How to mow a trimmer without fishing line. Preparation of a trimmer for work

Homemade fishing line for trimmer

Many users of mowers, both electric and gasoline engines, some time after using the purchased trimmer line are asked: and how to replace it? If you exclude dangerous options (chain from a chainsaw, canvas from a hacksaw, wire, cable, string, etc.D.), which can cause severe injuries to the user and others, then a home.Made fishing line from a plastic bottle is considered the best way out of the situation.

Before proceeding with the manufacture of a home.Made cord, you will need to prepare the material itself, namely the plastic tape of the required width and length. To dissolve the PET bottle on the tape, use various devices, the manufacturing algorithm of which can be found on the Internet. If you are going to mow large areas overgrown with grass, and you will need a lot of home.Made cord, then, of course, it makes sense to make a more complex bottlecock from a corner or P-shaped aluminum profile. The process of manufacturing a bottle.Cutter is shown in this video.

But if you are not interested in the mass production of a plastic tape, then from time to time to dissolve the bottle on the strips in a simple way.

  • Take the usual PET PET PET.
  • Cut it in half (but not to the end).
  • Remove all the sides located inside the cork.
  • Folding the cut cork in half, pierce it with a knife through the figure below, while observing caution, since the plastic is very hard. To facilitate the process, the tip of the knife can be pumped up.
  • Cut the bottom of a plastic bottle with scissors (if possible exactly, without zazubin). Insert the bottle into the device from the side where the knife blade is sharpened, and begin to crash a little. When a small strip appears. Just start pulling it.

Thus, the entire plastic container will blossom into the tape of the same width.

A version of a bottle.Cutter, which you will always have at hand, can be made from the usual Charns for pencils, preferably made of aluminum. In detail how to make it, shown in this video.

Types of section

There are a lot of views of the trimmer line, you can not pay attention to the color of attention-as such general standards “color-characteristics” do not. An important factor is the type of cross section of the string, it is chosen depending on the type of grass.

  • Circle. Universal trimmer line. Smooth when mowing is characterized by an increased noise level, twisted, on the contrary, mows quieter, but is consumed faster (like any type of twisted fishing line).
  • Square or polygon. Such a trimmer line is more effective than round. Sharp corners cut the stems faster and better.
  • Asterisk, ribbed or twisted square. Has maximum efficiency and haircut speed.
trimmer, fishing, line, work

Неубиваемая косильная головка! Модернизация струнной катушки. Головка для триммера дешево и сердито!

Trimmers with an electric motor

Most of the electric models are sold in disassembled form, you need to assemble the tool yourself. Before you start working with an electric trimmer, make sure that its assembly is correct. This will protect you from injuries, and the tool. From breakdowns.

Check the battery charge level if the model eats from the battery, or connection to the network. Lubricate the gear with solidol or oil. For safety reasons, do not use the electrimmer in rain weather, do not mow wet grass them. Moisture falling under the device case can lead to a short.Circuit, a tool breakdown, as well as injuries to the operator.

See also  Doesn't Develop Turnover Patriot 555 Trimmer

What can be used instead of trimmer line

Many users of trimmers are wondering: how to replace the cord, by default used in this kind of devices? Unfluence experiments begin to carry out, installing metal or copper wire, metal cables or strings in a mowing head, as well as a regular fishing trimmer line.

If installed instead of fishing line Metal cable, then the trimmer turns into a dangerous device not only for the user, but also for others. This fact is explained by the fact that during the operation of the unit, the steel cable will be gradually shut up, its ends are gradually released, and small pieces of wire will fly in different directions at high speed.

And if you accidentally hook your or someone’s leg, working as an unit with a steel cable (wire), then a strong and deep section of the fabrics, and in some cases, amputation of the fingers are provided with you. The manufacturer is not in vain for these purposes, nylon uses, since it is quite light and durable, and when separating he does not fly away and cannot cause injury.

