How To Properly Wind The Line On A Lawn Mower

How to change line to trimmer

Below we have provided Step-by-step instructions for replacing a whine trimmer.

The first thing to do is unplug the tool and turn off the engine. Then you need to remove the trimmer head. This can be done by using a simple screwdriver, lowered it into the hole of the gearbox to prevent the shaft from turning. And then just Unscrew

  • How To Properly Wind The Line On A Lawn Mower
  • They are usually unscrewed in a clockwise direction, but different models have different mechanisms, so it may be necessary to twist in the opposite direction. But if suddenly, for some reason, you cannot figure it out, then we strongly recommend that you refer to the user manual to understand how to disconnect it

    Second. After removing the mowing head, open it. This can be done by means of clamps, which are located opposite each other. Pressing on them, you can remove the head cover, and then pull out the spool on which the fishing line is wound. By pulling it out, you can determine what type it belongs to. There are bobbins one-piece and two-piece

    We analyze how to thread the line into the trimmer spool in two versions

    So, option one. load the fishing line into a single-section reel. The prepared piece of thread is folded in half and pushed into the spool. Then, we begin to wind both ends in the same direction, which will be indicated by the arrow on the spool. At the end of the winding, do not forget to check that the different ends of the thread are looking in different directions.

    Option two. winding the line with a two-piece reel. The pre-prepared thread is divided into two parts, and its ends, must be fixed: this must be done by placing them in special fasteners

    Winding is carried out, as in the first case, along the arrow indicated on the spool. Both segments must be wound so that they do NOT overlap. Further, the ends of the thread must be fixed in the grooves and spread on opposite sides.

    The spring is then inserted into the reel and the whole thing is placed in the mowing head. When placing the coil in the trimmer you need to gently hold the spring parallel to insert the line into the cut of the mower head. And in the end, it just needs to be secured with the final part, that is, with a lid.

    After threading the trimmer, you need to check it. If you did everything correctly, everything will work, but if you make a mistake, we recommend that you read the article again, or even better, if you look at how to install the line on the reel in the trimmers.

    How to remove the line from the trimmer spool

    Over time, the cutting element of the head wears out, and it becomes necessary to pull out the remnants of the old line. But not everyone knows how to do it. Our step-by-step instructions plus how to pull the thread from the trimmer spool, which you can find on the net, will help in solving this issue.

    The mowing head must be disassembled

    Remove the cover using the clips

    Cleaning up the remnants of cutting material

    Complicated? Of course not. But if, nevertheless, doubts creep into you that for some reason you will NOT be able to do this, then of course find and see how to pull out or how to wind the thread onto the spool of the lawn mowers.

    How to wind the line onto the trimmer spool

    05 July 2018

    The trimmer is a great solution for those who have a large garden or lawn near the house, which needs to be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, it will become necessary to replace certain elements, and this will have to be learned.

    How can this be done? To replace the main cutter, you must first select it correctly. In principle, the lawn mower instruction manual should indicate the diameter of the thread to be used in it.

    When you have acquired the required cutting element, try to install it correctly. It should be noted that there are a huge number on the Internet. Which will help you figure out how to properly thread the line into the trimmer spool.

    How to replace the line with an electric trimmer

    In fact, it makes no difference which oblique you use, be it electric or gasoline. Threading is the same. The only difference is that if you use a gasoline scythe, you get more freedom, since it is NOT limited by the cable, which is present on the electric scythe

    Yes, do not hesitate to use special rollers for installing or threading the line in an electric scythe, which can teach you much faster than simple reading.

    How to properly wind the line on the trimmer spool

    Many, having worked out the factory line on the recently purchased trimmers, are trying to wind a new one, but they cannot, because they do not know how to properly wind the line on the spool (bobbin) of the trimmer. It seems that there is an instruction, but it still does not work. Let’s try in this article to deal with this issue.

    So, in order to wind the line, you first need to remove the coil from the trimmer. this will be more convenient. The removal method will depend on the type of trimmer.

