterpart, and the main ones we will call:

Jam the gearbox for unscrewing the head with a special hexagon or neatly screwdriver, immersing it in a special hole. The latter can greatly clog with grass and merge with a common color, therefore. Delicately clean and find it;
It is necessary to jam so that the shaft does not turn;
Especially carefully work with the dismantling of a broken or cracked coil. Its elements can be everywhere;
Many users of a gas station today are looking for a Trimmer to remove the head on the network, and in instructive articles and videos we also FOCUS on different types of threads. Take into account the nuances of your tool;
For ease of work, it is practiced to turn the tool down down the engine, laying on a horizontal surface;
Shock and sharp efforts attached when removing the mowing head are inappropriate, since the plastic delicate case can be damaged;
Install a new coil or old, if it is still suitable, you need to be a cleaned tool.
The new tackle must meet the parameters of the old. Installation of another component, the characteristics of which do not meet the power of the braids, can adversely affect its elements and the operation of the mechanism as a whole;
We recommend working with a cleaned tool to avoid getting garbage and small particles of grass into the holes;
Blocking the gearbox by threading into the groove of the screwdriver is a mandatory procedure when installing a new coil or removing the old;
Remember the prevailing of the left thread on the gearbox of most trimmers;
Do not forget to remove the screwdriver from the groove groove at the end of the installation of the coil in place;
All fixations and removal must be carried out delicately, remembering that the coil is made of thin plastic;
It is not worth it to tighten the new coil (or the old one in its place), since after the working hours it will be impossible to remove it at the next time withdrawal. It is also not necessary to fix too easily. Weigh the load laid on this node during operation and the resistance of the cutting material;
If you need to determine the knife or spool instead of the coil to the trimmer. Analog cutting tackle, then the gearbox block is also carried out, twisting is carried out in the same circuit, but the installation itself is slightly different due to the specifics of each individual gear. Mount the knives on a trimmer with a coil if the tool is functionally working with different types of gear.

If you need to buy a trimmer line for a trimmer, then you can do this in the vastness of our site, but how to mount and replace it correctly. We will tell you joy in our articles.

Preliminary preparation

First in order to Win a trimmer line

, It is necessary to remove the spool (spool, spool) from the trimmer. Certain acts will depend on the difficulty of configuration and the type of product itself:

Small electronic trimmers with a working position of the motor and a reel from the bottom are usually side buttons on both sides of the coil. With simultaneous pressing, the highest part of the coil, coupled with the inner M, is turned off the coosile trimmer line, and the lower part remains turned on trimmer. It is advisable to analyze the bobbin on an even, even place, so that the spring enters the design, does not jump out and not be lost;
Electric and gasoline trimmers with a curved shaft without the possibility of installing a knife, as a rule, have coils with a special lamb: in such structures, hold the coil in one position with one hand and rotate the locking reel on the wing shaft counterclockwise. After disconnecting the nut, the entire drum is removed.
Electric and gasoline trimmers with the ability to install a knife on a straight rod (for example, Calm Trimmers) have a hole under the coil. A screwdriver or another suitable object is inserted into this hole so that the rod is motionless, and with slow rotation, this relative position is achieved when the screwdriver enters the hole and the coil is fixed. After that, the coil body is scrolled clockwise (left) and removed from the trimmer.

For the second and third cases, the coil, depending on the design, are versed in various ways. In lamb drums, the lamb is twisted, clamps are clamped in high coils, and one part of the coil is freed from the other. If the halves of the bobbin are connected by threads, then it is enough to turn them with your hand in opposite directions until they completely unscrew.

How to remove the coil and replace the trimmer line

The owners of the trimmers, mostly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or trimmer line in the reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.By.Step instructions given later.

