How to start a motor block without a starter. Repair sequence

How to start a motorcycle block?

Motoblock is a reliable assistant in agriculture, who regularly performs the hardest work in the field, simplifying the life of farmers. The technique is used to prepare the soil for planting crops, watering, hilling, weeding plants, digging potatoes. To ensure a productive performance of the walk.Behind tractor, it is necessary to ensure competent maintenance and care, to comply with the operating rules specified in the guidance.

Immediately after buying equipment, do not work at maximum power. Start the device only after taking it out of the package, not worth. Even if you hear from consultants that the car is completely ready for use, do not risk, start with the preparation of a new walk.Behind.

How to start a motorcycle?

After you bought your walk.Behind tractor, you should not immediately start it, even if the consultants assure you that the equipment is completely ready for operation. You need to start with preparatory work.

To do this, you need to first check the oil level in the engine. It should be enough. If not so, oil needs to be added. If you run the engine without oil, it will immediately fail. On sale you can find motoblocks, such as Caiman, which have an oil level sensor. If the lubricant is not enough or it will be absent at all, the engine will simply not start. It is very convenient and significantly extends the service life of your equipment.

After that you need to fill in the fuel. During the purchase, check with the consultant or in the operating instructions the type of gasoline, which is suitable for your motoblock model. If the unit has a two.Stroke engine, then fuel must be diluted with oil in a certain ratio. Never use low.Quality fuel, as well as one that is not suitable for your walk.Behind tractor.

The final stage of preparing the machine for launch is to check all connections and fasteners. All moving elements should not be tightly tightened. Their work should be elastic, but smooth.

The launches of diesel and gasoline motoblock are slightly different among themselves. The gasoline unit is launched in this way:

  • Open the gasoline valve;
  • The lever of the suction should be in the “launch” position;
  • The ignition must be turned off;
  • Pump a mechanical starter a couple of times;
  • Now you need to turn on the ignition;
  • Turn the starter again.

If you have an electric starter, then you can immediately turn on the ignition. Starter quickly pumps fuel to the carburetor.

start, motor, block, starter

With diesel motor block, things are a little more complicated. The new unit is completely dubbed, unless, of course, no one started it. To pump it, you need to twist the starter. The process will be longer than in the launch of a gasoline machine, but as a result, a walk.Behind tractor will start.

If you have a manual starter, then you can twitch it, but you can have a walk.Behind tractor in another way. To do this, you need to open a fuel tap, and already from it to spin each connection to the nozzle itself. You unscrew the connection, wait for the fuel to pour, and twist it, moving on to the next.

With a mechanical start, you need to open all the taps and put the gas in the middle position. Squeezing a decompressor, download a couple of times, holding it with your finger. After that, lower the decompressor and pull it until its initial position. Press it again and do not hold it, but immediately pull the starter. The motorcycle block should earn.

Main recommendations for common models

Motoblocks in the market are represented from different manufacturers. But, as practice shows, there are several models that domestic consumers trust most and buy them more often:

Accordingly, the launch rules differ. If such steps should be performed: the transfer of the ignition switch to the ON status, slam the damper (completely) and open the fuel crane; set the gas lever ¾ from the maximum position, pull the starter cable and push the damper.

The motoblocks of the Minsk Plant (MTZ) need a slightly different approach. Gasoline models with a manual starter are trained according to the following scheme: open the fuel crane, set the lever for the launch, turn off the ignition and pump the starter 3-5 times. Then you need to turn the key in the lock and again pull the starter. After starting the lever, the lever is transferred to the working position. Diesel models require pumping (to shake the remaining air), after which you need to sharply twist the starter until the engine starts.

start, motor, block, starter

The engineers messed up: we list all the problems of the Renault 2.2 dCi (G9T) engine. Subtitles!

To launch the Urals, you need to resort to such work: set the neutral position of the gearbox lever and open a gas tank. Then you need to completely close the throttle control controller and partially cover the air damper. Then start the engine using the cord.

The launch of the “patriot” implies a different procedure for actions: the removal of the gas lever to the highest position, the jerking cable for purging. First stretching hard and for a long time, then with short jerks to launch the motor, and then regulate the gas handle.

