How to properly thread the line into the grass trimmer spool

How to replace line in any trimmer

Technological progress provides us with a lot of opportunities to get rid of manual labor. This includes, among other things, mowing grass, which required a lot of physical energy when using a conventional grass scythe. In modern conditions, this process is much easier, because the applied technique minimizes all costs. Devices such as electric and petrol trimmers have firmly taken the place of irreplaceable assistants in gardening. Mowing grass with their help has become more fun than hard and exhausting work.

Structurally, the grass trimmer consists of an engine, a boom and a working body, which, depending on the vegetation being cut, is either a mowing head or a milling disc. And if everything is more or less clear with the cutter, then sometimes questions arise with the nozzle. As a rule, they appear when the line ends.

How to properly wind the line on the reel? Understanding.

So, first unscrew the nozzle. This should be done by rotating the drum to the right. Here we have a drum with the remnants of an old fishing line in our hands. We open it. Most often, the lid is closed with latches that can be opened with a screwdriver, threading it through the holes and slightly pressing. Or you need to squeeze the latch and turn the cover in the direction of the arrow. In this case, the lid itself must be held, since reels with automatic line feed have a spring that, when straightened, can throw out all the inner parts of the drum. Gently pulling out the reel, remove the scraps of fishing line from it.

Now you need to take 5 meters of new line and fold it in half (to find the middle). In the middle part of the reel there is a notch (in some designs. a hole), for which we need to hook our fishing line. There is also an arrow on the spool showing the direction of winding. An important detail. if the reel has two compartments, then one half of the line should be wound in one direction, and the other in the other. When finishing winding, you need to leave 15-20 cm of line free. There are also two notches on the top ring of the coil, through which these free ends need to be passed. We dealt with the winding itself.

The last step in the line replacement process is to assemble the drum. First you need to install the spring and washers in their place. Then, holding the reel with one hand, with the other you need to thread the ends of the line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, tightening the line and being careful not to dislodge the spring. When all the internal elements of the nozzle take their places, you can close the drum with a lid. You just need to make some effort to ensure that the latches fall into place. Voila! The mowing head is ready for use!

How to insert line into the grass trimmer spool and which one is best for this?

Very often, those people who personally own dachas and vegetable gardens are faced with the need to care for the lawn on the site. In such cases, you simply cannot do without a regular manual grass braid or a grass trimmer. The first is slowly fading into the background, and the number of people who use it is getting smaller and smaller. the grass trimmer works automatically and does not require a lot of effort. over, you do not need to have a special skill to use it.

How a grass trimmer works?

The principle of operation of such a device is that the grass is cut by a special fishing line installed on a fast-rotating head. The number of revolutions per minute can reach 8000. In a short time, the line becomes unusable, more precisely, it is erased. Then summer residents have a question: “How to fill the line in the grass trimmer coil”?

Types of lines for grass trimmer

First of all, in order not to resort to frequent replacements, it is better to use a denser line. The number of its types and manufacturing firms is simply amazing. The main parameter of the grass trimmer line is its diameter. It varies from 1.6 to 3.2 mm. The most common type is 2mm line. However, the selection must be made depending on the type of grass trimmer you have.

There are several options for the section of the fishing line. So, it can be round, square, in the form of an asterisk with sharp edges. The last option is the most effective. However, it should only be used on powerful braids and at the same time you need to know how to tuck the line into the reel of the grass trimmer. Therefore, we can conclude that the more powerful your lawnmower, the thicker the line should be.

The process of winding the line onto the grass trimmer is not difficult, but it has its own peculiarities. First, you need to choose the right fishing line, the diameter of which is prescribed in the device’s passport.

First, unscrew the spool cap. Be careful, as the thread can be left or right. The left-hand thread is necessary so that the head of the grass scythe does not unwind during operation.

Threading the Line into the Grass Trimmer

Before threading the line into the spool of the grass trimmer, measure 5 m from the skein (this is the average amount of line installed on the trimmers). Then fold it evenly in half to find the middle. The resulting center must be inserted into a special slot located on the spool. After that, wind the line in the direction of the arrow on the head.

From the above it follows that the process of replacing the fishing line itself is not difficult. Having carried out such a manipulation as winding a fishing line on a reel of a grass trimmer several times, you will bring this process to automaticity. The only thing is that you need to constantly monitor the condition of the fishing line in order to avoid breaking it at the time of work on the site, when there may not be a spare coil at hand.

