How To Tuck The Line Into The Trimmer

We wind the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

• The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
• One end of the line is inserted into the fixing technological hole located inside the spool.
• The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
• A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
• The left end of the line is passed through the hole in the outer part of the reel.
• The bobbin halves are assembled and put on the trimmer bar.

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

• Small electric trimmers with a working position of the motor and coil at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
• Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
• Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled in different ways. In the bobbins, a lamb is unscrewed from the lamb, in the coils, the latches are pressed from the latch and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

How to insert line into the trimmer spool? Instructions

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple teaching does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

• One groove. both tendrils are wound together in one groove;
• Two grooves. each tendril is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above-described option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

Automatic line winding to a spool

There is a type of reel in which the automatic mechanism winds itself. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. It is impossible to make the winding wrong in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

• One groove. both tendrils are wound together in one groove;
• Two grooves. each tendril is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above-described option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

• Small electric trimmers with a working position of the motor and coil at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
• Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
• Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled in different ways. In the bobbins, a lamb is unscrewed from the lamb, in the coils, the latches are pressed from the latch and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

• The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
• One end of the line is inserted into the fixing technological hole located inside the spool.
• The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
• A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
• The left end of the line is passed through the hole in the outer part of the reel.
• The bobbin halves are assembled and put on the trimmer bar.

We wind the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

How to insert line into the trimmer spool? Instructions

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple teaching does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

Automatic line winding to a spool

There is a type of reel in which the automatic mechanism winds itself. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. It is impossible to make the winding wrong in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

How do I fit the line into the trimmer? Operating tips

The trimmer is an excellent modern device designed for mowing unnecessary grass, and its main advantage is that this technique can be used in places where an ordinary lawn mower will simply not be able to reach due to its massiveness. It is necessary to understand in more detail what trimmers are, and how to choose the best option for a particular suburban area.

How to tuck the line into the trimmer?

Any machine for mowing vegetation is necessarily equipped with a spool, which, in turn, may differ in different models by the filament feed system (automatic, semi-automatic and manual). It is from this parameter that it is worth starting from before deciding how to fill the line into the trimmer.

In order to tuck the line into the trimmer, you need to take at least 5 meters of material, which is then folded in half. The center of the cutting element should be inserted into a specially designated place, and then the cutting attachment should be wound on the spool showing the direction using visual cues. At the end of all the work, the lid, of course, will need to be tightened.

What is a trimmer?

This equipment is based on the following elements:

• Motor, the main function of which is to rotate the cutting head at the end of the rod;
• Directly the head, consisting of a coil on which either a fishing line or a knife can be wound;
• Knives or line rotating at high speed, which are the main cutting part of the device, how to load the line into the trimmer, it will go a little further.

An electric device is inferior in its power to a gasoline one, so it is ideal for working on a standard plot of land, which is adjacent to a house with source of electrical energy. The main positive aspects of this technique are the absence of noise during operation, light weight, ease of use and, of course, environmental friendliness.

As for gasoline trimmers, such equipment, of course, is more mobile, so it can be safely transported from place to place and get rid of annoying vegetation in any area. It is not necessary to use electricity here at all, which has a positive effect on the functionality of such an apparatus. the cutting attachments can be changed, working with weeds of various types.

One of the most common attachments is the fishing line, so you should dwell on this element in more detail.

Types of trimmer line

As a rule, line separation is based on different sample diameters, which can vary from 1.2 to 4 mm. The most commonly used material is a material with a thickness of 2 mm, but in no case should we forget that the choice should depend primarily on the trimmer model.

There is one main rule here: the more power the apparatus has, the thicker the line should be.

This element can also differ in the type of its section. So, it can be round (suitable for cutting plain grass) or square (for mowing soft green cover), sharp edges (tall grass) or be equipped with notches ideal for thin grass.

Do not forget that with the help of a fishing line it is allowed to mow only grass, and for other, coarser vegetation, it is imperative to use knives.

Next, you should consider in more detail the process of how to insert the line into the trimmer correctly. Indeed, it is with this procedure that many consumers often have difficulties.