The correct launch of the walk.Behind tractor after winter

Before starting Motoblock after long winter downtime, it is necessary to paint it painstakingly. First you need to take out the equipment from the garage and look around it. There should not be foci of corrosion on the iron surfaces of the agricultural protection, the occurrence of which can be provoked by the highest humidity. In the case of corrosion forms, it will need to be removed, problematic areas with a special rust converter and paint areas.

  • Drain the old fuel from the tank, also remove the old reducer lubricant. The latter must be painstakingly wash and dry. Then you need to fill in fresh fuel and new transmission oil;
  • Wash the fuel tubes, make sure that they did not lose their density and cracks did not appear on their walls;
  • Remove all filter elements provided for in the design, painfully wash them in clean gasoline, dry and install them back. The crumpled filters must be changed;
  • Remove and disassemble the carburetor, blow it with compressed air or wash it with gasoline. After that, one hundred percent dry parts of the fuel node must be assembled and installed in place;
  • Check the drive belts-due to the highest humidity on their surface, cracks might appear-in this case, the elements must be changed immediately;
  • To disassemble and look around the unit CPG. If burrs or traces of rust appeared on the walls of the node, then they will need to be removed;
  • Turn out and check the candle. There should not be traces of scale and tarry deposits on it. In an unpleasant case, the candle must be cleaned and dried. After that, it is necessary to ventilate the engine, a couple of times sharply pulling the starter cable;
  • Check the gap of the ignition system and Ponova put it if it was broken;
  • Look around the controls and make sure that gas and brake cables are stretched because it is required for work;
  • Remove, charge and install the battery back if it is provided in the design of the walk.Behind tractor. At the same step, it is necessary to check the terminals and contacts of the electrical wiring. There should be no traces of oxidation on them;
  • Check the tire pressure and pump them up because the abstract shows to the walk.Behind tractor;
  • Look around the chassis of the walk.Behind tractor and wrap the weakened bolted mounts;
  • Check the mechanism for connecting the suspended and trailer equipment.

Only after all the listed actions can a walk.Behind tractor be launched.

So Bind Agricultural machine with a gasoline engine, you need:

  • Open the tap for supplying gasoline. At this time, the fuel lever should be placed in the “Start” position, and the clutch lever in the “disconnected” position;
  • Carry out pumping with a manual starter, a couple of times abruptly pulling his cable over him;
  • Translate the ignition lever to the “inclusive” position and pull the starter cable a couple of times a couple of times;
  • As the engine of the used walk.Behind tractor will be launched, it will be necessary to rapidly transfer the fuel lever to the “work” position.

Motor starter repair #shorts #mechanicmike88

If an electric motor unit is provided in the device starter, then the operator is enough to turn on the ignition and press the engine start button.

Starting a diesel motorcycle block is little more difficult.

  • Unscrew the crane created to serve fuel, evenly promoting each standard connection from it;
  • As a fuel reaches the nozzle, it is necessary to open all the cranes available in the design and install the gas lever in the middle position;
  • Press and delay the decompressor until the fuel pumps to the cylinder;
  • Release the decompressor and begin to carefully pull it until he gets into his initial position;
  • Press the decompressor again and at the same moment quickly pull the starter cable.

After starting the unit, it is necessary to give him time for complete heating. This may demand from 5 to 10 minutes. It is fundamentally not to give a motor block to the long high loads, because after the winter its moving details should have time to warm up and be covered with a continuous oilseed film.

How Bind Motoblock Patriot?

To extend the operating time of the Patriot brand motoblocks, it is necessary to refuel them only with scalched 92nd gasoline. It is not recommended to use the 95th fuel, because its quality at many gas stations is even lower than gasoline of the AI-92 brand. Synthetic engine oil for 4-stroke ICE is poured into the motor.

Apart from that, the Patriot brand motoblocks have a container for filling the oil specifically into the air filter of agricultural loads. The containers are placed on which it is necessary to fill the lubricant. The manufacturer does not advise filling the lubricant above the “bath” provided in the container, because the heated liquid will evenly begin to flow into the carburetor of the motor.

