How to start a STIHL chainsaw after winter

What happens at the moment of priming fuel with primer, and how it helps to start the saw more efficiently?

At the moment of starting the saw without a primer, several movements of the starter are carried out only so that the fuel pump, under the action of an impulse from the saw crankcase, pumped fuel into the carburetor.

A pump installed in the fuel line allows you to manually pump gasoline into the carburetor without unnecessary movements with the starter. The effect of this action is obvious, the saw will start much faster.

Many owners of gasoline-powered tools mistakenly believe that a hand pump can overly pump fuel into the carburetor and, for this reason, flood the candle. This is fundamentally wrong, since the system is capable of circulating around. Excess gasoline from the carburetor will be directed, through a dedicated hose, back to the tank.

There is no need to use a primer on a hot chainsaw, since there is enough fuel in the carburetor to start.

We start STIHL 180

In order to start the STIHL 180 chainsaw on a cold one, you must follow the algorithm specified by the manufacturer in the instructions for the STIHL 180 chainsaw, namely:

• Turn on the ignition and set the engine control lever to the lowest position (in this position, the air damper of the STIHL 180 carburetor blocks air from the air filter, and the throttle valve is fully open, thus the fuel mixture is enriched);
• Pull the starter handle several times until the first flash passes (the flash signals that the fuel mixture has entered the cylinder and the saw is ready to start);
• Set the control lever one position up from fully lowered (in this position, the air damper opens, and the throttle valve remains in the same position as before);
• Pull starter and start. The saw will start and run at higher rpm due to the throttle valve being as open as possible. To set the damper to idle mode, you must press the gas trigger and immediately release, the tool immediately normalizes the speed.

The STIHL MS 180 chainsaw, as standard, is not equipped with any additional devices that can facilitate starting.

Below you can see how to start STIHL 180. The video reflects in detail all the main points, and the author’s Комментарии и мнения владельцев allow you to understand the whole process to the smallest detail.

We start STIHL MS 211 C-BE

The fuel supply system in the STIHL MS 211 C-BE chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold.

The instruction for starting this model of the STIHL chainsaw contains one additional point, which is that before starting the chainsaw on a cold one, it is necessary to pump fuel into the carburetor using a pump. Further, the instruction does not differ from starting STIHL 180 and follows the same algorithm.

Getting Started STIHL MS 180 C

The device of this model, in comparison with the previous one, has some differences in the trigger mechanism, but it does not carry any changes in the triggering algorithm. The fact is that the ErgoStart system is installed in the STIHL 180 C, which, due to an additional spring installed in the chainsaw starter, reduces the engine resistance when starting.

How to start a STIHL chainsaw

All STIHL chainsaws are equipped with two-stroke engines, the cold start of which has a similar algorithm. But there are models on which additional equipment is installed, allowing you to start the saw without excessive efforts. For this reason, the algorithm for starting them may differ slightly.

Let’s take a look at how to start a regular saw and how the process differs from starting a modified model.

How to start a chainsaws with a decompression valve

Before starting a STIHL chainsaw with a decompression valve, you must turn it on. It should be noted that there is no decompression valve on the STIHL 250 saw.

After the first flash has passed, the valve will be set to normal operation, respectively, after the engine control lever is set to the open air damper position and starting continues, the decompression valve must be pressed again.

The valve operation is schematically shown in the figure below.

In fact, the valve does not make starting faster, it just simplifies the process and makes it more comfortable, because for during launch, a person will have to apply significantly less effort.

A saw with a decompression valve, whether the engine is cold or hot, must be started using the valve to relieve the cranking force of the engine. This will significantly increase the service life of the starter and reduce the number of torn laces, since it is installed on chainsaws with a large cylinder volume and, accordingly, compression.

How to start the saw after long periods of inactivity

I can’t start the chainsaw after a long period of inactivity. Such Комментарии и мнения владельцев can be found on the forums dedicated to the repair and operation of saws. Let’s figure out how to start a chainsaw after a long period of inactivity.

The fact is that a successful start after downtime must be taken care of in advance and the saw should be properly prepared for storage. According to the manufacturer’s instructions, before storing, it is necessary to drain the fuel from the tank, then start the engine and burn off the fuel in the fuel system.

Preparation is necessary so that during storage, the carburetor membranes do not stick together. Performing this simple operation will allow you to successfully start the saw after long-term storage.

It is much easier to start the chainsaw six months after idle time, if just before starting, through the spark plug hole, add 1. 2 ml of the fuel mixture to the cylinder. This can be done with a syringe.

Starting a STIHL chainsaw almost always follows the same algorithm, except for those cases when a decompression valve and a fuel primer are additionally installed on the chainsaw. These gadgets are designed to facilitate the start-up process and do an excellent job of their functions.

