How To Put The Line On The Trimmer Correctly

Table of Contents:

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Trimmer head with two tendrils

Double flute head

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). In principle, there is no difference between bobbins with one and two grooves, but with careless threading into the paired groove, there will be operational problems. Due to the likelihood of interlacing the adjacent line of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction of rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, the free ends (15-30 cm) are threaded into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do NOT worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off excess.

Winding the line to the trimmer

Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to winding the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

  • Trimmer head with one working Mustache;
  • Bobbin with two tendril fishing lines;
  • Auto winding reel.

Preparing to wind the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

    Compact Electric Trimmers.

Straight bar trimmer

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily unscrewed by hand clockwise.

Single Barbed Trimmer Spool

Reel for single-barb lawn mowers

Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of the trimmer reel movement.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. Passing the left end through the working hole of the coil and assembling the head.

Trimmer head with automatic line threading

Types of trimmer heads

Some models on the market are fitted with a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic trimmer head include the ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

How to wind the line onto the trimmer spool

The trimmer is a great solution for those who have a large garden or lawn near the house, which needs to be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, it will become necessary to replace certain elements, and this will have to be learned.

How can this be done? To replace the main cutter, you must first select it correctly. In principle, the lawn mower instruction manual should indicate the diameter of the thread to be used in it.

When you have acquired the required cutting element, try to install it correctly. It should be noted that there are a huge number on the Internet. Which will help you figure out how to properly thread the line into the trimmer spool.

How to change line to trimmer

Below we have provided Step-by-step instructions for replacing a whine trimmer.

The first thing to do is unplug the tool and turn off the engine. Then you need to remove the trimmer head. This can be done by using a simple screwdriver, lowered it into the hole of the gearbox to prevent the shaft from turning. And then just Unscrew

They are usually unscrewed in a clockwise direction, but different models have different mechanisms, so it may be necessary to twist in the opposite direction. But if suddenly, for some reason, you cannot figure it out, then we strongly recommend that you refer to the user manual to understand how to disconnect it

Second. After removing the mowing head, open it. This can be done by means of clamps, which are located opposite each other. Pressing on them, you can remove the head cover, and then pull out the spool on which the fishing line is wound. By pulling it out, you can determine what type it belongs to. There are bobbins one-piece and two-piece

We analyze how to thread the line into the trimmer spool in two versions

So, option one. load the fishing line into a single-section reel. The prepared piece of thread is folded in half and pushed into the spool. Then, we begin to wind both ends in the same direction, which will be indicated by the arrow on the spool. At the end of the winding, do not forget to check that the different ends of the thread are looking in different directions.

Option two. winding the line with a two-piece reel. The pre-prepared thread is divided into two parts, and its ends, must be fixed: this must be done by placing them in special fasteners

Winding is carried out, as in the first case, along the arrow indicated on the spool. Both segments must be wound so that they do NOT overlap. Further, the ends of the thread must be fixed in the grooves and spread on opposite sides.

The spring is then inserted into the reel and the whole thing is placed in the mowing head. When placing the coil in the trimmer you need to gently hold the spring parallel to insert the line into the cut of the mower head. And in the end, it just needs to be secured with the final part, that is, with a lid.

After threading the trimmer, you need to check it. If you did everything correctly, everything will work, but if you make a mistake, we recommend that you read the article again, or even better, if you look at how to install the line on the reel in the trimmers.

How to remove the line from the trimmer spool

Over time, the cutting element of the head wears out, and it becomes necessary to pull out the remnants of the old line. But not everyone knows how to do it. Our step-by-step instructions plus how to pull the thread from the trimmer spool, which you can find on the net, will help in solving this issue.

The mowing head must be disassembled

Remove the cover using the clips

Cleaning up the remnants of cutting material

Complicated? Of course not. But if, nevertheless, doubts creep into you that for some reason you will NOT be able to do this, then of course find and see how to pull out or how to wind the thread onto the spool of the lawn mowers.

