How to stuck a steel rivet with a hammer. Grandfather’s method how to establish a threaded…

How to rivet steel rivets

Rivets are a fastener system that is used to connect two or more parts. They are inserted into pre.made holes in the blanks, compiled in one fishing line for a trimmer. The fasteners are a round rod, which, as a result of deformation, tightly covers the walls of the holes and is held in them due to the friction force.

The main properties of rivets

The rivet gives a more reliable connection than a screw or screw. At the same time, it occupies a minimum of space, not protruding from the workpiece with a large head, which occurs at the bolts. The main advantage of such fasteners in its low cost and high installation rate. Rivets are used in cases where the workpieces are not planned to be disconnected. Having planted a rivet, it is already impossible to disassemble the connection without sparkling.

An important advantage of using rivets is their resistance to vibration. If, for example, a threaded connection with a constant shake can weaken, since the screws, nuts or bolts are promoted, then the rivet does not have such a lack. It is tightly planted and no longer comes out. In the event that a large mechanical load on the gap or cut is on the connection, then the riveting metal can only break, or damage the parts themselves, but it will not work out just like that.

Rivets are a popular connecting element, so it is not surprising that they are offered in a rather extensive assortment. All existing structures can be divided into two groups. cold and hot riveting. Cold is made of softer and plastic metals, which are relatively easily deformed, taking the required shape. A hot.type rivet is made of solid steel, therefore, as a result of the pressure created, it practically does not change its shape without preliminary warming up. It provides a more reliable connection, but it can not always be applied. This type is used in cases where the heating does not hurt the details. In particular, such fasteners are used in shipbuilding and machine tools.

Varieties of rivets

There are quite a few varieties of rivets. Each of them has its advantages and is intended for use in certain cases. Fasteners differ not only in the installation method, but also with a load that can withstand.

In addition to the classification of rivets by the temperature of their installation, they are also divided into three groups according to structural features:

Each variety is intended for a specific purpose, so to say that some group cannot be better.

Ordinary

Ordinary ones appeared the very first. They are easy to recognize because they have the shape of a mushroom. Their metal rod is decorated with a wide hat. Such rivets are considered one of the most durable, but difficult to install. This type of fastener can only be used if the connection of two elements is required with the possibility of installing riveting through them. That is, the fungus should remain from one end of the connection, and the main rod of fasteners should go out of the road for at least a few millimeters.

In order to combine two blanks, it is necessary to rest a solid metal object on the rivet hat and soft blows along its rod flatten the material by forming a semblance of an existing head. Thus, a strong connection is ensured not only by internal friction in the holes, but also by the external press, which is created between the factory and the created hat.

Exhaust

Exhaust rivets are used in cases where it is necessary to connect two metal sheets. They allow for reliable fixation of the workpieces, even when there is access only to one side. A special pneumatic or mechanical type pistol is used to work with them. There are also nozzles for electric screwdrivers, which also allow you to work with such fasteners. The rivet itself is a long metal rod, at the end of which there is an aluminum tube sleeve. Another soft metal can also be used.

When stretching the steel rod, the sleeve is deformed, because at its end there is a small hat that does not allow it to go out. As a result of the created pressure, the sleeve fits tightly to the entire surface of the hole. In order to conduct a high.quality connection, it is necessary to rest the end of the rivet gun to the connected parts. This is the key to success. Directly the tail of steel itself, which is drawn by a gun, can be broken down, since it has special notches to weaken strength, or completely leaves the sleeve.

The exhaust type of rivets is most often used, since it provides easy installation, and the pistol for work is relatively cheap. An important advantage in favor of such fasteners is the fact that it can combine a thin and thick part, even if the height of the sleeve is less than the total thickness of the blanks. Just inserting the rivet and starting to tighten the tail, you can create quite sufficient deformation to achieve high friction necessary for fixing parts. Of course, the reliability of such a compound will not be as high as when using a full.fledged through installation.

