How to put line on a lawn mower

How to wind the line on a lawn mower

Head with two flutes

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. Having reeled the fishing line, we leave a small piece of it unwound in order to expose it outside. We fix this piece in a special groove located on the inner part of the reel and designed so that the line does not unwind at the time of collecting the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. A reel with one groove should have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, fix the resulting ends in special grooves, and if they are not there, we hold them with our fingers. We pass both ends into the existing holes on the outer casing of the coil. We collect the coil and attach it to the trimmer.

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the bend into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also reels in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, without winding, are threaded completely through the holes on the outer body of the reel, collect the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Rotate the button. the fishing line itself is wound inside. At the same time, it will not work to turn it in the “wrong” direction, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!

Automatic line winding on a spool

There is a type of reel in which the automatic mechanism winds on its own. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. In such a spool, it is impossible to make the winding wrong: the mechanism itself will determine the correct direction, since it can only turn in one direction.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden tools, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

We carry out the winding of the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Single-barbed trimmer spool

Single-barb lawn mowers reel

Many owners and specialists note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.

After winding, you need to leave a free end of 15-30 cm to increase the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

In the version with two grooves

The line is first folded in half to determine where the middle of the fold is.

Next, the loop formed at the bend is threaded into the groove that is formed between the two grooves.

After that, you can wind both bars of the fishing line in a separate groove.

You can fix the mustache and assemble the coil completely in the same way as already described above.

Opening a reel for the first time and winding a new line is not always easy. Over time, this procedure becomes almost automatic and will not take much time. Some reels have an automatic system that spins the line by itself. As a result, it remains only to correctly set the end of the line, and you’re done. In such models, the string must be put in the hole that is on the outside of the body. Next, the bobbin is assembled, and when the winding rotates, the fishing line is put on it.

The convenience of such reels is that it is impossible to wind up incorrectly, since the line will always turn only in the right direction.

How to choose the right line?

Nylon lines are suitable for both electric and gas powered trimmers. This consumable can be used for both hand tools and a wheeled lawnmower. It is important to choose the right line, as this directly affects both the result of the work and the service life of the unit. Of course, it is very easy to get confused in the offered assortment of lines, especially for beginners. However, there is a lot of advice from experts and those who have already tried various options.

For an electric trimmer less than 500 W, a thin line with a diameter of 1 to 1.6 mm is suitable. She will perfectly mow lawns with low grass. If the power of the tool is in the range from 0.5 to 1 kW, then it is better to give preference to a line with a diameter of 2 mm or slightly more.

This will be enough to cut thin grass or overgrown weeds, but not too thick.

For petrol trimmers and lawn mowers, line less than 3 mm must not be taken. This thickness will allow you to easily cope with any weeds, dry stems, dense grass. Diameter over 4 mm is only suitable for high power lawn mowers. It turns out that thick line is necessary for powerful technique. It is not recommended for use with low power trimmers, otherwise it will work poorly, constantly winding around the reel and creating additional load on the engine.

Typically, a standard package contains up to 15 meters of line. However, to replace the string on a reel, a length of about 7 meters is sufficient. It also happens that the line is produced in bays of 250-500 meters. When choosing a string, it is imperative to specify the date when it was produced. Nylon that is too old can dry out and become too brittle. If this happens, then you can soak the fishing line for a couple of hours in water, but it will not be completely the same.

When choosing, an important parameter is the section of the string, which can be of several types.

The round section is versatile. It is used for mowing grass of medium thickness and density. May make excessive noise during operation, but not used too quickly.

A square or polygonal section is more efficient than a round one. Sharp corners cut plant stems faster and with better quality.

Ribbed, twisted and star-shaped sections are the most effective. Such a fishing line manages to mow the grass very quickly. And its main drawback is its rapid wear.

The trimmer line is made of nylon, which is durable, lightweight, low cost and durable. To make the cost of the material even cheaper, polyethylene is added to it, but then the line overheats faster. Thick strings have a graphite or steel rod. Sometimes they are reinforced, which increases strength and service life.

It is worth noting that for two-piece strings are higher than for standard nylon strings.

How to reel?

Knowing how the reel is disassembled can speed up the line change process. It all depends on what design the coil has and how many antennae. Threading into a spool that has only one working mustache is quite easy, especially if you stick to a consistent plan.

Depending on the parameters of the reel and the length of the line set initially, it is recommended to choose a string from 2 to 5 meters.

First you need to remove the bobbin from the tool, and then open it.

One of the ends of the line must be installed in the hole inside the bobbin.