How to replace the line with an electric trimmer

In fact, it makes no difference which oblique you use, be it electric or gasoline. Threading is the same. The only difference is that if you use a gasoline scythe, you get more freedom, since it is NOT limited by the cable, which is present on the electric scythe

Yes, do not hesitate to use special rollers for installing or threading the line in an electric scythe, which can teach you much faster than simple reading.

How to change line to trimmer

Below we have provided Step-by-step instructions for replacing a whine trimmer.

The first thing to do is unplug the tool and turn off the engine. Then you need to remove the trimmer head. This can be done by using a simple screwdriver, lowered it into the hole of the gearbox to prevent the shaft from turning. And then just Unscrew

READ  Petrol Trimmer Malfunction

They are usually unscrewed in a clockwise direction, but different models have different mechanisms, so it may be necessary to twist in the opposite direction. But if suddenly, for some reason, you cannot figure it out, then we strongly recommend that you refer to the user manual to understand how to disconnect it

Second. After removing the mowing head, open it. This can be done by means of clamps, which are located opposite each other. Pressing on them, you can remove the head cover, and then pull out the spool on which the fishing line is wound. By pulling it out, you can determine what type it belongs to. There are bobbins one-piece and two-piece

We analyze how to thread the line into the trimmer spool in two versions

So, option one. load the fishing line into a single-section reel. The prepared piece of thread is folded in half and pushed into the spool. Then, we begin to wind both ends in the same direction, which will be indicated by the arrow on the spool. At the end of the winding, do not forget to check that the different ends of the thread are looking in different directions.

Option two. winding the line with a two-piece reel. The pre-prepared thread is divided into two parts, and its ends, must be fixed: this must be done by placing them in special fasteners

Winding is carried out, as in the first case, along the arrow indicated on the spool. Both segments must be wound so that they do NOT overlap. Further, the ends of the thread must be fixed in the grooves and spread on opposite sides.

The spring is then inserted into the reel and the whole thing is placed in the mowing head. When placing the coil in the trimmer you need to gently hold the spring parallel to insert the line into the cut of the mower head. And in the end, it just needs to be secured with the final part, that is, with a lid.

After threading the trimmer, you need to check it. If you did everything correctly, everything will work, but if you make a mistake, we recommend that you read the article again, or even better, if you look at how to install the line on the reel in the trimmers.

How to remove the line from the trimmer spool

Over time, the cutting element of the head wears out, and it becomes necessary to pull out the remnants of the old line. But not everyone knows how to do it. Our step-by-step instructions plus how to pull the thread from the trimmer spool, which you can find on the net, will help in solving this issue.

The mowing head must be disassembled

Remove the cover using the clips

Cleaning up the remnants of cutting material

Complicated? Of course not. But if, nevertheless, doubts creep into you that for some reason you will NOT be able to do this, then of course find and see how to pull out or how to wind the thread onto the spool of the lawn mowers.

How to wind the line onto the trimmer spool

05 July 2018

The trimmer is a great solution for those who have a large garden or lawn near the house, which needs to be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, it will become necessary to replace certain elements, and this will have to be learned.

How can this be done? To replace the main cutter, you must first select it correctly. In principle, the lawn mower instruction manual should indicate the diameter of the thread to be used in it.

When you have acquired the required cutting element, try to install it correctly. It should be noted that there are a huge number on the Internet. Which will help you figure out how to properly thread the line into the trimmer spool.

How to replace the line with an electric trimmer

In fact, it makes no difference which oblique you use, be it electric or gasoline. Threading is the same. The only difference is that if you use a gasoline scythe, you get more freedom, since it is NOT limited by the cable, which is present on the electric scythe

How To Put The Line On The Trimmer Correctly

Yes, do not hesitate to use special rollers for installing or threading the line in an electric scythe, which can teach you much faster than simple reading.

Briefly about the line

Taking into account the models of the tool, the thickness of the line is 1.2-4 mm. There are such configurations:

  • Round is the most durable;
  • Curly. for soft grass;
  • Twisted or notched. for thin grass;
  • Professional, NOT suitable for all instrument models.