Threaded

Threaded rivet is the most expensive. The fastener itself is a half sleeve, inside which the thread is cut. The sleeve is directly inserted into the prepared hole of the connected parts, after which the rod is twisted inside. After that, it breaks towards the supporting surface from which he is twisted. In this case, the sleeve begins to crush, as in the case of exhaust. As soon as the required quality of the connection is achieved, the rod is simply turned out.

Such sleeves are usually made of aluminum, but there are copper and brass. The main drawback of such fasteners in its high cost. Also, in order to achieve a quality connection, it is important to observe the direction of pulling the rod under 90 degrees. In this regard, the work is best done using a special pistol, but it is quite possible to do with a bolt and nut.

What is a riveper and its types

The rivet is a special tool (ticks) operating on the principle of a gun, which is designed to connect structural elements and their individual parts, when their thickness does not exceed 10 mm.

Basically, with the help of such a mechanical pistol, parts from the inside are fixed. A manual riveper represents a lever tool in the form of a gun consisting of 2 parts:

Today there are two types of rivets on sale: threaded and exhaust.

Hand.shaped light.type tint works on the basis of using a traction force to fix rivets. Under the influence of the effort of the lever, the rod rod is drawn into its tubular part and bursts it with the head of the rod. From the outside, the rivet hat is also flattened and creates a strong fixing of the parts.

The principle of operation of the manual rivet of the threaded type is the same, only pulling the ball in the working part does not occur due to effort, but by rotating the thread in the tubular part of the riveting. That is, it uses a method of fixing the head by tightening the handle. This method is not used often and is mainly necessary to fix parts with a small thickness.

Completely with a gun, nozzles of different diameters and tail length are usually sold.

Watch the video review of the threaded riveter:

Types of rivets

There are not many varieties of rivets as it might seem at first glance:

• Simple general.purpose rivet according to GOST 10299 80. They are easy to distinguish in a mushroom form, also called a system with a closing head. Such a rivet is characterized by high strength and resistance at any load;
• The rivet is exhaust, used to “sew” two sheets of metal in cases where access to the connected sheets is possible only on one side. The parameters and description are determined by GOST 15973-2005;
• The most technologically advised threaded rivets, they are more convenient to work and allow you to create a collapsible connection, DIN 7338.

Important ! Materials for the rivet connection must have a certain plasticity and viscosity, therefore, low.carbon steel, copper, aluminum deformable alloys are used for their manufacture.

Rivets with a secret head

Similar elements have other names. shock, clogging. Riveting with this part is carried out in several cases:

Rivets can be overlapping, in the way, as well as chain and chess method.

about rivets for a hammer, watch in the video below.

Rolling is one of the simplest types of fasteners to create non.incompatible compounds. In the general case, it is a rod or tubular part, which has at one end the supporting “embedded” head of a certain shape. It is installed in the connection, as the name implies, by the method of scruffy (as well as shrinkage, roller rollers, broach, explosion).

By the shape of the riveting, you can conditionally divide into several main types:

• Rolling with a closing head (there are full.bodied, hollow and semi.empty)
• Rivets with a length (also called. tear.off or exhaust)
• Ribs rivets (also called. riveting nuts)

Closing a cloth

Historically, rivets with a closing head were historically invented. therefore, they were most widespread. Such rivets have a mortgage head on one side. The second head, called the closing, is formed using a roller or riveting tool: cloth hammer, ticks.

In the shape of the head of the riveting head with a closing head are divided into:

Also constructively, they differ in the presence of a hole inside the riveting:

• Full.bodied rivets. the hole is missing
• Hollow rivets. tubular. have a through hole
• Semi.empty rivets. under the collapse. have a dull hole

Materials for rivets

Rolling with a closing head can be made of a variety of metals and alloys, which are well lended on plastic deformation.