Then you can run to run specifically to starting the motor. This will be needed:

  • Install the lever of cool launch in the left position;
  • Translate the fuel feed crane to the “inclusive” position;
  • Set the ignition button to the “Start” position;
  • Slowly pull the starter cable before the resistance;
  • Sharply pull the starter cable on itself. As a result, the engine should start;
  • Give the engine time for warming up;
  • Translate the gas adjustment lever to the position of medium turns;
  • Install the lever of cool launch in the right position.

Main recommendations for common models

Motoblocks in the market are represented from different manufacturers. But, as practice shows, there are several models that domestic consumers trust most and buy them more often:

Accordingly, the launch rules differ. At the Neva motornote factory, such steps should be performed: the transfer of the ignition switch to the ON status, slam the damper (completely) and open the fuel crane; set the gas lever ¾ from the maximum position, pull the starter cable and push the damper.

The motoblocks of the Minsk Plant (MTZ) need a slightly different approach. Gasoline models with a manual starter are trained according to the following scheme: open the fuel crane, set the lever for the launch, turn off the ignition and pump the starter 3-5 times. Then you need to turn the key in the lock and again pull the starter. After starting the lever, the lever is transferred to the working position. Diesel models require pumping (to shake the remaining air), after which you need to sharply twist the starter until the engine starts.

To launch the Urals, you need to resort to such work: set the neutral position of the gearbox lever and open a gas tank. Then you need to completely close the throttle control controller and partially cover the air damper. Then start the engine using the cord.

The launch of the “patriot” implies a different procedure for actions: the removal of the gas lever to the highest position, the jerking cable for purging. First stretching hard and for a long time, then with short jerks to launch the motor, and then regulate the gas handle.

Preparation of the walk.Behind tractor for launch

To study the annotation compiled by the manufacturer, it should be found in order to find out what operating circulation the engine is: four.Stroke or two.Stroke

This is importantly understood, since for modifications with a two.Stroke engine (like a mole cultivator) a special combustible mixture is needed, consisting of a mixture of fuel and oil in a special proportion

Due to the discrepancy between the fuel, the special equipment will make noise, and the candles of the fuse and the fuel pipeline can also suffer, which is fraught with the refusal of the gasoline pump, and this is already a direct way to expensive repairs in one hundred. To establish whether fuel is suitable for motor vehicles, you can by smoke that has appeared. With poor fuel quality, it will have a white tone, as it happens with a strong tilt of the car.

The quality of fuel is also important for a diesel walk.Behind tract. It does not start in the winter. Or starts up, but soon freezes. If the summer diesel fuel is flooded in its motor, since at low temperatures it begins to thicken and clog the fuel stove

Starting of motor vehicles both in the summer season and in winter should be carried out in the established order. For example, to launch the Mole brand motor.Cultivator, this procedure for operations is carried out:

  • Open benzovran;
  • Install the suction engine in a “chock” state (start);
  • Turn off the ignition and twist the engine several times with a hand starter starter;
  • Start the engine again and move the engine to the Run state (work).

Often there are conditions when the power apparatus easily starts, but after a couple of seconds it freezes. In this case, the patency of the sump should be controlled. If the reason is that the tap is littered, then it is cleaned with gasoline.

Starter Motor Diagnosis

Starting motor vehicles with a diesel engine will be somewhat more difficult. The diesel engine is starting with the “fuel” of the fuel path, that is, from the elimination of its accumulations. For this:

  • Open the fuel feed crane;
  • Unwind joints of the outlet channel before the occurrence of fuel;
  • Twist the joints and blow all the nozzles.

The launch of a motor cultivator after winter or prolonged downtime also has its own nuances. In order to bring the unit to the working position, the following manipulations are done:

How to Start an Engine Without A Starter

  • Open benzovran;
  • Conduct a check if food is enabled;
  • Check the availability of lubrication;
  • Give gas up to about half.

Before acting, the motorcycle equipment is checked, including transmission sections, clutch, launch mechanisms, and for need to be adjusted.

Right Launching a walk.Behind tractor after winter

Before starting a motorcycle block after prolonged winter downtime, you need to carefully prepare it. First of all, it is necessary to remove the technique from the garage and inspect it. On the metal surfaces of the agricultural machine there should not be foci of corrosion, the appearance of which can be provoked by high humidity. In the case of corrosion forms, it will need to be removed, treated with a special rust converter and paint areas.