Before filling the trimmer line into the coil, drown out the engine of motorcycles or de.Energize the electrimmer to avoid injuries that may occur when the cutting tool is randomly launched.
Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, the trimmer coil should be twisted to the right, that is, clockwise.
Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.Automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
Cut the required amount of trimmer line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the trimmer line, since this will lead to increased load on the engine and greater consumption of gasoline.
Find the middle of the segment of the cord, folding it in half. You will get a loop.
Special grooves are cut out inside the coil (there may be holes). Insert the loop from the trimmer line into this groove.
Wind the trimmer line on the coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the trimmer line about 20 cm long and fix them in the grooves located on the sides of the coil.
Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
Dress the lid and fix it with latches.
Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. It will be necessary to tighten the coil of the trimmer to the left (against h. Arrows).

Change of vein on trimmer

If, with a light blow, the trimmer coil button on the ground does not lengthen, then the prerequisites for this happen.

Option 1. It came out snacking, t.E. Squeezing the cord between the turns. This non.Bond usually occurs if the user wound the trimmer line on the coil unevenly, with crossing the turns, or wound it with the missing tension. In the latter case, when the mowing head is rotated at huge revolutions under the influence of centrifugal force, the cord begins to drag on, under the influence of which you intervaling fishing. To eliminate the task, you will have to disassemble the coil on the trimmer and rewind the cord correctly, in other words, even coils with good tension.

Option 2.7. Very short ends protrude from the head. The trimmer line may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). The centrifugal force is not enough for the trimmer line to stretch. Therefore, it is required to suspend the unit (drown out the engine as it is also called disconnect the electrimmer from the network) and pull the trimmer line manually, by pressing the button earlier.

Option 3. The trimmer line was soldered by the snitches. This leads to the coil stops and does not even spin when the button is pressed. In the main thing, this happens for several reasons: the bad quality of the cord, overheating of the coil during prolonged operation of the unit, a string of trimmer line on solid items.

At the beginning of the cord of the advantage of manufacturers, you will like more of low.Quality and fusible materials that do not hold mechanical and temperature loads. Therefore, preference should be given to “branded” fishing.
If you still got a trimmer line of unknown properties, and it is often soldered at the time of work, that is, an option to follow the example of certain users, who, after refueling the cord, moisten it or silicone grease (from the spray can), or mineral oil). This procedure greatly reduces the possibility of soldering a trimmer line with each other.
Also, the trimmer line can sleep if at one time of the mowing it hits a hard object (stone, fence, dry branch, etc.D.). At the end of this, it is a little stretched and draws back into the head with a high speed. The cord is heated from friction, and its turns are stuck together. The only thing that is done to eliminate this malfunction is to open the trimmer coil and rewind the trimmer line.

A mowing string head is one of the types of actuating mechanisms of a garden trimmer. It is intended for mowing grass and constructively represents a special coil (bobin) from which a cutting cord (string, trimmer line) sticks out in different directions). The string is a consumable material that is subject to replacement during operation. Based on the constructive and operational features of the trimmer, manufacturers equip their products with a wide variety of types of heads-from simple manual coils to complex automatic bones. The more difficult the device of this mechanism, the more likely its breakdown. What to do if the coil does not spin, the string is not served or broken, as well as with other malfunctions. In the material further.

Review for the trimmer head Champion C5074 HT21

A trimmer head is a typical consumable for modern motorized cos (electrios or benzo, does not matter). Sooner or later, any user of such garden technology will be required. I have been working with various types of braids for more than 10 years and therefore I chose the head based on my experience of their operation. The product from the Champion C5074 HT21 seemed to me quite solid and was acquired after checking compliance with the required parameters for my benzooca.

A two-cord semiautomatic head in a cardboard-plastic blister is supplied. He is strong and colorful.

On the back of the package, the manufacturer and importer are indicated, requirements for the permissible diameter of the cord (2-3 mm).

Detailed instructions for replacing it and a list of compatible cobblestones from other manufacturers are given.

The product is made of relatively strong and viscous shockproof plastic. Pretty fat. The glossy appearance is a little confusing (I had one glossy head from Ebonite and did not even serve the season. The case scattered in a collision with a sharp stone). Head diameter 117 mm, height 73 mm. This is more than the average parameters for such products. Weight in the equipment of the manufacturer is 0.28 kg (2.5 m of trimmer line with a diameter of 2.4 mm). On the working side of the head is the Auto.Oddachi button of the cord. Spring.Loaded medium, not tough. Quite rational adjustment for the economical consumption of trimmer line and comfortable work.

