How to Remove a Tank on a Huter Trimmer
Guides, Instructions, Forms
Huter Ggt-1000t trimmer instruction
Manual Lawnmower HUTER GGT-1000T
Huter ggt-1000t trimmer instruction:
Holux m-1000 instruction
Cutmaster 100 instruction
Trust pw-2100 manual
Vectra 100 manual
Malegra 100 manual
Whistler xtr-575 instruction
Siger u200 manual
Instructions for bypassing and inspecting electrical installations
Huter Gas Trimmer GGT-1000T
Huter Gas Trimmer GGT-1000T made in the form of a straight rod with an upper engine. It is designed to mow tall grass and trim the lawn where you cannot use a large lawn mower on wheels. next to bushes, trees, fences, on flower beds. This lawn mower is equipped with a two-stroke engine, air-cooled and electronically ignited, with a volume of 32.6 cubic centimeters. Its power is 1000 watts, a fuel tank with a capacity of 0.7 liters is used. This is enough for long-term work on mowing grass.
The gasoline engine of the Huter GGT-1000T trimmer is capable of idling to spin at a speed of 7500. 9500 rpm a knife or fishing line. This model uses a proprietary anti-vibration system, which makes it possible to mow grass for a long time.
Fuel that uses the trimmer sparingly is a mixture of AI-92 gasoline and two-stroke oil. The engine ignition is fully electronic, so the internal combustion engine is connected to the controls on the handle using an electric wire.
During operation, the operator holds the trimmer by the two rubberized ends of the bicycle control handle. It is located approximately in the middle of the bar, and can change its mounting location for the convenience of the user.
Mowing grass with the Huter GGT-1000T trimmer can be done using a fishing line or a cutting knife with a mowing tire of 255 mm. Also at the bottom is a strong protective casing. It is specially designed to prevent strong dispersion of parts of the grass, injuring the operator. The manufacturer recommends immediately after completion of work to clean the grass plaque of the open tool nodes. and then he will serve you for a long time.
Features of the trimmer Huter GGT-1000T
The convenient handle provides easy control and prevents slipping of the Huter GGT-1000T gasoline trimmer.
Advantages of Huter GGT-1000T
Trimmer Huter GGT-1000T
The Huter GGT-1000T gas trimmer is equipped with a two-piece bicycle handle that the operator can set in a convenient position. The air cooling system prevents overheating of the engine. Electronic ignition system simplifies engine starting. Anti-vibration system reduces noise and increases comfort. The shoulder strap evenly distributes the weight of the instrument throughout the body.
Fuel is a mixture of gasoline with an octane rating of at least 92 and two-stroke engine oil.
- Air-cooled two-stroke engine
- Electronic ignition;
- Gas trigger lock;
- Shoulder strap;
- Mowing is carried out using a fishing line and a knife;
- Protection against accidental inclusion;
- The handle consists of two parts;
- Anti-vibration system.
- Huter GGT-1000T Trimmer SpecificationsMain characteristics
Certified Product Yes
Cutting Width 25 cm
Noise level 96 dB
Overview gasoline lawn trimmers. YouTube
Shoulder strap, reel with fishing line, disc / knife
Engine type gasoline
Working volume 33 cc
Power 1.35 HP
Design Dimensions Huter GGT-1000T trimmer reviews
We will publish it on the site after checking by the moderator. This usually takes a couple of hours.