  • Drain the old fuel from the tank, as well as remove the old reducer lubricant. The latter must be thoroughly washed and dried. Then you need to fill in fresh fuel and new transmission oil;
  • Rinse the fuel tubes, make sure that they did not lose their tightness and cracks did not appear on their walls;
  • Remove all filter elements provided for in the design, rinse them thoroughly in clean gasoline, dry and install them back. Damaged filters must be replaced;
  • Remove and disassemble the carburetor, blow it with compressed air or rinse it with gasoline. After that, the completely dry parts of the fuel node must be assembled and installed in place;
  • Check the drive belts-due to high humidity, cracks could appear on their surface-in this case, the elements must be replaced immediately;
  • To disassemble and inspect the CPG of the power unit. If burrs or traces of rust appeared on the walls of the node, then they will need to be removed;
  • To unscrew and check the candle. There should not be traces of scale and tarry deposits on it. Otherwise, the candle needs to be cleaned and dried. After that, the engine ventilation needs to be carried out, several times sharply pulling the starter cable;
  • Check the gap of the ignition system and re.Set it if it was broken;
  • Inspect the controls and make sure that gas and brake cables are stretched as required for work;
  • Remove, recharge and install the battery back if it is provided in the design of the walk.Behind tractor. At the same stage, you need to check the terminals and contacts of the electrical wiring. There should not be traces of oxidation on them;
  • Check the tire pressure and pump them as the instruction to the walk.Behind tractor indicates;
  • Inspect the chassis of the walk.Behind tractor and wrap the weakened bolted mounts;
  • Check the mechanism for connecting a hinged and trailer equipment.

Only after all the listed actions can a walk.Behind tractor be launched.

To start a agricultural machine with a gasoline engine, you need:

  • Fully open the gasoline tap. At the same time, the fuel lever should be located in the “Start” position, and the clutch lever is “disconnected” in the position;
  • Carry out pumping with a manual starter, several times sharply pulling his cable over himself;
  • Translate the ignition lever to the “inclusive” position and pull the starter cable several more times;
  • As soon as the engine of the used walk.Behind tractor is launched, you will need to quickly transfer the fuel lever to the “work” position.

If an electric starter is provided in the gasoline walk.Behind engineer device, then the operator is enough to turn on the ignition and press the engine start button.

Starting a diesel motor unit is a little more difficult.

  • Unscrew the crane designed to supply fuel, gradually promoting each standard connection from it;
  • As soon as the fuel reaches the nozzle, you need to open all the values ​​available in the design and install the gas lever in the middle position;
  • Press and hold the decompressor until the fuel pumps to the cylinder;
  • Release the decompressor and begin to carefully pull it until he stands in his starting position;
  • Press the decompressor again and at the same moment quickly pull the starter cable.

After starting the power unit, you need to give him time for complete heating. It may require this from 5 to 10 minutes. It is important not to give the motorized car with long high loads, since after winter its moving parts should have time to warm up and be covered with a continuous oilseed film.

How to start a motorcycle?

How to start a walk.Behind tractor at the first launch and do not harm the technique? First of all, never ignore reading instructions for. Manufacturers always explain the necessary information in them.

In general, 3 basic rules should adhere to the safe launch of a walk.Behind tractor:

  • Check the reliability of fastening and smoothness of the levers of the fuel system. The course of the cables and levers of gas and clutch should be smooth so that you feel when managing. You should also pay attention to the adjustment of the steering wheel.
  • Check the oil level (in principle, this should be done before each launch). Some models have built.In sensors and with a small amount of lubricant will not be automatically. Other models in this case will be affected.
  • Check the presence of fuel. Refuel the unit only with high.Quality fuel. This will extend the service life of important components of the mechanism and increase the productivity of the work. Pay attention to the type of engine-models with a 2-stroke engine require refueling with a special fuel mixture, the proportions of which are registered in the instructions.