A hole for stealing the head on the shaft of the gearbox was made on the reverse side. Left thread M10 by 1.25. The depth of the hole for the shaft of the braids is large (therefore, in the list are dozens of compatible models of braids).

The release of the cord from the case is reinforced with metal embedded a non.Ferrous metal alloy with a smooth blockage. That’s right, they will not rust and spare/save trimmer line from cliffs. The guides of the cord are installed tightly and their replacement during wear is not provided for.

I know from experience that the main drawback of this type of case is the protruding elements of the lock locks. Good speeds of a strict obstacle (stone, reinforcement and similar) they simply fail. Sometimes not immediately, but even then the damaged head remains to live not for long. On my spit, my native heads are deprived of this drawback. The locks have hidden latches and does not protrude nothing around the perimeter. The survivability of such a solution is fundamentally higher, but inside are made worse and refuel them one torment.

The same head is thought out sensible and replacement/winding of the cord is much more comfortable. The case is easily disassembled. You need to remove the lid by pressing on the tongues of locks. Then remove/stretch the remains of the trimmer line from the guide holes and then the bobbin will gently push out of the body with the inner spring.

It is tightly installed in a plastic sleeve (glass) and does not spontaneously fall out when analyzing the head. The normal decision that saves nerves and time (on some models when removing the lid, the spring strives to shoot and look for it later. ). In the picture below, note that the case has double walls and is reinforced with stiffness ribs. A competent solution that extinguishes the energy of external strokes and takes a bobbin from jamming.

After refueling the bobbin with a new cord, its tails must be threaded into special grooves of the bobbin. And then the ends of the trimmer line are fixed and the wound the cord does not strive to unwind back, which allows you to calmly pass them into the brass holes of the case and insert the bastard into the body without fuss.

Made thoughtfully, re.Renewing the head is convenient. Here I will note another drawback. A small bobbin designed by the manufacturer for winding only 2.5 meters of the cord. On other types of heads I wrap 5-7 meters (here the thickness and profile of trimmer line also plays a role). But this is relatively, because the replacement of the cord is not troublesome.

As a result, the Champion C5074 HT21 head is good for everyone, except for an unsuccessful solution of the lock locks and a small reserve of the cord. The price for such a product is very humane and change the broken one for a new one is not costly. Who has the lawns are even and clean and there is no need to climb into the boulets/landfills, it will serve for a long time. After all, the general quality of the materials used and manufacturing is quite at the level of serious equipment.

Benzokosa device: engine

The power unit is in most cases (for domestic use) a two.Stroke internal combustion engine operating on the fuel mixture of oil and gasoline. The power of the motor offered today by the household motorcycle market lies in the range from 0.5-0.8 liters.S (horsepower) up to 2-2.5

An important characteristic of the engine in the device Benzokos is the volume of its cylinder. It is on this value that the productivity of mowing work will depend

The greater the volume of the engine, the higher the cutting speed and, accordingly, the faster you can dig up the given area. Typically, for standard mowing, the power unit is enough, the volume of the cylinder of which is approximately 30-40 cubic cm cm.

The start.Up system in the device can consist of a large number of elements (their number and functionality depends on the branded developments of each company producing the tool), but among them the main inclusion button (1), the starting cable (2), the carburetor damper (3), and Pump (4) fuel pumping (primer). There are 2 types of launching benzokos. With an unfinished engine and with warmed. In the first case, it is necessary to transfer the button to the Start position, the damper is “closed” to the position, pump fuel 3-5 times 3-5 times, after which you can stretch the starter’s cord, making sharp and quick hand movements until the engine earned. Then it is necessary to transfer the damper to the “open” position and you can proceed to work. Starting a hot engine does not require manipulations with a primer and a damper.

In the device, the engine is the main element that generates the energy necessary for the rotation of the working body.