Next, the string should be wound onto the drum. over, this is done in the opposite direction from the normal rotation of the spool. Usually on the trimmers on the inside of the bobbin there is an arrow that shows in which direction to wind.

The Poor Man’s (FREE) Lawn Striping Kit

Part of the line must be pulled out and secured in a special groove located on the inside of the reel. Its purpose is to hold the winding while bringing the bobbin into working condition.

The end of the string must be passed through the hole located on the outer part of the bobbin.

At the last stage, you need to collect the parts of the bobbin and put it on the mower bar.

The installation of the line on a reel with two mustaches occurs in a slightly different way. First, you need to determine how many grooves go along the inside of the reel, on which the line is put on. There are options with one groove, and then both mustaches must be wound together. There are also models with two grooves, when each of the mustache goes separately.

For all double-whisker reels, a 2 to 3 meter string is recommended.

Which line to choose

Before you stock up on this material for refueling in the trimmer, you need to decide on the choice. After all, the usual so-called round fishing line is far from the only existing species. How to choose the most suitable one? First you need to determine the working conditions.

Selection by type. Round line is the most common. It will fit any coil with rare exceptions. This type of consumable is suitable for cutting fresh, juicy grass. But with the mowing of the so-called dead wood, such a species may no longer cope. It is pointless to mention attempts to mow bushes with this thread.

In addition to the usual type, there are others with sharp edges. Usually they are made with an asterisk or a square. The presence of sharp edges is the main feature and key difference of these threads.

It is due to this feature that threads of these types are able to mow dry weeds. But sharp-cut threads are not without drawbacks, the main of which can be called rapid wear and strength, which is noticeably inferior to the round type.

In addition to the already mentioned types of woods, there are also interesting and common varieties. Especially among them can be noted fishing lines, inside which a metal wire is stretched. This type of thread is often used in gasoline powered tools with an engine over 1.5 horsepower.

Metal-cored threads come in both round sections and sharp edges. Regardless of the type of section, such threads are the best suited for overcoming difficult-to-cut plants. Threads of this type can easily mow not only dry grass, but even small bushes.

The wires with a wire inside compare favorably with other types of consumables for their incredible wear resistance. Unfortunately, this feature has a more than noticeable impact on the price of this type. The cost of yarns with a core is much higher than the cost of other types of yarns.

Second winding method

• A previously prepared segment of six meters in length is required to be bent exactly in the middle and cut. Thus, two segments of the same length are obtained.
• At one end of each segment, you need to make a small “hook”. To do this, it is necessary to bend a couple of centimeters from the edge and fix it for a short time so that the “hook” does not unbend.
• Then one segment is taken. The hook is inserted into the through hole at the top of the bobbin.
• Now you can proceed to the key stage. winding. The direction in which to wind is indicated by an arrow on the bobbin. It is important to ensure that the line is wound strictly within the upper part of the reel. You do not need to wind the thread to the very tip. about fifteen centimeters should remain free from the end.
• In the upper edge of the spool there are small recesses (so-called grooves) for fixing the consumable. The loose “tail” of the thread must be inserted into one of these grooves.
• The top of the coil is tucked in. Now you need to do the same procedure with the bottom. Take the second piece of thread. The “hook” is threaded through the through hole at the bottom of the bobbin.
• After that, you can start winding the fishing line (within the lower compartment). And for this segment, you also need to leave about fifteen centimeters free from the end. This remaining “tail” must be inserted into the notch opposite to the one into which the end of the first segment was inserted.

The subsequent steps for this type of coils are exactly the same as described for the previous type in paragraphs five to nine.

This is how the line in the trimmer spool changes. There is nothing complicated in the process. And already after several refuelings, all actions will come to automatism.

To visually study the process described above, you can turn to the Internet for help. On the popular YouTube portal there are many different videos showing how to wind the line on the trimmer reel.

When spring comes, people often spend their free time at their summer cottage. They try to rid their area of ​​problems such as weeds and grass with the onset of warm days. It is difficult to do this manually, especially if the area is very large, so a lawn mower will help. Thanks to this technique, you can trim the grass and remove weeds. it is a suitable device for mowing unnecessary plants near the fence, at home, between rows in the garden on a flower bed, and so on. Read about how to choose the right mower for your needs here. The cutting element in this device is a fishing line (strong polyethylene thread), which is wound on a special element. a spool. But over time, the line wears out and it becomes necessary to replace it. The article will talk about how to fill the line in a lawn mower.