Gasoline and diesel engines have some features that should be taken into account when starting. Gasoline units,

  • Unscrew the fuel supply tap;
  • The suction should be installed in the “launch” mode (choke);
  • Without including ignition, handle the cup starter several times;
  • Turn on the ignition, start the unit and translate the ledge lever to the “work” position (Run).

Motoblock Neva. How to start yourself?

Before the direct launch of the motor, you need to check the oil level in its crankcase. To do this, unscrew the cork of the flood neck located in the front of the power unit. At the end of the traffic jam there is a thread with a thread. If the oil spot reaches this thread, then the lubricant is enough to operate the engine.

To properly start the Neva motorcycle block, you need:

  • Translate the ignition toggle switch to the “inclusive” position;
  • Open a crane for feeding fuel;
  • Close the standard throttle shutter;
  • Set the accelerator lever about 3/4 from the maximum permissible revolutions;
  • Pull the starter cable until the resistance appears;
  • Sharply pull the starter cable on itself. As a result, the motor should start and instantly stall;
  • Slowly open the throttle flap;
  • A few more times to pull the starter cable until the engine starts and began its work at idle.

You can mock the engine of the Neva motor block only when it was idling. Otherwise the risk of failure of the standard magneto will increase.

Motoblocks with an electric steamer can be started immediately after the ignition is turned on.

The process of starting diesel engines is a little more complicated. Before starting, you need to struck the air from the fuel system. To do this, the fuel supply crane opens, the joints of the fuel hose are untwisted until the fuel appears. Unscrew all the taps and transfer the gas to the position at average speeds. Manually pump a decompressor several times. After that, the motorcycle block can be started.

We also offer you to get acquainted with the video on how to properly launch a walk.Behind tractor:

In the case of untimely breakdown of the starter, the walk.Behind tractor can be launched without it.

To do this, you should do the following actions:

  • Remove the starter.
  • Disconnect the launch rope from the starter (or find a suitable new one).
  • In the place of the Starter removed, you will see a round starting head with a hole. Pass the rope through it and securely fasten.
  • Wrap the rope around the part by about half its length.
  • Drown up the rope for launch.

The disadvantages of this method are that with each launch, the rope will have to be reused. The procedure should also be performed in gloves so as not to damage the hand with a rope.

Launching a walk.Behind tractor after winter

Successful launch and operation of the walk.Behind tractor after winter downtime primarily depend on the quality of the fuel and the conditions of storage of the unit in winter. Before the first launch after winter, it is worth changing the oil. After pour into a fuel tank, you need fuel. Having launched a walk.Behind tractor, let him work for a while at idle and warm up. If the walk.Behind tractor refuses to start. Check the integrity of the wiring and contacts, the presence of a spark in the spark plug, blow the fuel system.

Some models of motoblocks have distinctive features when starting.

The launch of the Neva walkover is carried out according to this algorithm:

  • Put the ignition lever to the “ON” position;
  • Cross the air supply and open the gasoline valve;
  • Take the handle of the gas without reaching the maximum;
  • Make a walk.Behind tractor pulling the starter’s cable;
  • Open the air supply damper (in the winter it is better to do it gradually).

Launch of the motoroblock patriot

  • Remove the gas handle to the maximum;
  • Blow the fuel system, pulling the cable required the required number of times. Turn it briefly and sharply for starting;
  • Loosen the gas handle for the desired level.

Launch of the motor unit of the Urals

  • The switching lever should be in a neutral position;
  • Open the fuel supply crane;
  • Cover the throttle, leaving a small clearance. If the engine is cold. Close and air damper;
  • Get the engine.

Clinkles in the muffler

I decided to fix something to reduce the moment when I did it, I decided to get it and that is what happened.) I was just

It is necessary to disassemble and skip the fuel system.

It is necessary to replace or clean the filter.

It is necessary to check the connection of the wires, the engine stop button, remove the spark plug and clean it. Replace if necessary.

Correct launch of a walk.Behind tractor: First, after winter and without a starter

Operation of garden and searry technology begins with its launch. Motoblock is a design that provides a complex fuel system and engine. At this stage, any error can cause a breakdown breakdown, a decrease in its work and the life of operation. Depending on the model of the device, its type of engine and the season, the launch includes its characteristics. Knowledge of basic rules and recommendations will make the start of the walk.Behind tractor high.Quality, and do not damage the unit.