The following materials are most widely used:

• Steel. mainly plastic high.boiled steel 03kp, 05kp, 08kp, 10 kp, 15kp, 20kp
• Stainless steels. austenitic steel 12x18N9, 08x18N10, 03x18N11, 12x18N10T
• Aluminum alloys are the most applicable alloys of blood pressure, AD1, aluminum-magnesium alloys AMG2, AMG5, AMG5P, AMG6, alloys of the AMC, B94, B65, also use duralumin alloys D1, D16, D16T, D18, D18P, D19P, D19P
• Brass alloys. mainly the alloy L63
• Copper. brands MT, m3

Marking of rivets based on materials

Rolls can be marked on the head. for subsequent identification. Marking can be convex or concave (branding).

The following is a table with the marking of the main materials in the form of points or strokes.

How to work with a riveper correctly?

In this article we will talk about a tool with which it is comfortable to work in a limited space.

Hamper is a hand tool with which you can fix the necessary material. For example, metal sheets.

In this article, we will consider the types of this tool and note a couple of moments that will come in handy when working with it.

As a result, we will receive a small instruction for those who have not yet had to deal with the riveter.

From a brief description, it becomes clear that we will need this tool in the case when you need to fasten something. In this case, the material should not exceed a thickness of 10 mm. This is one of the basic rules.

There are cases when this is not possible.

Do not use welding at home, and there is a chance that there is no need for the right equipment at hand.

But the tool that resembles ticks is perfect for the quick implementation of your project.

What does it consist of?

He does not have many constituent elements, but this does not interfere with the riveter to perform all the necessary functions. For him, you need to highlight a separate place in your organizer for tools.

Only three elements that provide rapid fastening of the metal sheets we need.

The mechanism, by the way, is divided into two types: exhaust and threaded.

What types are?

Electric, battery, pneumatic.

However, they are not as popular as manual. The case is at an inflated price. And although they, in fact, do all the work for you, buyers are still not ready to completely switch to an electrician.

Manual riveter is more understandable for people. It is easy to use and is available in its cost.

The first three types are more suitable for avid specialists.

Or in the case when rivets of large diameter go into business.

Exhaust rivet.

Cylindrical stilett. Here is the difference.

It is worth noting that this is a division according to the type of rivets used, the mechanism of work, and not by distinctive characteristics.

The holes with it will be closed completely. It should also be noted the low cost.

Consolidation occurs through traction force.

Openings are first made, and then the rivet is fixed.

Threaded rivet.

With it you can provide safe installation.

It consolidates qualitatively. You can also create mounting points. It’s comfortable.

This tool can be distinguished by the number of handles. It is one.handed and two.handed.

In the first case, one of the handles always remains motionless. Such a rivet can be used for connections with a diameter of not more than 6 mm.

In two.handed, as we see, both pens remain mobile.

Different types of this tool work approximately the same. The principle is similar, but there are still differences.

Let’s start our instructions with the main (general) principle of work.

• It is necessary to direct force to the lever mechanism, after which it will go to the head.
• We cook in advance. A hole for the element. And then insert the riveting with the help of a clamping mechanism.

This ensures leaf metal fastening.

All forces must be directed to make holes. Everything else will make a tool for you.

Denote all types of work that the rivet performs.

It can fix the corners, pipes, fix the profiled sheets.

Such fastenings have never questioned their reliability. And they will not burst when you do not expect this. This is a fairly urgent problem for welding.

The main principle was discussed, and now about the stages of work.

• We take materials (metal sheets) that we need and prematurely fix them. This will facilitate the work.
• We make a hole that should be more than a rivet for 1-2 cm.
• Insert the consumable.
• We twist the head of the rivet.
• We plant the tool tightly to the base of the material, and then compress the handle.
• Repeat several times if it did not work out.
• For complete tightness, we use additional special materials. Most often use putty.

You need to pay attention to the characteristics of the tool, materials and appearance. Even weight can say a lot.

If you buy through the online store and there is no way to see and touch everything in detail, then pay attention to the hollow body. The characteristic of the goods will indicate the material from which it is made. Plastic here is not the best option.

We conclude that working with a manual riveter is not so difficult. This is a simple option that can easily be stored in the house.

But if you are engaged in repair and installation, as well as locksmithing, then it will be better to purchase a threaded type tool.