The main malfunctions of the coil

Electrimmer users and benzocos are often faced with a problem associated with a semi.Automatic mowing head. Coil malfunctions can be as follows:

If, with a light blow, the trimmer coil button on the ground does not lengthen, then the reasons for this may be the following.

DIY How to Make Easy Bobbin Holder Storage. Keep Bobbins Tidy in your Sewing Room

Option 1. There was a snack, t.E. Squeezing the cord between turns. This problem usually appears if the user wound the trimmer line on the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the trimmer line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, even turns with good tension.

Option 3. The trimmer line was soldered inside the mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a trimmer line on solid items.

In the first case, the cord of third.Party manufacturers can be made of low.Quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
But, if you nevertheless acquired a trimmer line of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it with either silicone grease (from the spray can), or mineral oil. This procedure greatly reduces the likelihood of soldering a trimmer line among themselves.
Also, the trimmer line can sleep if during the mowing it hits a solid object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open the trimmer coil and rewind the trimmer line.

There are situations when the Trimmer user notices a very quick trimmer line consumption. At the same time, he never hit the ground with a button to lengthen the trimmer line. The reason that the trimmer line is spontaneously lengthened, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head.

We offer you to familiarize yourself with a greenhouse for seedlings (58 photos): a mini greenhouse for a summer residence, a portable guy with your own hands, a greenhouse and a microvo with your own hands

How to change a trimmer line on a lawn mower: detailed instructions

In one thousand nine hundred 70 one year, a South American businessman George Bollas invented a lawn mower, which used a line as a cutting knife. A lot of time has passed since that time, the drive has become stronger, the modern trimmer can simply destroy the bark, because the thought itself reincarnated in mowing around the obstacles, without damaging the mow itself itself

For careful circumcision around the obstacles, you can use the smallest head and simply change it from huge areas to delicate braids. But the cutting tool itself must be replaced at times

We will tell how to disassemble the head of the lawn mower (trimmer) and wind the latest trimmer line.

Sources:

https: // Domdetaley.Ru/kak-razobrat-tranuu-golovku-Champion/ https: // Sovetinet.Ru/baza-znanij/kak-snyat-golovku-s-Trimmera.HTML https: // Sovetinet.Ru/baza-znanij/kak-snyat-golovku-s-Trimmera.HTML https: // labequip.Ru/kak-razobrat-tranuu-golovku-Champion/ https: // Domdetaley.Ru/kak-razobrat-tranuu-golovku-Champion/ https: // Veloelektro.Ru/kak-razobrat-tranuyu-golovku-Champion.HTML https: // Domdetaley.Ru/kak-razobrat-tranuu-golovku-Champion/ https: // labequip.Ru/kak-razobrat-tranuu-golovku-Champion/ https: // 101benzopila.Ru/kak-razobrat-tranuu-golovku-Champion/

How to remove the Champion Champion head451

Quite often, the trimmer is operated in the distance from the places where you can purchase spare parts for a mowing head when it breaks down. In this case, instead of a broken mechanism, you can install a simple coil made in design made by yourself. To do this, you need a sheet of plywood (textolite, metal, etc.), eyes, screws or screws. The process includes several stages.

A disk is cut out of the plywood sheet, which corresponds to the failed spool with a diameter.
A hole is drilled in the center of the disk that matches the diameter with the trimmer shaft.
Small eyes are attached to the opposite sides of the disk, which will serve to refuel the trimmer line.
Through the eyes pass the trimmer line and fix it with ordinary screws or screws. The coil is ready for work.
Clutching the made bobbin between the two washers, it is attached to the shaft of the trimmer with a nut.

To replace the trimmer line on a home.Made bobin, you will have to release fixing screws, insert a new section of the string and tighten the fasteners again. It is not necessary to remove the coil from the trimmer shaft, however, it is necessary to exclude the possibility of spontaneous launch of the motor.

So, above was step.By.Step with the pictures described methods of repairing the string head. As you can see, the process is not complicated. And most of the breakdowns are directly related to the inaccurate refueling of the string and its unsatisfactory quality. You can clearly see all the stages of the process on the video.