When changing the cutting thread, you need to choose the one that suits your trimmer type. Preference should be given to Specialized. Before tucking the line into the trimmer spool, it is best to soak it in water for half an hour. Then it will become more elastic and stronger.

How to fill the line in the trimmer so that working with it does not get tired

Many summer residents use a trimmer to combat weeds. a scythe with an electric or gasoline engine. It is convenient when working in hard-to-reach places for a lawn mower: in fences, flower beds, houses, in a garden on narrow aisles, and can cut small branches. The main element of this miracle technique is an ordinary line wound on a reel. The device is simple, but the cutting part wears out quickly and requires replacement. And the question of how to fill the line in the trimmer worries many owners of summer cottages.

How to put on the trimmer correctly

What types of woods are there

The most common type of line, which fits almost all types of reels # 8212; round cord. This is an ordinary fishing line, suitable for cutting succulent grass, but it will be much more difficult to mow dead wood with it, and even more so it will not cope with shrubs.

As a rule, the diameter, which can mow young grass, and does not exceed 1.6 mm. The thicker the thread, the more coarse grass it can overcome.

Important! When choosing a trimmer line, you must follow the instructions for your tool, since a thin thread will increase the wear of the torque mechanism, and a thick thread will overload the engine.

There are fishing lines with sharp edges in the form of an asterisk or a square, this option is more adapted to mowing dry grass precisely due to the existing sharp edges, but its disadvantage is greater wear and tear and it is inferior in strength to round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but it is used only for lawn mowers, since the exit of such a thread from the reel is difficult, it is used most often with discs in which the segments are inserted. The disadvantage of such a product is its fragility.

Most often in gasoline trimmers with an engine power of more than 1.5 HP. Use cords with a metal cable inside. This thread is ideal for cutting dry grass and small bushes. The presence of a core has a positive effect on the wear resistance of this material. The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

How to change the line to the trimmer and which one is better to choose

Since we discussed the choice of trimmer in the previous article. Today we will tell you how to properly fill the trimmer with fishing line, and which one is better to choose Based on the working conditions.

After you bought a trimmer and began to actively use it, sooner or later the question of replacing the fishing line will arise, since this is the most wearing out element in the tool, intensive use of the trimmer will lead to frequent replacement of consumables.

How to mow with a lawn mower?

The private owner wrote.
Excuse me, who is this who is meant by professionals ?

Professionals without quotation marks mean people who have undergone training and competently operate equipment.

Summer resident I wrote.
It is necessary to release gas only when moving from one mowing area to another. No need for mowing, why does the engine need to change loads?

The private owner wrote.
The need to change the speed with the trimmer movements. What for?

At one time, there was a detailed answer to these questions from Husqvarna:

1) Gas discharge is useful, firstly, due to the fact that the engine is slightly cooled, and secondly, the cylinder-piston group is lubricated better (this is especially true for disc mowing, since the disc continues to rotate and rotate the engine by inertia). The throttle valve closes, enriched fuel goes through the idle channel, and more oil gets to the parts of the cylinder-piston group.

2) Gas relief is necessary if you have an idle passage. For example, when folding grass into swaths: to the left. Mow, discard grass, throw off gas, drive to the right, increase throttle, start Mowing to the left.

3) In principle, you can never mow by dumping the gas (if there are no idle runs and the mower is constantly under load), but pay attention to the following things. A) the line may wear out, two short stubs will NOT give resistance to the engine, it will work at maximum speed and overheat; b) any engine can overheat if kept at maximum speed (Husqvarna designers did not set themselves the task of getting into the Guinness Book of Records for the maximum time before killing a lawn mower at maximum speed), so it is better to dump the gas.

Oleg_o wrote.
Mows with line and disc

What I quickly found on the Internet (for example, =.)), Drawn with fishing line. I have not seen anything about the disc.

Oleg_o wrote.
Spins at full power when reversing

Why just give full speed at any move? When you start to really work, you will clearly understand from the engine whether you need to add revolutions or not. Why do you need full turns when you have three blades of grass in front of you ?