    Removing the coil from the trimmer

    On small electric trimmers with a bottom-mounted motor (when it is in the ground while working), the reels usually have two keys on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

    On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to grab the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the Trimmer Bar. Having unscrewed the lamb, carefully remove the entire coil, trying NOT to lose the spring inside.

    On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver does NOT crawl even deeper and the coil will lock. Now steep the whole coil clockwise (since the thread is left-hand) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using snaps or a twisted lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection between the two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you also need to make sure that the spring inside is not lost.

    than 200 types of trimmers in one place at the lowest prices. Click and watch

    Now, having removed and disassembled the coil, we proceed, in fact, to winding.

    Winding process

    If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a hole on the inside of the reel for the fixing line, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. I wound the fishing line, we leave a small piece of it unwound to put it out. We fix this piece in a specially groove located on the inner part of the reel and designed so that at the time of collecting the reel, the line does NOT unwind. If there is such a groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and threading the outer piece of fishing line into the existing hole, collect and put the coil back on the trimmer.

    If the coil is designed to work with two tendrils, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. Reels with one groove should have a through hole through which the fishing line is threaded. We rewind 2-4 m of fishing line, threading it through this hole so that the fishing line sticks out equally on each side. And we simultaneously wind both tendrils of the fishing line in one direction, opposite to the direction of rotation of the coil to the trim tabs and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, the resulting ends We fix in the Special grooves, and if they are not there, we hold them with our fingers. Threading both ends into the existing holes on the outer casing of the coil. We collect the coil and fasten it to the trimmers.

    If there are two grooves, fold a piece of fishing line 2-4 m long in half. Insert the loop obtained at the place of the fold into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

    There are also spools in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, and not winding, are threaded completely through the holes on the outer body of the reel, assemble the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Turning the button. the line itself is wound inside. In this case, twisting it in the “wrong” direction will NOT work, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

    That’s all on this issue. Happy winding!

    How to quickly and easily remove the coil with your own hands

    Before replacing the old line with a new one in the detachable trimmer spool, you must remove the head.

    The process is completely simple, even beginners can do the job:

    • Remove the upper fixing cover.
    • Remove the removable spool.
    • Get the spring out, if any.
    • Screwdriver Unscrew the bolt.
    • Remove the housing from the shaft.

    What are the trimmers and features of their use

    The trimmer is useful for mowing small or difficult areas, such as near hedges, between beds and along paths. Today manufacturers produce a wide variety of gasoline, electric and battery models, which can be selected for any owner’s request.

    A fishing line is used as a cutting element of the trimmer. In the process of work, sooner or later, its length will end, and then the owner will have a question of how to correctly replace and fix the thread tucked into a removable coil.

    How to wind the line correctly: replacement features depending on the type of removable trimmer coil

    To figure out how to tuck the line into the removable trimmer head, the following recommendations and instructions will help.

    Auto feed trimmer: how to wind the line into the removable spool

    Some models of trimmers have a reel, the threading of which is automatic. It is enough for the owner to fix the ends in the head, after turning on the equipment, the mechanism will perform all the winding manipulations on its own.

    How to wind the line on the detachable reel trimmer with two tendrils

    You can see before work. And also take into account the following recommendations.

    • If there is only one track, both threads are wound parallel.
    • If there are two tracks, each piece is wound in a separate groove.
    • Wind the threads in the opposite direction to the rotation of the head.
    • The length of the risers does not have to exceed fifteen centimeters.
    • Thread the ends into the outlet holes.
    • Assemble the head and check the trimmer performance.

    How to wind the line correctly on the spool of the trimmer with one tendril

    Most often, a thread up to five meters long is used. The procedure consists of the following steps:

    • Bent the cord with a loop and insert into the groove of the head.
    • Wind the thread in the direction opposite to the marks on the body. They indicate the direction of movement of the head.
    • Leave the end of the thread up to fifteen centimeters long to increase the centrifugal force.
    • Thread the free end through the spool outlet.
    • Assemble the trimmer head.