We fill the trimmer line in Trimmer.

I want to devote today’s article to the sore theme of summer residents and gardeners of the entire post.Soviet space “How to refuel a trimmer line in a trimmer”. Not many trimmers manufacturers in their operating instructions answer this question. Therefore, it is hard for ordinary gardeners to figure out how to do it right.

I want to start with a brief description of the technical characteristics of trimmers.

So, trimmers are electric and gasoline. The cutting element of trimmers can have a trimmer line and a knife. The trimmer line is ordinary, four. Pyathedral and intertwined (in the form of pigtails). Knives are from 2, 3 and four lobed knife. Knives are also plastic and metal.

The system for feeding trimmer line from the trimmer is manual, semi.Automatic and automatic.

Developer engineers who create new models of trimmers clearly calculate the diameter (thickness) of the trimmer line and the number of knife blades, according to the power of the trimmers. Otherwise, the engine is overloaded, which as a result leads to its breakdown. And these are additional and significant costs.

Trimmers are presented on the market today:

Триммер CHAMPION T523-2. Первый запуск.

With one nozzle. Only Leskova. With two nozzles-Leskova and three-four-blade knife. With one nozzle-only a three-four-blade knife.

Our Kulibins have long learned to improve any mechanisms. So, for example, some gardeners make successful, in their opinion, replacement of trimmer line with a metal cable, or fishing trimmer line. But at the same time, they do not think about the safety of their loved ones, because as a cable with the power of a working trimmer can easily break out and not only injure the mower and others, but leave a cripple for life.

The use of fishing trimmer line can and gives the best effect, I have never tried personally than a trimmer line for a trimmer, but such work has a number of inconveniences: when in contact with solid objects, it is planted or may simply be endlessly pulled out of the reel.

So, what is called closer to the topic. I give an example of how to refuel a trimmer line in a trimmer (Trimmer Bosch Art 30). Everything is very simple. Started.

After you have chosen a trimmer line for refueling, you need to cut off the required amount of trimmer line, because, as the entire trimmer line in a skein is not wound into a coil.

Cut off and begin to wind up.

Remove the coil and a protective casing from the coil.

How to remove and put a reel on a lawn mower!

Removed. We fix one end of the trimmer line into the gap and gently and evenly wrap the trimmer line.

The amount of trimmer line should be so that the protective casing of the coil is closed and the trimmer line on the coil is slightly unwound.

The second end of the trimmer line is seated in the hole on the protective casing.

Головка HT31 часть 3

Next, take the coil and the protective cover of the coil. We sit the end of the trimmer line from the coil into a metal hole on the protective cover of the coil. Pull the trimmer line a little.

We put on all this on a trimmer. Turn the coil clockwise to click.

Fastened. Now we connect the trimmer to the network. Put a trimmer in the original position for work. We turn on the trimmer. Excess fish length will be cut off on the trim blade.

Such a coil for a trimmer is attached as well as a coil with an ordinary trimmer line.

Types of gearboxes and lubricants

The mechanisms of gearboxes by the type of transmission are divided into subsequent varieties:

The main elements of cylindrical devices. These are gear cylinders. Benzokos are very often equipped with modules of this type, worm types of gearboxes and others are installed on trimmers. Transfer to them is carried out at the expense of the current screw. Planetary types of transmissions are distinguished by coaxial placement of shafts, and conical. Crossing.

Gear gear can work perfectly only in this case if there are no mechanical damage to the unit. For the usual functioning of the device, conditions of ordinary temperature must be made. Even the smallest distortions or overheating can cause jamming of parts of the mechanism.

Ensuring the desired equipment care allows lubricants for reducers of trimmers, the types of which depend on their mixture:

For semi.Liquid lubricants, the presence of a colloidal system with M of various additives and additives is typical. Plastic lubricant is suitable for a screw.Shaped and gear gear, therefore it is a universal option. The initial state of rigid suspensions is plastic.