Oleg_o wrote.
About variable loads, how unhelpful it is for the engine

Remember how 2T motorcycle engines work. They don’t always run at full speed. Nothing with a 2T engine from a change in speed will not.

Oleg_o wrote.
In the opposite direction, it seems to me not very convenient to mow. the grass flies in different directions

When you work with the line (that’s what I described), chopped pieces of grass fly in all directions (including on your pants and shoes) in any direction of travel. This is why the fishing line can be used to level the lawn well. If you have a disc formed by an elliptical fishing line passes at the same distance from the ground, then when you move Utin forward over the treated area, the line passes 2 or even 3 times. This allows you to remove steps and other flaws. No need to hurry.

How to quickly remove the coil from the tool

Before the thread is wound on a bobbin, it must be removed. over, the methods of removal depend on the characteristics of the instrument. On a trimmer with a motor in the very ground, the coil has two side buttons, when pressed, part of the body is separated along with the thread winding devices.

READ  What Oil Is Pouring Into The Patriot 555 Trimmer

On tools with a bent barbell, the lamb on the fixture is moved counterclockwise; having disconnected it, they remove both the bobbins and the spring inside it. On a trimmer with a straight bar, fix it with a screwdriver, rotate it clockwise and remove it. Then the device is disassembled either with the help of latches or by moving its parts in different directions. Take out the spring from the coil.

How to properly wind the line on the trimmer spool

Many, having worked out the factory line on the recently purchased trimmers, are trying to wind a new one, but they cannot, because they do not know how to properly wind the line on the spool (bobbin) of the trimmer. It seems that there is an instruction, but it still does not work. Let’s try in this article to deal with this issue.

So, in order to wind the line, you first need to remove the coil from the trimmer. this will be more convenient. The removal method will depend on the type of trimmer.

Removing the coil from the trimmer

On small electric trimmers with a bottom-mounted motor (when it is in the ground while working), the reels usually have two keys on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to grab the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the Trimmer Bar. Having unscrewed the lamb, carefully remove the entire coil, trying NOT to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver does NOT crawl even deeper and the coil will lock. Now steep the whole coil clockwise (since the thread is left-hand) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using snaps or a twisted lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection between the two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you also need to make sure that the spring inside is not lost.

than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a hole on the inside of the reel for the fixing line, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. I wound the fishing line, we leave a small piece of it unwound to put it out. We fix this piece in a specially groove located on the inner part of the reel and designed so that at the time of collecting the reel, the line does NOT unwind. If there is such a groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and threading the outer piece of fishing line into the existing hole, collect and put the coil back on the trimmer.

If the coil is designed to work with two tendrils, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. Reels with one groove should have a through hole through which the fishing line is threaded. We rewind 2-4 m of fishing line, threading it through this hole so that the fishing line sticks out equally on each side. And we simultaneously wind both tendrils of the fishing line in one direction, opposite to the direction of rotation of the coil to the trim tabs and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, the resulting ends We fix in the Special grooves, and if they are not there, we hold them with our fingers. Threading both ends into the existing holes on the outer casing of the coil. We collect the coil and fasten it to the trimmers.

If there are two grooves, fold a piece of fishing line 2-4 m long in half. Insert the loop obtained at the place of the fold into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also spools in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, and not winding, are threaded completely through the holes on the outer body of the reel, assemble the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Turning the button. the line itself is wound inside. In this case, twisting it in the “wrong” direction will NOT work, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!

How to properly wind the line on the trimmer spool?

Despite the fact that gardening equipment has been used for quite some time, it is still a novelty for some owners of private houses. That is why there are often questions about how to properly wind the line on an electric or gasoline trimmer.

This is essentially a simple operation, but all its stages must be performed correctly in order to achieve the desired result. over, in the operating instructions, only a few manufacturers provide an answer to this sore question. Explore the article and find out how the line winds around the trimmer reel.

