How To Tuck The Line Into The Trimmer

Filling the line into the trimmer The line feed system from the trimmer can be manual, semi-automatic and automatic. Here is an example of how to thread the line into the trimmer (Trimmer BOSCH Art 30).

We fill the line in the trimmer.

I want to devote today’s article to the sore subject of summer residents and gardeners of the entire post-Soviet space How to fill the line in the trimmer. Not many trimmer manufacturers answer this question in their instruction manuals. Therefore, it is difficult for ordinary gardeners to figure out how to do it correctly.

I want to start with a brief description of the technical characteristics of the trimmers.

So, trimmers are electric and gasoline. The cutting element for trimmers can be a line and a knife. The line is ordinary, four. Pentahedral and intertwined (in the form of a pigtail). Knives come in 2, 3 and 4 bladed knives. There are also plastic and metal knives.

The line feed system from the trimmer is manual, semi-automatic and automatic.

The development engineers who create new models of trimmers clearly calculate the diameter (thickness) of the line and the number of knife blades, according to the power of the trimmers. Otherwise, the motor is overloaded, resulting in damage. And these are additional and significant costs.

Trimmers on the market today:

With one nozzle only with a line.
With two line nozzles and three-four-blade knife.
With one nozzle only three-four-bladed knife.

Our Kulibins have long ago learned to improve any mechanisms. So, for example, some gardeners make successful, in their opinion, replacement of fishing line with a metal cable, or fishing line. But at the same time, they do not think about the safety of their own and their loved ones, because, like a cable with the power of a working trimmer, it can easily break out and not only injure the mower and others, but leave him crippled for life. Using a fishing line can and gives a better effect, I have never personally tried it than a trimmer line, but such work has a number of inconveniences: when it comes into contact with hard objects, it loosens or can simply be pulled out of the reel without limit.

So, what is called closer to the topic. Here is an example of how to thread the line into the trimmer (Trimmer BOSCH Art 30). Everything is very simple. We started.

After you have chosen the line for refueling, you need to cut off the required amount of line, because all the line in the skein will not be wound into the reel.

Cut off and start winding.

Remove the coil and the protective cover from the coil.

They took it off. We fasten one end of the line into the gap and carefully and evenly wind the line.

The amount of line should be such that the protective cover of the reel closes and the line on the reel unwinds a little by itself.

We put the other end of the line into the hole in the protective casing.

Next, we take the coil and the protective cover of the coil. We squirt the end of the line from the reel into the metal hole on the reel’s protective cover. We tighten the line a little.

We put it all on the trimmer. Turn the coil clockwise until it clicks.

They fixed it. Now we connect the trimmer to the network. We put the trimmer in the starting position for work. We turn on the trimmer. Excessive line length will be cut on the trimming blade.

Coil in trimmer

That’s all we start working on.

Thick line

It is stored at the top of the trimmer body.

Material you can see

A little advice. Try not to let the line come into contact with hard objects when cutting. With this contact, the line will be cut. And since in this trimmer the line is not fed automatically, then every time you have to stop work, remove the reel and release the line again.

In addition to the standard lawn line, my trimmer has a thick line for cutting rough weeds. It has the shape of a pigtail, i.E. Three lines are tightly intertwined. This line has its own spool. Spare coil storage space

It is very simple to install such a fishing line into the reel according to the internal scheme inside the reel. We insert the center of the line with a metal mount in the upper part of the reel, and draw the ends of the line along the grooves and bring it out.

Heavy-duty line in a reel

This reel is attached to the trimmer in the same way as a reel with an ordinary line.

What is a trimmer?

This equipment is based on the following elements:

• Motor, the main function of which is rotation of the cutting head at the end of the rod;
• The head itself, consisting of a coil, on which either a fishing line or a knife can be wound;
• Knives or fishing line rotating at high speed, which are the main cutting part of the device, how to load the fishing line into the trimmer will go a little further.

An electric device is inferior in its power to a gasoline one, so it is ideal for working on a standard plot of land that is adjacent to a house with an electric power source. The main advantages of this technique are the absence of noise during operation, light weight, ease of use and, of course, environmental friendliness.

As for gasoline trimmers, such equipment, of course, is more mobile, so it can be safely transported from place to place and get rid of annoying vegetation in any area. It is not necessary to use electricity here at all, which positively affects the functionality of such an apparatus, the cutting attachments can be changed, working with weeds of various types.

One of the most common attachments is the fishing line, so you should dwell on this element in more detail.

Types of trimmer line

As a rule, line separation is based on different sample diameters, which can vary from 1.2 to 4 mm. The most commonly used material is a material with a thickness of 2 mm, but in no case should we forget that the choice should depend primarily on the trimmer model.

There is one main rule here: the more power the apparatus has, the thicker the line should be.