    By quality

    Before you put the line on the trimmer, you need to Pay attention to the section of the cord:

    • Whining with a circular cross-section is the most common option. They cut the grass perfectly even in difficult areas;
    • Spiral line is suitable for thin grass. It is not very durable and is NOT suitable for old thickets;
    • A cord with notches and sharp edges is chosen for mowing weeds;
    • A fishing line with a variety of geometric sections will help mow the lawn more evenly, but the strength of the consumables is low.

    The owner of the lawn mower should know that it is absolutely forbidden to use metal wire, fishing thread and various strings.

    How to properly wind the line around the trimmer: Step-by-step guide and instructions

    A beautiful lawn will only look truly well-groomed if you regularly mow the grass. A trimmer is best for tackling difficult areas. Any owner of the unit will sooner or later face a solution to the problem of how to wind the line on a reel, because wrong actions can not only worsen the quality of the mowing, but also disable the equipment. Today in the Homius review we will tell you about all the methods and nuances of replacing the fishing line and the features of choosing consumables.

    Things to consider when choosing a line

    It is important to choose the right material before inserting and locking the line into the detachable trimmer spool.

    Rating of the best petrol trimmer models. An overview of manufacturers and models, as well as useful tips from experts, considered in this review, will help in a difficult choice among many device models.

    Step-by-step instructions for threading the line into the trimmer

    • Press the clips inward to click and remove the cover from the mowing head.
    • Turn the spool gently, it will free itself from the holder, and now remove it.
    • Cut two identical pieces of line (the edge of the line should be cut at an angle. This will make the job easier). Take one of them and insert the end of the line into a special on the reel (there may be hooks, ears, clips). Then wind the string in the direction of the arrows. Distribute the line evenly, tightly. Attach the end of the string to the specially provided hole in the reel.
    • Do the same for the second part of the line, only the end Thread on the spool from the opposite side.
    • Return the line spool to the mowing head. Pull out the ends of the line through the holes in the spool and thread them into the special connector of the head.
    • Spread out the fishing line gently and close the lid. Cut off excess fishing line, leaving 12-15 cm. Each edge.

    Everything is ready. The trimmer refills the line and is ready to go. Now you can happily walk along the slopes of your favorite meadow, summer cottage, local area.

    It is only important to remember that not only the quality of the work performed, but also your safety will depend on how you load the cutting line into the trimmer.

    Instructions for refueling the line Trimmer (lawn mowers)

    Trimmer head modification

    Trimmer mowing heads can be of various modifications: single-line for trimming the lawn (mows with one line of line), two-line for mowing grass and Land clearing with automatic line feed or manual line length adjustment.

    Modern growers are increasingly offering gardeners universal trimmers with two-line automatic mowing heads.

    Line selection

    In order for the trimmer to work “like a clock”, it is necessary to choose the right line, that is, choose it taking into account the trimmer model and type of work. There are two fundamental parameters in this matter. This is the diameter and section.

    The diameter of the fishing line must correspond to the one recommended for this model (it must be specified in the product passport).
    The cross-section of the fishing line is round, square, with sharp edges (pentahedron). A round line is designed for mowing young grass and lawn, square and pentagonal line will come in handy if the grass is hardened and weeds have grown on the lawn.

    Brief introduction

    To begin with, it must be said that knives or fishing line can be used as a cutting element in trimmers. Both types have their advantages and disadvantages.

    So, knives do a much better job with shrubs and dry wheatgrass, but polymer thread is much cheaper and more affordable. In addition, the 4 mm trimmer line also allows you to cut fairly tough grass. Of course, you cannot compare with a knife, but the efficiency is also not bad.

    Note that even in the latter case, you need to know exactly what its diameter is used in your trimmer. Manufacturers do not take all the values ​​from the ceiling: if you take a larger fishing line, then the engine is heavily overloaded, which may well cause the latter to fail.