The procedure for winding the line on the trimmer spool

First of all, you should know that trimmers have different working attachments. The reel can be designed for different lengths and thicknesses of the line. this point should be taken into account when purchasing consumables.

So how does the line load into the trimmer reel? All work is divided into several stages:

  • First you need to disassemble the trimmer head.
  • Unscrew the nozzle by rotating the drum to the right.
  • Press with your fingers on the two latches located on different sides of the tap holes and remove the top cover of the nozzle. You can pry off the cover with a screwdriver. This should be done carefully: reels with automatic line feed have a spring that can forcefully throw the cover along with all the contents of the reel.
  • Remove old line scraps.
  • Now you need to find the middle of the line. To do this, unwind it to the required length (for example, 10 m), cut and fold in half.
  • Hook the middle of the line into the existing groove or insert it into the hole specially designed for this. And start winding. The direction is indicated by the arrow, which is usually marked on the trimmer reel body (usually against the rotation of the drum). Some models have a double-sided reel: in this case, the line should be wound in different directions: one end in one direction, the other in the other, while the loop of the line must be inserted into the dividing slot in the middle.
  • Leave loose ends of the line about 20cm each. Later they will need to be fixed in the recess.
  • And finally, the last step will be the assembly of the drum. Reinstall the washers and spring. On the top ring of the reel there are two notches where you need to tuck the antennae of the fishing line. Thread them through the holes and place the spool in the drum, trying to tighten the line without displacing the spring.
  • Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, excess line will be cut off by the trimmer blade.

As you can see, winding the line on the trimmer reel is not difficult: the main thing is to do everything right. And here are some more tips that will come in handy when choosing a fishing line, winding it and subsequent work:

  • The line comes in a variety of thicknesses and cross-sections. The best option for winding is the “native” line for this model;
  • Never use fishing line or metal cables for the trimmer. This replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure Not only the lawnmower himself, but also those around him;
  • The line is cut when the trimmer is in contact with hard objects. Try not to allow this, otherwise you will have to stop each time, turn off the device and rewind the line on the reel;
  • Use regular line for cutting lawn grass and braid line for coarse weeds. It is more durable and will not constantly cut.

By size

Before threading the thread onto the trimmer spool, pay attention to its size. Most often used fishing line with a cross section of 2 mm.

You can choose a suitable diameter in the following ways:

  • See recommendations in the manufacturer’s instructions for trimmers.
  • Manufacturers often apply cross-sectional information to the bobbin.
  • The cross-section of the cord must match the diameter of the reel hole.

How to wind the line correctly: replacement features depending on the type of removable trimmer coil

To figure out how to tuck the line into the removable trimmer head, the following recommendations and instructions will help.

Auto feed trimmer: how to wind the line into the removable spool

Some models of trimmers have a reel, the threading of which is automatic. It is enough for the owner to fix the ends in the head, after turning on the equipment, the mechanism will perform all the winding manipulations on its own.

READ  How to Open the Huter Trimmer Coil Cover

How to wind the line correctly on the spool of the trimmer with one tendril

Most often, a thread up to five meters long is used. The procedure consists of the following steps:

  • Bent the cord with a loop and insert into the groove of the head.
  • Wind the thread in the direction opposite to the marks on the body. They indicate the direction of movement of the head.
  • Leave the end of the thread up to fifteen centimeters long to increase the centrifugal force.
  • Thread the free end through the spool outlet.
  • Assemble the trimmer head.

Things to consider when choosing a line

It is important to choose the right material before inserting and locking the line into the detachable trimmer spool.

Rating of the best petrol trimmer models. An overview of manufacturers and models, as well as useful tips from experts, considered in this review, will help in a difficult choice among many device models.

How to quickly and easily remove the coil with your own hands

Before replacing the old line with a new one in the detachable trimmer spool, you must remove the head.

The process is completely simple, even beginners can do the job:

  • Remove the upper fixing cover.
  • Remove the removable spool.
  • Get the spring out, if any.
  • Screwdriver Unscrew the bolt.
  • Remove the housing from the shaft.

