How to properly change the line on the trimmer

Installing a new line on the trimmer reel

Step two: winding the cutting material in sections

The next step is to wrap the line around the reel, being careful. It is necessary that each half is filled with its own winding, evenly, without intersections. Usually, arrows can be seen on the body of the winding reel, indicating the direction of winding. This point should be borne in mind when filling the spool with fishing line.

How to replace the trimmer line?

Replacing the trimmer line with step-by-step instructions will allow even an inexperienced lawn mower owner to perform a rather difficult job.

However, before starting work on changing the line on the trimmer, it is necessary to ensure the safety of the work. In particular, measures should be taken to prevent unintentional or unintentional starting of the mower:

• exclude spontaneous start,
• remove battery (if applicable),
• place the tool on a platform convenient for work.

It is convenient to work on changing the trimmer line when the mower is lying on the table, and the master who replaces the trimmer line has the ability to approach the tool from either side.

Step two: removing the winding drum (spool) with line

The next step in the process is the removal of the winding drum with line from the inside of the head. You need to turn the head open side to see the line and spool. On the side of the head, find two grooves (eyes) through which the fishing line is brought out.

It is necessary to free the line from the holes by turning the drum. then carefully remove the coil from the head area. The winding drum of some models is spring-mounted. This point must be taken into account when performing the extraction operation.

The procedure for removing the trimmer spool with line from the inside of the head: 1. head assembly with spool; 2. extraction carefully with a small axial rotation; 3. extracted parts

The old line is completely removed from the reel. To remove the old trimmer line, you need to remove the wood from the locking loops and pull the free end. This method removes all the old winding. The same process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Replacing the trimmer line: step-by-step instructions for replacing the trimmer line

Trimmers (they are also lawn mowers) are actively used by modern society for the care of lawns and other similar objects of horticultural farms. The tool is noted for its high efficiency, despite the questionable quality of cutting grass (compared to the usual peasant scythe. earth and sky). The main advantage of trimmers (lawn mowers) is high productivity with low expenditure of physical forces of the operator. However, over time, the trimmer’s cutting element (nylon scaffolding) wears out or gets damaged, making the trimmer a useless tool as a result. Hence, the task becomes urgent. how to replace the trimmer head and how to replace the trimmer head line? Let’s consider this process using the example of lawn mowers manufactured by “Black and Decker” and others.

Step three: complete the head assembly

Pull out the ends of the line through a pair of oval spool slots. Replace both washers and the spring (if any) with the supplied new parts. Bend both ends of the line at right angles.

The final technical touch of the process of changing the line on the trimmer is the imposition of the cap on the head, followed by fixation by pressing force and slight twisting.

How to replace string trimmer edger line

Pass each end into the hole at the base of the winding drum. Install the coil in the inner area of ​​the head, resting on the spring. Put on the cover, align with the base and lightly press downwards with a small counterclockwise rotation, place the cover on the tabs of the clips. This completes the replacement procedure.

removing the trimmer head cover

At the first stage of disassembly, the trimmer head cover is removed. In the example of Black and Decker trimmer models and others, to remove the cover, it is usually enough to apply some pressure to depress the locking latch that is located on the side of the head body.

On some models of lawn mowers, it is initially provided for the dismantling of the trimmer head, for which the hex key included in the tool kit is used. The head is usually held in place by two to three screws, which are accessed through the side holes of the rear decorative cover.

The head cover, where the line spool is installed, is usually held by a latch-tongue. It is enough to squeeze the latch tab with some effort and turn the lid slightly, after which the lid can be easily removed

At the moment of squeezing the locking tab, you need to slightly turn and lift the trimmer head cover to remove the winding drum.

How to wind the line onto the trimmer spool

At first glance, threading a line into the reel of a tool is not an easy task. But it is enough to carefully study this process. and in the future all the necessary actions will be performed without any difficulties.

It is worth reading this guide to find out how to tuck the line into the trimmer. The step-by-step instructions below take into account the peculiarities of the spools of different types of trimmers, therefore, it is applicable to any tool.

So, the procedure is as follows.