Hamper is not a hammer. Why will it need?

Do not underestimate this small tool. Here are a couple of ideas that you can use when a threaded rivet was lying around at hand.

• Installation of doors, windows, shelves, anything.
• Fastening of decor items: paintings, signs on the door, anything.
• Installation of furniture handles, for example, for drawers and cabinets.
• Installation of window blinds, suspended hooks, etc.D.
• Of course, auto repair.

In this article, we got acquainted with different types of rivets, made out their differences and made up a brief instruction on the use of a hand tool.

If you still have questions, then we advise you for clarity to watch a couple of videos on the use of a riveter.

The use of rivets

The choice of specific parameters and varieties of fasteners is determined by three main criteria:

• Ensuring the necessary strength strength, taking into account additional parameters and seam requirements;
• Technological capabilities of equipment for working with a specific type of rivet connection;
• Economic feasibility of using riveted compound;

Threaded nuts-clicks

The method of connection using threaded rivets can be called the most universal today. The main idea of ​​the connection is the witty idea of ​​fixing the body of the rivet in the riveted hole. For these purposes, a rivet for threaded rivets is used. The threaded structure itself is a half.liner with internal thread.

When performing the connection, this sleeve is inserted into a drilled hole and is aligned so that the united parts are tightly adjacent to each other. After that, the rifle rod is screwed into the threaded hole inside the workpiece. The front wall of the sleeve is fixed by the supporting surface of the tool, preventing the rivet from leaving the hole. To plug the sleeve, the rod of the rivet moves with great effort towards the supporting surface. The sleeve is crushed and besieged, thereby forming a strong motionless connection.

The rod of the riveper is freely wrapped from the body of the sleeve. Most often used rivets aluminum, brass or copper. The use of the latter is limited by high cost, so they are established in cases where it is necessary to provide good electrical contact between the cooked surfaces.

The advantages of a threaded rivet connection include its “low.traumatic”. When the rifle rod is operating, the connected metal does not experience large loads or deformations. A threaded sleeve is easy to connect a thin.walled metal or a profile of complex configuration. Such fasteners are widely used in the assembly of household appliances, in the combination of individual components of car facing, in the manufacture of various kinds of structures from corrugated board.

Exhaust rivets

The disadvantage of the threaded types of riveting is their high cost and a relatively low speed of the compounds. Therefore, for cases when the connected sheets of metal, profiles are required to be connected using several hundred or thousands of points, the exhaust type of rivet is used.

It can be steel, brass metizes, rivets made of aluminum, aluminum alloys and silicon. Unlike a threaded, in an exhaust scheme, the deformation of the sleeve is carried out using a rod with a thickening at the end, pressed into the body of the fastener. As in the previous case, in order to besiege the body of the rivets, its end is rested on the supporting surface of the rivet, after alignment the central rod is pulled out with an effort to several millimeters. As a result of the walls of the sleeve, they are deformed, forming a fairly strong unwritten connection. The shank of the rod is most often broken off or trimmed along the level of cutting of the sleeve.

Note ! The exhaust circuit provides a very good riveting speed of the metal.

Shock mandrels for riveting hammer

By the type of rivets, shock mandrels (they are also called a drummer or fight) can be carried out for two types. Marking mandrels with a semicircular head and mandrels for rivets with a secret or flat head. Of course, there are special types of mandrels, for example, corner mandrels for installing rivets at an angle, but such things are rare and are used in special cases. Mandrels for rivets with a secret head or “nickle” are considered universal. It is suitable for rivets with a flat and hidden head of any size. The choice of mandrels for installing rivets with a semicircular head should be approached more responsibly. For each rivet diameter, a shock mandrel of the corresponding size will be needed and to obtain a high.quality connection, it is important to observe this order.