General rules for using a chainsaw

The basic rules for operating the tool are the same for all brands. STIHL 180, Echo, Ural, and they are as follows:

Getting a chainsaw running again after its been sitting for years

• The saw must be held with both hands, grasping the handle with all fingers.
• The employee should not be directly behind the chainsaw, but to the side of it.
• Use the top or bottom edge of the tool to cut the material.
• If you need to move to another location, for safety reasons, turn off the engine.
• You need to start sawing with that part of the bar that is located closer to the body.
• The employee must wear special clothing, boots with protective inserts and use personal protective equipment. glasses, durable gloves, a helmet.

How to start a new chainsaw?

Before starting a new chainsaw, clean it of the preservative, check the complete set, the reliability of the fasteners tightening, and the chain tension. Before intensive use, the tool must be run in. This should be done not at idle, but at low load, which will avoid rapid engine wear.

The start of the tool is carried out using a starter, which in many models is connected to an inertial or spring-type light start system. With correct adjustment of this mechanism, the force applied to start the motor is almost halved.

To extend the operating life of the starting device, you should work out a smooth movement, in which high loads will not be created.

Chapter 9: Starting Your STIHL Chainsaw

The first launch is performed in this order:

• The equipment should be filled with fuel and lubricants, placed on a flat, stable surface, unlocked the protection mechanism against accidental start-up and emergency stop.
• To start the engine, the throttle lever is set to the low rpm position. With a smooth movement, you need to pull the starter, with the other hand. hold the tool. As a rule, a new saw in a technically sound condition starts up from the third. fourth time.
• At idle, the crank mechanism operates under conditions of oil shortage, so this time should be minimized.

At the factory, the carburetor is adjusted according to average parameters. Therefore, they are brought to optimal values ​​already during the operation of the chainsaw. The motor must work without interruptions, not emit extraneous noise. For a full lapping of all systems and parts, moderate loads are used.

How to start a chainsaw correctly?

Chainsaws can be started in different ways, depending on the model and technical condition. Today we will look at how to start a chainsaw without a starter, what to do if the tool has not been used for a long time. In any case, before using the tool, you should carefully study the instructions, follow the operation and safety rules.

How to start the tool after a long period of inactivity?

After long-term storage, you may encounter some problems when starting the motor. The first thing to do is to make sure that the equipment is in good working order, there is a spark, fuel, and there are no wire breaks.

If the saw is in good working order, its launch is in progress:

• turn the fuel cock to open;
• press the enrichment button, which will fill the carburetor with fuel;
• turn the lever and completely close the air damper;
• start the engine with the starter. press the throttle handle, smoothly, without sudden jerks, pull the cord, turning the crankshaft.
• after a flash of a combustible mixture, open the air damper and continue starting the engine.

What to do if the chainsaw won’t start. ways to eliminate

So, if, in fact, when the chainsaw does not start, the reasons were found out, you can start to eliminate them, of course, if you have the appropriate knowledge and practical skills to access gasoline. According to the identified causes, the first actions in the event of a saw breakage can be carried out on site or in a specialized workshop. So, methods for eliminating defects have also been established, the first of which may be:

• Replacing the starter if the reasons for the absence of the saw product are contained in a critical condition of this component.
• Inspection of the entire ignition system, up to candles for defects or wear, especially if there is a spark at the factory, and the tool still does not want to start, apparently through drying out of the candles.
• If there is no start of the chainsaw to a cold system, most likely: the piston group has been destabilized, there are no mating contacts, the fuel and lubricants do not match the consistency.
• The chainsaw does not start on hot due to worn out oil seals and other elements, due to high output.

Chainsaw STIHL 180, Partner and others will not start

In the world of chainsaws, the number of models distinguished by speed, overall, consumable and other parameters is almost limitless. But regardless of the technical potential and cost, each saw comes to the point of production when various elements exhaust their working resource. A variant of the manifestation of a breakdown is the case when the chainsaw does not start with any attempt at this action. At the same time, the plant may initially work once, then less often, or the STIHL 180 stopped starting instantly. In some cases, each chainsaw can be characterized in different ways by the appearance of this ailment:

• a gas powered tool spark or its technical protégé from the Goodluck line does not start after prolonged lying without action;
• an old Husqvarna stopped starting in the middle of work;
• a Partner gasoline saw or Friendship, which has long been known for its popularity, does not turn on after a prolonged load;
• saw model Motor Sich 270 does not start immediately, but after another attempt it stalls with low operating mileage;
• chainsaw Ural does not want to start after self-maintenance.

Why the chainsaw does not start well and stalls. main reasons

There may be completely different factors among the reasons when the chainsaw starts and stalls or even refuses to be brought into working condition. In this case, attempts to understand through what and why she does not want to start should be carried out from sober reasoning of the appearance of this nuance. As a result, we have a set of relationships:

• The chainsaw does not start well due to wear on the starter system.
• Overheating of the mechanisms has occurred, which affects the Chinese low-performance gasoline saw more
• There is no way to start, as the candle is dry or damaged;
• The tool did not work for a long time, for example, if it is impossible to start after winter without using the saw for its intended purpose.

It also happens when the chainsaw simply stalled for no obvious reason, not wanting to start, so that it would not be done by the user. In this case, to determine the cause, it is better to contact a KosiKosa specialist who will conduct the necessary testing and, if necessary, carry out repairs, as well as suggest elements to improve performance. This can be a good chain for a chainsaw inexpensively or spare parts instead of broken ones. links of the ignition system.