Now you know how to thread the line into the reel of your grass trimmer and you can do it yourself effortlessly.!

The process of winding the line on a reel

After all the preparatory steps, we need to correctly determine how exactly the fishing line will be washed on your device, by turning the lid or in the opposite direction.
We measure out about 7 mm of cutting material and insert it into the hole of the bobbin with one end. It is worth noting that the line is wound exactly on the model of style mowers from both sides. The direction of winding the line in such models is indicated on the bobbin itself.
The line is brought out to about 17 cm freely so that weeds can be cut off with the ends. We add that it is not worth winding the fishing line on a reel of great length. Leave a distance of about 5 mm from the line to the edge of the bobbin.
The two ends of the line are inserted into the holes in the bobbin. Both of these ends must be securely attached to the body of the device.
The springs removed from the coil (if any) are inserted in the same way as they were removed, i.e. into the bobbin and the head body itself.
To determine if you have correctly inserted the line into the grass trimmer, you need the element itself (the bobbin) to slide easily into the head body of your device. If necessary, pull the free ends of the line outward. To achieve this, you need to pull the line out of the groove with a sharp movement through the holes in the bobbin.

So, let’s say you figured out how to quickly, and most importantly, correctly wind the line on the reel of the STIHL grass trimmer. All that is left for you is to insert everything correctly into the grooves and fix the main cover to the device. Then you can press on the bobbins themselves and make counterclockwise movements until you feel the stop. If you do not feel the emphasis, then most likely you have not tucked the line correctly and you will have to start everything from scratch.

A couple of tips

If the line was wound correctly by you, then when you press the bobbin button, the cutting element should be automatically pulled out. The line for your mowing device is one of the most important elements, without which the grass trimmer can lose all its functionality. You can say that the line (cutting element) is the heart of your mower. Therefore, when buying a fishing line, pay first of all to its quality. When purchasing a fishing line of this or that company, be sure to compare it with the quality of the old fishing line.

How to insert line into the spool of the STIHL grass trimmer

A grass trimmer is one of the most common tools that you can use to quickly and easily cut grass, small shrubs, lawn grass and other weeds. It’s not a secret for anyone that in order for the mowing of grass to be successful, it is necessary to use the tool correctly and correctly handle individual cutting elements.

In trimmers, it doesn’t matter what fuel they run on, special cutting attachments (knives, discs) are used, and some grass trimmers are supplied to the market in the heads of which such a cutting element as a fishing line is installed, and therefore many are wondering how to fill the line into the spool STIHL grass trimmer, if the skills as such are not available at all.

Cutting attachments in the form of knives can be sharpened, but the fishing line (also cutting elements), but tends to be consumed. Below we will talk about how to properly thread the cutting element into the reel of the STIHL grass trimmer. the line.

Preparing the grass trimmer spool for winding

Initially, as a rule, the coil is installed to the head of the device itself. The coil consists of two parts. a cover and a spring.

Whichever company you have a grass trimmer, the preparation steps are the same for all types. Disassemble the device, or rather remove the coil from the grass trimmer head. To do this, press until it stops on the latches located on the sides of the head body, and turn the head clockwise.
To open the mowing head without problems, press the side latches, if you cannot do this with your hands, use a flat screwdriver to help. We take out the coil from the head.
In order to choose the right line for your equipment, on the inside of the reel, digital designations must be applied, which indicate the thickness and type of acceptable line. All designations are indicated, as a rule, in millimeters.
If you did not find any numbers, then the maximum allowable diameter of the fishing line can be determined by the through hole for inserting the fishing line. The line should run smoothly back and forth.

What can be used instead of fishing line

If instead of a special cutting element, say a fishing line, you install a metal cable, then your grass trimmer can “turn” into a real dangerous weapon not only for you and your eyes, but for all the people around you nearby. This is due to the fact that during the operation of the grass trimmer, the steel cable will constantly work, which will lead to entanglement, and small pieces of it can scatter on all sides with great speed.
The same can happen if you use copper wire instead of a steel cable, but in this case the pieces of separation from the copper wire will be slightly larger and may cause you even more injury. And if God forbid, you accidentally catch such a cutting element on the leg, then after that a deep cut in soft tissues is 100% guaranteed, and in some cases, all this can lead to amputation of small limbs (fingers) of the legs and even hands. Therefore, our advice to you, do not use any other cutting elements, except for the fishing line, for your own safety and those around you.

