How to Make a Trimmer Petrol Stihl Video Properly
Why does not start petrol trimmer? Reasons and their elimination
Lately gasoline trimmer acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized spit allows you to quickly put your personal plot in order. However, sometimes it happens that trimmer does not start on hot and even cold. In such situations, you have to independently determine the cause of the malfunction. Let’s find out what to do if the trimmer does not start. Causes, which most often lead to such troubles will be considered below.
Where to start troubleshooting if not start trimmer? In situations when the tool stalls immediately after start-up, it is worth inspecting the following units of the unit:
- fuel tank;
- spark plug;
- fuel and air filter;
- exhaust channel;
It is the breakdown of the above locations that most often leads to the fact that the trimmer does not start well. What to do when the fuel was definitely normal, there is a spark, but the gas trimmer does not start? Let’s look at how to eliminate such troubles.
Fuel mixture check
Let’s say you don’t start trimmer. In this case, the first step is to check whether there is enough fuel in the tank, and also to evaluate the quality of the fuel mixture. It is necessary to refuel the motorized unit with exclusively high-quality gasoline. It is recommended to use fuel whose brand is not lower than AI-95. Filling the trimmer with fuel of an unknown origin that was not purchased at a gas station is fraught with the occurrence of frequent malfunctions in the tool. This may cause a malfunction of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.
Why does not start petrol trimmer? Incorrect preparation of the fuel mixture, which consists of oil and gasoline, can also lead to this. Why the gas trimmer will not start. The reasons why the gas trimmer stopped starting can be different, therefore. The proportions in which these components are connected are indicated by the manufacturers in the trimmer instruction manual. It is extremely not recommended to prepare the fuel mixture in large volumes, that is, for the future. Indeed, with long-term savings, the loss of the defining properties of a substance occurs. Therefore, if the trimmer does not start, it is worth draining the old fuel and use a freshly prepared fuel mixture.
Does the gas trimmer not start? Reasons and solutions for the Elitech T750
In general, such a conversation should start with the fact that after buying a garden gasoline tool it would be better to first familiarize yourself with the instructions attached to it. Then many problems could have been avoided. But since this happened the gas trimmer does not start, then we must look for sources of inoperability. And in this article we will consider the main reasons why the trimmer does not start on the example of the Elitech T750 model, as well as tell general recommendations for the operation of such a tool.
Start with the banal! We will figure out how to properly start a gas trimmer. It may be that the reason lies precisely here.
First you need to bring the red toggle switch on the trimmer bar to position "I". This means turning on the power. Then you need to switch the fuel supply lever on the carburetor and use the fuel “suction” button (similar to a pipette, located on the carburetor). This is necessary to supply gasoline to the engine. Return the fuel supply lever to its original position. Finally, sharply pull the starter handle toward you. The trimmer should work. Try several times if the first time fails. If after such manipulations the situation has not changed and the gas trimmer does not start, then you should first examine it yourself before leading to the service center. There are two main reasons why a garden trimmer will not start:
- Violation of the power circuit.
- There is no fuel.
- Let’s start with the ignition problems. In most cases, it is caused by the need to change the spark plug in the engine. It is done like this:
- First of all, we must take care of security measures, make sure that the trimmer is turned off. We bring the above toggle switch to the "STOP" position.
- Then remove the rubber protection from the plug and the wiring terminal. Using a special candle key, we unscrew the spark plug and replace it.
- After that, we assemble the device and carry out the procedure for trimming the trimmer described above.
The second reason the garden tool doesn’t work is because the fuel has run out. On the Elinech T750, the fuel tank is located near the motor, but on most trimmers it is there. We unscrew the cap from the tank and fill it with gasoline (the most optimal option is the AI-92, it is inexpensive and does not clog the carburetor like the AI-76). Do not forget to add special engine oil to the tank, 50 grams per gas tank is enough, without it the motor will begin to “sneeze” and will quickly become worthless. After we close the tank with a cap, wipe the surface of the trimmer and our hands with a dry cloth. We also do the above manipulations to turn on the garden tool.
If the gas trimmer does not start as before, then it makes sense to return it for repair. And the reason for this decision is simple. if you do not have the appropriate skills, repairing the equipment is almost impossible.
In order for the tool to serve as long as possible and there are no such malfunctions, you should, first of all, familiarize yourself with the instruction manual for the trimmer. Pay special attention to the operating time of the engine at the trimmer. take a short break every 15 minutes of operation and, finally, properly care for the tool, wipe it after work, lubricate it with graphite grease. Observing such simple rules, you can significantly increase the life of the tool and it is quite possible that you do not have to look for reasons why the gas trimmer will not start.