Petrov Ivan February 7, 2015Review from Yandex.Market
Advantages: Easy start, ample power
Disadvantages: Gluttonous, very poor belt, poor quality materials and workmanship
A comment: I bought this trimmer in 2011, I have been using it for 4 seasons, so I write competently. ) So, immediately after purchase: ALL fasteners that are not involved in the assembly before use, i.e. motor screws and so on, was tightened almost by hand. The fasteners, which had to be unscrewed for assembly, were tightened tight. Belt. This is a separate song. My leash for a dachshund is wider and stronger than a complete strap. Naturally, it was immediately replaced by a wide and durable. Reel with fishing line: it didn’t fly apart from me just because I didn’t have time. for the first season of work, her plastic sides rubbed to the holes! I had to buy a universal replacement, which has since been working quite normally. Starting the engine is easy and sure that it is cold, that is hot. This is the main advantage of the trimmer. But gasoline this unit eats with great pleasure. a full liter tank is enough for three hundred parts of a well-overgrown area or 4-5 hundred parts of sparse grass. My past trimmer spent exactly three times less fuel on these areas. The weight of the unit, in my opinion, is also too high for comfortable work, I would like a couple of kilograms less, the vibration during operation is quite strong. all fasteners have to be periodically tightened, loosened. After a long work, the hands on the handles from vibration hurt. Summary: reliable motor, shaft and gearbox. Disgusting quality of plastic and assembly. Heavier and gluttonous. In general, next time I won’t buy one. the priorities will be less weight and vibration when working.
Falileev Vladislav August 7, 2014Review from Yandex.Market
Advantages: 1. Price 1. Mows 2. Chops small bushes (with fishing line, milling cutter did not try)
Disadvantages: 1. Poor complete fishing line (immediately after the first entry into the grass I replaced it with another one (with an asterisk)) 2. The set contains a poor instruction that says that you need to start with a closed plug, but it starts very tight, you have to pull very sharply and quickly and many times, and it starts up two times with an open one 3. uncomfortable belt (changed to a homemade one) 4. the cable shirt is not reinforced, just fasten it on the bar and it will hang, sometimes gas sticks to me, I decided to change the cable (put the brake handle on the bike in place those with a cable) 5. The instructions do not say how to lubricate the gearbox
A comment: The normal model for such a price can be used for its intended purpose, the main thing is not to immediately throw it into the thick of grass, but to start smoothly from the edge AND MOST IMPORTANT: DO NOT TRUST THE ASSEMBLIES, BETTER COMPARE THAT YOU HAVE ASSEMBLED WITH THE INSTRUCTIONS, and pull all the bolts after purchase ( without fanaticism, you can break the thread)
The user hid his data July 9, 2013Review from Yandex.Market
Advantages: Powerful, when mowing, cuts even overgrowth of trees.
Trimmers. Buy electric or gasoline trimmer.
Trimmers. Wide selection trimmers and lawn mowers. Reviews. comparisons
Disadvantages: Immediately need to replace the coil, protective cover, belt. Bolts tightened tightly, barely unscrewed.
The user hid his data June 16, 2013Review from Yandex.Market
Advantages: Powerful, inexpensive, the presence of a knife in the kit.
Disadvantages: Fragile plastic and reel, uncomfortable belt, not a native gas torso.
A comment: First impressions were good, but then the coil broke, the belt lock broke, and the plastic on the engine cracked. The manufacturer saved too much on the little things, which spoiled the impression of the device. It justifies its price.
sergei-volkov83 September 6, 2012Review from Yandex.Market
Advantages: The best trimmer that I used (3 pieces have served for 7 years). It is very convenient to use, the drive from the kit does an excellent job with tall grass.
Disadvantages: works noisy, surprised.
A comment: in fact, to give special and complex trimmers is not necessary. For simplicity, lightness and a good scythe of grass. my plus!
The user hid his data June 1, 2012Review from Yandex.Market
We will publish it on the site after checking by the moderator. This usually takes a couple of hours.
B 250 B Lightweight lawn mower for working with grass and weeds. The package includes a trimmer head and a grass knife. 07/27/14 | notes | reblog
Reviews Huter GGT-1000T
Powerful, when mowing, cuts even overgrowth of trees.
Immediately need to replace the coil, protective cover, belt. Bolts tightened tightly, barely unscrewed.
Easy start, ample power
Gluttonous, very poor belt, poor quality materials and workmanship
I bought this trimmer in 2011, I have been using it for 4 seasons, so I write competently.
So, immediately after purchase: ALL fasteners that are not involved in the assembly before use, i.e. motor screws and so on, was tightened almost by hand. The fasteners, which had to be unscrewed for assembly, were tightened tight.