    How to properly install the line on your lawn mower. Line Threading Instructions Trimmer

    Getting started

    Then the remaining end of the line is threaded through the hole in the protective cover. After that, the reel and its protective cover are connected, and this time a piece of fishing line is threaded into the hole on the protective cover.

    The assembly is pushed onto the trimmer by turning clockwise until a clearly audible click is heard. By the way, before installing the line on the trimmer, figure it out better with its design. Otherwise, you can easily break something.

    That’s all. The tool is put into working position, turned on, after which the extra piece of fishing line is cut into a specially made blade for this purpose.

    So you learned how to properly tuck the line into the trimmer!

    We will learn how to properly tuck the line into the trimmer

    But beginners rarely know even the most basic rules of caring for this technique. So, the most common question is how to properly tuck the line into the trimmer.

    Let’s get started

    Before you can properly tuck the line into the trimmer, you need to cut off the required amount. DO NOT be greedy, as for the first time and five meters is enough for training. To do this, the protective cover is removed from the trimmer coil, and one end of the fishing line is clamped in a special clamp (or slots).

    You need to rewind evenly, trying NOT to overtighten. In general, you need to fill the spool until the line layer is equal to the edge of the spool. It should not lie too tightly, slightly straightening after putting on the casing.

    How to properly install the line on your lawn mower

    Similar entries. Getting started

    Then the remaining end of the line is threaded through the hole in the protective cover. After that, the reel and its protective cover are connected, and this time a piece of fishing line is threaded into the hole on the protective cover.

    The assembly is pushed onto the trimmer by turning clockwise until a clearly audible click is heard. By the way, before installing the line on the trimmer, figure it out better with its design. Otherwise, you can easily break something.

    That’s all. The tool is put into working position, turned on, after which the extra piece of fishing line is cut into a specially made blade for this purpose.

    So you learned how to properly tuck the line into the trimmer!

    Step-by-step instructions for threading the line into the trimmer

    • Press the clips inward to click and remove the cover from the mowing head.
    • Turn the spool gently, it will free itself from the holder, and now remove it.
    • Cut two identical pieces of line (the edge of the line should be cut at an angle. This will make the job easier). Take one of them and insert the end of the line into a special on the reel (there may be hooks, ears, clips). Then wind the string in the direction of the arrows. Distribute the line evenly, tightly. Attach the end of the string to the specially provided hole in the reel.
    • Do the same for the second part of the line, only the end Thread on the spool from the opposite side.
    • Return the line spool to the mowing head. Pull out the ends of the line through the holes in the spool and thread them into the special connector of the head.
    • Spread out the fishing line gently and close the lid. Cut off excess fishing line, leaving 12-15 cm. Each edge.

    Everything is ready. The trimmer refills the line and is ready to go. Now you can happily walk along the slopes of your favorite meadow, summer cottage, local area.

    It is only important to remember that not only the quality of the work performed, but also your safety will depend on how you load the cutting line into the trimmer.

    Instructions for refueling the line Trimmer (lawn mowers)

    We will learn how to properly tuck the line into the trimmer

    But beginners rarely know even the most basic rules of caring for this technique. So, the most common question is how to properly tuck the line into the trimmer.

    Trimmer head modification

    Trimmer mowing heads can be of various modifications: single-line for trimming the lawn (mows with one line of line), two-line for mowing grass and Land clearing with automatic line feed or manual line length adjustment.

    Modern growers are increasingly offering gardeners universal trimmers with two-line automatic mowing heads.

    Line Threading Instructions Trimmer

    Line selection

    In order for the trimmer to work “like a clock”, it is necessary to choose the right line, that is, choose it taking into account the trimmer model and type of work. There are two fundamental parameters in this matter. This is the diameter and section.

    The diameter of the fishing line must correspond to the one recommended for this model (it must be specified in the product passport).
    The cross-section of the fishing line is round, square, with sharp edges (pentahedron). A round line is designed for mowing young grass and lawn, square and pentagonal line will come in handy if the grass is hardened and weeds have grown on the lawn.