In order to put the equipment into operation, several rules should be fulfilled:

  • Check the amount of oil. Even if when buying it was assured that everything is flooded, you must definitely make sure that the level of technical fluid in the system is sufficient. Some models of motoblocks are equipped with sensors that respond to a lack of oil and simply do not allow to start a motor. But such an option is not characteristic of everyone, there is a technique that can be launched, but this threatens with breakdowns.
  • Refun with fuel. It is necessary to take into account the recommendations to a certain model. Gasoline for some will need to dilute. Proportions are indicated in the instructions for the technique. If a motor block on a diesel engine, then you need to take into account its type according to the time of the year. Summer DT pouring in winter can provoke a driving fuel hoses, which will operate the machine impossible and cause the need to repair.
  • Check and configure the compounds. Clutch, steering, gas. They need to be adjusted so accurately as to ensure the smoothness of switching.

Diagnostics and elimination of breakdowns

To diagnose the starter mechanism, with the aim of the subsequent repair of it, the node must be disassembled. It is easy to do this, only a screwdriver is required. But during this operation, you need to be neat. With careless movements, the spring can fly out and injure the user.

Removal and analysis of the node

The procedure for disassembling the starter is to perform a certain sequence of actions:

First you need to find a screw connecting the starter cover with the pulley, and unscrew it; Then you need to remove the spring, antennae and washers; Then you should carefully remove the pulley, holding the structure away from the face, so that the bounced spring does not injure the user; Next, it is required to inspect the spring: if it is damaged, then you need to put a new one (the cost of such parts is low), and if it jumped out of the hook, it is necessary to return it to its original place, having previously made bends if they have broken off.

Sprinking spring

Spring winding is not an easy procedure. Not everyone gets to install the part on the place the first time, so you should not be upset if it is failure. It is necessary to repeat attempts until the actions are not crowned with success. If you wish, you can watch a video on the Internet, where people’s craftsmen tell in detail and show how to easily and quickly perform this operation.

Important! When winding and installing the spring, you need to remember that it is suppressed, which means that it can burst if you make too much effort. A new part is inexpensive, but you will have to spend time on its search, which means that work on the beard of herbs will move back for an indefinite period

To wind the spring, you need to place the bend in the groove, and then, turning the coil, carefully lay the part along the inner diameter of the bobbin. In this case, the spring must be constantly held with your hands. If it is not fixed, the part slips and pops out, then the winding has to be carried out again. When everything is done correctly, the spring holds tightly in its seat.

Replacement of the cord

The torn trimmer cord must be changed to the rope, you can linen, but without fail suitable in thickness and length. Buy a cord for a starter for a benzocos in this case, buying a specialized store is optional.

To replace the element, in the coil you need to find a hole for it, through which to skip the cord, and then tie the knot. Then you need to take a reel with a spring, having performed several revolutions.

On a note! The exact number of turns can be found by watching the instructions for using the trimmer, or manually. To do this, you need to measure the length of the rope and calculate how many times it can be wrapped around the coil.

For example, if the cord turns around the circle six times, then to pull the spring, you need to turn the coil by the clock six times. After that, it remains only to go through the rope through the hole and fix the handle on the cord.

Other malfunctions

Sometimes after the repair, the spring still flies. You can eliminate such a malfunction with two solutions:

  • So that the bend of the spring does not pop out of the groove, you need to insert a small fragment of the metal plate between the bend and the wall of the seat. This will provide a denser fixation of the spring.
  • Home.Made fastening also helps to keep the spring in the groove. It is necessary to drill holes in the reel on each side of the groove, place the spring bend in them and fix it with a piece of wire. These actions should be performed so that the wire does not touch the starter cover and does not slow down the movement of the pulley.

