How to Replace a Babin on a Trimmer

Replacing the trimmer fishing line: step-by-step instructions for replacing the fishing line on the trimmer

Home »Replacing the trimmer fishing line: step-by-step instructions for replacing the fishing line on the trimmer

How to Replace a Babin on a Trimmer

Trimmers (they are also lawn mowers) are actively used by modern society to care for lawns and other similar objects of horticultural farms. The tool is noted for high efficiency, despite the dubious quality of cutting grass (compared with the usual peasant scythe – earth and sky). The main advantage of trimmers (lawn mowers) is high productivity at low cost of operator’s physical forces. However, over time, the cutting element of the trimmer (kapron scaffold) wears out or becomes damaged, which makes the trimmer a useless tool. From here the task becomes relevant – how to replace the trimmer head and how to replace the fishing line of the trimmer head? Consider this process using the example of Black and Decker lawnmowers and others.

How to replace a fishing line on a trimmer?

Replacing the trimmer’s fishing line with step-by-step instructions will allow even the inexperienced owner of the lawn mower to perform a rather complicated job.

However, before starting work on replacing the fishing line on the trimmer, it is necessary to ensure the safety of the work. In particular, protection measures should be taken against the careless or spontaneous switching on of the mower:

  • Exclude spontaneous start,
  • Remove the battery (if applicable),
  • Place the tool in a convenient working area.

It is convenient to carry out work on replacing the trimmer fishing line when the lawnmower is lying on the table, and the master who is replacing the trimmer fishing line has the opportunity to approach the tool from any direction.

Step 1: remove the trimmer head covers

At the first stage of disassembly, the trimmer head cover is removed. On the example of Black and Decker trimmer models and others, to remove the cover, it is usually sufficient to apply some pressure to release the latch-lock that is located on the side of the head housing.

On some models of lawn mowers, first, the dismantling of the trimmer head is provided, for which the hex key included in the tool kit is used. The head is usually held by two to three screws, accessed through the side openings of the rear decorative cover.

The head cover, where the reel with fishing line is installed, is usually held at the expense of the tongue-latch. It is enough to squeeze the tab-latch with some effort and turn the lid slightly, after which the lid can be easily removed

At the time of pressing the tab-latch you need to slightly turn and lift the cover of the trimmer head to remove the winding drum.

Step two: removing the winding drum (reel) with fishing line

The next step in the process is the recess of the winding drum with fishing line from the inner region of the head. You need to turn the head open side to see the fishing line and reel. On the sidewall of the head, find two recesses (eyes) through which the fishing line is brought out.

You should release the fishing line from the holes by turning the drum, and then carefully remove the reel from the head area. The winding drum of some models is mounted on a spring. This point must be taken into account when performing the extraction operation.

The procedure for removing the trimmer coil with fishing line from the inner area of ​​the head: 1 – the head assembly with a coil; 2 – extraction accurately with a small axial rotation; 3 – extracted parts

Old fishing line is completely removed from the reel. To perform the removal of the old trimmer fishing line, you need to remove the forest from the hinges and pull the free end. This method removes all the old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Installing a new fishing line on the trimmer reel

Equipping the reel with a new fishing line is performed in fact in the reverse order. The procedure looks something like the following, regardless of the model of the mower:

Step One: Fasten and Install

Fold the end of the fishing line in half. Place the blank over the spool on each side of each half of the winding zone. Wrap both halves all the way around the spool. Pull the fishing line through the loop.

The procedure for preparing the engagement of fishing line in the area of ​​both winding sections of the drum. The hinges are laid in specially made cutouts, after which the line is wound in each zone

It is enough to pull the fishing line and put the knot into the groove made on each side of the winding drum.

Step two: winding cutting material into sections

The next step is to wrap the fishing line in a circle around the reel, being careful. It is necessary that each half is filled with “own” winding, exactly, without intersections. Typically, arrows can be seen on the winding drum body indicating the direction of winding. This point should be borne in mind when filling the reel with fishing line.

Step Three: Complete Head Assembly

Pull the ends of the fishing line through a pair of oval recesses in the reel. Replace both washers and spring (if any in the design) with the new components included in the package. Bend both ends of the fishing line at right angles.

The last technical touch of the process of replacing the fishing line on the trimmer is the application of a cover to the head, followed by fixing by pressing force and slight turning.

Skip each end into the hole at the base of the winding drum. Install the coil in the inner area of ​​the head with emphasis on the spring. Put on the cover, align it to the base and lightly press down with a small counterclockwise rotation, put the cover on the tabs of the clamps. This completes the replacement procedure.

Video instruction: replacing the trimmer fishing line

In the video above, it is explained (using an example of the design of an electric and gas mower) how to replace a fishing line in a trimmer. The use of different types of cutting material for cutting grass is noted. The complete process of replacing the cutting material in each section of the winding drum is clearly demonstrated.