• The line spool is the bottom end of the trimmer. First of all, of course, you need to remove this head from the device. To do this, you need to fix the rod (or, in other words, the shaft) on which the coil is attached. It is required to fix it in such a way that it does not scroll. The easiest way to do this is by placing a kind of stupor (preferably metal) between the shaft threads through a special hole. When the shaft is fixed, the spool can be unscrewed.
• At this stage, you have to remove the bobbin from the head, on which the fishing line is attached. To do this, you need to disassemble the head into elements. To do this, you first need to find a retainer on its body. It is located on the circumference of the product and is like a button. When the latch is found, you need to press it firmly. Keeping the latch pressed, turn the head cover clockwise. Then you need to remove the cover and remove the bobbin.
• A tight spring is placed between the bobbin and the head. It needs to be put aside for a while so that it does not interfere with the winding process. Before proceeding with the step of winding the line, it is necessary to inspect the bobbin. If there are remnants of old fishing line on it, they must be removed. When the bobbin is cleaned, you can start preparing a new bobbin.
• From a previously prepared skein of new fishing line, it is necessary to measure and cut off six (maximum. seven) meters. Keep the bobbin close at hand.

At this point, the key stage actually begins, which this article is devoted to.

Thickness selection

In addition, you should pay special attention to the thickness of the consumable. For mowing young grass, a thread with a diameter of one and a half millimeters is suitable. The larger the diameter of the thread, the drier and coarser weeds it is capable of overpowering.

When choosing a fishing line by thickness, there is one “but”. It is important not only to assess the capabilities of the material, but also to take into account the features of the trimmer. Be sure to check the user manual that came with your tool for information on cutting element requirements.

Using the wrong thread can damage the tool. Using a thread that is too thick will overload the machine’s motor. And the use of a thread that is too thin will significantly increase the wear of the twisting mechanism.

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel it in the trimmer. When a suitable fishing line is found and purchased, you can begin to consider ways of winding it on a reel.

The first way to wind the line

The required amount of line has been cut off. Now you need to carefully examine the bobbin in order to understand what type it belongs to. It depends on how the line is to be wound on it.

There are two types of bobbins. In general, they differ slightly from each other. Regardless of the type, the coil is divided into two sections. upper and lower. In the first type, the dividing edge does not close into a ring and has a depression.

In the second type, it is solid, but near it there are small through holes on the sides on both sides. The method of winding the thread should be studied depending on which of the above types the coil belongs to.

• The previously prepared six-meter segment must be bent in half. It is best not exactly in the middle, but in such a way that one half is about fifteen centimeters longer.
• Then the place of the fold must be inserted into the recess in the dividing face. One half of the line should be at the top of the reel, the other half at the bottom.
• Now you can start winding directly. You need to wind in the direction of the arrow on the bobbin. When winding, you need to hold the threads so that they do not intertwine and the upper half winds up in the upper part of the spool, and the lower half in the lower part. Each half should have about fifteen centimeters free from the end.
• There are small indentations (or, in other words, grooves) in the upper edge of the bobbin for securing the consumable. The ends of the threads must be inserted into these grooves so that they are fixed against each other.
• The final stage of threading the consumable into the tool. the ends attached to the bobbin must be threaded into the corresponding holes in the trimmer head.
• That’s all. The winding process is complete. Now all that remains is to assemble the head into a single whole. The spring fits neatly back between the bobbin and the head. Then you need to insert the bobbin into the head and press them together.
• It is recommended that the free ends of the thread be pulled out more. To do this, pull the ends of the consumable one by one so that they are removed from the grooves of the bobbin. You can make sure that the cutting element is removed from the retaining grooves by trying to pull the threads a little. they should freely exit through the holes in the head.
• While pressing the bobbin down, you need to put the cover over it. The cover must be screwed to the head so that all the grooves on their bodies are aligned and the bobbin remains fixed between them.
• And finally, the very last action. the head is screwed back into place at the bottom of the tool.

The process is complete. The line is tucked into a reel. The trimmer is ready for further work.

How to wind the line on a trimmer spool: winding methods and video

Any garden owner knows how quickly weeds can fill an area. A trimmer will help to defeat them without undue effort. This incredibly useful device is an indispensable tool for trimming and mowing grass.

It is no secret that an ordinary lawn mower cannot be used everywhere. In contrast, the trimmer can handle even very difficult areas. This is especially true for those tools in which the cutting element is not a knife, but a fishing line.

• Features of the use of trimmers
• Which line to choose

• Thickness selection

Which line to choose

Before you stock up on this material for refueling in the trimmer, you need to decide on the choice. After all, the usual so-called round fishing line is far from the only existing species. How to choose the most suitable one? First you need to determine the working conditions.

Selection by type. Round line is the most common. It will fit any coil with rare exceptions. This type of consumable is suitable for cutting fresh, juicy grass. But with the mowing of the so-called dead wood, such a species may no longer cope. It is pointless to mention attempts to mow bushes with this thread.

In addition to the usual type, there are others with sharp edges. Usually they are made with an asterisk or a square. The presence of sharp edges is the main feature and key difference of these threads.

It is thanks to this feature that the threads of these types are able to mow dry weeds. But sharp-cut threads are not without drawbacks, the main of which can be called rapid wear and strength, which is noticeably inferior to the round type.

In addition to the already mentioned types of woods, there are also interesting and common varieties. Especially among them can be noted fishing lines, inside which a metal wire is stretched. Threads of this type are often used in gasoline-powered tools with an engine more powerful than one and a half horsepower.

Metal-cored threads come in both round sections and sharp edges. Regardless of the type of section, such threads are the best suited for overcoming difficult-to-cut plants. Threads of this type can easily mow not only dry grass, but even small bushes.

The wires with a wire inside compare favorably with other types of consumables for their incredible wear resistance. Unfortunately, this feature has a more than noticeable impact on the price of this type. The cost of yarns with a core significantly exceeds the cost of other types.

Features of the use of trimmers

A trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device like a trimmer exists in several variations:

• petrol;
• rechargeable;
• electric.

As the names suggest, trimmer types differ markedly from one another. But regardless of the type of this tool, a fishing line can be its cutting element. Of course, the line tucked into the trimmer reel is not endless. And sooner or later you will need to replace it with a new one.

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the trimmer, the more active the line is used in it. And, accordingly, the faster it will end. In this regard, the question arises: how to thread the line into the trimmer spool?

Not everyone knows the answer to this question. But the winding of the line on the reel plays an important role in the trimmer operation. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

Second winding method

• A previously prepared segment of six meters in length must be bent exactly in the middle and cut. Thus, two segments of the same length are obtained.
• At one end of each segment, you need to make a small “hook”. To do this, it is necessary to bend a couple of centimeters from the edge and fix it for a short time so that the “hook” does not unbend.
• Then one segment is taken. The hook is inserted into the through hole at the top of the bobbin.
• Now you can proceed to the key stage. winding. The direction in which to wind is indicated by an arrow on the bobbin. It is important to ensure that the line is wound strictly within the upper part of the reel. You do not need to wind the thread to the very tip. about fifteen centimeters should remain free from the end.
• In the upper edge of the spool there are small recesses (so-called grooves) for fixing the consumable. The loose “tail” of the thread must be inserted into one of these grooves.
• The top of the coil is tucked in. Now you need to do the same procedure with the bottom. Take the second piece of thread. The “hook” is threaded through the through hole at the bottom of the bobbin.
• After that, you can start winding the fishing line (within the lower compartment). And for this segment, you also need to leave about fifteen centimeters free from the end. This remaining “tail” must be inserted into the notch opposite to the one into which the end of the first segment was inserted.

The subsequent steps for this type of coils are exactly the same as described for the previous type in paragraphs five to nine.

This is how the line in the trimmer spool changes. There is nothing complicated in the process. And after several refueling operations, all actions will come to automatism.

To visually study the process described above, you can turn to the Internet for help. On the popular YouTube portal there are many different videos showing how to wind the line on the trimmer reel.

How to wind line on a trimmer

Do you have a garden, vegetable garden, garden bed or lawn near your home? Then you probably should have a trimmer. a hand-held mower in order to trim the grass beautifully and remove weeds more often. The technique is convenient, practical and reliable; it requires little maintenance. Difficulties can arise when you need to change cutting tools. They are different at the trimmer. fishing lines and discs, depending on the rigidity of the mown vegetation.

The cutting line of brushcutters is a consumable material, it wears out and decreases during operation. Then you have to put a new one. This article will tell you how to choose and install cutting materials and how to change the line to the disc on the trimmer.

The structure of the line cord matters:

• round. universal, most durable, for coarse grass;
• curly. for soft plants;
• twisted with notches. for thin long stems.

Important! Choose a line of the type and parameters recommended by the brushcutter manufacturer. Such material will work for a long time and with high quality with optimal loads on the product motor.

Choosing a fishing line

The line should be strong, rigid and flexible. in the trimmer, it serves as a working tool for cutting grass. Fishing lines are made of different thicknesses. from 1.2 mm to 4.0 mm. Most models are designed for a maximum thread thickness of 3 mm. What diameter of trimmer line is suitable in one case or another depends on a number of factors.

How to change line on a trimmer

The line is wound on a spool (bobbin), which is located in the trimmer head housing. First, unscrew the head from the brushcutter bar and open its top cover by pressing the side latches. In some models, the case simply unwinds.

We take out the spool, clean it of dirt, remnants of old fishing line. Coils come in one- and two-piece.

Depending on the hardness of the mown vegetation:

• 3 mm. for coarse, tough grass;
• 1.2-1.6 mm. for soft, young.

It is important to take into account that too thin a thread accelerates the wear of the motor, too coarse. will accelerate its overheating and premature failure.

The following line diameters are suitable for different types of trimmer motor:

• electric up to 500 W. 1-1.6 mm;
• electric more than 500 W. 2-2.4 mm;
• gasoline. 2.4 to 3.2 mm.

Change the line to disk

How to change the line on a lawn mower: detailed instructions

In 1971, American entrepreneur George Bollas invented a lawn mower that used a line as a cutting knife. A lot of time has passed since then, the drive has become more powerful, a modern trimmer can easily damage the bark, so the idea itself has transformed into mowing grass around obstacles without damaging the mower cutter itself. For a neat cut around obstacles, a smaller line head can be used and can be easily changed from large areas to delicate mows. However, the cutting tool itself needs to be replaced periodically. We will tell you how to disassemble the head of a lawn mower (trimmer) and wind a new line.

All About Replacing the Line on the Trimmer Head

Choosing a line for the trimmer head

There are many types of heads available to suit different types of line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. over, its cross-section is round (including with a special groove to reduce the noise level), square, twisted and in the shape of a star.

There are no clear preferences, this explains the wide variety of shapes and diameters on the market. The round shape is usually stronger, but has the worst cutting ability and also produces a characteristic sound when rotated. Therefore, sometimes an acoustic groove is made on it, however, the use of this fishing line makes sense only on battery trimmers, in cars with a gasoline engine and a network drive, the sound level of the drive itself practically drowns out the sound from the fishing line. The square has a good cutting ability, and despite the fact that such a line is less strong than a round line, on average it is consumed less. Square fishing line quite easily cuts off the growth of the same willow up to 1 cm in diameter. The star has the maximum number of cutting edges, mows the best and is consumed the fastest.

The next nuance when choosing is rigidity. The fact is that during the production of nylon, a modifier (often maleic anhydride) is added to it, which improves its strength and prevents tearing. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, a seemingly good line that remained for the winter unexpectedly behaves in a completely different way in the spring. it breaks, stops coming out of the reel normally. There is a recommendation to soak the fishing line in water before work, but I do not see much point in this, maleic anhydride interacts with water, but if it is not enough in nylon, then there will be nothing to interact with. Therefore, it makes no sense to stock up on fishing line for a long period of time, breaking or constantly breaking fishing line, which, moreover, does not want to leave the reel itself, can significantly complicate the work.