The end springs, in turn, are used to hold the shock mandrel in the trunk of a cloth hammer. Springs are consumables, because over time they have the ability to stretch. Think about this when ordering a tool. it makes sense to immediately take a spring in reserve. Two types of end springs are found. The straight spring has the shape of a cylinder and is a universal. It serves to hold shock mandrels, both for rivets with a secret head, and for rivets with a semicircular head. The conical end spring has the shape of a cone and serves to hold the mandrels only for rivets with a semicircular head. The straight spring is slightly weaker and usually becomes unusable a little faster, so we recommend leaving it with secret rivets, especially since most often the supply of cloth pneumatic hammers includes springs of both types.

The choice of riveting hammer

Now that there is an understanding of what the working range of the cloth of the cloth depends on, you can make a choice by starting from your technical specifications. Here are a few points that you should pay attention to:

The easiest way to focus on the working range indicated by the manufacturer. The factory has already calculated everything for us and indicated in the specification of the product for which size rivets (the maximum value is usually indicated) this tool is intended. Be careful, most often, the working range is indicated for all.metal rivets from aluminum. If you plan to put steel rivets, you should take a tool with parameters one step more. For example, if the documentation states that the tool works with aluminum rivets up to 4.8 mm, which means it will work up to 4 mm on steel.

Another thing is if you have the opportunity to test the tool before buying. For the installation of one riveting, about 3-5 seconds of the riveting hammer should be enough, no more. Too big shock impulse can damage and/or deform the working surface. At the same time, too weak the impulse will not allow to fully set the rivet, and the prolonged effect on the working surface will also negatively affect the structure of the connected materials. Pay attention to this when choosing an airmaker. Take the tool with such characteristics (piston diameter and barrel length) so that the effort is enough to set the rivet in the specified period of time.

As we have already learned, an important role in the working process is played by shock mandrel. The size of the mandrel is selected for the diameter of the riveting. Specify, what size mandrels are included in the set of your tool and if the right size is absent, order it additionally. Using the mirror of the wrong size, you risk obtaining a poorly connection. The fact is that the working surface of the mandrel under the rivet with a semicircular head has the shape of a dome, which completely repeats the geometry of the rivet head. Thus, in the process of installing the riveting, the shape of its head is not deformed and at the output we get a beautiful riveting seam with even and neat semicircular heads. If you take the mandrel less, the rivet head will be deformed. If there is more mandrel, there is a risk of damage to the working surface around the rivet, and this is already a marriage.

Principle of operation

How to use a riveper is perhaps the most important question that is interested in the master. In order to create a reliable connection, during its execution it is necessary to adhere to the next algorithm of actions:

At the first stage, it is necessary to align the surfaces well so that you can provide the most dense contact between the details.

Starting to drill holes, it is necessary to ensure that they are located strictly along the same line. To properly perform this operation, the surface is recommended to be placed on a flat plane, for example, a wooden workpiece to which they should be fixed. After that they proceed to applying the location of future holes. Further, they begin to make holes, making sure that on each detail they are located exactly in the designated places.

An important task is to ensure the correspondence of the size of the opening of the required parameters. To do this, it is recommended to take a drill of slightly larger diameter. For example, if you create a hole with a diameter of 3.8 mm, you should use a drill with a diameter of 4 mm.

When the holes are ready, be sure to “try on” prepared fasteners. If everything is done correctly, then the head of the rivet will be tightly adjacent to the surface in the edge of the hole and completely close it.

At the final stage, rivets are installed, adhering to the following order:

• First, the cylindrical body of the rivet must be placed in the made hole of the connected elements.
• With the help of a riveter, you need to capture the rod passing through the entire body, and it should be fixed with the lips or the riveting head of the tool directly at the base of the cylinder head.
• When putting the necessary effort on the rod, it must be pulled through the groove body, while expanding it with a hat and deforming the end of the cylinder. As a result, you should have a reverse wide part of the rivet on the inner part of the connected elements.
• Having selected the necessary effort for the rivet, the parts are reliably connected, after which you only have to break off the protruding parts of the elongated rod.