The final point of the instructions

Usually the process of replacing fishing line on a trimmer of a particular model is popularly described by the accompanying documentation. Another question is that this documentation is often supplied in a foreign language, since the notorious lawn mowers for the most part are imported products.

Meanwhile, there is a much simpler, more economical and beneficial method for human health and nature – putting the lawns in order with an ordinary peasant scythe. Scythe Blade:

  • Doesn’t “tear” grass stems,
  • Does not uproot plants,
  • Cuts neatly

Which is subsequently accompanied by abundantly growing greens, and not the formation of dead wood as a result of the trimmer.

Replacing the fishing line in the trimmer: 2 easy ways

The trimmer is a necessary and useful tool for a summer cottage and a private house. Many own and actively use it, but not everyone knows how to replace a fishing line in a trimmer, especially at first.

In this manual, we will step by step analyze the entire replacement process. Looking ahead, there are two ways to tackle the trimmer spool with fishing line. There is no fundamental difference – the difference is that in the first case there will be one fishing line, folded in half, and in the second there will be two lines of such lines.

Content:

Replacement Preparation

Disassemble the trimmer spool

For clarity, the mowing head (spool) was removed from the lawn mowers. To replace the fishing line, you do not need to remove it, everything is done locally. It does not take much time.

We disassemble the trimmer spool – it rests on the latches-latches. Remove the cover by pressing on the latches. If you do not have enough effort with your hands, then use a screwdriver.

The spool consists of the following:

  • Spring housing
  • Locking lid
  • Button Coil

The principle of action is as follows. By pressing the button, the coil presses on the spring and exits the locking grooves in the spool cover. While holding the coil in this state, you can twist, thereby adjusting the length of the fishing line. When you release the button, the housing spring returns the coil to its original fixed state.

Disassembled Trimer Spool

Bottom on the coil there are several holes for different diameters of the lines. Different trimmer manufacturers may vary. In some cases (as here) they are signed, in others not.

These holes are needed to fix the fishing line when replacing it. After winding on a woman’s fishing line, the ends of the latter are inserted into them. This is necessary so that the scaffold does not unwind at the time of installation of the coil in the trimmer housing. In other words, it facilitates the replacement of fishing line.

Fishing Line Holes

There are models without specifying the diameter of the consumable. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on through the holes for withdrawing fishing line from the body of the trimmer spool (see figure below).

Fitting on fishing line outlets

The reel has two sections for fishing line, separated by a partition. They may not be. They are needed only to distinguish and facilitate winding of the consumable.

Two sections for fishing line

Initially determined with the required length of the loess. The latter is wound in one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length was about 2 meters. Those. For two sections you will need a 4 meter cut – this is for the 1st method. For the second method, you need two segments of 2 meters.

Determination of the required length of fishing line

Now you need to figure out which side you need to wind it. To do this, many manufacturers of trim tabs on the coils apply special designations such as in the figure below.

Special designation on the reel

If such designations were not found, then you need to pay attention to the body of the spool. There is without fail an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.

Designation on the spool housing

First way

Bent in half fishing line

The prepared segment (in this case, 4 meters) is bent approximately in half – one segment should be 15-20 cm longer and inserted into a special slot located on the dividing partition.

The fishing line is inserted into the slot

In a previously defined direction, a fishing line is wound. This is done in a tight fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.

There are designs in which the division of the coil into two sections is not provided. This does not change anything, the fishing line is wound in a similar way. It is only necessary to ensure that the segments do not overlap among themselves.

The first segment that ends at the bottom of the coil, i.E. One that is closer to the fixing holes.

This tip is placed in the corresponding diameter hole. The fishing line is firmly fixed.

The fishing line is firmly fixed

A long section is wound another half turn. There it is fixed in a similar way. In this case, the segment crosses another section of the coil.

A long section is wound another half turn

The fixed ends of the wound fishing line are inserted into the holes of the trimmer spool housing.

The fixed ends of the wound fishing line are inserted into the holes of the trimmer spool housing

The coil is attached to the body. The ends of the fishing line are pulled with force so that the fishing line previously fixed in the holes of the reel springs out. This is easily determined by the characteristic sound (click).

The ends of the fishing line pull

The button coil is latched into the trimmer spool housing.

Coil with button snap into the trimmer spool housing

Replacing the fishing line was successful. In this case, you need to install it back on the trimmer and you can start mowing the grass.

It should be repeated, you do not need to remove the spool from the trimmer – this was done to make the process of replacing the fishing line easier. You can disassemble the spool in place, wrap it on a reel and put it back.

Successfully replacing fishing line

The tips so that they do not hit the trim cover can and should be trimmed.