The belt is a separate song. My leash for a dachshund is wider and stronger than a complete strap. Naturally, it was immediately replaced by a wide and durable.
Reel with fishing line: it didn’t fly apart from me just because I didn’t have time. during the first season of work, its plastic sides rubbed into holes! I had to buy a universal replacement, which has since been working quite normally.
Starting the engine is easy and sure that it is cold, that is hot. This is the main advantage of the trimmer. But this unit eats gasoline with great pleasure. a full liter tank is enough for three hundred parts of a well-overgrown area or 4-5 hundred parts of sparse grass. My past trimmer spent exactly three times less fuel on these areas.
The weight of the unit, in my opinion, is also too high for comfortable work, I would like a couple of kilograms less, the vibration during operation is quite strong. all the fasteners have to be tightened periodically, loosened. After a long work, the hands on the handles from vibration hurt.
Summary: reliable motor, shaft and gearbox.
Disgusting quality of plastic and assembly.
Heavier and gluttonous.
In general, the next time I will not buy one. the priorities will be less weight and vibration during operation.
Video: How to Remove a Tank on a Huter Trimmer
Powerful, inexpensive, the presence of a knife in the kit.
Fragile plastic and reel, uncomfortable belt, not a native gas torso.
First impressions were good, but then the coil broke, the belt lock broke, and the plastic on the engine cracked. The manufacturer saved too much on the little things, which spoiled the impression of the device. It justifies its price.
The best trimmer that I used (3 pieces have served for 7 years). It is very convenient to use, the drive from the kit does an excellent job with tall grass.
works noisy, surprised.
in fact, to give special and complex trimmers is not necessary. For simplicity, lightness and a good scythe of grass. my plus!
2. Chopping small bushes (fishing line, milling cutter did not try)
1. Poor complete fishing line (immediately after the first entry into the grass, replaced with another (with an asterisk))
2. In the kit there is a miserable instruction that says that you need to wind up with a closed plug, but it starts up very tightly, you have to pull it very sharply and quickly and many times, and open two times
3. uncomfortable belt (changed to homemade)
4. the cable shirt is not reinforced, as fasten on the bar and it will hang, sometimes gas sticks in me, I decided to change the cable (I put the brake handle on the bicycle with the cable)
5. The instructions do not say how to lubricate the gearbox
A normal model for such a price can be used for its intended purpose, the main thing is not to immediately throw it into the thick of grass, but smoothly start from the edge
AND MOST IMPORTANT: DO NOT TRUST THE ASSEMBLIES, BETTER COMPARE THAT YOU HAVE ASSEMBLED WITH THE INSTRUCTIONS, and pull all the bolts after purchase (without fanaticism, you can break the threads)
Huter equipment: trimmer for the perfect garden
February 5, 2014
Many will agree that having your own home is a real pleasure. What could be better than after a hard day stretching out on the lawn and, squinting from the rays of the gentle sun, fall into a light nap! But in order to enjoy lying on the grass with pleasure, you must first bring the lawn in perfect condition. Even a small area dotted with emerald grass requires care. In the warm season, a lawn needs to be cut several times a month.
Garden equipment manufacturer
One of the manufacturers of quality equipment for gardens, lawns and planting is the German company Huter. Trimmers, lawn mowers, motor cultivators, chainsaws, high pressure washers and many other equipment comes out under this brand. The quality, reliability and durability of the products are verified by numerous experiments. A huge number of people recognize the fact that this organization offers an excellent assortment of garden equipment at surprisingly reasonable prices.
Put the lawn in order? Easy!
A device that is also produced by Huter, a trimmer for caring for the territory adjacent to the cottage, is in great demand among the population. This equipment can be powered either by electricity or by fuel. over, both types have their advantages and disadvantages. Consider a gasoline variant of the Huter technique. The fuel trimmer has a two stroke engine. Depending on the model, the volume of the engine can range from 25 to 43 cubic centimeters. The engine is equipped with an air cooling system, as well as electronic ignition. Its power, again, depends on the version of the model and can reach 1300 watts. A positive aspect is the presence of a system that allows you to conveniently and for a long time use the equipment without feeling vibration and jolts. Huter, whose trimmer is in great demand among buyers, took into account their wishes and minimized the weight of the equipment while maintaining other characteristics. So, the mass of gasoline equipment is 7 kg. However, this is a bit more when compared with her electric "brother." The fuel tank capacity of almost all models is 0.7 liters.
