How to unscrew a very small screw without a screwdriver
Use a credit card. insert it into the groove and try to twist. Use only an unnecessary card, because it may well be damaged during unscrewing.
The screw is removed by a credit card
How To Make A Mini ScrewDriver Which Opens Small Screws/Life hack
You can also take the “eyelet” from a can (soda, beer). Insert the broken off “eyelet” into the groove on the head of the hardware, scroll.
Use a regular coin. insert it into the groove and still try to twist.
The flat-head screw is removed with a coin
If the screw is not tight enough, you can try to unscrew it with your fingernail. The method is not always effective due to obvious reasons.
Try to unscrew the screw with a knife, inserting the blade of the latter into the groove. In this case, there will be a risk that you will bend the knife.
The knife blade is inserted into the recess and scrolled counterclockwise
The last way is to use pliers. Suitable if the screw is not fully tightened. It is advisable to use pointed pliers for this, and not ordinary.
The flat head screw can be opened with pliers
Option number 4. Unscrew the small screw
Let’s make a reservation right away that small screws are especially difficult to unscrew without having the appropriate tools at hand. Typically, these screws are found in various electronic devices. Ideally, tools intended for repairing glasses should be used for unscrewing (there will be no difficulties with finding them, and they are not very expensive). If such equipment is not available, use one of the methods described below.
Table number 1. How to remove a small screw.
| Step 1 | Use a knife. place the sharp end of it in the slot and try to scroll. It is advisable to insert the tip at a slight angle to increase the contact area. |
| Step 2 | Use a nail file. Proceed by analogy with the previous method. |
| Step 3 | If you have small, pointed scissors at hand, you can use them. But we will immediately note that such scissors are not the best option for unscrewing screws. |
| Step 4 | Use tweezers. Insert its sharp end into the groove and try to turn. |
On a note! Another good option is to use a regular nail, the square point of which is ideal for a cross recess. For example, an 80mm nail is suitable for mobile phone screws.
Torn off screw
It is not uncommon for screws with a flat / hemispherical head (or rather, slots) to break off, and there may be several reasons for this:
- using an old, low-quality or unsuitable tool;
- improper screwing in (with a hammer, for example);
- insufficient effort when unscrewing / twisting and, as a result, the screwdriver jumps out of the slot;
- Screw “acidification” (corrosion);
- incorrect use of hardware (without drilling, when it is necessary, or for an unsuitable material).
How to unscrew a screw without a screwdriver
The use of screws for fastening any products is convenient and reliable. But it often happens that you urgently need to unscrew the screw, but there is no suitable screwdriver at hand. Of course, using a screwdriver is the easiest and safest method, but if necessary, you can do without it. How to unscrew a screw without a screwdriver? Today you will find out about it!
Method number 1. Twisting
Carefully inspect the screwdriver with which you unscrew the screw, and, if necessary, change to a more suitable one. It is important that the tip fits snugly into the groove and is not damaged. If replacing the screwdriver does not help, you can use other methods. If you need, for example, to unscrew a screw from a wooden product, then hit the head, and then tap the tool with each application of force. You can also use pliers if possible, as we mentioned above. Or you can use it to seal the rubber band.
How to unscrew a screw with torn edges
On a note! To make the screw start scrolling, use a few drops of lubricating or brake fluid, kerosene. You can also heat the screw so that it expands. this is how the material surrounding it deforms, and the product can be unscrewed.
If all else fails, drastic measures can be taken.
Method number 2. Sawing
You can try to unscrew any type of screw with a flat screwdriver. Using an angle grinder or a metal hacksaw, make a straight slot in the screw head. But remember that the slot must be at least ½ of the head height, otherwise you risk destroying it. This method can be used in combination with other.
How to remove small stripped screws | stripped laptop screws | stripped phone screw removal
Option number 1. Cross recess
For starters, note that some screws may have one groove on the head longer than the other. If so, then you should only work with a longer indentation to simplify the task. We also add that the edges of these grooves can be grinded, and therefore you should work carefully, otherwise you can ruin the product.
One of the easiest ways is to use a coin. The method often only works with small screws. The coin must be inserted into the groove and then turned counterclockwise.
You can try to unscrew a loosely tightened screw with your fingernail. The actions are the same as in the previous method.
You can try to unscrew the screw with your fingernail.
Take the knife, place it in the recess (long if they are of different lengths) and scroll. Be careful, because if the screw is tightly tightened, and the knife you are using is of poor quality, then it (the knife) can be bent without achieving the desired result.
Using a knife to remove a Phillips screw
Use an old CD. Place its edge in the groove and twist. The CD itself may be damaged as a result of such manipulations, and therefore make sure in advance that it is no longer needed. The method will definitely not help with a tightly tightened screw.
You can cut a long groove on the head with a hacksaw, but this method is effective only when the hardware is not completely twisted, that is, if the head protrudes slightly above the surface. Hold the saw at right angles to the head and cut slowly and carefully. Further, when the groove is ready, the screw can be unscrewed with a flat screwdriver or improvised means (for example, a credit card).