This element can also differ in the type of its section. So, it can be round (suitable for cutting plain grass) or square (for mowing soft green cover), sharp edges (tall grass), or be equipped with notches ideal for thin grass in diameter.

Do not forget that with the help of a fishing line it is allowed to mow only grass, and for other, coarser vegetation, it is imperative to use knives.

Next, you should take a closer look at the process of how to insert the line into the trimmer correctly. Indeed, it is with this procedure that many consumers often have difficulties.

How do I fit the line into the trimmer? Operating tips

The trimmer is an excellent modern device designed for mowing unnecessary grass, and its main advantage is that this technique can be used in places where an ordinary lawn mower will simply not be able to reach due to its massiveness. It is necessary to understand in more detail what trimmers are, and how to choose the best option for a particular suburban area.

How do I fit the line into the trimmer?

Any machine for mowing vegetation is necessarily equipped with a spool, which, in turn, may differ in different models by the filament feeding system (automatic, semi-automatic and manual). It is from this parameter that it is worth starting from before deciding how to thread the line into the trimmer.

In order to tuck the line into the trimmer, you need to take at least 5 meters of material, which is then folded in half. The center of the cutting element must be inserted into a specially designated place, and then the cutting attachment must be wound using the visual cues on the spool indicating the direction. At the end of all the work, the lid, of course, will need to be tightened.

Line adjustment

One of the main rules when replacing and adjusting equipment, any manipulations with the mechanism should be carried out exclusively with the engine off and the device plug disconnected from the mains.

Perhaps these tips will tell you how to tuck the line into the trimmer as correctly as possible and, accordingly, give your site a neat and aesthetic appearance. All that is required is to correctly select the cutting material required by the type and, of course, to determine the category of the trimmer used itself.

How to tuck the line into the trimmer so that working with it does not get tired

Many summer residents use a scythe trimmer with an electric or gasoline engine to combat weeds. It is convenient when working in hard-to-reach places for a lawn mower: near fences, flower beds, houses, in a garden on narrow aisles, and can cut small branches. The main element of this miracle technique is an ordinary fishing line wound on a reel. The device is simple, but the cutting part wears out quickly and requires replacement. And the question of how to fill the line in the trimmer worries many owners of summer cottages.

Briefly about the line

Taking into account the models of the tool, the thickness of the line is 1.2-4 mm. There are such configurations:

• Round is the most durable;
• Curly for soft grass;
• Twisted or serrated for fine grass;
• Professional, not suitable for all instrument models.

When changing the cutting thread, you need to choose the one that suits your trimmer type. Preference should be given to specialized. Before tucking the line into the trimmer spool, it is better to soak it in water for half an hour. Then it will become more elastic and stronger.

How to quickly remove the coil from the tool

Before the thread is wound on a bobbin, it must be removed. Over, the methods of removal depend on the characteristics of the instrument. On trimmers with a motor near the ground, the reel has two side buttons, when pressed, part of the body is separated along with a device for winding the thread.

On tools with a bent rod, the lamb on the device is moved counterclockwise; having disconnected it, remove both the bobbin and the spring inside it. On trimmers with a straight bar, fix it with a screwdriver, rotate it clockwise and remove. Then the device is disassembled either by means of latches, or by moving its parts in different directions. The spring is removed from the coil.

Threading the line into the trimmer

The main question is how to properly wind the line on the trimmer reel, securely fixing it there?

In the case of a device with one antenna, up to four meters of fishing line is unwound, inserted into the hole inside it, which fixes the fishing line, one end of it and move in the direction indicated by the arrow. The end of the thread is fixed in a groove inside the bobbin so that it does not unwind during assembly. If there is no groove, then this free end is fixed with a finger. Then the coil is assembled.

How to thread a trimmer coil if it has two antennae? In this case, check how many grooves it has one or two. In the first case, both antennae are directed into a common groove, if there are two of them, then each of them into its own. 2-4 meters of thread is passed through the hole so that the free ends of the thread are of the same length, and twist the bobbin in the direction of the arrow-pointer. The ends of the thread are inserted into the grooves or held with a finger, the device is assembled and attached to the trimmer.

In a spool with two grooves, the same piece of thread is folded in the form of a loop, sent into the groove between them and the ends are wound at the same time. Then repeat the previous assembly. With semi-automatic winding, the bobbins operate as follows. The fishing line is passed through the hole inside, its ends are fixed in the holes on the body, collect it and press the button. This allows the thread to be easily wound in the correct direction.

It is important to remember that the cutting surface must be protected from hard objects so that it does not wear out. Otherwise, it will be necessary to constantly stop and, having removed the reel, replace the used line. Let your work be fun and relaxed!

How do I fit the line into the trimmer?