By quality

Before you put the line on the trimmer, you need to Pay attention to the section of the cord:

  • Whining with a circular cross-section is the most common option. They cut the grass perfectly even in difficult areas;
  • Spiral line is suitable for thin grass. It is not very durable and is NOT suitable for old thickets;
  • A cord with notches and sharp edges is chosen for mowing weeds;
  • A fishing line with a variety of geometric sections will help mow the lawn more evenly, but the strength of the consumables is low.

The owner of the lawn mower should know that it is absolutely forbidden to use metal wire, fishing thread and various strings.

How to properly wind the line around the trimmer: Step-by-step guide and instructions

A beautiful lawn will only look truly well-groomed if you regularly mow the grass. A trimmer is best for tackling difficult areas. Any owner of the unit will sooner or later face a solution to the problem of how to wind the line on a reel, because wrong actions can not only worsen the quality of the mowing, but also disable the equipment. Today in the Homius review we will tell you about all the methods and nuances of replacing the fishing line and the features of choosing consumables.

How to wind the line on the detachable reel trimmer with two tendrils

You can see before work. And also take into account the following recommendations.

  • If there is only one track, both threads are wound parallel.
  • If there are two tracks, each piece is wound in a separate groove.
  • Wind the threads in the opposite direction to the rotation of the head.
  • The length of the risers does not have to exceed fifteen centimeters.
  • Thread the ends into the outlet holes.
  • Assemble the head and check the trimmer performance.

How to put on a belt

If the tool has a shoulder attachment, hang it on the shoulder before starting work. The trimmer is fixed to both shoulders if it has a knapsack mount.

The model with a bicycle handle is held by 2 hands, the D-shaped handle is wrapped in a palm. The belt must be worn so that it is comfortable, then the back will not get tired.

How to cut your lawn to keep it smooth

In order for the lawn to be cut evenly, the mower must be lowered as low as possible during operation. The plot must be divided into squares. You need to work, moving clockwise. In this case, the hay will always lie on the left, and not get in the way under your feet.

Running in

Before starting operation, be sure to run in gasoline mowers. The operator turns on the engine, it should run for a while at idle speed. Necessary Make sure that the engine does NOT overheat, the load does not have to be.

When running in lawn mowers, the load is gradually increased. If you start working at high speeds, the motor will not work well, this will affect the further operation of the mower.

When you start it for the first time, you should not completely use up the temporary resource. After the engine runs at idle speed, you can proceed to treating the lawn. the lawn mower must not run for more than 15 minutes, then the motor is turned off, it must cool down.

If you need to run the trimmer, the braid is first assembled. Then do Trial runs at least 3-5 times. If the engine is running well, proceed to mowing. At first they work NOT more than 5 minutes, then the duration of work is gradually increased.

First start

Before the first start-up, the operator assembles the mower, the procedure is described in the instructions that come with the product.

If the trimmer is gasoline, it must be checked before use. The fuel tank is filled up to the neck.

The engine must run in to fuel, so when first started it must run for a few minutes without load. Then start mowing the grass.

How to refuel the trimmer

gasoline-powered lawn mowers are available with two-stroke and four-stroke engines. The first option is much more common. What are the differences between them:

  • In trimmers with a 2-stroke engine, the response to pressing the engaging lever is faster (for this reason, lawn mowers are mainly equipped with this type of engine)
  • A tool with a two-stroke engine will be much lighter and also easier to maintain;
  • Fuel consumption in a two-stroke engine is higher than in a 4-stroke engine with the same power by about 30%;
  • 4-stroke engine is more environmentally friendly, since the fuel in it burns completely and is NOT emitted into the atmosphere, and its noise level is much lower;
  • And the most important distinguishing feature is the refueling: the 2-stroke engine is equipped with one common tank, into which gasoline mixed with oil is poured; 4-stroke has a separate gas tank and a tank for engine oil.

For refueling, you must use fresh AI-92 or AI-95 gasoline and high-quality motor oil for garden equipment (manufacturers produce different oils for 2- and 4-stroke engines). The oil can be mineral, semi-synthetic or synthetic.