Use Fishing trimmer line In trimmer, instead of the standard, of course, it is possible, but this will add unnecessary trouble, because it quickly wears out, breaks, mows slowly and does not fit for cutting hard grass. In addition, during the work, a lot of time is lost to replace the broken tool more than once.

In practice, the installation of a regular trimmer line is justified if the user is going to mow grass near the fence, especially if he is from a rabid grid. In this case, in order to protect the standard and sometimes expensive cord from wear, it changes to a fishing trimmer line that is not a pity. Usually, to change the cord to the fishing line, it must be selected the greatest thickness-2-3 mm.

How to properly change the trimmer line of the garden trimmer to a steel cable

Get one most read article by mail once a day. Join us on and

Garden Trimmer is an exceptionally useful thing in the household. Few people guess that this device can be significantly modified with your own hands. There are, for example, craftsmen who put on a trimmer instead of a familiar trimmer line cable. How to do this correctly and what will come of all this ultimately. We look together.

The trimmer with a weak motor is very often able to manage a dense lawn, which is already talking about an attempt to cut real weeds. This state of affairs will not please any owner and even upset the fact that the acquired device was absolutely useless on the farm. Having got into such a situation, you should not lose heart ahead of time, because you can conduct a simple modernization of the trimmer, which will significantly increase the efficiency of its work.

So, for modernization, nothing will be required, namely: a rubber sleeve, a trimmer, a set of standard tools and, of course, a steel cable up to 2 mm with thick veins. The installation of the cable begins with the disassembly of the trimmer coil. After that, you need to measure and cut the cable so that it does not fight while working about the trimmer itself. After that, the cable is extended by the pliers and is bend in the middle. This is done in such a way that the result is a small loop.

A rubber sleeve prepared in advance is inserted into the resulting loop. It should have a slightly larger inner diameter than the shaft of the trimmer.

Note: if there is no sleeve, in the most extreme case it can be replaced by wrapping the loop with electrical tape. However, it is worthwhile to understand that such a system will not work for a long time by faith and truth about the truth soon it will have to be repaired, again wrapping it with electrical tape. Otherwise, the trimmer can become dangerous!

See also  Trimmer Shaft Lubrication

Now you should squeeze the sleeve, drowning the loose cable back. For reliability, you can fix it with wire screed. After that, he refuel into the base of the head, the sleeve is planted on the shaft. When all this is done, it remains to close the lid.

What as a result: the trimmer equipped with a cable will confidently chop even dense herbs, weeds and branches of shrubs.

Video

How about even more severe modernization, here’s a story about how to change a trimmer line for a saw disk.

Handyman Tips & Hacks That Work Extremely Well ▶3

How to properly change the trimmer line of the garden trimmer to a steel cable

Get one most read article by mail once a day. Join us on and

Garden Trimmer is an exceptionally useful thing in the household. Few people guess that this device can be significantly modified with your own hands. There are, for example, craftsmen who put on a trimmer instead of a familiar trimmer line cable. How to do this correctly and what will come of all this ultimately. We look together.

The trimmer with a weak motor is very often able to manage a dense lawn, which is already talking about an attempt to cut real weeds. This state of affairs will not please any owner and even upset the fact that the acquired device was absolutely useless on the farm. Having got into such a situation, you should not lose heart ahead of time, because you can conduct a simple modernization of the trimmer, which will significantly increase the efficiency of its work.

So, for modernization, nothing will be required, namely: a rubber sleeve, a trimmer, a set of standard tools and, of course, a steel cable up to 2 mm with thick veins. The installation of the cable begins with the disassembly of the trimmer coil. After that, you need to measure and cut the cable so that it does not fight while working about the trimmer itself. After that, the cable is extended by the pliers and is bend in the middle. This is done in such a way that the result is a small loop.

A rubber sleeve prepared in advance is inserted into the resulting loop. It should have a slightly larger inner diameter than the shaft of the trimmer.

Note: if there is no sleeve, in the most extreme case it can be replaced by wrapping the loop with electrical tape. However, it is worthwhile to understand that such a system will not work for a long time by faith and truth about the truth soon it will have to be repaired, again wrapping it with electrical tape. Otherwise, the trimmer can become dangerous!