Huter GGT 1000t Petrol Trimmer
Comparison with electrical counterpart
Petrol Trimmer Huter Ggt-1000T Instruction for free
Description: The HUTER GGT.1000T gasoline trimmer with an integral rod is profitable in price and is equipped with a two-stroke engine top.
1 2 1. 2. 3. 4. 5. 6. 7. CONTENTS Introduction ……………………………………………………………………………………… 3 Safety regulations……………………………………………………. 3 Technical specifications …………………………………………………………… 4 Assembly ………………………………………………………………… ……………………. 5 Operating Instructions ……………………………………………………. ………….… 8 Maintenance …………………… …………………………………….9 Storage ……………………………………………………………………………………….11 INTRODUCTION Gas trimmers are manufactured according to the state of the art and current safety standards. To avoid accidents and to use the trimmer correctly, do not start work without thoroughly studying this manual. SAFETY INSTRUCTIONS 1. It is forbidden to use the trimmer to persons who are in a state of physical fatigue or under the influence of AL-KOgol, drugs and medicines. It is also not allowed to use the trimmer with children or untrained persons. 2. When working with the trimmer, use protective equipment (appropriate clothing, gloves or mittens, safety glasses, earphones, hard hat). 3. It is forbidden to use the trimmer near flammable and explosive substances, with a high level of humidity, during rain, and also at a distance of less than 15 meters from unauthorized persons. 4. It is strictly forbidden to use the trimmer with or without a damaged casing. Do not use a trimmer without a silencer. 5. It is strictly forbidden to install metal wire, knitting needles and other materials instead of fishing line, and also to use a cutting disc with mechanical damage. 6. Verify trimmer integrity before starting. The cutting disc must rotate freely. 7. When working, select the correct position, your unstable position can lead to serious injuries. 8. Do not leave the trimmer turned on unattended. 9. Do not remove the fuel tank cap while the engine is running. If fuel spills when filling the tank, be sure to wipe the fuel stains with a dry cloth and change the place before starting the engine. 10. Do not use fuel mixture to clean the trimmer. 11. Carry out any maintenance and replacement measures only with the trimmer turned off. 12. Monitor the condition of the trimmer. In the event of a failure, noise, vibration, knocking, sparks, flames, seizing or other signs of malfunction, immediately shut off the engine. 13. It is forbidden to make any changes in the design of the trimmer, violate the integrity of the case, try to open and repair the trimmer yourself. 14. It is forbidden to drop and throw the trimmer. 15. Mowing is permitted only during daylight hours or in high light. During prolonged mowing, take breaks. 3 ATTENTION! Exhaust fumes are toxic and hazardous to health. IT IS FORBIDDEN TO START THE PRODUCT ENGINE IN AN ENCLOSED OR BAD A ventilated room. GASOLINE AND ITS VAPORS ARE FLAMMABLE AND EXPLOSIVE! TECHNICAL CHARACTERISTICS Model Engine Ignition Type Volume, cm3 Power, W. Engine revolutions, rpm Anti-vibration system Bevel width, mm. Sound pressure level, dB Split bar GGT800T GGT800S GGT1000T GGT1000S GGT1300T GGT1300S 2-stroke, air-cooled Electronic 25.4 800 32.6 1000 7500-9500 Yes 255 96 42.7 1300 no yes no yes no yes 4 ASSEMBLY Trimmer device 1 2 3 4 5 6 7 8 9 10 11 12 Starter grip Starter Air flap control lever High-voltage wire cap Fuel tank cap Silencer Left handle Engine housing Fuel tank Right control handle Bottom of the crank mount Belt securing ring 13 14 15 16 17 18 19 20 21 22 23 24 Upper part of the shut-off handle mounting ignition trigger Gas trigger lock Gas trigger Gas trigger rod with shaft assembly Cutting knife Lower gear Protective cover Fishing line reel Shoulder strap Protective cover fastening strap 5 1. Rod. (for models GGT-800S, GGT-1000S, GGT-1300S) Squeeze the locking lever of the mounting system, and connect both parts of the boom. The locking lever mount must engage in the guide groove on the lower bar. A properly assembled connection cannot be opened without pressing the lock lever. Tighten the optional mounting of the coupler all the way. Depending on the work you are doing, you can rotate the lower bar at fixed angles of 90 and 180 degrees. In this case, the lower bar will always be securely fixed. 