How to wind line around the spool of a grass trimmer: key points

Thickness selection

In addition, you should pay special attention to the thickness of the consumable. For mowing young grass, a thread with a diameter of one and a half millimeters is suitable.

The larger the diameter of the thread, the drier and coarser weeds it is capable of overpowering.

When choosing a fishing line by thickness, there is one “but”

It is important not only to assess the capabilities of the material, but also to take into account the features of the grass trimmer. Be sure to check the user manual that came with your tool for information on cutting element requirements.

Using the wrong thread can damage the tool. Using a thread that is too thick will overload the machine’s motor. And the use of a thread that is too thin will significantly increase the wear of the twisting mechanism.

That is why the choice of consumables must be approached no less responsibly than filling it into the grass trimmer. When a suitable fishing line is found and purchased, you can begin to consider ways of winding it on a reel.

How to wind the line around the mowing head of a grass trimmer or brushcutter

The video shows in detail how to wind the line onto the spool of a grass trimmer or brushcutter. Refueling with mowing line.

Solving Potential Line Problems

Most line problems are the same for different trimmers and are handled in the same way.

What line is used for the grass trimmer?

Stronger. round;
For mowing soft vegetation. curly;
For mowing narrow grass. with notches;
Special. matches certain types of grass trimmer.

The section of the cutting thread must match the vegetation to be cut.

If you need to change the fishing line, then you need to select specifically the type that is recommended by the manufacturer of this particular grass trimmer model, in other words, the thickness of the cutting thread should be suitable for the motor power and the size of the unit.

It is better to choose a specialized cutting thread. It is worth soaking the fishing line for a while if you plan to change it in the reel.

After soaking, it gains elasticity and becomes stronger.

The cutting thread can be made from various components. Common among them is nylon.

This material is characterized by the highest degree of wear resistance, the ability to withstand different temperatures and the highest loads.

Restring a 1 string spool on a string trimmer weed eater EASY!!

Nylon line can be stored for a long time, it does not dry out and does not lose its strength.

Therefore, its service life can be quite long.

The reels or heads for the brushcutter have a different structure:

Line replacement process

For each trimmer, the manufacturer recommends a fishing line, or cord, of a certain diameter. a reel is made for it. It can be from 1.2 to 4 mm: you need to look at the instructions for what line sizes are acceptable for your tool. For example, many trimmers have a maximum value of 3 mm (recommended for tough grass). a thicker cord cannot be fitted.

For mowing young, soft vegetation, a thin line with a diameter of 1.2. 1.6 mm is suitable

Also, when choosing, pay attention to the structure of the cord: round is the most durable and suitable for coarse grass, curly. for soft, twisted or with notches. for thin stems. Depending on what kind of grass grows on the site. lawn or weed, buy the appropriate consumable

It’s important to know! Buy only branded line recommended by the grass trimmer manufacturer. It is made of quality materials and is durable. it will cut the grass perfectly and not wear out so quickly

Helpful Hint: Place a piece of cord in water for 30 minutes, then it will become more elastic and stronger.

The line is wound on a spool, which is hidden in the trimmer head housing. To get to it, you need to disassemble the element. On the case there are latches-latches, when you press them, the case cover can be easily removed. Sometimes disassembly is carried out by untwisting the case.

Be careful! Remember in what order the elements are installed, how the spring and the fixing screw are located inside the head. Stack all the parts neatly in one place so that nothing gets lost and there are no problems during assembly.

Coil type	With dividing edge	Without dividing board
Line winding	1. The prepared piece of fishing line is folded in half and the place of the fold is caught by the groove in the dividing edge. Some coils do not have such a groove, then the fishing line is cut into two parts and each of the segments is inserted into the upper and lower parts, clinging the ends to special holders. 2. Each end of the line is placed in its own groove. 3. Rotate the reel so that the line winds in the direction of travel indicated by the arrow. Both ends are wound in the same direction. 4. The free ends of the line, 15. 20 cm long, are temporarily placed in special holes on the spool. They should be opposite each other. The hole on the body is selected according to the diameter of the fishing line (it is usually written next to it what diameter it is designed for)	1. A piece of fishing line is cut into two parts. 2. Next, you need to fix the ends: they are inserted either into the holes in the upper part of the coil, or into special mounts on the roller itself. 3. Winding is carried out in the direction indicated on the spool. Both segments lead parallel to each other, preventing them from crossing. 4. The free ends are spread on two opposite sides and, if there are slots in the coil, they are fixed there. The cut must match the diameter of the line

We suggest that you familiarize yourself with: Fishing for pike with a wobbler. simple rules

We have described how to wind the line into the reel of a double-barbed grass trimmer. This is the most common option. But there are other ways as well. For example, if there is one antenna in the mowing head, then winding is carried out without folding the line. Rotate in the direction indicated on the spool body, and the free end of the cord is temporarily fixed in the slot on the body.