Line adjustment

One of the main rules when replacing and adjusting equipment is any manipulations with the mechanism Should be carried out exclusively with the engine off and the device plug disconnected from the mains.

Perhaps these tips will tell you how to tuck the line into the trimmer as correctly as possible and, accordingly, give your site a neat and aesthetic appearance. All that is required is to correctly select the cutting material required by the type and, of course, to determine the category of the most used trimmer.

How do I fit the line into the trimmer? Operating tips

The trimmer is an excellent modern device designed for mowing unnecessary grass, and its main advantage is that this technique can be used in places where an ordinary lawn mower will simply not be able to reach due to its massiveness. It is necessary to understand in more detail what trimmers are, and how to choose the best option for a particular suburban area.

Types of trimmer line

As a rule, line separation is based on different sample diameters, which can vary from 1.2 to 4 mm. The most commonly used material is a material with a thickness of 2 mm, but in no case should we forget that the choice should depend primarily on the trimmer model.

There is one main rule here: the more power the apparatus has, the thicker the line should be.

This element can also differ in the type of its section. So, it can be round (suitable for cutting plain grass) or square (for mowing soft green cover), sharp edges (tall grass) or be equipped with notches ideal for thin grass.

Do not forget that with the help of a fishing line it is allowed to mow only grass, and for other, coarser vegetation, it is imperative to use knives.

Next, you should consider in more detail the process of how to insert the line into the trimmer correctly. Indeed, it is with this procedure that many consumers often have difficulties.

What is a trimmer?

This equipment is based on the following elements:

• Motor, the main function of which is to rotate the cutting head at the end of the rod;
• Directly the head, consisting of a coil on which either a fishing line or a knife can be wound;
• Knives or line rotating at high speed, which are the main cutting part of the device, how to load the line into the trimmer, it will go a little further.

An electric device is inferior in its power to a gasoline one, so it is ideal for working on a standard plot of land, which is adjacent to a house with source of electrical energy. The main positive aspects of this technique are the absence of noise during operation, light weight, ease of use and, of course, environmental friendliness.

As for gasoline trimmers, such equipment, of course, is more mobile, so it can be safely transported from place to place and get rid of annoying vegetation in any area. It is not necessary to use electricity here at all, which has a positive effect on the functionality of such an apparatus. the cutting attachments can be changed, working with weeds of various types.

One of the most common attachments is the fishing line, so you should dwell on this element in more detail.

How to tuck the line into the trimmer?

Any machine for mowing vegetation is necessarily equipped with a spool, which, in turn, may differ in different models by the filament feed system (automatic, semi-automatic and manual). It is from this parameter that it is worth starting from before deciding how to fill the line into the trimmer.

In order to tuck the line into the trimmer, you need to take at least 5 meters of material, which is then folded in half. The center of the cutting element should be inserted into a specially designated place, and then the cutting attachment should be wound on the spool showing the direction using visual cues. At the end of all the work, the lid, of course, will need to be tightened.

Line adjustment

One of the main rules when replacing and adjusting equipment is any manipulations with the mechanism Should be carried out exclusively with the engine off and the device plug disconnected from the mains.

Perhaps these tips will tell you how to tuck the line into the trimmer as correctly as possible and, accordingly, give your site a neat and aesthetic appearance. All that is required is to correctly select the cutting material required by the type and, of course, to determine the category of the most used trimmer.

Briefly about the line

Taking into account the models of the tool, the thickness of the line is 1.2-4 mm. There are such configurations:

• Round is the most durable;
• Curly. for soft grass;
• Twisted or notched. for thin grass;
• Professional, NOT suitable for all instrument models.

When changing the cutting thread, you need to choose the one that suits your trimmer type. Preference should be given to Specialized. Before tucking the line into the trimmer spool, it is best to soak it in water for half an hour. Then it will become more elastic and stronger.