    Brief introduction

    To begin with, it must be said that knives or fishing line can be used as a cutting element in trimmers. Both types have their advantages and disadvantages.

    So, knives do a much better job with shrubs and dry wheatgrass, but polymer thread is much cheaper and more affordable. In addition, the 4 mm trimmer line also allows you to cut fairly tough grass. Of course, you cannot compare with a knife, but the efficiency is also not bad.

    Note that even in the latter case, you need to know exactly what its diameter is used in your trimmer. Manufacturers do not take all the values ​​from the ceiling: if you take a larger fishing line, then the engine is heavily overloaded, which may well cause the latter to fail.

    Brief introduction

    To begin with, it must be said that knives or fishing line can be used as a cutting element in trimmers. Both types have their advantages and disadvantages.

    So, knives do a much better job with shrubs and dry wheatgrass, but polymer thread is much cheaper and more affordable. In addition, the 4 mm trimmer line also allows you to cut fairly tough grass. Of course, you cannot compare with a knife, but the efficiency is also not bad.

    Note that even in the latter case, you need to know exactly what its diameter is used in your trimmer. Manufacturers do not take all the values ​​from the ceiling: if you take a larger fishing line, then the engine is heavily overloaded, which may well cause the latter to fail.

    How to properly install the line on your lawn mower

    DO NOT do this!

    Among our kulibins, there is a widespread opinion: before properly tucking the line into the trimmer, you need to change it to something more effective. Cable, for example

    Do not speak already in the monstrous load on the engine, breaking the cable can lead to serious consequences for your limbs. It is better to use the Recommended Consumables than the gender of the surgeon’s patient.

    If you really need to mow lawns that are heavily overgrown, then manufacturers offer special consumables with an increased surface area. In this case, the thinner fishing line is braided into a kind of pigtail. Maintains normal thickness but improves efficiency.

    Line selection

    In order for the trimmer to work “like a clock”, it is necessary to choose the right line, that is, choose it taking into account the trimmer model and type of work. There are two fundamental parameters in this matter. This is the diameter and section.

    The diameter of the fishing line must correspond to the one recommended for this model (it must be specified in the product passport).
    The cross-section of the fishing line is round, square, with sharp edges (pentahedron). A round line is designed for mowing young grass and lawn, square and pentagonal line will come in handy if the grass is hardened and weeds have grown on the lawn.

    We will learn how to properly tuck the line into the trimmer

    But beginners rarely know even the most basic rules of caring for this technique. So, the most common question is how to properly tuck the line into the trimmer.

    Line Threading Instructions Trimmer

    Getting started

    Then the remaining end of the line is threaded through the hole in the protective cover. After that, the reel and its protective cover are connected, and this time a piece of fishing line is threaded into the hole on the protective cover.

    The assembly is pushed onto the trimmer by turning clockwise until a clearly audible click is heard. By the way, before installing the line on the trimmer, figure it out better with its design. Otherwise, you can easily break something.

    That’s all. The tool is put into working position, turned on, after which the extra piece of fishing line is cut into a specially made blade for this purpose.

    So you learned how to properly tuck the line into the trimmer!

    Let’s get started

    Before you can properly tuck the line into the trimmer, you need to cut off the required amount. DO NOT be greedy, as for the first time and five meters is enough for training. To do this, the protective cover is removed from the trimmer coil, and one end of the fishing line is clamped in a special clamp (or slots).

    You need to rewind evenly, trying NOT to overtighten. In general, you need to fill the spool until the line layer is equal to the edge of the spool. It should not lie too tightly, slightly straightening after putting on the casing.

    How to remove the spool from the trimmer?

    So that the assembly process is not long and tedious, it is best to put the elements of the untwisted mechanism in order. It won’t let you get confused.

    Here are the steps for parsing:

    • The clutch nut is unscrewed.
    • Next, you need to untwist all the small washers and gears.
    • Need to remove the handle.
    • Need to disassemble the spool mechanism.
    • The rotor is removed
    • Now the line guide roller is disassembled.
    • Next, the coil is removed.