A long groove is cut into the screw head
Use a suitable sized flathead screwdriver without a Phillips head. Tellingly, this can only work with large / medium diameter screws. Be careful not to rip off the edges of the slot.!
You can try to unscrew the Phillips screw with a flat screwdriver
Another option is to use a toothbrush. Melt one end of it with a lighter, then immediately insert it into the groove on the screw head. After waiting a little for the molten plastic to solidify, turn the brush counterclockwise. Of course, it won’t help if the screw is tightened too much.
Removing a screw with a toothbrush
Method number 1. Twisting
Carefully inspect the screwdriver with which you unscrew the screw, and, if necessary, change to a more suitable one. It is important that the tip fits snugly into the groove and is not damaged. If replacing the screwdriver does not help, you can use other methods. If you need, for example, to unscrew a screw from a wooden product, then hit the head, and then tap on the tool with each application of force. You can also use pliers if possible, as we mentioned above. Or you can use it to seal the rubber band.
How to unscrew a screw with torn edges
On a note! To make the screw start scrolling, use a few drops of lubricating or brake fluid, kerosene. You can also heat the screw so that it expands. this is how the material surrounding it deforms, and the product can be unscrewed.
If all else fails, drastic measures can be taken.
Option number 3. Unscrew the Torx screw
These are screws with a six-pointed star recess on the head. Such screws, by the way, are protected. with a rod in the center of the star. In any case, proceed with caution, because the edges of such a slot can easily be damaged.
Slotted screw Torx
Try using a flathead screwdriver. Insert its sting into a pair of opposite beams, gently scroll counterclockwise. And if the screw is protected, then insert the screwdriver between the rod and any of the beams, and scroll in the opposite direction.
A small flat screwdriver is used
To unscrew a protected Torx screw, try using a screwdriver for an unprotected one, but in this case, the rod on the head will have to be removed (this can be done, for example, with a center punch and a hammer).
Removing the center rod on the head of the protected Torx screw
Another possible option is to drill a hole on the tip of a conventional screwdriver for the star rod.
Drill a hole in a screwdriver for a regular Torx screw
Finally, you can use the same toothbrush by melting one end of it with a lighter (proceed in the same way as described in one of the previous methods).
Using the same toothbrush
Method number 2. Sawing
You can try to unscrew any type of screw with a flat screwdriver. Using an angle grinder or a metal hacksaw, make a straight slot in the screw head. But remember that the slot must be at least ½ of the head height, otherwise you risk destroying it. This method can be used in combination with other.
If the head of the bolt breaks off
In this case, you need to be patient and choose the appropriate course of action.
- A hole is drilled 3 cm less than the diameter of the bolt and a tap with a left-hand thread is screwed into it until the broken part begins to unscrew.
- If part of the bolt protrudes, then a cut can be made on it using an angle grinder for a slotted screwdriver and start unscrewing.
- A hole is made at the base into which the extractor is screwed counterclockwise. Then the damaged element is removed with a key.
The process takes several minutes, but there are products with a countersunk head under a hexagon, the edges of which are easily torn off. Torx of the right size will help to cope with this problem.
Option number 4. Unscrew the small screw
Let’s make a reservation right away that small screws are especially difficult to unscrew without having the appropriate tools at hand. Typically, these screws are found in various electronic devices. Ideally, tools intended for repairing glasses should be used for unscrewing (there will be no difficulties with finding them, and they are not very expensive). If such equipment is not available, use one of the methods described below.
Removing small screws
Table number 1. How to remove a small screw.
| Step 1 | Use a knife. place the sharp end of it in the slot and try to scroll. It is advisable to insert the tip at a slight angle to increase the contact area. |
| Step 2 | Use a nail file. Proceed by analogy with the previous method. |
| Step 3 | If you have small, pointed scissors at hand, you can use them. But we will immediately note that such scissors are not the best option for unscrewing screws. |
| Step 4 | Use tweezers. Insert its sharp end into the groove and try to turn. |
On a note! Another good option is to use a regular nail, the square point of which is ideal for a cross recess. For example, an 80mm nail is suitable for mobile phone screws.
Unscrew rusted bolt or nut by tapping
Tapping the bolt removes rust and scale, so it becomes easier to unscrew it. The operation is carried out with a hammer, turning with a special tool in order to create a torque. With care, as you can damage the product and you will have to drill it out. After removing the fastener, it is cleaned of rust and treated with graphite grease. If available, put on an anther on the connection.
How to unscrew an asterisk screw
The use of screws for fastening any products is convenient and reliable. But it often happens that you urgently need to unscrew the screw, but there is no suitable screwdriver at hand. Of course, using a screwdriver is the easiest and safest method, but if necessary, you can do without it. How to unscrew a screw without a screwdriver? Today you will find out about it!
How to unscrew a screw without a screwdriver