Helpful hint: when winding the line, proceed carefully, do not stretch it, so that it does not sit very tightly in the reel. It is necessary to ensure its free movement for subsequent pulling.

After the line is wound on the spool, it is necessary to assemble the body. Position the spool so that the ends of the line can be pulled into the outlets of the trimmer head. The slots in the spool where they were temporarily inserted will prevent them from slipping out. If there are no such slots, hold the ends with your fingers when placing the coil in the body.

Which line to choose

Before you stock up on this material for dressing in a grass trimmer, you need to decide on the choice. After all, the usual so-called round fishing line is far from the only existing species. How to choose the most suitable one? First you need to determine the working conditions.

Selection by type. Round line is the most common. It will fit any coil with rare exceptions. This type of consumable is suitable for cutting fresh, juicy grass. But with the mowing of the so-called dead wood, such a species may no longer cope. It is pointless to mention attempts to mow bushes with this thread.

In addition to the usual type, there are others that have sharp edges. Usually they are made with an asterisk or a square. The presence of sharp edges is the main feature and key difference between these threads.

It is thanks to this feature that the threads of these types are able to mow dry weeds. But sharp-cut threads are not without drawbacks, the main of which are quick wear and strength, which is noticeably inferior to the round type.

In addition to the already mentioned types of woods, there are also interesting and common varieties. Especially among them can be noted fishing lines, inside which a metal wire is stretched. This type of thread is often used in gasoline powered tools with an engine over 1.5 horsepower.

Metal-cored threads come in both round sections and sharp edges. Regardless of the type of section, such threads are the best suited for overcoming difficult-to-cut plants. Threads of this type can easily mow not only dry grass, but even small bushes.

The wires with a wire inside compare favorably with other types of consumables for their incredible wear resistance. Unfortunately, this feature has a more than noticeable impact on the price of this type. The cost of yarns with a core is much higher than the cost of other types of yarns.

How to properly tuck the line into the grass trimmer: instructions

If you set the line incorrectly, the unit may break down and you will have to fork out to repair it. Therefore, before proceeding with the procedure, be sure to read the detailed step-by-step instructions. It’s easy to learn how to do this and in a few minutes you can go mowing the grass.

How to tuck the line into the grass trimmer:

How To Tips for Easy Restring of Weed Eater with 2 strings

First you need to remove the nozzle that is located on the gearbox. This is easy to do: the connection is the hole located on the side of the bottom washer and the recess. You can find the grooves on the axis. Be sure to insert a screwdriver to prevent the shaft from turning. When removing the nozzle, you need to twist to the right, not to the left. Disassemble the coil. sink the clips located on it into the body, then gently squeeze the edges.
How to handle the line automatically? You need to handle it as carefully as possible, otherwise a spring will fly out of it (the same applies to fishing line with a semi-automatic mode). Hold the parts with your fingers and take your time.
Spool with a through hole on the body. you need to pull the line through both holes (outer and inner). Then turn the button and release the thread.
If the reel functions only with 1 cutting element, the procedure is quite simple and quick. You will find a small hole in the inside of the spool that will keep the thread in place. You need to insert the end of the thread into the hole, then start winding. This should be done in the opposite direction in tone to the movement of the coil. Take a closer look. perhaps your reel model has an arrow, it indicates the direction in which you need to wind.
The end of the thread is fixed with a groove located in the inner part of the bobbin. Leave a long piece of line outside.
If your model does not have a groove, hold the end of the thread with your hand, then install the top of the spool and thread the end of the thread into the hole.
Place the spool in the grass trimmer and get to work!