Collection and installation to the starter place

To assemble a starter and install it on its original place, you need:

  • Turn the pulley with the spring down and place the housing into the case so that the spring bend falls exactly into the groove of the case;
  • Install the puck, then the spring, on top of it. The second washer;
  • Place a cup of antennae on top of the puck and screw the screw.
start, motor, block, starter

When assembly, both goals should be put, otherwise the plastic cup will be damaged by a spring after a while, and when tightening the cord, the user will notice that it was jammed. It will look like a spring has flown. To eliminate such a breakdown, you will need to install a larger screw or another puck. If you find the required details it is not possible, it is enough to loosen a little, after which the starter will stop jamming. However, you need to understand that these are temporary measures, and the malfunction should be fixed as soon as possible.

How to get a motorcycle block correctly?

Motobobes are quite serious and not cheap gardening technique. If you want it to fully fulfill its functions, serve for a long time and reliably, then you need to carefully take care of it and follow all the recommendations prescribed by the manufacturer.

When you bought a technique, it is important to know how to start a motorcycle block. There is a certain sequence of actions consisting of preparing the technique to launch and its direct launch.

Why the motorcycle block works with interruptions?

There are other malfunctions that should be considered:

  • The engine of the walk.Behind tractor hits the return. The reason is often the use of bad fuel. It will not be enough to replace the fuel. Flushing the pump and hoses to supply fuel;
  • The technique works with jerks. The engine does not warm up completely. The motor needs to be drowned, wait for its absolute cooling. After re.Start it and warm it up for at least ten minutes;
  • The engine does not pull, because the power of the motor decreases. The filter system is checked and cleaned. The problem can provoke the wear of the ignition magneto. In this case, the details are replaced.

Owners of technology, both gasoline and diesel type, may face such problems. Regardless of the specifics of the breakdown, you need to urgently stop using the unit and begin to eliminate the problem.

How to start motoblocks of popular brands

On the domestic market, models of various manufacturers are represented, which have their own design features, so the launch of motor vehicles is carried out in different ways. This should not be forgotten, since the wrong procedure can lead to the failure of the equipment and will require serious money for repair.

Let’s see how to start the Neva Motoblock.

Currently, the closed joint.Stock company Red October. Neva produces Neva motor blocks with the power plants of stamps Zongshen, Briggs Stratton and Yamaha.

Consider the procedure for starting these engines separately.

  • Switch the fuel valve to the ON position (VKL).
  • The lever of the air damper should be in the off.
  • Switch the throttle lever to a certain position.
  • Get firmly by the handle of the manual starter and begin to slowly pull the cable until you feel resistance.
  • Pull the starting cord abruptly on yourself.
  • After the engine is launched, the air damper should be slowly transferred to the ON position (VKL).

To launch the brand motor Briggs Stratton:

  • Move the lever of the stop switch to the ON position (VKL).
  • Switch the throttle lever to Fast position (quickly). The engine is controlled only in the FAST position (quickly).
  • Move the air damper control lever to the CLOSED position (closed).
  • Set the fuel feeding to the Open position (openly).
  • Take the handle of the starting cable tightly and slowly pull until you feel resistance.
  • Dramatically pull the starting cord on yourself, the engine should start, otherwise you need to repeat the twitching by the cord.
  • When the engine warms up, move the air damper control lever to the Open position (openly).
  • Turn the fuel valve to the Open/ON (OL) position.
  • Move the air damper to the stop.
  • Turn the throttle in the direction of the ON position (VKL).
  • Set the engine switch to the ON position.
  • Slowly pull the cord starter until you feel the gear gear.
  • Pull sharply by the cord.
  • Return the air damper to its original position and set the throttle in the desired position.

We also recommend reading in more detail about Neva MB-2 motoblocks, this article contains all the most popular models today, as well as which of them is better to choose for purchase and why.

Motoblock Bright

Before starting a walk.Behind tractor, make sure that the clutch is turned off and move the switching lever to the neutral position to avoid a sudden jerk of a walk.Behind tract during engine start. The clutch turns off by clicking on the lever, and turns off by release.

  • Move the fuel tap to the ON position (OB) and make sure that there is no fuel leakage.
  • Close the air damper (lever in the Close position). Do not close the throttle if the engine is warm or the air temperature is high.
  • Move the engine starting switch to the ON position (VKL).
  • Set the gas handle to the full gas position.
  • Small the starter’s handle smoothly until you feel resistance, and then pull it with moderate force.
  • As you warm the motor, gradually move the air damper lever to the ON position (openly).