Line arrangement in the mower

The device of the element on which the nylon thread is wound is very simple. This element is called a coil. It has two “tracks”. the upper and the lower. Between these tracks there is a special partition with a recess. A fishing line is wound on these tracks. It must first be pulled through the recess.

In order to be able to pull out the coil without obstacles, it is necessary to unscrew the special button, which is located on the mower body.

Features of replacing fishing line on video.

The first way to wind the line

The required amount of line has been cut off. Now you need to carefully examine the bobbin in order to understand what type it belongs to. It depends on how the line is to be wound on it.

There are two types of bobbins. In general, they differ slightly from each other. Regardless of the type, the coil is divided into two sections. upper and lower. In the first type, the dividing edge does not close into a ring and has a depression.

In the second type, it is solid, but near it there are small through holes on the sides on both sides. The method of winding the thread must be studied depending on which of the above types the coil belongs to.

• The previously prepared six-meter segment must be bent in half. It is best not exactly in the middle, but in such a way that one half is about fifteen centimeters longer.
• Then the place of the fold must be inserted into the recess in the dividing face. One half of the line should be at the top of the spool, the other half at the bottom.
• Now you can start winding directly. You need to wind in the direction of the arrow on the bobbin. When winding, you need to hold the threads so that they do not intertwine and the upper half winds up in the upper part of the spool, and the lower half in the lower part. Each half should have about fifteen centimeters free from the end.
• There are small indentations (or, in other words, grooves) in the upper edge of the bobbin for securing the consumable. The ends of the threads must be inserted into these grooves so that they are fixed against each other.
• The final stage of threading the consumable into the tool. the ends attached to the bobbin must be threaded into the corresponding holes in the trimmer head.
• That’s all. The winding process is complete. Now all that remains is to assemble the head into a single whole. The spring fits neatly back between the bobbin and the head. Then you need to insert the bobbin into the head and press them together.
• It is recommended that the free ends of the thread be pulled out more. To do this, pull the ends of the consumable one by one so that they are removed from the grooves of the bobbin. You can make sure that the cutting element is removed from the retaining grooves by trying to pull the threads a little. they should freely exit through the holes in the head.
• While pressing the bobbin down, you need to put the cover over it. The cover must be screwed to the head so that all the grooves on their bodies are aligned and the bobbin remains fixed between them.
• And finally, the very last action. the head is screwed back into place at the bottom of the tool.

The process is complete. The line is tucked into a reel. The trimmer is ready for further work.

How to wind the line onto the trimmer spool

At first glance, threading a line into the reel of a tool is not an easy task. But it is enough to carefully study this process. and in the future, all the necessary actions will be performed without any difficulties.

It is worth reading this guide to find out how to tuck the line into the trimmer. The step-by-step instructions below take into account the peculiarities of the coils of different types of trimmers, therefore, it is applicable to any tool.

So, the procedure is as follows.

• The line spool is the bottom end of the trimmer. First of all, of course, you need to remove this head from the device. To do this, you need to fix the rod (or, in other words, the shaft) on which the coil is attached. It is required to fix it in such a way that it does not scroll. The easiest way to do this is by placing a kind of stupor (preferably metal) between the shaft threads through a special hole. When the shaft is fixed, the spool can be unscrewed.
• At this stage, you have to remove the bobbin from the head, on which the fishing line is attached. To do this, you need to disassemble the head into elements. To do this, you first need to find a retainer on its body. It is located on the circumference of the product and is like a button. When the latch is found, you need to press it firmly. Keeping the latch pressed, turn the head cover clockwise. Then you need to remove the cover and remove the bobbin.
• A tight spring is placed between the bobbin and the head. It needs to be put aside for a while so that it does not interfere with the winding process. Before proceeding with the step of winding the line, it is necessary to inspect the bobbin. If there are remnants of old fishing line on it, they must be removed. When the bobbin is cleaned, you can start preparing a new bobbin.
• From a previously prepared skein of new fishing line, it is necessary to measure and cut off six (maximum. seven) meters. Keep the bobbin close at hand.

At this point, the key stage actually begins, which this article is devoted to.

How to change the line on a lawn mower: detailed instructions

In 1971, American entrepreneur George Bollas invented a lawn mower that used a line as a cutting knife. Much time has passed since then, the drive has become more powerful, a modern trimmer can easily damage the bark, so the idea itself has transformed into mowing grass around obstacles without damaging the mower cutter itself. For a neat cut around obstacles, a smaller line head can be used and is easy to change when moving from large areas to delicate mowing. However, the cutting tool itself needs to be replaced periodically. We will tell you how to disassemble the head of a lawn mower (trimmer) and wind a new line.