Method 2 – two segments

Two wound lengths of fishing line

Method number 2 fundamentally no different from method number 1. The only difference is the two winded pieces of fishing line, instead of one.

The end of each segment is bent

The end of each segment is bent.

Two special locking sockets

There are two special locking sockets on the coil (see figure above).

Start winding the fishing line

They hook onto it with a hook formed earlier on the fishing line, and begin to wind the fishing line.

Winding is carried out in a special order.

The winding should be carried out in the following order: first the bottom line, i.E. The one that is closer to the fixing holes at the bottom of the coil, and only then the upper one, i.E. One that will overlap the bottom section.

The bottom line is wound

The tips are made into the holes in the body of the trimmer spool. They are pulled up to a click, which indicates that the line has come out of the clips.

The tips are threaded into the holes of the trimmer spool housing

The coil is fastened into the housing. The fishing line in the spool is replaced.

The fishing line in the spool is replaced

VIDEO: How to wind a fishing line on a mowing head trimmer or lawn mowers

How to wind a line onto a mowing head of a trimmer or lawn mowing machine

Replacing the fishing line in the trimmer: 2 easy ways

Feedback from our readers is very important to us. Leave your rating in the comments with the argument for your choice. Your opinion will be useful to other users.

Change Trimmer Trimmer Video

How to trim? Video-instruction

Factory trim trim warranties will inevitably require replacing the mowing line. Having a very rough idea of ​​how to fill the fishing line in the trimmer coil yourself, beginners are reluctant to deal with this issue. However, with some skills in mastering this simple science it does not present any difficulties, and the instruction below will facilitate this process as much as possible.

Preliminary preparation

First of all, to wrap the fishing line, you need to remove the reel (reel, reel) from the trimmer. Specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers with the operating position of the engine and the coil at the bottom usually have side keys on both sides of the coil. By pressing them simultaneously, the upper part of the coil, together with the internal contents for winding the mowing line, is turned off, and the lower part remains on trimmer. It is advisable to analyze the reel on a flat, level place so that the spring entering the structure does not jump out and is not lost;
  • Electric and gasoline trimmers with a curved shaft without the possibility of installing a knife, usually have coils with a special lamb: in such designs, hold the coil in one position with one hand and rotate the locking coil on the wing rod counterclockwise. After disconnecting the nut, the entire drum is removed.
  • Electric and petrol trimmers with the possibility of installing the knife on a straight rod (for example, Calm Trimmers) under the coil have a hole. For the immobility of the rod, a screwdriver or other suitable object is inserted into this hole, and with slow rotation, this mutual arrangement is achieved when the screwdriver enters the hole and the coil is fixed. After that, the coil body scrolls clockwise (with left-hand thread) and is removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in various ways. In mutton drums, the lamb is twisted, in the coils with latches, the latches are clamped and one part of the coil is released from the other. If the halves of the bobbin are threaded, it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Manual lawn mower. Replacement fishing line in the coil.

Related posts

In this video, I show how easy and easy to reel. Fishing line to reel a manual lawn mower yourself.

Replacement fishing line on the lawn mow.

How to wind the cutting cord onto the lawn mowing coil (trimmer) yourself

We wrap the fishing line

Slowly finished disassembling the coil of the coil without losing its spare parts allows you to move on to the main task. Winding reels. Technological features of the design of the reel and the number of working antennas determine the sequence of actions.

Coil with one working antenna

The simplest version and simple sequence of actions:

  1. The dimensions of the bobbin and the length of the factory winding determine the recommended length for winding the mowing line. 2.5 m.
  2. One end of the mowing line is inserted into the mounting technological hole inside the bobbin.
  3. Fishing line is wound on the drum during reverse rotation of the bobbin in the direction of the trimmer product. As a rule, on the inside of the bobbin, an arrow indicates which side is wound.
  4. A small portion of the mowing line remains free so that it can be pulled out. It is fixed in a special groove on, designed to hold the winding when the coil is assembled in working condition.
  5. The left end of the mowing line passes through the hole on the outside of the reel.
  6. Half of the coil is assembled and mounted on the trim tab of the trimmer.

Coil with two working antennas

Related posts

In these types of coils, the number of grooves for winding the cutting line lying inside the coil should be determined:

  • One groove. Both antennae are wound together along one groove;
  • Two grooves. Each barbel is wound on a separate groove.

In both cases, a fishing line with a length of 2-3 m is taken. In reels with one reel, the fishing line is drawn into the through hole, its ends (antennae) are folded together and aligned, and then wound in the opposite direction of rotation of the drum from the side of the rod. An arrow usually indicates the correct direction of winding. In the presence of fixing grooves, the ends of the mowing line can be traced in them or held by the fingers of a free hand, pass through the through hole of the outer half of the bobbin, the bobbin is closed and attached to the finish rod.