How to properly thread the line into the grass trimmer spool

You don’t have to work on site for hours on end to mow your lawn and give it a well-groomed look. A device such as a grass trimmer can handle any volume of work as quickly as possible. This type of technique can cut grass of any length and density, it all depends on the model chosen. In order for the unit to work fully and perform its main function, you need to refuel the line, otherwise the grass trimmer will not be able to complete the task.

Line selection

First of all, you will need to choose the right line. Do not do it “at random”, as it all depends on the model of the unit. Pay attention to indicators such as the diameter of the thread, as well as its cross section. You can find information about the diameter in the instructions for the trimmer. The second indicator (section) depends on what types of work you are going to perform. If this is a soft young grass, round is suitable, if it is hard, choose a square or 5-sided section.

How much line will you need?

For normal operation of the grass trimmer, 3-4 meters of material is enough. The length of the thread depends on the dimensions of the spool. The larger it is, the longer the line.

Two cutting elements

If your grass trimmer has a spool with not one, but two cutting elements, unwind the required amount of line and thread the thread through the hole, the line should be divided into 2 equal lengths. Then start winding 2 pieces at the same time. When almost all of the line is wound, leave short ends and clamp them in the grooves. This method is suitable for a single groove spool.

If the device has not one, but two grooves, you need to insert the fishing line in a different way. fold the cut thread in half, at the end you will have a loop. You need to insert this end into the groove, it is located between the two grooves. Each groove has one end. Assemble the coil in the same way as in the previous case.

How to properly thread the line into the grass trimmer spool

If the instructions above didn’t work for you, check out this video. You will clearly see how to thread the line step by step.

What line is used for the grass trimmer?

There are several types of fishing line:

Stronger. round;
For mowing soft vegetation. curly;
For mowing narrow grass. with notches;
Special. matches certain types of grass trimmer.

The section of the cutting thread must match the vegetation to be cut.

If you need to change the fishing line, then you need to select specifically the type that is recommended by the manufacturer of this particular grass trimmer model, in other words, the thickness of the cutting thread should be suitable for the motor power and the size of the unit.

It is better to choose a specialized cutting thread. It is worth soaking the fishing line for a while if you plan to change it in the reel.

After soaking, it gains elasticity and becomes stronger.

The cutting thread can be made from various components. Common among them is nylon.

This material is characterized by the highest degree of wear resistance, the ability to withstand different temperatures and the highest loads.

Nylon line can be stored for a long time, it does not dry out and does not lose its strength.

Therefore, its service life can be quite long.

The reels or heads for the brushcutter have a different structure:

What you need to know about grass trimmer line

A fishing line is a consumable that is made of nylon and serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has a different thickness, which depends on its application on the corresponding tools, electric low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline grass trimmers with brushcutters (from 2.4 up to 3.2 mm).

The more powerful the tool, the correspondingly thicker the cutting equipment should be. This affects not only the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the coil of your grass trimmer, then it is time to change and reload the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the step-by-step instructions for replacing the fishing line in the grass trimmer reel.

Now only I bite!

I caught this pike with a bite activator. No more fishing without a catch and looking for excuses for your bad luck! It’s time to change everything. The best bite activator of the year! Made in Italy.

Step-by-step instructions on how to wind the reel of the grass trimmer and lawn mower

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually presented on a tip, which will not allow you to make mistakes with the use of the appropriate equipment.

If there is information on the spool about the diameter of the line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. We will consider both methods in detail, and depending on which models of brushcutters and trimmers you use, you decide on your own which option is suitable.

It is interesting! The principle of how to wind the line to guide brushcutters is appropriate not only for autonomous gasoline units, but also for electric trimmers.

How to catch more fish?

One-string. In the modification of such a grass trimmer there is only one working line. This unit is used mainly for small jobs, such as trimming the grass.
Two-stringed. They can be both automatic and automatic. Here the package includes two strings. Used such a grass trimmer for mowing and clearing areas.

Instructions for correctly winding the cutting thread onto the spool of the grass trimmer:

First of all, you need to disassemble the head. To do this, press the latch and turn the cover to the side. Next, the spool is removed.
Measure out the required amount of cutting thread and insert it into the slot.
Wind the line on both sides in the direction of the arrow.
Leave the ends 15 cm long uncoiled.
These ends fit into opposite slots.
Then the ends are fixed in the hole on the head.
After that, the spool is carefully inserted into the body, for this you need to slightly press on it.
If necessary, you can pull the remaining ends of the thread outward. To do this, first pull one end of the thread, and then the other so that they can easily pass through the slots on the head.
Now you need to collect the grooves on the body and screw the cover.
Then press the spool and try to twist it all the way. If you hear a click, the spool has clicked into place.
Next, you need to pull the free ends of the thread to the end.