How to fill the line in the trimmer so that working with it does not get tired

Many summer residents use a trimmer to combat weeds. a scythe with an electric or gasoline engine. It is convenient when working in hard-to-reach places for a lawn mower: in fences, flower beds, houses, in a garden on narrow aisles, and can cut small branches. The main element of this miracle technique is an ordinary line wound on a reel. The device is simple, but the cutting part wears out quickly and requires replacement. And the question of how to fill the line in the trimmer worries many owners of summer cottages.

How to quickly remove the coil from the tool

Before the thread is wound on a bobbin, it must be removed. over, the methods of removal depend on the characteristics of the instrument. On a trimmer with a motor in the very ground, the coil has two side buttons, when pressed, part of the body is separated along with the thread winding devices.

On tools with a bent barbell, the lamb on the fixture is moved counterclockwise; having disconnected it, they remove both the bobbins and the spring inside it. On a trimmer with a straight bar, fix it with a screwdriver, rotate it clockwise and remove it. Then the device is disassembled either with the help of latches or by moving its parts in different directions. Take out the spring from the coil.

Threading the line into the trimmer

The main question is how to properly wind the line on the trimmer reel, securely fix it there?

In the case of a device with one tendril, up to four meters of fishing line is unwound, one end is inserted into the hole inside it, fixing the fishing line, and moved in the direction indicated by the arrow. The end of the thread is fixed in a groove inside the bobbin so that it does not unwind when it is assembled. If the groove has comments, then this free end is fixed with a finger. Then the coil is assembled.

How to refuel the trimmer coil if it has two tendrils? In this case, they check how many grooves there are. one or two. In the first case, both tendrils are directed into a common groove, if there are two of them, then each of them. into its own. 2-4 meters of thread are passed through the hole in such a way that the free edges of the thread are of the same length, and twist the bobbin in the direction of the arrow-pointer. The ends of the thread are inserted into the grooves or held with your finger, the device is assembled and attached to the trimmers.

In a spool with two grooves, the same piece of thread is folded in the form of a loop, sent into the groove between them and the ends are wound at the same time. Then repeat the previous assembly. With semi-automatic winding, the bobbins operate as follows. The fishing line is passed through a hole inside, its ends are fixed in the holes on the body, collect it and press the button. The thread can be easily wound in the correct direction.

It is important to remember that the cutting surface must be protected from solid objects so that it does not wear out. Otherwise, it will be necessary to constantly stop and, having removed the bobbins, replace the used fishing line. Let your work be NOT tedious and enjoyable!

Single Barbed Trimmer Spool

Reel for single-barb lawn mowers

Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of the trimmer reel movement.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. Passing the left end through the working hole of the coil and assembling the head.

Trimmer head with two tendrils

Double flute head

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). In principle, there is no difference between bobbins with one and two grooves, but with careless threading into the paired groove, there will be operational problems. Due to the likelihood of interlacing the adjacent line of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction of rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, the free ends (15-30 cm) are threaded into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do NOT worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off excess.

Winding the line to the trimmer

Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to winding the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

• Trimmer head with one working Mustache;
• Bobbin with two tendril fishing lines;
• Auto winding reel.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Preparing to wind the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

Compact Electric Trimmers.

Straight bar trimmer

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily unscrewed by hand clockwise.

Trimmer head with automatic line threading

Types of trimmer heads

Some models on the market are fitted with a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic trimmer head include the ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

Winding the line to the trimmer

Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to winding the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

• Trimmer head with one working Mustache;
• Bobbin with two tendril fishing lines;
• Auto winding reel.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Single Barbed Trimmer Spool

Reel for single-barb lawn mowers

Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of the trimmer reel movement.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. Passing the left end through the working hole of the coil and assembling the head.

Preparing to wind the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

Compact Electric Trimmers.

Straight bar trimmer

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily unscrewed by hand clockwise.

Trimmer head with two tendrils

Double flute head

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). In principle, there is no difference between bobbins with one and two grooves, but with careless threading into the paired groove, there will be operational problems. Due to the likelihood of interlacing the adjacent line of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction of rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, the free ends (15-30 cm) are threaded into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do NOT worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off excess.