2. Control handle. For fastening the control handle to the rod, the control handle fastening unit is used. It consists of the upper part of the mount, mounting bolts, the lower and middle parts of the mount located on the bar. The procedure for installing the control handle on the boom. Take the middle part of the control handle mounting and place the right and left handles in the recess, at an equal distance from the center. Install the upper part of the mount in the slots in the slots located on the middle of the mount. Fasten the upper and middle parts of the mount using bolts. (fig. 2). NOTE. The handle consists of two parts to allow for separate adjustment. It is possible to adjust the position of the control handle along the bar to achieve optimal product balancing. To regulate the position of the control handle: loosen the lower mounting bolts with a hex wrench; move the lower part of the control handle mounting along the product rod to the required distance; tighten the bolts tightly. (fig. 3) fig. 2 6 fig. 3 Fig. 4 3. Installing the protective cover Join the holes in the protective cover with the holes in the mounting bracket. (Fig. 4) Fasten the protective cover to the bar with bolts and washers using an Allen key. 4. Installing the shoulder strap Attach the shoulder strap carabiner to the shoulder strap ring. To ensure better balancing of the product, adjust the position of the ring for attaching the shoulder strap to the product bar by loosening the ring fixing bolt first. After adjustment, fix the ring with the ring fixing bolt. Adjust, if necessary, the length of the shoulder strap to ensure comfortable working. 5. Installing the cutting knife Align the hole in the shaft hub with the hole in the gear cup. (Fig. 6) Insert the metal locking pin into the hole in the gear cup and into the hole in the shaft hub. Unscrew the fastening nut from the hub of the product. Remove the cup from the shaft, leaving the hub. (Fig. 7) Fig. 6 7 Fig. 7 Install the cutting knife on the hub. Make sure that the cutting knife is correctly centered and lies on the groove of the hub. Install the mounting cup on the shaft. Install (screw) the nut onto the shaft. Check that the knife is installed correctly. While holding the locking rod with one hand, securely tighten the nut with a pipe wrench (from the tool kit), turning it counterclockwise (from the output shaft side of the gearbox). (Fig. 8) Fig. 8. 8 WARNING: KEEP CUTTING KNIFE IN A PLACE OUT OF THE REACH OF CHILDREN! A WARNING. If the cutting knife is not correctly centered, strong vibration occurs during operation, as a result of which the cutting knife can fly to the side, causing injuries to the user or unauthorized persons. A WARNING. To avoid damage to the product and personal injury, the user must not start the engine with the locking rod inserted into the hole in the gearbox cup and into the hole in the shaft hub. 6. Installing the reel with fishing line Align the hole in the shaft hub with the hole in the gear cup. Insert the metal locking pin into the hole in the gear cup and into the hole in the shaft hub. Unscrew the fastening nut from the hub of the product. Remove the cup from the shaft, leaving the hub. (Fig. 7) While holding the rod, twist the coil counterclockwise until it stops. INSTRUCTIONS FOR USE Preparation of the fuel mixture The fuel mixture should be prepared from gasoline with an octane rating of at least 92 and special oil. You must use high quality oil designed for air-cooled two-stroke engines. The recommended proportional ratio of the prepared fuel mixture is on the label of the oil used. The use of oil intended for 2-stroke engines with water cooling (for boat motors) is prohibited. Trim Trigger WARNING. Before starting the engine, make sure that the working body of the product does not touch foreign objects. 1. Fill the fuel mixture into the fuel tank. 2. Five to seven times press the rubber cap for manual pumping of fuel to fill the carburetor with fuel mixture (Fig. 9). In this case, the pumped fuel mixture should be visible through the rubber cap of the manual fuel pump button. If the fuel mixture does not fill the cap, press the manual fuel pump button a few more times. 