Lubrication of the gearbox benzokos is provided by special composition specifically for gearboxes. Most of the lubricants have the appearance of semi.Liquid systems. Carrying out the choice of the desired lubricant, it is required to take into account the temperature regime for which the mixture is intended.

Self.Manufacture of bobbin

Quite often, the trimmer is operated in the distance from the places where you can purchase spare parts for a mowing head when it breaks down. In this case, instead of a broken mechanism, you can install a simple coil made in design made by yourself. To do this, you need a sheet of plywood (textolite, metal, etc.), eyes, screws or screws. The process includes several stages.

A disk is cut out of the plywood sheet, which corresponds to the failed spool with a diameter.
A hole is drilled in the center of the disk that matches the diameter with the trimmer shaft.
Small eyes are attached to the opposite sides of the disk, which will serve to refuel the trimmer line.
Through the eyes pass the trimmer line and fix it with ordinary screws or screws. The coil is ready for work.
Clutching the made bobbin between the two washers, it is attached to the shaft of the trimmer with a nut.

So, above was step.By.Step with the pictures described methods of repairing the string head. As you can see, the process is not complicated. And most of the breakdowns are directly related to the inaccurate refueling of the string and its unsatisfactory quality. You can clearly see all the stages of the process on the video.

The main malfunctions of the coil

Electrimmer users and benzocos are often faced with a problem associated with a semi.Automatic mowing head. Coil malfunctions can be as follows:

If, with a light blow, the trimmer coil button on the ground does not lengthen, then the reasons for this may be the following.

Option 1. There was a snack, t.E. Squeezing the cord between turns. This problem usually appears if the user wound the trimmer line on the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the trimmer line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, even turns with good tension.

In the first case, the cord of third.Party manufacturers can be made of low.Quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
But, if you nevertheless acquired a trimmer line of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it with either silicone grease (from the spray can), or mineral oil. This procedure greatly reduces the likelihood of soldering a trimmer line among themselves.
Also, the trimmer line can sleep if during the mowing it hits a solid object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open the trimmer coil and rewind the trimmer line.

Launcher of the starter and gearbox

The gearbox conveys the rotational moment from the engine shaft to the cutting tool, its gears during operation should be absolutely clean and necessarily lubricated with special lubricant.

The starter is necessary to bring the trimmer to working condition, its diagnosis is to check the tension of the lace of the starter coil with the teeth of the coil, which are often destroyed at a sharp launch.

A non.Working starter in a benzocos is not subject to repair, it must be replaced with a working unit, as part of a mandatory inspection or a set of repair measures.

Separate attention and care require cutting elements that must always be cleaned of dirt and mowed grass after operation. Regular inspection and thorough preparation of the device for work will help to avoid an expensive and expensive repair time, always be confident in the performance of benzocy.

Self.Manufacture of bobbin

A disk is cut out of the plywood sheet, which corresponds to the failed spool with a diameter.
A hole is drilled in the center of the disk that matches the diameter with the trimmer shaft.
Small eyes are attached to the opposite sides of the disk, which will serve to refuel the trimmer line.
Through the eyes pass the trimmer line and fix it with ordinary screws or screws. The coil is ready for work.
Clutching the made bobbin between the two washers, it is attached to the shaft of the trimmer with a nut.

Sources:

https: // 101benzopila.Ru/kak-snat-golovku-traimmera-Champion.T451/ https: // vseopilah.Ru/trimmery/kak-razobrat-tramernuyu-golovku.Hempion-tlnru/ https: // vseopilah.RU/Trimmery/Kak-Razobrat-Trimmernuyu-Golovku-Chempion/ https: // hitech-online.Ru/Tehnika-Dlya-Sada/Trimmer/Remont-Golovki.HTML https: // Domdetaley.Ru/kak-snat-golovku-na-trammer-boosch/ https: // labequip.Ru/kak-snat-golovku-traimmera-Champion.T451/ https: // Domdetaley.Ru/kak-snat-golovku-traimmera-Champion.T451/

Grass Trimmer bobbin, champion, head, make, trimmer