Trimmer head with automatic line threading

Types of trimmer heads

Some models on the market are fitted with a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic trimmer head include the ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

No cord feed, coil does NOT spin

An automatic or semi-automatic head should feed the line without stopping the machine. But if She does not come out, then the reasons may be as follows:

• The line in the reel is not wound correctly, because of which the latter does NOT spin;
• The cord is not wound evenly, and the thread can get stuck between the turns (the thread should be wound neatly, turn to turn, without distortion)
• Too short ends of the thread come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the line is NOT fed (it is recommended to always adjust the length of the cord by pulling it slightly before starting the unit)
• The line is stuck together (will be discussed later).

High cord consumption

Basically, the cord runs out quickly if you hit the ground frequently with the semi-automatic head or press it down hard. The spool is unlocked, and the line, lengthening, is cut with a knife. Another reason that the cord runs out quickly is improper operation of the machine with an automatic head: the user often cuts the engine speed when mowing. But as we remember, the automatic head is designed in such a way that it is with each decrease in revolutions that a new portion of the line is supplied, so it is quickly consumed.

Second way

Some reels have a second method of securing the cord: you can charge 2 pieces of yarn instead of one folded in half. The line is replaced according to the following algorithm.

• Before you change or load a new thread into the spool, determine how many meters it will take using the method described above.
• One end of the cord Fold into a hook.
• Find the hole at the bottom of the bobbin for fixing the line, and insert the end of the thread bent in a loop into it.
• It is required to wind the cord according to the direction of the arrow to the required level, and not exceeding the coil diameter.
• Do the same for the second bobbin compartment.
• The assembly of the head does not differ in any way from the method that was given when it was considered threading the bobbin with a piece of line folded in half.

For Shtil lawn mowers, there is a very simple and quick way to change the line without disassembling the mowing head, which you can get acquainted with by looking at this.

The ends of the cord protruding from the holes in the casing can be cut to the desired length when the part is installed in the trimmer. This can be done in two ways:

• Turned on the trimmer (when rotating, the ends of the line will be cut into a knife, fixed for THESE purposes on the protective casing)
• Cutting off the excess ends with scissors so that they DO NOT touch the casing body.

The second method is used if a large diameter cord had to be supplied, and the edging knife cannot shorten it.

If a charge was made to whine into the mowing head, but the length of the protruding ends of the cord is insufficient, then they must be lengthened before starting the machine. this applies to the head with manual adjustment. However, there are cases when using a semi-automatic mowing head, when, due to the insufficient length of the protruding ends of the cord, they do NOT automatically lengthen. In this case, it is necessary to turn off the unit (on electrical apparatus, it is imperative to unplug the plug from the socket), manually press the button located at the bottom of the part, and pull out a little line. After this procedure, the cord can again be extended due to centrifugal force, if you set the maximum spindle speed.

Line problems

Users of trimmers, both gasoline and electric, sometimes have problems with the cord. “Advanced” Owners of mowers easily cope with difficulties in automotive products, understanding why this happens, and for beginners, these are problems that have no rational explanation. But in fact, everything is solved quite simply. The most common problems that happen with the line are as follows.

Changing the line to a disc or knife

When ennobling a personal plot, park areas and other places where it is required to mow various kinds of plants, it is often necessary to change the cutting tool to trimmers. This is dictated by the fact that the standard pipe installed in the mowing head can only handle grasses. But when a bush or young growth of trees appears on the path of the worker, the fishing line cannot cope with such a task, and it needs to be changed to a more efficient cutting tool.

Trimmer manufacturers have foreseen such situations, and supplemented their products with a mass of attachments in the form of knives with several “petals” or in the form of discs, similar to circular saws.

If you replace the fishing line with a knife with several “petals”, then with such a tool you can mow both Tall grass and plants with thick and dry stems. And by changing the fishing line to a disk, the lawn mowers user becomes able to cut shrubs or small trees.

Knives and discs are installed according to the following algorithm.

• The first step is to remove, lock the shaft, the mowing head (turns clockwise) or the boot nut, if the unit has NOT been used yet.
• Place the dust or cutting knife so that it fits over the small protrusion (bushing).

Install the attachment cover on top of the knife and screw the nut onto the shaft (counterclockwise).