The difference between the winding of the mowing line in coils with two coils is that initially the length of the mowing line 2-5 m is folded in half (to determine the average fold), and the folding loop is inserted into a special groove between the grooves, Both tendrils of the mowing line are wound around each groove, the fixation of the antennas and the coil assembly are similar to the one-groove option described above.

The first implementation of this procedure can be long and rather laborious, but with time and experience this problem will be solved much faster and easier.

The video below will clearly show how to fill the line in and rewind it correctly. This operation is not difficult and with some patience will certainly succeed:

Automatic reeling of mowing line

There is a kind of coil in which the automatic mechanism wraps itself. From the user it is enough just to fill the fishing line correctly. The fishing line passes through the hole inside the case, its antennas without winding pass through the hole on the outer case, the coil is assembled, and when the winding button is turned, the fishing line inside spins independently. In such a coil, it is impossible to make the winding wrong: the mechanism itself will determine the right direction, since it can only turn in one direction.

Video: How to Replace a Babin on a Trimmer


How to Change a Fishing Line On a Trimmer Video

The most worn out element in the trimmer design is fishing line. Therefore, it is important to know how to choose and wind it on a reel. All the details in the article.

How change fishing line in trimmer and which is better to choose

Since we considered the choice of the trimmer in the previous article, today we will tell you how to properly trim the trimmer with a fishing line, and which is better to choose based on the working conditions.

After you bought a trimmer and began to use it actively, sooner or later the question will arise about replacing the fishing line, since this is the most wearing element in the tool, then intensive use of the trimmer will lead to frequent replacement of consumables.

What types of woods are

The most common type of fishing line that fits almost all types of round cord reels. This is an ordinary fishing line suitable for mowing juicy grass, but mowing dead wood with it will be much more difficult, and even more so it can not cope with the bush.

As a rule, the diameter by which young grass can be mowed does not exceed 1.6 mm. The thicker the thread, the more coarse grass it can overcome.

There are fishing lines with sharp edges in the form of an asterisk or square, this option is more suitable for mowing dry grass just due to the existing sharp edges, but its disadvantage is more wear and tear and is inferior in strength to round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but they are used only on lawn mowers, since the exit of such a thread from the reel is difficult, it is used most often with discs into which segments are inserted. The disadvantage of this product is its fragility.

Manual lawn mower. Replacing fishing line in the coil.

In this video, I show how easy and easy to reel. Fishing line to reel a manual lawn mower yourself.

Replacing fishing line on the lawn mow.

How to wind the cutting cord onto the lawn mowing coil (trimmer) yourself

Most often in gas trimmers with an engine power of more than 1.5 hp apply cords with a metal cable inside. This thread is ideal for mowing dry grass and small bushes. The presence of a core positively affects the wear resistance of this material. The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

How fill up the fishing line into the trimmer coil

It takes about 10-15 minutes to wind the line. What is a trimmer coil? Plastic case with a cassette inside, on which there is a special hook for convenient winding of fishing line. Almost all trimmer coils have a similar mounting principle, this is the central screw-button, when pressed, it becomes possible to pull the fishing line of the required length. The photo below shows some examples of different coils for trimmers.

The bobbins of the trimmers, the motor of which is located near the ground, have a different mount to the axis of rotation, they have two buttons on the spool located on the sides that need to be pressed, otherwise the thread replacement is no different from other cassettes.

The principle of proper winding fishing line is similar in all above listed cases, so for example, consider the standard version with two antennae.

To remove the reel with fishing line, it is necessary to unscrew the screw located in the center, but note that the thread there is left, so you have to turn it clockwise, this is done specially so that during operation it does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and remove the coil, which is directly wound fishing line. Having measured the necessary length and folded in half, you need to fill the fishing line into the reel, removing, in the end, its ends opposite each other (for this there are special slots for fixing).

After this, it is necessary to assemble the head in the reverse order by threading the ends of the cord into two corresponding holes.

If in doubt or it is not entirely clear how to charge the fishing line to the trimmer, we recommend that you look video: How to wind a line in a lawn-mower. In this video, the instructor will open the trimmer head in steps, measure out the required amount of fishing line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.

How to Change a Fishing Line On a Trimmer Electric Video

How change fishing line in trimmer and which is better to choose

Since we saw the choice of the trimmer in the previous article, now we will tell you how to correctly trim the trimmer with fishing line, and which is better to choose based on the criterion of work.

After you have purchased the trimmer and started to use it intensively, at some point the question arises of replacing the fishing line, since this is the most wearing element in the tool, then the saturated operation of the trimmer will lead to frequent replacement of consumables.