The proportion of gasoline and oil for trimmers with 2-stroke engine can be found in the instruction manual for the particular model. Usually it is 50: 1, in some cases a ratio of 25: 1 or 40: 1 is recommended. Prepares the fuel mixture in a separate container with exact proportions. Never pour liquids “by eye” directly into the tank, and do not mix them first. Detailed instructions for mixing gasoline oil, with and a description, can be found on our website here.

Mowing tall grass

If it is necessary to cut the Tall grass, this is done in several passes. The lawn processes in 2-3 times. The rotating part is lowered from top to bottom, in this case the grass does not wind up on the reel.

The operator should be aware that grass wrapped around the reel will overheat the motor. If this happens, the mower is turned off and the coil is Cleaned.

Mows grass most effectively with the ends of the line, not the entire length. In the second case, the tool works worse, the motor may be overloaded. If you need to cut grass over a large area, tilt the trimmer towards the side to increase efficiency.

Principle of operation

If we consider the principle of the trimmer, then it is similar to a hand braid. The difference is that it is equipped with a motor, with its help the cutting element is rotated.

Manufacturing companies produce the following mower models:

  • On which a gasoline engine is installed. These garden tools have a fuel tank, this is their distinctive feature.
  • Devices with an electric motor. These tools are lighter because they have a fuel tank. But when choosing such models, you need to take into account that a power source is needed for their operation.

All electric streamers can be divided into those that run on batteries and models that are connected to the mains. Each type has its own characteristics, but they affect the power supply unit. If you do not take it into account, then the rest of the structure is similar in different devices.

If you take any trimmer model, then it consists of elements such as:

  • Motor;
  • Fuel tank (electric lawn mowers do not have one)
  • Levers used to control the mower;
  • Grass cutting knife;
  • Barbell;
  • A spool with a wound line, which is used for cutting grass;
  • Protective cover;
  • Bevel gear.

The motor is placed near the mowing head and can be mounted from below or from above. The reducer is available only in those models that have a straight bar. If it is bent, then the main bearing becomes the connecting element. It consists of 2 bushings.

The choice of the cutting element depends on how hard the grass must be mowed. Most often, a fishing line is used in the work, it is called a cord. There are products of various shapes on sale, among buyers in demand are spiral and round.

The fishing line is wound on a spool, it is inserted into the spool, while the 2 ends of the wire remain free. When the mower engine starts to work, the bobbin rotates, the grass is cut with the free ends of the line.

Oblique under hay

It is better to mow hay with a fishing line, and a metal disc. The grass is cut at the root, keeping its length as much as possible.

How to use the trimmer correctly

Garden trimmers are efficient. Newbies think it’s easy to operate a lawn mower by plugging it in or refueling, but that’s not entirely true.

The efficiency of the garden tool and its service life directly depend on the operating conditions. Therefore, before using the trimmer, you need to do some preparatory work.

The lawn from which it is necessary to mow the grass is carefully examined. Glass and large stones must be removed. When flying out from under a running mower, they can injure a person. The wire is removed from the lawn, because it can wrap around a rotating element, break the mower.

After that, proceed to the installation of the cutting system. On sale there are trimmers of low power, which use only line. It is designed for cutting juicy and soft grass. But there are models with a capacity of more than 1 kilowatt, on which metal knives are installed. They cut sow thistle and other hard weeds, trim young shrubs.

In order to replace the cord with knives, you need to Unscrew the fastening nut, install the cutting element. Then the nut must be returned to its place, tightened with a wrench.

The operator must take care of his own safety. It is necessary to mow the grass in tight protective clothing. Special goggles are used to protect the eyes; they are protected from dust, grass and flying debris. Hands are covered with gloves.

The electric trimmer is plugged into the network, and battery models are charged for several hours before use. Gasoline mower is filled with fuel.

Hold the mower so that the spool or knife is parallel to the ground. When the tool is in the correct position, turn on the motor. Turn off the mower after the grass has been cut.