In order for the area near the house to always look well-groomed and neat, it must be cut regularly. Fortunately, modern technology allows you to solve this problem without excessive physical effort. Electric trimmers are so easy to operate and maintain that even a teenager can use them to mow. The main thing is to figure out in advance how to fill the line with the trimmer.

How do I load the line into the trimmer?

So, we are faced with the task of correctly loading the line into the trimmer. Let’s take a closer look at where to start its implementation and what pitfalls can await us in the process.

Step 1 choose the line

Step 2 remove the coil from the trimmer

To perform this operation, the trimmer must be disconnected from the mains and turned over with the working head up. The further course of action depends on the trimmer model and the design of the coil itself:

• For small trimmers with a lower engine position, press the keys located on the sides of the coil and remove its upper part from the head;
• On trimmers with a curved bar, we clamp the coil body with one hand, while simultaneously turning the winglet located on the body counterclockwise;
• For trimmers with a straight bar and a gearbox, insert a screwdriver into the hole located under the coil, and then turn the coil body counterclockwise.

Step 3 disassemble the coil

After the coil is removed from the head, it must be carefully disassembled. It is better to do this on an already mown area, since there may be a spring inside the coil, which will be quite difficult to find in tall grass. After disassembling, we will have three parts on our hands: the body (top cover), the protective casing and the coil itself.

Step 4 measure the required amount of line

Newbie mowers are usually interested in how many meters of line to wind on the trimmer reel? There are two ways to resolve this issue:

1. Unwind a skein of line on a flat, dry place and separate half from it.
2. Measure 3-4 meters of line from the skein.

In any case, after the end of winding, the turns of the line should be on the body of the reel, without sliding off it. You don’t need to try to wind as much as possible, as the line will unwind poorly and break more often.

Step 5 winding the line onto the reel

How to attach the line to the trimmer depends on the coil design. Consider the option when the reel body has one outlet for the line. In this case, we clamp the end of the line in the crevice of the coil, and then we wind the line, trying to lay the turns as tightly as possible. The direction of laying the turns should be opposite to the direction of rotation of the coil and is usually indicated on its inner part. After the end of winding on the spool, you must put on a protective cover and bring the end of the line into it

If the reel is designed to work with two tails, then the line must be folded in half and laid in the groove in the center of the reel. Further winding will be carried out along one or two slots, depending on the coil design. The direction of winding must also be opposite to the direction of rotation of the coil. At the end of the ponytail, the line will also need to be led out into the holes on the top of the reel.

Single-barbed trimmer spool

Brushcutter reel with one antenna

Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is done in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these gardening devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer spool. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the line in the operating manual.

Trimmer head with two antennae

Double flute head

After removing the spool from the reel body, we determine the number of strands for winding the line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.

Preparing to wind the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

• Compact electric trimmers.

Straight bar trimmer

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily twisted clockwise by hand.

Winding the line to the trimmer

Measured and neat dismantling of the spool from the spit coil makes it possible to go directly to winding the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

1. Trimmer head with one working mustache;
2. Bobbin with two line antennae;
3. Automatic winding reel.

Trimmer head with automatic line threading

Types of trimmer heads

Some models on the market have a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic trimmer head include ease of threading the line, and the disadvantages of frequent breakdowns of the mechanism due to the complexity of the design and high cost.

How to properly wind the line on the trimmer spool

Many, having worked out the factory line on a recently purchased trimmer, try to wind a new one, but cannot, because they do not know how to properly wind the line on the trimmer spool (bobbin). It seems that there is an instruction, but it still does not work. Let’s try to deal with this issue in this article.

So, in order to wind the line, you first need to remove the coil from the trimmer so it will be more convenient. The method of removal will depend on the type of trimmer.

Than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Removing the coil from the trimmer

On small, bottom motor electric trimmers (when operating near the ground), the reel usually has two buttons on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (on such trimmers it is not yet possible to put a knife), you need to grab the coil body with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to the fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver crawls even deeper, and the coil will lock. Now we turn the whole coil clockwise (since the thread is left-handed) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted with a lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection between two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. Having reeled up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that at the time of collecting the reel the line does not unwind. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. A reel with one groove must have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, fix the resulting ends in special grooves, and if they are not there we hold them with our fingers. We pass both ends into the existing holes on the outer casing of the coil. We collect the coil and attach it to the trimmer.

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the bend into the groove between the two grooves, and simultaneously wind both ends of the fishing line, each along its own groove. Further actions are similar to the previous option.

There are also reels in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, without winding, are threaded completely through the holes on the outer body of the reel, collect the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Rotate the button inside the fishing line itself. In this case, it will not work to turn it in the wrong direction, since it can only turn in one direction. If you get used to it, you can wind fishing line on such a reel, without even disassembling it, you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!