Chainsaw repair and basic chainsaw parts at Kosi Kosa

For the repair of gasoline saws, when there is a malfunction due to the lack of starting, the assortment of “KosiKosa” includes a variety of spare parts, such as starter rings, springs, clutch elements and others. The high quality of each of them and compliance with the model range of gasoline-powered tools allows you to make repairs immediately after the inability to start the saw. Turning to us, the mother will clearly describe the cause of the breakdown and select the right action. For example, if a candle is wet on an inoperative tool, then it will be necessary not only to replace it, but to remove the reason why it floods the candle and blocks the start. In the hands of KosiKos specialists, each chain saw will start a new life, regardless of whether it is a new saw under warranty or has been in operation for a decent period of time.

Algorithm for setting the saw “STIHL 180

If you are faced with the question of how to start a STIHL chainsaw, then this process can be considered using the model 180 as an example. In order to carry out work on a cold one, you must turn on the ignition and set the engine control lever to the lower position. In this case, the carburetor flap will block the air from the filter, and the throttle will be open, so the fuel mixture will be enriched.

The starter handle must be pulled several times until the first flash occurs. This will indicate that the mixture has entered the cylinder and the equipment is ready for institution. Before starting the STIHL chainsaw, you must move the control lever up one position. In this case, the air damper will open, while the throttle will remain in the same position.

The starter must be pulled and started. The tool will run at increased speed and the throttle valve will be open. To set the latter in idle speed, you must use the gas trigger and release it. In this case, the tool should start working normally. On the described model of the chainsaw there are no additional devices that would make it easier to start.

STIHL 250 chainsaw review

You can buy the 250 model at a price of 29,542 rubles. This equipment is a semi-professional model with a 40 cm tire. Power is 3.1 liters. from. or 2.3 kW. Fuel tank capacity is 0.47 l.

Quite often, consumers are wondering how to start a STIHL 250 chainsaw before buying. This was discussed above. However, this information is not the only one that should be read before using the model. Among other features, it should be highlighted:

• single-lever control;
• the presence of a compensator;
• anti-vibration system;
• side chain tensioner.

By purchasing this model, you will be able to carry out its quick refueling. This feature is realized by the lid, which has a patented design. The operator, when working with the equipment, will have reliable hand protection. Consumers especially highlight the notch bumper, as well as the chain, which guarantees high-quality and fast cutting of wood.

Starting a Stihl Chainsaw the correct way. NEVER flood it Again!

We start the saw brand MS 211 C-BE

If you, too, were among those consumers who thought about the question of how to start a STIHL chainsaw, then as an example, consider another model that was mentioned above. In it, the feed system is equipped with a hand pump, which makes it easier to start the saw on a cold.

The instruction contains an additional paragraph, which indicates that before starting with the pump, it is necessary to pump fuel into the carburetor. Next, you should proceed according to the principle that was described for the 180 model.

Tips for starting a saw MS 180 C

This device, in comparison with the previous one, has some differences in the trigger mechanism. However, there will be no changes in the startup algorithm. The equipment described has a system that uses a spring in the saw starter to reduce the resistance of the motor.

Saw installation with decompression valve

Users sometimes ask how to launch when the instrument has a decompression valve. There is none on the 250 model. As soon as the first flash occurs, the valve will be in normal operation. The engine control lever will be set when the choke is open. Start-up will continue and the decompression valve must be pressed again. It does not make the start-up fast, but it simplifies the process and makes it comfortable, because during the start-up the operator will have to put less effort.

If you are not entirely sure that you know how to start a STIHL 180 chainsaw, then remember that equipment with a valve, regardless of whether it has a hot or cold engine, must be started using the valve. This will help ease the effort to crank the engine. So you can extend the life of the starter and reduce the number of torn laces, because these chainsaws have a larger cylinder volume and compression.

Setting up the saw after winter

Before storing it, you should drain the fuel, and then start the engine and burn off the fuel that remains in the system. Preparation is necessary so that the membranes do not stick together during storage. This simple operation will allow you to start the saw after winter. If you still do not know how to properly start the STIHL 180 chainsaw, then you should know that it will be easier to do this if you add 2 ml of fuel mixture to the cylinder through the plug hole before starting. This can be done with a syringe.

Chainsaw MC 180 review

This model of equipment costs 11,490 rubles. It is a household tool that will help you cope with work at a summer cottage. With the help of the machine, you can get rid of unnecessary twigs and cut down small trees. The control is single-lever, and due to its low weight, it is very comfortable to work with the unit.

The consumer should be aware not only of how to start the STIHL ms 180 chainsaw, but also of the technical characteristics. Among others, the 35-cm tire should be distinguished, as well as the engine, the volume of which is 31.8 cm 3. The volume of the oil tank is 0.15 liters. The equipment weighs 3.9 kg. The power of the model is 2 liters. from. Fuel tank capacity is 0.25 l.