In most cases, when using a manual riveper, you have to press the lever several times to achieve the necessary result. After connecting the elements on one side of it, the head of the body of the rivet will be located, and on the other. the flattened end of the cylinder, which looks like a group of petals.

Recommendations for the choice of tools

Today, stores offer many varieties of manual rivets, which can be purchased at a price of about 2-3 tons. R. To select the most suitable model, you must first understand for what purposes you need a tool. If you decide to purchase it for a frequent connection of different elements of parts, we advise you to opt for a more expensive professional tool. All the rest will be quite enough and the budget model, which will cost it about 150-500 r.

If you want the tool to serve you for a long time, you should not only know how to choose a manual bracket, but also observe accuracy while using it. Otherwise, it will quickly break in your hands, even if it is an expensive professional tool from a well.known brand.

Price is one of the important factors that should be considered when choosing this device. But besides him, other characteristics are of no small importance:

• Material of rivets. You can buy any of the tools available in stores to connect aluminum parts. If you have to fix steel details, we advise you to make a choice in favor of more powerful rivets.
• Ease of use. If you plan to use fasteners of different diameters and from different material to connect, then it makes sense to purchase a two.handed model. When choosing an instrument, we advise you to pay attention to his head. It is desirable that she be a turning point. Then you can easily perform the connection in complex areas. Before buying, it will not hurt to find out if there is a set of interchangeable nozzles in the configuration. This is especially worth worrying about those who are going to use different fasteners to connect.
• An important characteristic that must be taken into account when choosing a riveter is the presence of a container for waste. It will be especially indispensable to those masters who are going to build a fence on the territory or lay a roof.

Sexual post Part 2 or body repair with minimal money (and only it, but not time)

Being unable to spend about 30,000 on a sane welding semiautomatic device, I wondered how else you can fasten body elements?

There are actually a lot of options for fastening body parts: 1. Welding inverter. He refused to weld the body of the inverter after several unsuccessful attempts to cook thin metal among themselves, even with an electrode of 2mm, and you won’t have time to blink an eye with an eye with an eye as a good metal, so you had to throw it, to edifying future generations: the welding inverter, well will not help you in body repair, if you want to cook the body, then take the semiautomatic device, do not have in vain hopes that you can fill your hand and inverter to cook the body.2. Point welding is a difficult and not always affordable welding option in garage conditions, you can make such a device from the inverter, but it is unlikely that it will be used in place. Yes, and not for all welding conditions, this is suitable, for example, you can’t weld it, but you can only cook overlap, again a bunch of settings of the duration and strength of the pulse Not option3. A semi.automatic from an inverter. do not waste time, briefly, the moral of the fable is such that the inverter is a current source, and a semiautomatic device is a voltage source, completely different principles and ideology of the welding process, even if you can hold the arc, it will be an unstable and unreoned welding process4. Tig welding from an inverter. there are such welders with a function of tig, my one of these is generally realized, but in my small garage hold a cylinder for 40 liters with an argon well, completely reluctance, and taking into account the cost of a burner and a gearbox and a cylinder (5,000 1500 2500 = 9,000), for welding small volumes of fine metal, it can quite replace a semiautomatic device, but a cylinder:-((in general, the most universal method of welding, you can cook anything, but in speed it is inferior to a semi-automatic.5. A bolt connection is a good way to connect metals, but the minus is only that the bolts’ hats will protrude very far out, which can have a negative impact on the functionality of the final workpiece. But there is a huge plus that the connection is collapsible and serviced, but it is unlikely that it will be significant in favor of this method for body repair, so I also refused this method6. Rivets. and finally, and finally the way I chose as a worker for my case is rivets. Cheap (riveper 1,500 rivets themselves 1-2 rubles ahead of the drill on average 60-70 apiece per hundred holes). Of the minuses, only high labor/time, and I have more than enough time, in Siberia 10 months a year winter and the rest of the time it is raining

By the method of fixing on the parts of rivets, there are the following types1. Under the hammer is the old version, so the planes and ships are riveted, including cosmic ones, we drill a hole to install such a rivet, we bother the rivet there, pour the rivet into some kind of hard object and rull it inside the back of the reverse from the reverse side2. Threaded. drill a hole, stick a rivet there, twist a special bolt into a rivet and twist until the rivet rivets inside the part, 3. Extensive. the easiest option, drill a hole, stick a rivet there, and rumble it with a riveter.