    How to wind the line on the trimmer reel (for beginners). Instructions on how to wind the line on the trimmer spool

    Here are the steps for winding a monofilament fishing whine on a trimmer spool:

    • The end of the line from the reel is pulled into the pass rings of the finished tackle.
    • Open line guide.
    • Using any fishing knot, tie one end of the monofilament to the bobbin.
    • Make a few turns by hand, move the spool wheel.
    • Now winding can be done with the handle.
    • When the winding is done, you need to close the line guide.

    In another method, bobbins with fishing line should be thrown over some kind of stick so that the bobbin rotates freely around its axis. The next step is to wind the trimmer bobbin. Here it will not be very convenient to wind a friend, it is better to resort to the help of a friend.

    As for winding the braid, the following steps must be taken:

    • Dip the prepared bobbins with braid into a container of warm water, or at least into the water of a river or lake, right on the spot.
    • Now you need to wind up. Due to the more or less softened fiber, the line will lie down and wind up quite evenly and tightly.

    What line is used for the trimmer?

    One of the types of fishing line is used to refuel the reel:. monofilament. It is a versatile single-thread fishing thread. The composition includes plastic compounds, polyethylene and everything like that.

    Whole factories are engaged in the manufacture of monofilament, which try to make the fishing line as efficient as possible each time, “able” to create the most approximate game of bait to live. Wicker. Two types of braids can be distinguished here: classic and braided cord in a sheath.

    Winding the line onto the trimmer reel. instructions

    Using this or that tool or device, sooner or later you have to change some of its components, refuel, and so on.

    For example, refueling the fishing tackle trimmer coil is quite simple, but there are some nuances that cannot be ignored. Here we need precise answers to the questions: how much and how?

    Threading the spools with thread of different types of bobbins

    It should be noted that there are several types of fishing tackle reels:

    • Inertial;
    • Inertia-free;
    • Multiplier.

    For each type of non-inertia reel, its own diameter is intended. Fishing whine. If the thread is thicker, it will NOT be possible to thread it into the spool. Difficulties will also arise if, for example, a too thin monofilament is used, and not one or another spool intended for refueling.

    In the case of threading a non-inertia spool, one of two well-known methods is used:. “cross-to-cross”. parallel winding, that is, thread after thread lies parallel to each other.

    Now in the multiplier bobbins. Multiplier spools are subspecies of inertial ones. Many fishermen make the same mistake, they tie the end of the string to the farthest hole of this element. It is wrong to do this, it is worth tying only for closely located holes.

    Filling the Fishing reel with a bobbin thread is done as follows:

    • First monofilament is fixed to the spool body.
    • Next, you need to attach the coil to the spinning rod and pass the free end of the scaffold through the right ring.
    • Tighten the device that protects the tackle from jerking fish.
    • Tighten axle brake.
    • Now you can wind up by guiding the line and, thus, controlling it.

    Tips from experienced fishermen

    Here’s what professional fishermen advise:

    • DO NOT wind too much line. This suggests that if the permissible winding length is 100 meters, then in this case you need to wind a little less. This will allow the device to work more correctly.
    • When winding, the string should NOT be too tight or, conversely, loose. And in that, in another case, it will NOT fit as it should. It can twist, go to the side, overlap, and so on. Conical layers of fishing line can also form, that is, thickenings on one side or another.
    • The winding should be carried out not reaching the upper edge of the coil, about 1-2 mm, this distance may increase slightly.
    • If the line is dropped periodically during winding, then you need to take a little more than the previous distance from the side wall of the spool to the line being wound. You need to increase literally by 0.5 mm.
    • Quickly winding the line will NOT distribute it well over the spool surface. On the contrary, it may “twist” so that it will be difficult to fix it. The best option is average speed.

    There are also devices that allow you to attach the spools directly to the rod. This allows you to wind the line, firstly, without assistance, and secondly, the refueling process is greatly simplified.