Tighten the nut (counterclockwise) with a pipe wrench.

For a better understanding of the tool changing process, see this.

Option

In this embodiment, the head is screwed onto the gearbox shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, follow 2 easy steps.

• Insert a screwdriver into the hole and lock the shaft.
• Grasp the head body and start turning it clockwise. Torque in this direction follows because the thread cut on the shaft is left.

Line winding algorithm

Depending on which trimmer model is used, the type, thickness and length of the line are selected. The diameter of the cord can be from 1.2 to 4 mm. It is not difficult to guess that the thicker you fill the cord, the harder and thicker grass it is able to cut.

There are 3 ways to find out which line diameter you can use on your mower.

• View information on the thickness of the cord in the instructions for the device.
• Look at the bobbin itself. It can contain information about the possible diameters of the line.
• Insert the line into the outlet. If it easily passes into it, then a cord of this diameter can be used.

The line is wound on a reel in the mowing head. Therefore, you first need to open it (this was discussed above). There are 2 ways to wind the cord.

Option

To remove the trimmer head, you will need to completely disassemble it.

• To remove the cover that covers the inside of the head, you must press on the latches (latches) located on both sides.
• After removing the cover, you will see a spool that needs to be removed from the body. Some spools have a spring under the bobbin, which must be carefully pulled out to avoid losing it in the grass.
• When you remove the bobbin, you will see a slotted screw for a Phillips or flathead screwdriver in the center of the case. It is possible that there may be a hex bolt or a nozzle “star”.
• Using a screwdriver, selecting the required bit (bit), it is required to Unscrew the bolt (counterclockwise).
• After removing the fasteners, grasp the body of the part and, swing it in different directions, Remove it from the gearbox shaft.

Cord breaks

If the line breaks frequently, this may be due to the following reasons:

• Stones, small branches and other solid obstacles come across in the grass;
• Users are mowing the grass right next to the fence, and if it is mesh, it cuts off even faster “antennae”;
• Poor cord quality (it is recommended to purchase a quality one)
• The outlet holes in the mowing head are worn out, which causes the line to be erased on the sharp edges of the bushings and break off (a complete replacement of the part will be required).

How to wind the line correctly on the trimmer reel. Step by step guide

Winding Algorithm

Insert the resulting loop into the groove.

Lay the line in accordance with the indicated direction on the element body.

Insert the short end into the slot on the side of the spool.

Fasten the long end in the opposite groove.

Place the spool with coiled line into the spool body.

Pull the line out of the locking slots.

Put on the cover and fix.

Trim the ends of the line, leaving 10 to 15 centimeters.

The replacement of the line is completed and now it remains only to screw the bobbin onto the trimmer and you can work.

How to choose a fishing line. length, diameter, restrictions

As for the length, you should count on the estimated frequency of use of the trimmer. The more often, the more it costs to stock up the expense.

Information about the possible line diameter can be found on the body trimmer spools. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the peculiarities of the cultivated area. The larger the diameter, the easier it is to mow tough grass.

Preparation. remove and disassemble the spool

On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:

Lock the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod.

Unscrew the bobbin case. In our example. strictly clockwise.

Unscrew the cover in accordance with the direction indicated on the body.

Take out the winding spool.

The preparatory stage has been passed. You can go to winding the fishing line.

How to wind the line on the trimmer spool. ATTENTION! Typical line problems

It is not in vain that they say: “Forewarned is forearmed“. Knowing about possible problems and the causes of their occurrence, you can prevent them in time. We recommend to remember or leave a memo.

Problem	Cause	decision
line break	Stones, branches and solid objects in the grass	Avoid collision
	Poor cord quality	Replace with a quality analog
	Wear of outlet holes in the head	Complete replacement of part required
the line is unwound	Loose spring in the coil	Check spring and replace if damaged
the line is sticking	Poor line quality, due to which it can melt under the influence of temperature from a heating head	Reel in less line or replace with a better line

For a better understanding of the mechanism of the process of changing the line into a spool with a guide prepared by FUBAG specialists: