How To Properly Cut Grass With A Line Trimmer

Country notes
Safety when working with a grass trimmer. How to properly mow lawns, slopes, tall grass with a trimmer. We clean and store petrol and

General principles of the grass trimmer

As a rule, the cutting tool rotates counterclockwise, so you can work with the trimmer in the same way as an oblique-molding, making 1-2 strokes from right to left with a gradual advance of 15-30 cm. Then the cut grass remains on the treated surface on the left. Because the line cuts best with the tip, the swing speed and grip are empirical. With fast wiring, the cut occurs over the entire length of the cutting tool, in this case the motor is unnecessarily overloaded, and the grass is more often wound around the head.

Pruning

It is convenient to cut flower beds, lawns and paths along the edges with an electric trimmer with a lower engine, since its cutting plane can be placed vertically. For an even greater effect on the cutting line, it is useful to dig a groove of about 4×4 cm. Then the line will cut the grass below ground level without touching its surface. The result is a very clean, blemish-free vertical haircut.

How To Properly Cut Grass With A Line Trimmer

High grass

In this case, it is more convenient to mow in both directions. The first pass is from left to right, cutting off the tops of the grass, and then, lowering the tool to the desired level, the lower part is cut in the opposite direction. The cut grass also remains on the treated surface on the left side. If the thickets of weeds are too high, then in order to reduce the likelihood of winding the grass on the drum, you have to mow several times from top to bottom, but this is fraught with increased line consumption.

DIY garden and vegetable garden

Grass trimmer: why and how to use it correctly

Working with a trimmer is quite simple. Easier than with an ordinary scythe. But everywhere there is its own specifics, therefore, before mastering a new technique, you should do what many leave for later. Carefully read the instructions. This is already enough to roughly understand how to use the trimmer, fill it with fuel, figure out how to charge its battery or connect it to the mains.

How to mow with a trimmer

The trimmer should fit well in the hand. Many people prefer a fairly light tool that can be operated on the fly. Otherwise, it should be well balanced, on a comfortable strap or knapsack harness, as it will not be possible to mow properly with a trimmer without this. A very convenient tool with a “bicycle” handle allows you to easily hold the mowing head at approximately a constant height when mowing, and the tip of the cutting tool at the desired distance from the ground. In order for the fishing line to last longer, it is undesirable to bring it close to fences, curbs, brickwork and other solid objects. In addition, the head should not touch the ground unnecessarily.

How to choose a trimmer for a summer cottage? Which is better: gasoline or electric? Find out here.

Slope handling

The slope is also processed according to the principle of “cut grass to the left”, choosing the direction so that its top is on the right. Having reached the end of the section, they return to the starting point, rise higher by the width of the stroke and mow the next strip.

Flat lawn

If the site is large and level, and the grass is soft enough, then it is more convenient to mow along imaginary squares, mentally breaking the entire area into them. Having previously mowed the grass along the perimeter of the first, they continue to work along a tapering square spiral clockwise until the site is completely mowed. Then proceed to the next square. With this method, the cut grass always remains on the treated surface on the left side. In order to mow vegetation to the very root, it is necessary to keep the cutting plane at an angle of 30 °, with the tip of the fishing line almost touching the ground.

Of course, it is better to mow flat lawns with a trolley lawnmower, which allows you to make a smoother cut and collects the cut grass in a special grass catcher. The choice of such a lawn mower is described in this article.

READ  How to Change a Flywheel to a Stihl 55 Trimmer

Grass trimmer: why and how to use it correctly

Working with a trimmer is quite simple. Easier than with an ordinary scythe. But everywhere there is its own specifics, therefore, before mastering a new technique, you should do what many leave for later. Carefully read the instructions. This is already enough to roughly understand how to use the trimmer, fill it with fuel, figure out how to charge its battery or connect it to the mains.

How to mow with a trimmer

The trimmer should fit well in the hand. Many people prefer a fairly light tool that can be operated on the fly. Otherwise, it should be well balanced, on a comfortable strap or knapsack harness, as it will not be possible to mow properly with a trimmer without this. A very convenient tool with a “bicycle” handle allows you to easily hold the mowing head at approximately a constant height when mowing, and the tip of the cutting tool at the desired distance from the ground. In order for the fishing line to last longer, it is undesirable to bring it close to fences, curbs, brickwork and other solid objects. In addition, the head should not touch the ground unnecessarily.

How to choose a trimmer for a summer cottage? Which is better: gasoline or electric? Find out here.

General principles of the grass trimmer

As a rule, the cutting tool rotates counterclockwise, so you can work with the trimmer in the same way as an oblique-molding, making 1-2 strokes from right to left with a gradual advance of 15-30 cm. Then the cut grass remains on the treated surface on the left. Because the line cuts best with the tip, the swing speed and grip are empirical. With fast wiring, the cut occurs over the entire length of the cutting tool, in this case the motor is unnecessarily overloaded, and the grass is more often wound around the head.