3. Move the choke lever up to the COLD START position (Fig. 10). 8 4. On the control handle, set the ignition to the ON position. 5. On the control handle, press the trigger and lock it. 6. Hold the trimmer with one hand, pull the starter handle with your free hand until it engages. Pull sharply until the engine is first started (Fig. 11). Fig. 9 Fig. 10 Fig. 11 WITHOUT PRELIMINARY EXTENSION OF THE STARTER CORD TO START THE ENGINE IS FORBIDDEN. STRONG PERFORMANCE OF THE UNLOADED CORD, EXTENSION OF THE CORD TO AN IMPACT CAN CAUSE THE BREAK OF THE STARTER MECHANISM. 7. Set the choke lever to the middle position (Fig. 12). 8. Pull the starter handle several times until the engine starts. Let the engine warm up for 5-10 seconds. 9. Move the choke lever down, then pull the trigger to unlock. 10. Gently pull the trigger, bring the engine to maximum speed and proceed to work (fig. 13). Mowing hold the trimmer firmly with both hands on the ergonomic handles. Fig. 12 Fig. 13 11. If the engine is warm, turn on the trimmer and follow the same procedures as for a cold start, but without pressing the pump. The air damper should be in the lower position. YOUR TRIMMER IS EQUIPPED WITH A SEMI-AUTOMATIC FISHING SYSTEM. DURING TRIMMER OPERATION AT MAXIMUM TURNOVER. Slightly PUMP THE TRIMMER REEL ON THE EARTH, THE LENGTH OF THE CUTTING LINE WILL INCREASE BY APPROXIMATELY BY 25 MILLIMETERS. 9 Stopping the trimmer 1. Release the throttle control lever. The engine should cool slightly while idling. 2. Turn the ignition switch in the direction of the arrow indicated on the control handle to the "STOP" position. A WARNING. After the fuel mixture is developed from the fuel tank, it is necessary to allow the engine to cool before the next refueling. After completion of work, unused fuel mixture may remain in the fuel tank. Be sure to drain it into the canister. It is not allowed to leave the fuel mixture in the trimmer tank for more than 12 hours. This can lead to unstable engine operation. MAINTENANCE 1. Air filter Clean or replace the foam element of the air filter every 10 hours of operation. The condition of the air filter is one of the basic conditions for reliable engine operation. Remove the air filter protection cover (Fig. 15). Pull out the air filter and rinse it thoroughly first in a soapy water solution, then in clean, warm water. Dry the filter at room temperature, soak it with 2-3 drops of engine oil before installing the filter (Fig. 16). Fig. 15 Fig. 16 2. Spark plug Check the condition of the spark plug regularly. Regularly clean the spark plug and check the gap between the electrodes. The clearance should be 0.5 mm 3. Cooling system If the cooling holes are contaminated with mowing products and oil sludge, use a brush and / or compressed air bottle to clean. Dirty ribs on the engine cylinder can cause it to overheat and break. Clean the cylinder fins regularly with a brush and / or compressed air. 4. Muffler Depending on the use of the trimmer, it is necessary to clean the spark silencer of the engine muffler (Fig. 17). A contaminated spark arrester can adversely affect engine power and mowing quality. Once every three months, check for grease in the gearbox (fig. 18). If necessary, change grease or contact an authorized service center. 10 Fig. 17 Possible malfunctions Malfunction The engine does not start Cause The ignition switch is in the STOP position. Empty fuel tank. Rubber cap for manual pumping of fuel pressed Carburetor overflows fuel (due to improper starting order). Old or improperly prepared fuel mixture. Defective spark plug. The engine is unstable idling. The engine is not gaining momentum. The engine is not developing the necessary dirty air filter. Old or improperly prepared fuel mixture. Old or improperly prepared fuel mixture. The working body of the product is blocked by foreign objects. 