All About Replacing the Line on the Trimmer Head

Choosing a line for the trimmer head

There are many types of heads available to suit different types of line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. over, its cross-section is round (including with a special groove to reduce the noise level), square, twisted and in the shape of a star.

There are no clear preferences, this explains the wide variety of shapes and diameters on the market. The round shape is usually stronger, but has the worst cutting ability and also produces a characteristic sound when rotated. Therefore, sometimes an acoustic groove is made on it, however, the use of this fishing line makes sense only on battery trimmers, in cars with a gasoline engine and a network drive, the sound level of the drive itself practically drowns out the sound from the fishing line. The square has a good cutting ability, and despite the fact that such a line is less strong than a round line, on average it is consumed less. Square fishing line quite easily cuts off the growth of the same willow up to 1 cm in diameter. The star has the maximum number of cutting edges, mows the best and is consumed the fastest.

The next nuance when choosing is rigidity. The fact is that in the production of nylon, a modifier (often maleic anhydride) is added to it, which improves its strength and prevents tearing. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, a seemingly good line, which remained for the winter, unexpectedly behaves in a completely different way in the spring. it breaks, stops coming out of the reel normally. There is a recommendation to soak the fishing line in water before work, but I do not see much point in this, maleic anhydride interacts with water, but if it is not enough in nylon, then there will be nothing to interact with. Therefore, it makes no sense to stock up on fishing line for a long period of time, breaking or constantly breaking fishing line, which, moreover, does not want to leave the reel itself, can significantly complicate the work.

How to reel?

Knowing how the reel is disassembled can speed up the line change process. It all depends on what design the coil has and how many antennae. Threading into a spool that has only one working mustache is quite easy, especially if you stick to a consistent plan.

Depending on the parameters of the reel and the length of the line set initially, it is recommended to choose a string from 2 to 5 meters.

First you need to remove the bobbin from the tool, and then open it.

One of the ends of the line must be installed in the hole inside the bobbin.

Next, the string should be wound onto the drum. over, this is done in the opposite direction from the normal rotation of the spool. Usually on the trimmers on the inside of the bobbin there is an arrow that shows in which direction to wind.

Part of the line must be pulled out and secured in a special groove located on the inside of the reel. Its purpose is to hold the winding while bringing the bobbin into working condition.

The end of the string must be passed through the hole located on the outer part of the bobbin.

At the last stage, you need to collect the parts of the bobbin and put it on the mower bar.

The installation of the line on a reel with two mustaches occurs in a slightly different way. First, you need to determine how many grooves go along the inside of the reel, on which the line is put on. There are options with one groove, and then both mustaches must be wound together. There are also models with two grooves, when each of the mustache goes separately.

For all double-whisker reels, a 2 to 3 meter string is recommended.

Lawnmower fishing line: how to choose and wind?

• How to choose the right line?
• Device in the mower
• How to reel?
• Safety engineering

With the arrival of spring, summer cottages are becoming the main residence of many of our compatriots. However, with the arrival of warm days, there is such a problem as fast-growing grass. It is inconvenient to constantly mow it with a hand scythe, and not all types of grass lend themselves to this old working tool. It is much more convenient to use modern lawn mowers for these purposes. Particularly popular among them are devices with a fishing line, which is easy to change if necessary.

In the version with two grooves

The line is first folded in half to determine where the middle of the fold is.

Next, the loop formed at the bend is threaded into the groove that is formed between the two grooves.

After that, you can wind both bars of the fishing line in a separate groove.

You can fix the mustache and assemble the coil completely in the same way as already described above.

Opening a reel for the first time and winding a new line is not always easy. Over time, this procedure becomes almost automatic and will not take much time. Some reels have an automatic system that spins the line by itself. As a result, it remains only to correctly set the end of the line, and you’re done. In such models, the string must be put in the hole that is on the outside of the body. Next, the bobbin is assembled, and when the winding rotates, the fishing line is put on it.

The convenience of such reels is that it is impossible to wind up incorrectly, since the line will always turn only in the right direction.

How to choose the right line?

Nylon lines are suitable for both electric and gas powered trimmers. This consumable can be used for both hand tools and a wheeled lawnmower. It is important to choose the right line, as this directly affects both the result of the work and the service life of the unit. Of course, it is very easy to get confused in the offered assortment of lines, especially for beginners. However, there is a lot of advice from experts and those who have already tried various options.