How to properly cut grass with a line trimmer

Any owner of a country house or suburban area knows that in summer and spring time it is necessary to constantly look after the lawn, otherwise it will lose its external, attractive appearance. Therefore, many dacha owners are wondering how to properly mow the grass with a trimmer with a fishing line. And before you start learning how to mow, you need to choose the right tool for the site and only then use it correctly on the lawn.

  • Controlling the trimmer, as it may seem to many, is not an easy task, but also nothing special (there is nothing complicated in it) if you properly follow the safety measures and know how to operate it correctly, rather than a garden tool, the cutter of which is a metal disc.

How to properly mow with a line trimmer

Mowing with a line mower is much safer than a trimmer equipped with a cord, but this is not always optimal and profitable. The cutting main element (mechanism) must be selected based on the garden area and the height of the weed.

  • Previously, we looked at how to mow with a line lawnmower in automatic or semi-automatic mode and manual. In automatic mode, the main cutting element (line) is thrown out after each start of the device motor. On the one hand, it is very convenient, but on the other hand, it is not very economical, for example, your garden plot is of a non-standard shape. There are uneven corners, notches, and with each next transition from place to place, you need to turn off the device and then turn it on again. In this case, it is best to use the second, semi-automatic option. This is when the line is fed in the trimmer by pressing a special button located at the very bottom of the drum (in the cutting area). You just need to press the tip to the ground and the line will be thrown out.

If you are an operator, you should understand that the length of the ends of the cutting element (line), which is located on the drum in an extended (working) state, should not exceed 15 cm. This length should be sufficient for the average power of the grass trimmers.

What you need to do to properly, easily and quickly mow the grass with a trimmer with a line in order for the device itself to serve you much longer than usual.

  • Try to keep the main drum (spool) at least 5 cm off the ground.
  • When mowing taller grass, mow the top first, and then get close to the stalks to protect your device from damage and prevent mower failure.
  • In the process of mowing grass, it is imperative to introduce the cutting element (trimmer) in which the reel rotates in the direction.
  • It is best to mow the lawn grass, which is located near the walls of the garden area as a decoration, using only the edges of the line so as not to overload the engine and not wear it out too much.
  • Every 15-20 minutes worked, let the device “rest”.
READ  How To Properly Cut The Ceiling Plinth In The Corners

We carry out the correct mowing in both cases

The device should move correctly in front of you and strictly from right to left, because the grass you mowed will surely fall onto an already mown area, which will give you the opportunity to initially mow the tops of the grass. Then you carry out a reverse motion, due to which you will remove any remaining branches of the grass.

  • When working with large areas of the lawn, it is best to divide the work into several stages, visually dividing the territory into squares. In the process of mowing the grass, you should move along the outside, which will make it possible once again not to trample the grass at the same time, without complicating the mowing procedure for yourself. To make it easier to work, it is best to move from below, walking parallel to the already treated area, and then come back.

With this approach, you can easily use the line trimmer to mow the grass around the trees planted on the site, carefully bypassing them, and at the same time not loading the devices. By mowing the grass in the way we recommend above, you can reduce the likelihood of the grass scattering to the sides, making it faster and easier to cut.

Here are some tips for cutting tall grass:

  • Try not to overload the mechanism during the bevelling process.
  • If tall grass gets tangled on the line, turn off the mechanism immediately so that the motor does not burn out.
  • If your trimmer runs on gasoline, cutting wet grass is strictly prohibited.

How to cut tall grass with a line trimmer

It is advisable to cut tall grass in your garden with a powerful trimmer using thick fishing line. But many, most likely, will agree that in most cases, where the weeds are located, the ground will certainly be uneven, as a result of which the owners of such garden plots have different debris and all kinds of stones. To prevent your expensive device (trimmer) from breaking down the mow of tall grass, it is best and faster to mow in two passes. Those. The first step is to cut the entire top of the grass, identify the more difficult mowing areas and run the mower a second time.

When you are going to harvest the grass (using a trimmer) for hay, and you are more or less versed in the area of ​​your plot, then you can predict the course of the grass mowing in advance. This will be faster, more convenient and easier for you. The main thing in such a situation is not to rush to mow, but to approach business competently with a “cool head”.

Preparing the trimmer for work

Depending on what kind of trimmer you have, you still need to prepare it before starting work. If the trimmer is electric, we need to charge it, or turn it on to the 220 Volt network and start working like that. If you are using the grass trimmer with gasoline fuel, fill the tank. Prepare and check the cutting element, depending on the design. It won’t be superfluous to check the safety of the trimmer. When working with the device, it must be hung on the body and hold onto the handles correctly. Use protective goggles or a special mesh (protective) helmet during beveling.