Now you know how to start a motor.Cultivator Bright.

Motoblock Ural

Before starting, make sure the air filter is completely clean. Be sure to inspect the spark plug, since one of the shortcomings of the technique of this brand is the flow of oil from a separate tank to the engine cylinder.

  • Move the fuel valve handle to the ON position (VKL).
  • To start the cold engine, move the air damper lever to the Closed position (closed). To re.Start the hot engine, leave the air damper lever in the Open position (openly).
  • Put the gas lever (on the engine or on the steering wheel) from the Min (min) position, approximately 1/3 of the course in the direction of the Max position (Max).
  • Transfer the switch (on the engine or on the steering wheel) to the ON position (VKL).
  • Pull the launch of the starter launch cord until you feel significant resistance, then return to its original position, and then pull the handle energetically.
  • After the engine starts and works a bit, transfer the air damper lever to the Open position (openly), and warm the motor at minimum speed for 3-5 minutes.

Motoblock Patriot

Now let’s see how to properly start the motor blocks of the company Patriot. By the way, before starting, check the correct assembly of the cultivator, stretching drive belts and guide rollers, sedatives.

  • Install the switch on the steering wheel to the ON position (VKL);
  • Open the fuel supply crane (transfer the lever to the extreme right position);
  • The lever of the air damper should be in the extreme left position;
  • The gas lever is installed in the middle position;
  • Stretch the starter handle until the resistance appears;
  • With a sharp but not long jerk, pull the trigger on yourself;
  • After the engine warms up, translate the air damper lever to the extreme right position.

Thus, adhering to the rules and recommendations for the launch of the power plant from the manufacturers, you will extend the life of your walk.Behind tract and you can avoid the cultivator breakdown. Also regularly carry out preventive inspections and maintenance of the unit. This will allow timely detecting a slight malfunction and eliminate it in time.

How to get without a starter

In the case when the starter has broken, and there is no time or opportunity to buy a new one, start the walk.Behind tractor as follows:

  • Remove the starting device.
  • Take a device in the form of a piece of cable or linen rope 1.5-2 meters long.
  • Pass the cord into the hole on the element of the walk.Behind tractor, to which the starter was attached.
  • Wrap the rope around, leaving a piece of 45 centimeters freely.
  • At the end of the rope, for convenience, you can attach a small handle, but it is dangerous and can cause damage to the technique.
  • Turn the rope strongly to start the engine.
  • If the launch failed, repeat all the actions again.

Keep in mind that the method is dangerous, and use it only in case of emergency. Do not wrap the rope around the hand so that in case of unforeseen circumstances it does not pinch the engine. If it is possible to postpone the engine to launch before buying a new, working starter. Wait and start the start, according to the rules. Otherwise, you do everything at your own peril and risk.

Launching a walk.Behind tractor after winter

Such machines tend to start poorly after wintering. First of all, the working capacity of the walk.Behind tractor after winter is affected by the conditions for storing equipment in the cold time. If the car winter in a cold and cheese garage, then this can lead to serious problems.

Before the first in the season, it is recommended to change the oil and fuel with the launch of a walk.Behind tractor. It is also necessary to make sure that the operational characteristics of the technical fluids used correspond to the ambient temperature. It is also recommended to read the instructions again to comply with all proportions.

There is a high probability that the motorcycle block will not be started immediately. This is normal, you need to give the details to warm up well. In addition, it is necessary to warm up the motorcycle block and after the engine starts. During the winter, the fuel could thicken, so it is better not to immediately intensively use the machine.

Problems in the ignition system

If there is no spark, as already mentioned, you should carefully check the battery. When everything is in order with him, contacts and the quality of isolation are examined. In many cases, the absence of sparks is associated with clogging the ignition system. If everything is clean there, they look at the contact connecting the main electrode and the cap of the candle. And then they check the electrodes sequentially, evaluating whether there is a gap between them.

A special probe will determine whether this gap corresponds to the recommended value (0.8 mm). Remove the soil accumulated on the insulator and metal details. Check the candle so that there are no oil spots. All of them should be deleted. Pulling out the starter cable, dry the cylinder. If all these steps did not help, you have to change the candles.