Now you should squeeze the sleeve, drowning the loose cable back. For reliability, you can fix it with wire screed. After that, he refuel into the base of the head, the sleeve is planted on the shaft. When all this is done, it remains to close the lid.

What as a result: the trimmer equipped with a cable will confidently chop even dense herbs, weeds and branches of shrubs.

Video

How about even more severe modernization, here’s a story about how to change a trimmer line for a saw disk.

Types and use of knives for a trimmer

Disk knives, as a rule, are included in the set of delivery. If there are no cutting elements, you can buy them. To choose the optimal size of the products, measure the diameter of the landing hole and external diameter. Consumable elements of trademarks Shtil and Khuskvarn are interchangeable. Disk knives are classified according to the following parameters:

Discs are installed on gasoline trimmers with high power rates. With their help, you can mow dry shoots, weeds, shrubs and young shoots. It is not recommended to mow young grass with disc knives, since sticking grass is observed on the surface of the protective casing.

A tool equipped with perforated cutting discs is gaining momentum faster, effectively cuts vegetation. The disadvantages of disk elements include a high inertial moment, which leads to an increase in the starting power of the drive. In some cases, this leads to overload and overheating of the motor, and this negatively affects the functioning of the trimmer, reduces its working resource.

See also  How to Set Fuel Delivery on Champion Trimmer

Trammer trimmer line: why a lot is consumed

The cause of the large consumption is not only the wrong selection of the string. Problems with a mowing head, improper operation of motorcycles can also lead to increased trimmer line consumption.

Problems with a mowing head

First of all, it is worth calling negligence. The springs are often lost. Inexperienced mowers collect the head and do not install the spring. As a result, the trimmer line under the influence of centrifugal force during rotation is constantly slightly advanced. The string is cut off with a knife installed on a protective casing. As a result, an unreasonable increase in consumption, sometimes significant. A similar situation arises in an automatic trimmer. If the spring weakened, the thread is extended, cut off with a knife. To check, remove the casing and turn on the trimmer. If the trimmer line is slowly but constantly extended from the holes, you need to find a spring or replace the head.

The string can be impudent if the holes in the body and the fishing line are worn on metal bushings are worn out. There is only one way out. Change the head. Preferably modern, from thick impact.Resistant plastic. And with a quick refueling without disassembling the head of the head.

Incorrect operation of the trimmer

Like any technique, the trimmer has its own restrictions on the operating mode. This is especially true for low.Power unprofessional models. The instructions precisely indicate the maximum duration of work and the duration of the break between the inclusion. If you do not follow the operating mode, then not only the engine, but also the head will overheat. To overheat and stick together and a trimmer line for a trimmer. With severe heating, even a branded vein is supplied. Even tips do not help lubricate the cord with mineral oil or spray silicone grease. This takes away time, efforts and means (silicone is not very cheap). Therefore, you need to observe the switching mode of the motokos and buy a quality trimmer line. It is especially important to turn off the tool in a timely heat or at strong load.

When working with an automatic head, the mower often resets engine speed. When the head is slowed down, the trimmer line is extended, trimmed on the knife. And as a result, it is quickly consumed. The vein is also advanced when the head with the ground collides. The coil is unlocked, the fishing line is served. Over, in a collision with obstacles, the trimmer also goes down and often hits the head on the ground. You need to be careful when working on the slopes.

Problems of the organization of work

Before you start mowing, you need to inspect the front of the work. On the appearance of stones, small hemp and other obstacles. Even on a well-known lawn, something can appear. Stones fall even from the sky, cans and sticks can fly due to the fence. As a result, when meeting with obstacles, the fishing line for the trimmer is broken off. Therefore, you need to walk along the lawn and remove obstacles.

trimmer, fishing, line, work

The string is also cut off when meeting with a curb, wood, fence, shop, pipeline. You need to cut the grass very carefully near obstacles.