Preparing the petrol trimmer for work

Pour gasoline (or diesel fuel) into the tank without overfilling it. Two-stroke trim motors require mixing gasoline with engine oil (not car oil) in a ratio of 1: 32-1: 50. You need to know which oil in what proportion is mixed with gasoline for your model. In four-stroke trimmers, you will need to put oil and gasoline in separate tanks. Again, according to the instructions.

Grasp the handle of the device as directed in the instructions. Some trimmers have a double handlebar-like handle. Now follow these steps:

  • Close the air damper;
  • Turn on the ignition circuit using the key or button;
  • If there is a booster mini-pump on the carburetor, pump a little fuel into the engine by pressing the “rocker” lever 3-5 times;
  • Pull the starting cord until there is significant resistance to its movement;
  • Pull the cord sharply up to 5 times.

The engine will start. When mowing the grass, use protective goggles or a helmet with a mesh to prevent the grass from spreading towards the face.

Correct mowing of young grass

To ensure that the device works with maximum efficiency and lasts several times longer than the warranty period, mow the grass correctly, observing the following guidelines.

  • Do not lower the coil (drum) of the device under the very roots of the weed. The distance to the ground is at least 5 cm.
  • When mowing taller grass, cut the top first. Cutting the grass close to the root without removing the top of the stems will entangle the line and stop the drum until it is forced off.
  • Do not mow against the direction of the drum.
  • Mow decorative grass near walls or a fence without moving the trimmer drum too far. This will save the motor from overloading.
  • After every 15 minutes of electric trimmer operation, allow the engine to cool down. It takes at least 20 minutes.
READ  How to Change a Fishing Line Into a Carver Trimmer

But petrol trimmers have a large time reserve. 50 minutes for work and 20 minutes for a break.

Features of the trimmer with line and cord

A trimmer is a more delicate machine than a full-fledged electric or petrol cutter. And the line trimmer is an even more delicate device. Cord. Essentially wire. Can damage the bottom of the trunk in young trees, passing into the root, which is not the case with the line. With thick weed stalks. For example, weeds that have begun tillering. The line may not have time to cut all the weeds.

Despite the obvious convenience, on uneven and irregular areas, by cutting the grass in one place and moving to another, you restart the motor. Exit. Transition to semi-automatic control: the trimmer in the working part has a separate button that is easily pressed when the drum head touches the ground. The line will immediately be thrown out of the cutting end.

The length of the line should not be more than 15 cm in working order. Longer line will get tangled, smaller line will not cut effectively. The optimum line diameter is 2–3 mm.

Preparing the electric trimmer

If it is raining or has just stopped raining, you may get an electric shock when cutting wet grass. Before using for the first time, make sure you have assembled the device correctly. Some models are shipped disassembled. Precise assembly will protect you from injury, and the unit itself from failures and sudden breakdowns. Assembly instructions for the trimmer are described in the owner’s manual.

When using an electric trimmer charge the battery (if the device provides autonomous operation). Lubricate the mechanical gearbox with lithol or grease. If the battery is not in the device diagram – connect the plug to the socket and start working.

How to properly cut grass with a line trimmer?

  1. Features of the trimmer with line and cord
  2. Preparing the electric trimmer
  3. Preparing the petrol trimmer for work
  4. Correct mowing of young grass
  5. Mowing tall grass using line

Mowing your lawn is the main way to keep your lawn area tidy. Not wanting to mow with an ordinary scythe by hand, the modern owner acquires a mechanical scythe or a trimmer. If the choice fell on a trimmer, the question arises of how to carefully mow the grass with it so as not to damage trees and shrubs (if any).

Mowing tall grass using line

For thick stems of grass (weeds), use a more powerful trimmer with thick line. However, in areas where large weeds grow, the soil is often uneven. If it gets caught in clods of dirt, the trimmer motor will brake abruptly. Overuse of this can damage your engine easily. By mowing the top tier, you will see where the grass reaches its greatest length. In deeper places. Focusing on such “height differences”, you will equalize the “mowing” of the lawn, bringing its view closer to the ideal.

The cut grass is suitable for both hay and lawn fertilization. This makes it easier to plan the mowing motion and the process will go faster.

Tips for mowing tall grass are as follows.

  • The engine must not be overloaded.
  • Turn off the engine immediately if the line gets tangled on uneven ground or tall grass.
  • When using gasoline or diesel as an energy carrier, it is impossible to mow wet grass.
  • You need to move the trimmer directly in front of you and to the left, since the cut grass falls on the previously treated sector. Thus, the upper layer of the grass stand is cut off. The layers below it are mowed down when you have already gone in the opposite direction.
  • If the area to be cultivated is very large. Mow one conditional area after another, into which you divided the area before work.
  • Move exactly along the outside so as not to trample the cut grass, making your result inconspicuous.
  • The mowing lines must be parallel to each other. This will allow you to easily bypass the trees encountered on the site, while overloading the motor is excluded.

If you follow these recommendations, the grass will not scatter to the sides during work, and the process itself will be simplified and accelerated at times.

How to properly mow the grass with the trimmer, see below.