For an electric trimmer less than 500 W, a thin line with a diameter of 1 to 1.6 mm is suitable. She will perfectly mow lawns with low grass. If the power of the tool is in the range from 0.5 to 1 kW, then it is better to give preference to a line with a diameter of 2 mm or slightly more.

This will be enough to cut thin grass or overgrown weeds, but not too thick.

For petrol trimmers and lawn mowers, line less than 3 mm must not be taken. This thickness will allow you to easily cope with any weeds, dry stems, dense grass. Diameter over 4 mm is only suitable for high power lawn mowers. It turns out that thick line is necessary for powerful technique. It is not recommended for use with low power trimmers, otherwise it will work poorly, constantly winding around the reel and creating additional load on the engine.

Typically, a standard package contains up to 15 meters of line. However, to replace the string on a reel, a length of about 7 meters is sufficient. It also happens that the line is produced in bays of 250-500 meters. When choosing a string, it is imperative to specify the date when it was produced. Nylon that is too old can dry out and become too brittle. If this happens, then you can soak the fishing line for a couple of hours in water, but it will not be completely the same.

When choosing, an important parameter is the section of the string, which can be of several types.

The round section is versatile. It is used for mowing grass of medium thickness and density. May make excessive noise during operation, but not used too quickly.

A square or polygonal section is more efficient than a round one. Sharp corners cut plant stems faster and with better quality.

Ribbed, twisted and star-shaped sections are the most effective. Such a fishing line manages to mow the grass very quickly. And its main drawback is its rapid wear.

The trimmer line is made of nylon, which is durable, lightweight, low cost and durable. To make the cost of the material even cheaper, polyethylene is added to it, but then the line overheats faster. Thick strings have a graphite or steel rod. Sometimes they are reinforced, which increases strength and service life.

It is worth noting that for two-piece strings are higher than for standard nylon strings.

Device in the mower

In the trimmer, the element on which the string is pulled is very simple. It is called the “coil”. Usually it consists of an upper and a lower part (grooves), between which there is a partition with a recess. It is on these grooves that the fishing line should be wound. However, first it is pulled through the recess.

Before removing the coil, unscrew the special button located directly on the mower body. Remove the reel from the mower before changing the line.

It is not difficult to do this, but there are some peculiarities depending on the trimmer configuration and the coil itself.

In small electronic mowers, the motor and reel are at the bottom, and buttons are located on the sides of the reel. If you press them, you get the upper groove of the reel and the part where you need to wind the fishing line.

In bent-arm mowers that do not have a knife, the reels have special two-horned nuts. In such tools, you must hold the bobbin so that it does not move, and at the same time turn the nut clockwise. It is she who holds the entire reel, which is then easy to remove.

Straight boom mowers that can be fitted with a blade have a hole just below the reel. To remove the coil, a screwdriver is inserted into this hole, while the bobbin is fixed. After that, you need to turn the coil clockwise and remove it from the unit.

Sometimes there may be latches on the coil in the form of latches. They must be pressed to separate the parts of the coil. It is also possible that the top and bottom of the bobbin are connected by a thread. In this case, it is enough to grasp the top and bottom with your hands, and then twist in different directions until they unscrew.

In single flute model

The line must be pulled into the hole, and its mustache must be folded together and aligned.

Then winding is performed in the opposite direction to the rotation of the bobbin on the mower. Often there is an arrow inside the spool indicating how to put the line on correctly.

The ends of the string are fixed in special grooves or simply temporarily held by hands and pulled into the hole located on the outside of the bobbin.

After that, the spool is closed and attached to the rod, after which the mower is ready to work.

Safety engineering

Following safety precautions will allow you to quickly and safely insert new line into the spool on the mower. It is imperative that before the replacement begins and the coil is removed, the device must be turned off, especially for electric lawn mowers. It is important to constantly remind yourself to press the special lock button. On each mower, it can be located in different places, but this must be indicated in the instruction manual.

Remember to adjust the cutting element. Otherwise, the work will be unstable and of poor quality. Most often, there is a button on the unit itself that allows you to configure this. If nothing happens when you press it, or the string has loosened its tension, then you need to hold down the button and forcefully pull the fishing line out of the reel.

Winding the line is a very demanding process. It is important to follow all the steps correctly in order to tighten the line well. Materials other than special nylon strings should not be used. It is worth remembering that you cannot put a metal wire, a rod or an iron cable instead of a fishing line. This is dangerous, as the rig can very easily cut through the shoes even of coarse material and injure the wearer. Before putting on a new line, it is important to carefully read the operating instructions for the device, since some models of lawn mowers may have their own structural features, which are important to take into account when replacing.