11 Fig. 18 Remedies Turn the ignition switch in the direction opposite to that indicated by the arrow on the control handle. Pour clean, fresh fuel mixture into the fuel tank. Fully press the rubber cap for manual pumping of fuel 5-7 times fully. Repeat the start-up procedure by setting the carburetor air flap control lever to position 1 (fully open). Drain the fuel mixture from the fuel tank. Pour clean, fresh fuel mixture. Clean or replace spark plug. Clean or replace the air filter. Drain the fuel mixture from the fuel tank. Pour clean, fresh fuel mixture. Drain the fuel mixture from the fuel tank. Pour clean, fresh fuel mixture. Stop the engine and clean the working tool. power Dirty air filter. Old or improperly prepared fuel mixture. Clean or replace the air filter. Drain the fuel mixture from the fuel tank. Pour clean, fresh fuel mixture. STORAGE Store the trimmer in a clean form in a dry place, inaccessible to strangers, children and animals. Before long-term storage it is necessary to carry out the following steps (preservation): 1. Clean the trimmer, reel with fishing line and cover 2. Drain the remaining fuel from the fuel tank 3. Start the engine 4. The engine must run until it dies 5. Cool the engine ( at least 5 minutes) 6. Remove the plug from the spark plug and unscrew the spark plug 7. Pour a small amount of two-stroke engine oil into the spark plug hole. Pull the engine start cable several times. Install the candle and put on the plug. 12 Unified Technical Support Service E-mail: email@example.com Web site: http://www.huter.su Address of your service center: Additional information on the procedure and place for maintenance and repair can be obtained from the Unified Technical Support Service and at the organization-seller The presented documentation contains the minimum necessary information for the use of the product. The manufacturer is entitled to make improvements to the design that do not change the rules and operating conditions, without reflecting them in the operational documentation. All comments and questions regarding the information provided in the documentation should be sent to the indicated email address. 13 ACCEPTANCE CERTIFICATE “Huter” gas trimmer of the GGT series _ No. _ found to be suitable for use Date of sale _ I am the buyer / representative of the company I have read the operating conditions _ WARRANTY TALON Description of the defect, device number of quality control department manufacturer MP WARRANTY TALON Description of the defect, number of the device OTC manufacturer MP WARRANTY TALON Description of the defect, number of the device OTC manufacturer MP 14 Dear customer! We are grateful to you for your choice. We have done everything possible to ensure that this product meets your needs, and the quality meets the best world standards. The manufacturer sets the official service life for gas trimmers to 5 years, subject to the rules of operation. Warranty period for the “Huter” petrol trimmer. 1 year. The moment of commencement of operation is considered the date indicated by the seller in the warranty card. WARRANTY The manufacturer guarantees the operation of the gas trimmer for one year from the date of sale. Warranty repairs are not made in case of violation of the requirements specified in the passport. Warranty repair is not made in case of violation of the warranty seal (stickers). Warranty repairs are made subject to the seal of the company, the date of sale and the signature of the seller. In the absence of the seal of the seller, the date of sale or signature of the seller, the warranty period is calculated from the date of manufacture. This document does not limit consumer rights defined by law, but supplements and clarifies the obligations stipulated by law, involving the agreement of the parties. COMPLETED WORKS Name of the workshop M.P. COMPLETED WORKS Name of the workshop M.P. COMPLETED WORKS Name of the workshop M.P. 15 16 17 18 19 Huter Elektrische Technik GmbH www.huter.su Rev. 1 20
Gas trimmers are made according to the state of the art and these instructions. It is forbidden to use the trimmer to persons in the state of GGT. 1000T. GGT. 1000s. GGT. 1300T. GGT. 1300S. Engine. 2-stroke, s. Gasoline “Huter” trimmer of the GGT series.
Huter GGT.1500T NEW petrol trimmer at an attractive price, available at SadTeh.ru, 8 (499) 7043336.
Huter GGT petrol trimmer. 1000T is an easy trimmer for carrying out the Operation manual (instruction) of Huter GGT. 1000T. pdf.