It is clear that riveting UAZ with hammer rivets is really unjustified labor costs, we discard the threaded ones because this is essentially a bolt connection, only instead of a nut is a rivet, there are exhaust.

Pros of exhaust rivets: 1. “Aircraft” technology, proven and reliable, the rivets themselves do not very much protrude from detail2. The strength is commensurate with welding (about strength below) 3. The riveted part is not deformed. Cheap very5. You can connect several layers of parts6. you can connect enough thick parts

Cons of exhaust rivets: 1. Very high labor costs2. Very high time costs3. A lered connection, that is, between the details, it is necessary to provide a stainless gasket, the rivets themselves must be smeared with sealant or mastic to become hermetic4. It is difficult to rivet complex shapes, rivets are best used to fasten parts overlap, and this is not always convenient, especially in modern machines, only a semiautomatic device is suitable for attaching parts of Vostye, you can still praise for UAZ, but for modern machines you can only rivet that not that not that not You can see the eye.

Exhaust rivets and their choice1. shittylin. made of the words of the sellers of Leroy Merlen, castoramas, baocentra are sold in the same place, such rivets consist of as a rule made of an incomprehensible mixture of incomprehensible metals, have unpredictable characteristics, predictably high price, are only good for attaching the toilet to the ceiling, which naturally falls on your head When you want to shit. Form a galvanic pair with ferrum, steel, iron if you want. Pour out along with the hole, provided that the periodic interaction with water in 2-3 years.2. Standard allumine (with steel or alluminated core). such rivets are made of allumin alloy, have predictable characteristics, are sold in stores of professional building materials, or instrumental stores. As well as the first option are bad for fastening iron t.to. Galvanized with him. They can be attached to non.incompatible compounds, which if they fall off, then it is not a pity to swagger. Withstand the lowest load. Riveted the most ordinary3. Steel. rivets are made of ordinary steel, steel core, withstand heavy loads, a little more expensive than luminous, require an enhanced riveter that costs a couple of Casires.four. Stainless steel-rivets do not rust, they do not form galvanic steam, withstand the loads comparable to welding, require a good rivet, and stand like a spaceship :-))) a joke, about 4-5 apiece, but they cost it

Now about the strength of exhaust rivets in numbers, that is, kilograms

Threaded rudder for 100 with your own hands. simple, conveniently, functionally

There was a need to put a threaded rivet in a hole on my car.Seeing the unimaginable figures of the cost of finished threaded strings ≈ 2000 rubles, the only decision was made to collect the device on its own.

There are options for remaking ordinary manual rivets in threaded ones, but I didn’t really like this option.Summarizing the experience of previously built such devices, and complementing the design by some RAC.offers from myself, I lay out the result.The device is not suitable for everyday and professional use, but for one.time use. the most!The principle of action. pulling the riveting with an internal screw when twisting the outer bolt relatively stubborn nut.Well, if we are all on the car site, I tried to use the automobile components as much as possible.

working screw (5 rubles). interchangeable screws, according to the diameter of the threaded rivet. Acquired by carvings M5, M6 and M8, strength class 8.eight. In the final form, the length of the working screw = 70mm.2-case (50 rubles) (something like that. This is the main part of the riveter. Many take ordinary bolts and drill through it a hole Ø8. There is a simpler solution. the fuel bolt KAMAZ 870022 m14. Almost everything has already been done in it, you just need to finish the hole in the bolt head3. a stubborn nut (20 rubles). I did not use the “raw” nuts from shops like Leroy, I picked up a normal potato wheel nut PE AUTOMOTIVE 01710900A M14 from trucks.4. support bearing. It is necessary in order to exclude tightening with a “screw” of a threaded rod. The penny bearing from AliExpress (is looking for the Thrust Bearing) came up perfectly. The outer diameter perfectly approached the nut, the internal. for the thread of the M14 of the fuel bolt. Initially, he used the supporting bearings apron of the racks, but with them the design turned out to be much more overall.5. adapter (25 rubles). Here, no matter how hard he tried, I did not look for the automobile component, but I never came up with a more elegant solution than to use the adapter internal-exacerburation thread, 1/2 “x3/8”. The external diameter also coincided with the diameter of the bearing. To save the total length of the tool (about 10mm), I cut part with external carvings.6. washer, put in accordance with the size of the working screw thread. It is necessary for centering from the bottom of the working screw in the body of the case so that the rivet is stretched without distortion.