Method 2. how to properly put the line on the reel of the brushcutter with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into the brushcutter is the same as with the first method, and to make sure of this, below are detailed instructions:

There are two equal length pieces of material that you can use.
One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be fixed
Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
The fishing line should be hooked onto the bracket, and wind it in observing the direction of the arrow
The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
Manipulations with the second end of the fishing line are carried out in the same way.
The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the coil, the cover with the latches is installed

The above instructions on how to install a fishing line in a brushcutter will help not only correctly, but also quickly perform the replacement procedure. Assembling the grass trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to comfortably fix the tool. Video instruction is presented below.

How to wind the line around the mowing head of a grass trimmer or brushcutter

The video shows in detail how to wind the line onto the spool of a grass trimmer or brushcutter. Refueling with mowing line.

How to properly wind the line around the spool of the grass trimmer

Many, having worked out the factory line on a recently purchased trimmer, try to wind a new one, but they cannot, because they do not know how to properly wind the line on the spool (bobbin) of the grass trimmer. It seems that there is an instruction, but it still does not work. Let’s try in this article to deal with this issue.

So, in order to wind the line, you first need to remove the coil from the grass trimmer. this will be more convenient. How to remove will depend on the type of grass trimmer.

Removing the coil from the grass trimmer

On small electric bottom motor trimmers (when operating near the ground), the reel usually has two buttons on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to wrap the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the grass trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gear at its end (on such grass trimmers, in addition to fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver crawls even deeper and the coil will lock. Now turn the whole coil clockwise (since the thread is left-hand) and remove it from the grass trimmer. Next, we disassemble the coil. It can be assembled with latches or twisted with a lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you also need to make sure that the spring inside is not lost.

than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. After winding the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inner part of the reel and designed so that the line does not unwind at the time of collecting the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the grass trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both antennae are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. A reel with one groove should have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, fix the resulting ends in special grooves, and if they are not there, we hold them with our fingers. We pass both ends into the existing holes on the outer casing of the coil. We collect the coil and attach it to the trimmer.

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the fold into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also reels in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, without winding, are threaded completely through the holes on the outer body of the reel, collect the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Rotate the button. the fishing line itself is wound inside. At the same time, it will not work to turn it in the “wrong” direction, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!

We will learn how to thread the line into the reel of the grass trimmer and which one is better to use for this.?

How a grass trimmer works?

First of all, in order not to resort to frequent replacements, it is better to use a denser line. The number of its types and manufacturing firms is simply amazing. The main parameter of the grass trimmer line is its diameter. It varies from 1.6 to 3.2 mm. The most common type is 2mm line. However, the selection must be made depending on the type of grass trimmer you have.

First, unscrew the spool cap. Be careful, as the thread can be left or right. The left-hand thread is necessary so that the head of the grass scythe does not unwind during operation.

Threading the Line into the Grass Trimmer

There are such models in which the winding place is divided into two halves. Therefore, one is often wound clockwise, and the other. vs. Having reeled the fishing line completely, the ends are threaded through special holes. A cover is put on top of the head.

Now you know how to thread the line into the reel of your grass trimmer and you can do it yourself effortlessly.!

Sources:

http://fb.ru/article/127352/kak-zapravit-lesku-v-katushku-trimmera-i-kakuyu-luchshe-dlya-etogo-ispolzovat
http://agrarian-blog.ru/kak-zapravit-lesku-v-katushku-trimmera-shtil/
http://waysi.ru/uchastok/landscape/kak-namotat-lesku-na-katusku-trimmera-patriot.html
http://mensweekly.ru/page/kak-zapravit-lesku-v-katushku-trimmera-sovety-video
http://arendavlg.com/gazonokosilki/kak-namotat-lesku-na-katushku-trimmera-klyuchevye-momenty.html
http://instrument-tehnika.ru/kak-pravilno-namotaty-lesku-na-katushku-trimmera/
http://autogear.ru/article/127/352/kak-zapravit-lesku-v-katushku-trimmera-i-kakuyu-luchshe-dlya-etogo-ispolzovat/

Grass Trimmer grass, line, properly, thread