How to wind a line on a trimmer spool description

Owners of private houses know how necessary this type of tool is, such as a trimmer. It can be gasoline and electric, but they differ in the design of power units. For cutting grass in areas where there are stones, trees and other obstructing objects, a fishing line is used as a cutting device. This consumable wears out during use, so how to wind the trimmer coil, we will consider in detail in the material.

Replacing the line on the brushcutter.

How to wind the cutting line yourself on the reel of the brushcutter (trimmer)

Method 2. how to properly put the line on the reel of the brushcutter with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into the brushcutter is the same as with the first method, and to make sure of this, below are detailed instructions:

• There are two equal length pieces of material that you can use.
• One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be fixed
• Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
• The brace of the fishing line should be hooked on the bracket, and wind it in observing the direction of the arrow
• The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
• Manipulations with the second end of the fishing line are carried out in the same way.
• The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the reel, a cover with latches is installed

The above instructions on how to install a fishing line in a brushcutter will help not only correctly, but also quickly make the replacement procedure. Assembling the trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to conveniently fix the tool. Video instruction is presented below.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but it is used only on petrol cutters, since the exit of such a thread from the reel is difficult, it is used most often with discs into which segments are inserted. How to replace the line in any trimmer The disadvantage of such a product is its fragility.

Most often in gasoline trimmers with an engine with an output of more than 1.5 hp. use cords with a metal cable inside. How to wind the line on the trimmer spool. The line is in and out. for trimmer 2016. Which one. How to replace line in Champion T266 trimmer This line is ideal for cutting dry grass and small bushes. electric. Replacing the fishing line in How to properly lubricate How to choose a fishing line for a petrol cutter. How to change the line to the trimmer filling material. The presence of a core has a positive effect on the wear resistance of this material. The disadvantage of such a cord is its price, which is significantly higher than the above opponents.

The petrol mower is manual. Replacing the line in the reel.

In this video I show how easy and simple it is to wind the line on the reel of a hand-held mower yourself.

Instructions with a step-by-step description of how to wind the trimmer coil and petrol cutters

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually presented on a tip, which will not allow you to make mistakes with the use of the appropriate equipment.

If there is information on the reel about the diameter of the line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. We will consider both methods in detail, and depending on which models of brushcutters and trimmers you use, you decide on your own which option is suitable.

It is interesting! The principle of how to wind the line to guide brushcutters is appropriate not only for autonomous gasoline units, but also for electric trimmers.

How to replace the line in the trimmer

The time will soon come to mow the grass in your area or near your home. In most cases, gasoline trimmers (brushcutters) are used for this. In the role of a cutting unit, a nylon line is used in them. It rotates at high speeds and is excellent for cutting thin grass.
During operation, it naturally wears out and after a while the brushcutter coil becomes empty. But this does not matter, it can be supplemented with a new one. If you bought a trimmer with a tucked line, then you naturally do not know how to tuck new line into the reel. I will show you how to do this and prepare your instrument for the new season in this master class.

The string does not come out

In automatic and semi-automatic reels, the cord is fed without stopping the trimmer. If this does not happen, then:

• the line in the head is not wound correctly, so the reel does not spin;
• the winding of the fishing line is uneven, so the cord gets stuck between the turns and does not come out. so that this does not happen, the thread must be wound carefully, avoiding distortions, turn to turn;
• the ends of the cord coming out of the holes are very short, there is not enough centrifugal force to remove them, so the line is not fed. before turning on the trimmer, it is imperative to adjust the length of the thread and lengthen it slightly, if necessary;
• cord stuck.

On a reel with two antennae

In bobbins of this type, it is necessary to inspect the inner side of the coil and determine the number of grooves for winding the cord provided in it.

Important! If there is only one groove in the coil, then both antennae must be wound along a common groove, if two, then along separate tracks.

For winding, you need to take a piece of fishing line with a length of two to three meters. For spools with one groove, thread the line into the through hole, align the mustache, align and wind it around the spool in the opposite direction of its rotation during operation. If fixing grooves are provided, thread the ends of the cord through them, then pull them out into the outlet, then close the coil and put it back on.