What types of woods are

A common type of fishing line that fits virtually all types of reels is a round cord. The engine on an electric trimmer on them, since it is not a protective cover c. This is an ordinary fishing line, suitable for mowing juicy grass, but it will be much more difficult to mow dead wood with it, and even more so it does not cope with the bush.

Usually, the diameter, which can be used to mow young grass, does not exceed 1.6 mm. How to wrap fishing line on a reel? How to refuel fishing line in a video about how. How to change the fishing line on the trimmer below me video on the fishing line on. The thicker the thread, the more coarse weed it can overcome.

There are fishing lines with ground edges in the form of an asterisk or square, this option is more adapted to mowing dry grass just due to the existing sharp edges, but its drawback is more wear and tear and is inferior in strength to round cord.

Related posts

There are fishing lines with improved aerodynamics with corresponding dents, scales and notches, a similar product makes less noise, but they are used only on lawn mowers, since the exit of such a thread from the reel is difficult, they are used in most cases with discs into which segments are inserted. Video how to disassemble on the mower head to wind the fishing line into the trimmer. How to cut and change to inspect everything on a trimmer on a spark plug. The disadvantage of such a product is its fragility.

In most cases, in gas trimmers with an engine capacity of more than 1.5 hp. Use cords with an iron cable inside. Lubricating the gearbox, replacing the fishing line, how to change the line on the lawn mower, see the video. This thread is perfect for mowing dry grass and small shrubs. How to change a knife on a trimmer to install a disk; in the reverse order to collect the lawn mowing. How to rewind a fishing line on a trimmer yourself. The presence of a core positively affects the wear resistance of this material. The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

Replacing fishing line on the lawn mowing.

How to wind the cutting cord onto the lawn mowing coil yourself (trimmer)

HOW TO CHANGE THE FISHING LINE FOR THE TRIMMER ELECTRIC

IN THAT VIDEO I WILL SHOW HOW CHANGE THE FISHING LINE ON THE TRIMMER ELECTRIC. THIS DOES NOT MAKE.

How fill up the fishing line into the trimmer coil

In order to reel fishing line, it will take about 10-15 minutes. How to exchange a knife for a knife on a trimmer. Replace the knife with a Stihl trimmer, easy to. What is a trimmer coil? Plastic case with a cassette inside, on which there is a special hook for convenient winding of fishing line. Almost all trimmer coils have a similar mounting principle, this is the central screw-button, when pressed, it becomes possible to pull the fishing line of the required length. How to wind fishing line on different coils in lawn mowers. How to change a knife on a trimmer (including a video instruction). How to bet on. I shot this video on request. I thought that I wouldn’t have to show this, but, apparently, this is also necessary. The photo below shows some examples of different coils for trimmers.

Related posts

The bobbins of the trimmers, the motor of which is located near the ground, have a different mount to the axis of rotation, they have two buttons on the spool located on the sides that need to be pressed, otherwise the thread replacement is no different from other cassettes.

The principle of proper winding fishing line is similar in all above listed cases, so for example, consider the standard version with two antennae.

To remove the reel with fishing line, it is necessary to unscrew the screw located in the center, but note that the thread there is left, so you have to turn it clockwise, this is done specially so that during operation it does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and take out the reel, on which the fishing line is directly wound. Having measured the necessary length and folded in half, you need to fill the fishing line into the reel, removing, in the end, its ends opposite each other (for this there are special slots for fixing).

After this, it is necessary to assemble the head in the reverse order by threading the ends of the cord into two corresponding holes.

If in doubt or it is not entirely clear how to charge the fishing line to the trimmer, we recommend that you look video: How to wind a line in a lawn-mower. Stihl how to replace a fishing line in a trimmer as a video. Replacement change the fishing line in the trimmer. In this video, the instructor will open the trimmer head in steps, measure out the required amount of fishing line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.

How to wind a fishing line on a trimmer reel: winding methods and video

Any garden owner knows how quickly weeds can flood the area. To defeat them without excessive efforts will help the trimmer. This incredibly useful device is an indispensable tool for trimming and mowing grass.

It’s no secret that a conventional lawn mower can be used far from everywhere. In contrast, the trimmer can handle even very complex areas. This is especially true for those tools in which the cutting element is not a knife, but a fishing line.

Features of the use of trimmers

The trimmer mowing grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, aisles in the garden.

Such a convenient, and most importantly, effective device, as a trimmer, exists in several variations:

As the names indicate, the types of trimmer are noticeably different from one another. But regardless of the type of tool, it the cutting element may be a fishing line. Of course, the line tucked into the reel of the trimmer is not infinite. And sooner or later it will be necessary to replace it with a new one.