30,294 total views, 13 views today
The trimmer does not start. Why?
A gas trimmer is a surprisingly useful thing, with the help of which you can tidy up not only a miniature lawn in the backyard of the house, but also mow a lawn of considerable size. But, like all things in this world, it tends to break. In this article we will try to figure out what to do when the trimmer refuses to work.
Gas trimmer fails to start
So what to do if the gas trimmer does not start or does not start at all? The most common cause of this failure is poor quality fuel. Remember that, for example, Stihl and Husqvarna trimmers are unlikely to start on fuels with a quality lower than AI-92. Do not save on fuel, because repair of parts of a cylinder. a piston group can make up one third of the total cost of the braid, and sometimes even half. Also, when preparing the fuel mixture, it is necessary to correctly observe the proportions of fuel and oil, which are always indicated in the instructions for the trimmer.
Video: How to Make a Trimmer Petrol Stihl Video Properly
What to do if high-quality fuel is poured into the gas tank, there is a spark, but the tool still refuses to start? It is necessary to check the condition of the candle. It is located in the center of the mower housing. It must be carefully unscrewed and make sure there is no plaque on it. If it is, then carefully clean the candle from soot and dry it.
If the lawn mowing does not start even after the methods proposed above, then you need to try to remove the air filter and start the device without it. If the trimmer still doesn’t work, thoroughly dust the old filter or buy a new one.
It also happens that the mower runs for a maximum of 5 minutes, and then stalls and does not start until it cools down. In this case, try to open the filler cap of the gas bottle neck. a suction sound should appear. Then screw the cover back on. If you do this manipulation during the time when the trimmer just began to stall, then the speed will recover, and you can continue to work. If the mower stalled before opening the cover, you just need to start it as it should according to the instructions.
Trimmer does not start after winter
How to be in this situation? Do not worry and panic. This is a very common problem that can be solved in literally 3-4 minutes. Firstly, if last year’s fuel was left in the gas tank, it must be drained. Gasoline loses its octave properties after 2 weeks of inactivity. Secondly, you need to start a lawn mow after prolonged stagnation in a slightly different way. First you need to open the damper and pump a little fuel mixture into the carburetor, then pull out the handle until you feel a little resistance. After that, you can start the trimmer.
Trimmer Starts and Stalls
If, when you try to start the trimmer, it starts up, but immediately stalls, then the air filter can again serve as the reason for this. It is necessary to remove it and check if it is clogged with dust. If this is true, then you need to thoroughly clean it or purchase a new one. Also, the problem may be a malfunction of the ignition coil. In this case, it is better to take the mower to a service center.
The authorized service center "Agrotechservice". comprehensive warranty and post-warranty maintenance of landscape gardening, communal, power and construction equipment of world manufacturers!
Doesn’t Start Trimmer Petrol Causes Fills Candle
Why not start trimmer petrol? Reasons and their elimination
Recently, a gas trimmer has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized spit allows you to quickly put your personal plot in order. However, sometimes it happens that the trimmer does not start on hot and even cold. Why the gas trimmer will not start. The reasons why the gas trimmer stopped starting can be different, therefore. In such situations, you have to independently determine the cause of the malfunction. Let’s find out what to do if the trimmer does not start. The reasons that most often lead to such troubles will be discussed below.
How to start troubleshooting if the trimmer does not start? In situations when the tool stalls immediately after start-up, it is worth inspecting the following units of the unit:
- fuel tank;
- spark plug;
- fuel and air filter;
- exhaust channel;
It is the breakdown of the above locations that most often leads to the fact that the trimmer does not start well. Let’s look at how to eliminate such troubles.
Fuel mixture check
Let’s say you don’t starts up trimmer. In this case, the first step is to check whether there is enough fuel in the tank, and also to evaluate the quality of the fuel mixture. It is necessary to refuel the motorized unit with exclusively high-quality gasoline. It is recommended to use fuel whose brand is not lower than AI-95. Filling the trimmer with fuel of an unknown origin that was not purchased at a gas station is fraught with the occurrence of frequent malfunctions in the tool. This may cause a malfunction of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.
Why not start trimmer petrol? Incorrect preparation of the fuel mixture, which consists of oil and gasoline, can also lead to this. The proportions in which these components are connected are indicated by the manufacturers in the trimmer instruction manual. It is extremely not recommended to prepare the fuel mixture in large volumes, that is, for the future. Does the gas trimmer not start? Reasons and solutions for the example of Elitech T750. Indeed, with long-term savings, the loss of the defining properties of a substance occurs. Therefore, if the trimmer does not start, it is worth draining the old fuel and use a freshly prepared fuel mixture.
Diagnosis of the suppository canal
What to do if the used fuel mixture is in perfect order, but still not start trimmer petrol? Causes Mechanism failures can be covered in excessive humidification of the suppository canal. To diagnose and fix the problem, do the following:
- Unscrew the candle. Wipe it thoroughly and then dry.
- Drain excess fuel in the chamber through the corresponding spark plug hole.
- Clean the old candle if there is soot on its surface. To cope with the task will allow the use of ordinary ladies’ nail files or needle files.
- When installing the element in place, set a gap of 1 mm. To check the parameter, just put any coin in the lumen.
- Reassemble the function block.
- Try to have a trimmer.
Drying the candle channel is recommended for at least half an hour. However, in no case should you resort to calcining its elements. After all, heating the spark plug can lead to its final damage. What to do if the function block has been serviced in accordance with the above recommendations, but the trimmer is not starts up, is there a spark? In this case, it is worth treating the threaded connection with gasoline. The latter does not need to be abundantly impregnated with fuel. It should only be slightly moistened. To resort to such actions should be to ensure ignition. After all, no matter how strong a spark is given by a candle, there will simply not be anything to ignite in a completely dry chamber.
gas trimmer. If the trimmer does not start, check the ducts, then turn out the candle Why a lawn mowing. Wet candle. Engine flooded.
How can you drown the engine on a lawn mowing, if you are inattentive. Garden gasoline trimmer is quite simple on why the trimmer does not start on. Just one awkward movement
The Chinese lawn mowing will not start. This is interesting.
Spare parts for Chinese lawn mowers Does not start Chinese lawn mowing.
Even if it doesn’t start trimmer, It is worth evaluating the quality of the contact between the high-voltage wire and the candle. In the absence of a spark (in the presence of a reliable connection between these elements), most likely, the problem is caused by a breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the site.
Another common reason that does not start the trimmer is the clogging in the filter area. To confirm the guess, it is enough to dismantle the indicated block and try to start the unit without it. If the trimmer engine starts, you will most likely have to replace the air filter or at least thoroughly purge the old one. In the presence of heavy pollution on a surface of the filtering element it is necessary to use a new grid. When resorting to such actions, one should not leave the suction pipe completely without a filter. Indeed, the rush in this case may lead to the need to repair the entire piston group of the engine unit.
Why doesn’t the trimmer (gasoline) start?
There are several reasons why the trimmer will not start. I will list the main ones:
- bad fuel. For each trimmer model, you need gasoline with a specific octane rating. Refer to the instruction manual and make sure that you fill in the required one.
- filled candles. At the same time, I advise you to check the candles for performance. Sometimes even new (in the box) candles can be inoperative or defective.
- the fuel mixture does not enter the carburetor. Pump her up a bit.
- ignition coil out of order.
- muffler clogged. It is necessary to free him from soot. To do this, carefully disassemble and clean (you can burn it on a gas burner).
Reasons why gas trimmer does not start, maybe a few.
If the trimmer does not start or immediately stalls after start-up, then the problem may be in the fuel tank (namely, in the quality of the fuel), in the candle and in the holy channel, in the air or fuel filter, in the breather or the exhaust channel.
1). Before you start the trimmer, it is necessary to check the presence, and most importantly, the quality of the fuel mixture.
2). The trimmer may not start or stall when the candle is flooded. It will need to be unscrewed and wiped.
Dry the candle channel at least 30-40 minutes. Otherwise, a new candle may also be filled.
3). If the trimmer starts without an air filter, then it is better to replace the old filter with a new one.
4). The trimmer may not start if the fuel filter is dirty.
5). The trimmer may also start due to contamination of the breather.
Also, the cause may be dirt getting into the exhaust channel or clogging of the silencer mesh.
A gas trimmer is one of the most convenient and necessary things if you have a site. The gas trimmer itself is, in other words, a regular lawn mower, but very compact.
The reasons that the gas trimmer begins to stall are a few. We will analyze the most common:
- low-quality fuel. For some reason, many people believe that in lawn mowers (chainsaws, etc.) you can pour some stale fuel and nothing will happen. But, this is not so. A poor mix can just kill the trimmer. Let’s skip what exactly can break poor-quality fuel, since there can be many options and only full diagnostics will help. Take the simplest but most common option. a filled candle. If the reason is in it, then you can remove, wipe and dry.
- long storage. Trimmers are moody. They can, if they lay for a long time, stall at the factory. Then we do this