Manual rivets. what kind of tool, how to work for them.

Manual riveper. a tool designed to fasten sheet materials. Most often with rivets, sheets of metal up to 3 mm thick are fastened with rivets, however, you can attach a sheet of metal to a profile or corner. We have a bastard exhaust, the principle of its action is slightly different than riveting with ordinary rivets and a hammer. In this article, we will consider the main types of manual riveting tools, how to choose rivets and how to use this device.

First of all, it is necessary to drill a hole through both fastened sheets, through and through. The diameter of the hole should be in the diameter of the rivets. Then we “charge” the rivet and insert it through both sheets and begin to squeeze the handle (you need more than one clamp). The rivet begins to flatten when the ball is completely drawn into a rivet. the tail of the rivet is bitten off. As a result, we have 2 sheets of metal stained on both sides. In the photo below, you can see the instructions in the pictures.

They shot a video with a partner for you how to use a riveter. I hope it will help you understand how and what to do.

Take, for example, the cheapest option from Stayer is the very first photo. He supports him all the diameters of the rivets (2.4 mm, 3.2, 4 and 4.8 mm), so you can choose the diameter of the rivets most suitable for fastened materials.

For example, thin rivets with a diameter of 2.4 mm are designed to fasten sheet material with a total thickness of up to 5 mm. Of course, there is still such a parameter of exhaust rivets as length. The longer the rivet, the more thick material can be fastened.

I bring to your attention a table of the ratio of the size of the rivets and the thickness of the material.

It differs from the usual one in that the “head” of the rivet can rotate 360 ​​degrees. This helps a lot when working in hard.to.reach places, where you can’t crawl out ordinary. True and it costs more expensive, about 350. We also consider the model of the company Styer.

For people who work on the riveter constantly, they release power options.

Differ from ordinary ones in that they squeeze it with both hands, respectively, forces are significantly saved. Imagine that you need to stuck 500 rivets. It will be difficult to perform such a volume of work with ordinary rivets, and you can stab all more quickly and without tension. What does the reinforced look like in the photo below.

Professional models with an increased service life

In addition to household models, for homework, there are also professional. Differ from households with a better performance and an increased service life. For example, the model of Kraftool. An ordinary, non.rotational model, but costs noticeably more. In the photo below the bracket craftol.

All rivets have 4 interchangeable nozzles-stucros for different rivets diameters. They change using a special key, which also includes.

Rivets are usually sold in small packages, 50 pieces. Rivets differ in diameter and length, the thicker and longer a rivet. the more expensive the packaging costs. For example:

When buying consumables, do not forget that rivets are needed for a rivet, exhaust. Otherwise the stores are sold in stores, which are riveted with a hammer.

Rivets with a secret head

Similar elements have other names. shock, clogging. Riveting with this part is carried out in several cases:

Rivets can be overlapping, in the way, as well as chain and chess method.

about rivets for a hammer, watch in the video below.

Summary

The threaded rivet, of course, is the right tool if there is a need for constant work with the blanks that should be connected without the use of the welding machine. If necessary, disposable work should not be spent on the purchase of a factory tool, it is easy to build it from improvised materials.

A special pistol for connecting parts can be useful for connecting parts, but not everyone knows how to use the riveper correctly, and what are the safety recommendations.