The consumption of fishing line depends on on frequency of use device and scope of work performed. The more grass is cut and the more often it is trimmed with a trimmer, the more actively the line is consumed in it. And, accordingly, the faster it will end. In this regard, the question arises: how to fill the fishing line into the coil of the trimmer?

Not everyone knows the answer to this question. But winding fishing line on a reel plays an important role in the trimmer. In order for the device to function normally, it is very important to correctly wind a new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

Which fishing line to choose

Before you stock up on this material for refueling in the trimmer, you need to make a choice. After all, the usual so-called round fishing line is far from the only existing species. How to choose the most suitable? First you need to determine the working conditions.

Type selection. A fishing line with a circular cross section is the most common. It will fit any coil with the rarest exceptions. This type of consumable is suitable for mowing fresh, juicy grass. But mowing the so-called dead wood, this species may no longer be able to cope. It is pointless to mention attempts to mow shrubs with this thread.

In addition to the usual type, there are others, having sharp edges. Usually they are made with an “asterisk” or “square”. The presence of sharp edges is the main feature and key difference of these threads.

It is because of this peculiarity that the threads of such species are able to mow dry weeds. But the pointed threads are not without flaws, the main of which can be called quick wear and strength noticeably inferior to the round type.

In addition to the types of woods already mentioned, there are also interesting and common varieties. Especially among them can be noted fishing lines, inside of which stretched metal wire. Threads of this type are often used in tools that run on gasoline and have an engine more powerful than one and a half horsepower.

Threads with a metal core are like with round section and with sharp edges. Regardless of the type of cross-section, such threads are the best suited for overcoming mowing plants. Threads belonging to this type easily mow not only dry grass, but even small shrubs.

Threads with wire inside compare favorably with other types of consumables incredible durability. But unfortunately, this feature has a more than noticeable effect on the price of this type. The cost of threads with a core significantly exceeds the cost of threads of other types.

Thickness selection

In addition, special attention should be paid to the thickness of the consumable. For mowing young grass, a thread with a diameter within one and a half millimeters is suitable. The larger the diameter of the thread, the drier and coarser weeds it can overpower.

When choosing a fishing line by thickness there is one “but”. It is important not only to evaluate the capabilities of the material, but also to take into account the features of the trimmer. Necessary take a look at the user manual, which is attached to the tool and find information about the requirements for the cutting element.

Using the wrong thread may cause the tool to malfunction. Using a thread that is too thick will overload the motor of the device. And the use of too thin thread at times will increase the wear of the twisting mechanism.

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel it in the trimmer. When a suitable fishing line is found and acquired, you can begin to consider ways to wind it on a reel.

How to wind a line onto a trim reel

At first glance, refueling a fishing line into a tool reel is not an easy task. But it is enough to carefully study this process – and in the future, all necessary actions will be carried out without any difficulties.

To learn how to refill a fishing line with a trimmer, read this guide. The step-by-step instruction below takes into account the features of the coils of different types of trimmers, therefore applicable to any instrument.

So, the procedure is as follows.

  1. The fishing reel is the bottom end of the trimmer. First things first, of course, you need to remove this head from the device. To do this, fix the rod (or, in other words, the shaft) on which the coil is mounted. It is necessary to fix it in such a way that it does not scroll. It is easiest to do this by placing a kind of stupor (preferably metal) between the shaft thread through a special hole. When the shaft is locked, you can unscrew the coil.
  2. At this stage, the bobbin to attach the fishing line to is removed from the head. To do this, you need to disassemble the head into elements. To do this, you must first find the latch on its body. It is located on the circumference of the product and is like a button. When the latch is found, you need to press it with effort. Keeping the lock pressed, turn the head cover clockwise. Then you need to remove the cover and remove the bobbin.
  3. A tight spring is placed between the bobbin and the head. It needs to be temporarily set aside so that it does not interfere with the winding process. Before proceeding to the line of winding fishing line, it is necessary to inspect the bobbin. If it contains the remains of an old fishing line, they must be removed. When the bobbin is clean, you can begin preparing a new skein.
  4. It is necessary to measure and cut six (maximum – seven) meters from a previously prepared skein of new fishing line. The bobbin should be at hand.

At this point, actually begins the key stage, which this article is devoted to.

The first way to wind the line

The right amount of fishing line is cut off. Now you need to carefully inspect the bobbin, in order to understand what type it belongs to. It depends on how the line is to be wound on it.

There are two types of bobbins. In general, they are slightly different from each other. Regardless of the type, the coil is divided into two compartments – upper and lower. In the first type, the dividing face does not close into the ring and has a recess.

In the second type, it is solid, but near it on the sides on both sides there are small through holes. The method of winding the thread needs to be studied depending on which of the above types the coil belongs.