For double-groove spools, the difference is that the string must be folded in half. Next, you need to charge the middle of the fold into the groove between the grooves, then wind each of the pieces of fishing line along its own path, fix the antennae and assemble the coil as well as a spool with one track.

EASIEST WAY TO STRING YOUR WEED EATER

Solving Potential Line Problems

Most of the line problems are the same for different trimmers and are handled in a similar way.

How to properly change the line on the trimmer

The trimmer is a handy and easy-to-use tool for mowing grass and trimming small shrubs and trees. As a cutting element, it often uses a fishing line (string, cord), because it costs less than disc knives and is safer to use. With intensive use of the tool, over time, you will need to change the line on the trimmer. This process is the same on mowers from different manufacturers, be it Husqvarna or Huter, with possible minor differences.

On a reel with one tendril

It is very easy to screw the line onto a reel with one tendril. In such designs, depending on the brand of trimmer, from two to five meters of cord is placed. The edge of the line in the spool must be tucked into a special hole or groove, after which the string is wound in the direction opposite to the rotation of the reel during operation.

Advice! To understand in which direction to wind the thread, you should look at the spool body. usually there are marks on it indicating the direction of the spool movement during operation.

After the line is wound, you need to leave a small piece (15-30 cm), thread it into the spool outlet and reassemble the head.

Fishing line. varieties and the possibility of replacing with other material

The trimmer cord can be of different diameters (from 1.2 to 4 mm), and you need to choose it depending on what kind of vegetation you want to mow. the thicker the line, the coarser the grass it will cope with. Experienced users recommend using a 2 mm line, which is versatile.

The shape of the line can be round (for juicy grass) or with sharp edges in the form of a square or asterisk (for beveling dry grass). The second type is less durable and wears out faster than a round cord.

One of the popular questions regarding the operation of trimmers is whether it is possible to replace a special cord for mowers with other materials, for example, metal or steel cables and strings, wire, etc. You need to know that the installation of such items is not recommended, because with them the trimmer turns into a dangerous technique. During mowing, pieces of wire or metal will constantly break off and fly in different directions, risking injury to the worker. And if they accidentally touch their limbs during work, a serious injury is guaranteed.

For trimmer owners who are interested in whether fishing line can be used, we answer. this is allowed, but it will tear and wear out much faster, which means that it will require frequent replacement.

Advice! Fishing line is well suited for harvesting grass near a fence or metal mesh. instead of wasting an expensive trimmer line, you can charge a large caliber tackle (2-3 mm), which costs much less.

The string does not hold

If the spring looses in a semi-automatic type reel, the line does not hold and unwinds during operation. The cord is pulled out, cut off with a knife, as a result, the owner of the technique notices that the thread is quickly running out.

Advice! To check the tool, you need to remove the protective cover and start the engine. if the line comes out, this means that the spring must be replaced with a new one.

What is needed to replace the cord

With regular use of the grass trimmer, the discs become dull, but they can be sharpened and continued to operate. The line in the reel tends to end, so it becomes necessary to refuel a new one, for which it is necessary to determine the type of head and prepare the cord of the required thickness and length.

So, the mowing head is a cylindrical body in which a bobbin with a fishing line is placed. Such a detail is present both on electric trimmers and on gasoline scythes of any brands, be it Bosch, Makita, Stihl or another brand. There are three types of heads depending on the method of threading and feeding the line.

• The principle of operation of the heads of the automatic group is that they independently feed the line when the mower reduces the engine speed. Such designs are convenient when working on large areas, but they have a drawback. high cord consumption.
• The heads of the semi-automatic group are easy to operate. automatic line feed is performed at maximum engine speed. To release the lanyard blockage, gently tap the tool on the ground and the unlocked thread is pulled out of the spool. Cutting to the required length is made with a knife attached to the protective cover.
• Trimmers with manual cord feed must first be turned off, then pull out the line yourself.

On a note! The most convenient and optimal for the price are semi-automatic reels with cord.

Reels for electric and gasoline braids can be with one or two line tendrils. The former are used for trimming low grass growth, the latter for mowing tall grass and small shrubs.