  • The previously prepared six-meter segment must be bent in half. It’s best not exactly in the middle, but in such a way that one half is about fifteen centimeters longer.
  • Then the place of the bend must be inserted into the recess in the dividing face. One half of the fishing line should be at the top of the reel, the other half at the bottom.
  • Now you can proceed directly to winding. You need to wind it in the direction that the arrow on the bobbin points. When winding, you need to hold the threads so that they do not intertwine and the upper half is wound into the upper part of the spool, and the lower half – into the lower part. Each half should remain free about fifteen centimeters from the end.
  • In the upper face of the bobbin there are small recesses (or, in other words, grooves) for fixing the consumable. The ends of the threads must be inserted into these recesses so that they are fixed one opposite the other.
  • The final stage of refueling consumables in the tool – the ends attached to the bobbin must be threaded into the corresponding holes in the trimmer head.
  • That’s all. The winding process is complete. Now it remains only to assemble the head into a single whole. The spring is carefully placed back between the bobbin and the head. Then you need to insert the bobbin into the head and press them together.
  • It is recommended that the loose ends of the thread be pulled outward. To do this, you need to take turns pulling the ends of the consumable so as to remove them from the grooves of the bobbin. You can make sure that the cutting element is removed from the retaining grooves by trying to pull the threads out a little – they should freely exit through the holes in the head.
  • While holding the bobbin down, put a cover over it. The cover must be screwed to the head so that all the grooves on their bodies are aligned and the bobbin remains fixed between them.
  • And finally, the most recent action – the head is screwed back into place at the bottom of the tool.

The process is completed. The line is tucked into a reel. The trimmer is ready for further work.

Second winding method

  • A previously prepared six-meter-long section, it is required to bend exactly in the middle and cut it. Thus, two segments of the same length are obtained.
  • At one end of each segment you need to make a small “hook”. To do this, it is necessary to bend a couple of centimeters from the edge and briefly fix it so that the “hook” does not bend.
  • Then one piece is taken. A “hook” is inserted into the through hole at the top of the bobbin.
  • Now you can proceed to the key stage – winding. The direction in which you want to wind is indicated by the arrow on the bobbin. It is important to ensure that the line is wound strictly within the top of the reel. Winding the thread to the very tip is not necessary – from the end should remain free about fifteen centimeters.
  • In the upper face of the coil there are small recesses (the so-called grooves) for fixing the consumable. The loose “tail” of the thread must be inserted into one of these recesses.
  • The top of the coil is tucked. Now you need to do the same procedure with the bottom. The second length of thread is taken. A “hook” is threaded through a hole in the bottom of the bobbin.
  • After that, you can begin to reel the fishing line (within the lower compartment). And at this stretch of free you also need to leave about fifteen centimeters from the end. This remaining “tail” must be inserted into the recess opposite to the one into which the end of the first segment is inserted.

The subsequent steps for this type of coil are exactly the same as those described for the previous type in steps five through nine.

This is how the fishing line in the trimmer coil changes. Nothing no complicated in the process. And after a few refueling completed, all actions will reach automatism.

To visually study the process described above, you can turn to the Internet for help. The popular YouTube portal has many different videos with a demonstration of winding fishing line on a trimmer reel.

I want to devote today’s article to the sore topic of summer residents and gardeners of the entire post-Soviet space "How to refill a fishing line into a trimmer." Not many trimmer manufacturers answer this question in their operating instructions. Therefore, it is difficult for ordinary gardeners to figure out how to do this correctly.

I want to start with a brief description of the technical characteristics of the trimmers.

So, trimmers are electric and gasoline. The cutting element of the trimmers can be a fishing line and a knife. The fishing line is ordinary, four. Pentahedral and intertwined (in the form of a pigtail). Knives come in 2, 3 and four blade blades. Knives are also plastic and metal.

The feed system of the fishing line from the trimmer is manual, semi-automatic and automatic.

Development engineers who create new models of trimmers clearly calculate the diameter (thickness) of the fishing line and the number of knife blades according to the power of the trimmers. Otherwise, the engine is overloaded, which as a result leads to its breakdown. And this is an additional and significant cost.

Today on the market are trimmers:

With one nozzle – only fishing line.
With two nozzles – fishing line and three-four-blade knife.
With one nozzle – only a three-four-blade knife.

Our Kulibins long ago learned to improve any mechanisms. So, for example, some gardeners make successful, in their opinion, replacing the fishing line with a metal cable, or fishing line. But at the same time they do not think about the safety of their and their loved ones, because, as a cable with the power of a working trimmer, it can easily break out and not only injure the mower and others, but leave it crippled for life. Using fishing line can and gives a better effect, I have never personally tried it than fishing line for trimmer, but this work has a number of disadvantages: when it comes into contact with solid objects, it loosens or can simply be pulled out of the reel without limit.

So what is called closer to the topic. I give an example of how to fill a fishing line into a trimmer (BOSCH Art 30 trimmer). Everything is very simple. We started.

After you have chosen the fishing line for refueling, you need to cut off the necessary amount of fishing line, because all the fishing line in the skein is not wound into a reel.

Cut off and start winding.

Remove the coil and the protective cover from the coil.

They took off. We fix one end of the fishing line into the gap and carefully and evenly wind the fishing line.

The amount of fishing line should be such that the protective cover of the reel closes and the line on the reel unwinds itself a little.

The second end of the fishing line is planted in the hole on the protective cover.

Next, take the coil and the protective cover of the coil. We sink the end of the fishing line from the reel into the metal hole on the protective cover of the reel. Tighten the fishing line a little.

We put it all on the trimmer. Turn the coil clockwise until it clicks.

Secured. Now connect the trimmer to the network. We put the trimmer in the starting position for the job. Turn on the trimmer. The excess length of the fishing line will be cut off on the cutting blade.

Trimmer Coil

That’s all starting work.

You can watch the video

A little tip. Make sure that the fishing line does not come into contact with solid objects when cutting. With this contact, the fishing line will be cut. And since, in this trimmer, the fishing line is not fed automatically, then you have to stop the work each time, remove the reel and re-release the fishing line.

In my trimmer, in addition to the standard line for mowing the lawn, there is still provided a thick fishing line for mowing coarse weeds. It has the shape of a pigtail, i.E. Three fishing lines are tightly intertwined. Such a fishing line has its own reel.

Thick fishing line

It is stored at the top of the trimmer body.

Spare coil storage space

Installing such a fishing line into the reel is very simple – according to the internal circuit inside the reel. We insert the center of the fishing line with a metal mount at the top of the reel, and draw the ends of the fishing line along the grooves and bring it out.

Reinforced Fishing Line

Such a coil is attached to the trimmer as well as a reel with ordinary fishing line.

  • What types of woods are
  • How to remove or refill a fishing line in a trimmer

Since we considered the choice of the trimmer in the previous article, today we will tell you how to properly trim the trimmer with a fishing line, and which is better to choose based on the working conditions.

After you bought a trimmer and began to use it actively, sooner or later the question will arise about replacing the fishing line, since this is the most wearing element in the tool, then intensive use of the trimmer will lead to frequent replacement of consumables.

What types of woods are

The most common type of fishing line, which is suitable for almost all types of coils – round cord. This is an ordinary fishing line suitable for mowing juicy grass, but mowing dead wood with it will be much more difficult, and even more so it can not cope with the bush.

As a rule, the diameter by which young grass can be mowed does not exceed 1.6 mm. The thicker the thread, the more coarse grass it can overcome.

There are fishing lines with sharp edges in the form of an asterisk or square, this option is more suitable for mowing dry grass just due to the existing sharp edges, but its disadvantage is more wear and tear and is inferior in strength to round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but they are used only on lawn mowers, since the exit of such a thread from the reel is difficult, it is used most often with discs into which segments are inserted. The disadvantage of this product is its fragility.

Most often in gas trimmers with an engine power of more than 1.5 hp apply cords with a metal cable inside.

This thread is ideal for mowing dry grass and small bushes. The presence of a core positively affects the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

How to remove or refill a fishing line in a trimmer

It takes about 10-15 minutes to wind the line. What is a trimmer coil? Plastic case with a cassette inside, on which there is a special hook for convenient winding of fishing line.

Almost all trimmer coils have a similar mounting principle, this is the central screw-button, when pressed, it becomes possible to pull the fishing line of the required length. The photo below shows some examples of different coils for trimmers.

The bobbins of the trimmers, the motor of which is located near the ground, have a different mount to the axis of rotation, they have two buttons on the spool located on the sides that need to be pressed, otherwise the thread replacement is no different from other cassettes.

The principle of the correct winding of the fishing line is similar in all of the above cases, so for example, consider the standard version with two antennae.

To remove the reel with fishing line, it is necessary to unscrew the screw located in the center, but note that the thread there is left, so you have to turn it clockwise, this is done specially so that during operation it does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and take out the reel, on which the fishing line is directly wound.

Having measured the necessary length and folded in half, you need to fill the fishing line into the reel, removing, in the end, its ends opposite each other (for this there are special slots for fixing).

After this, it is necessary to assemble the head in the reverse order by threading the ends of the cord into two corresponding holes.

If you have doubts or it’s not entirely clear how to charge the fishing line to the trimmer, we recommend watching the video: how to wind the fishing line into the lawn mowing properly.

In this video, the instructor will open the trimmer head in steps, measure out the required amount of fishing line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.