How to unscrew the head of the electrimmer STIHL. The first way

Trimmer for STIHL FS 38 grass how to refuel a fishing line for a trimmer. Antirun.Ru

First, for winding the fishing line, it is necessary to remove the coil (bobbin, spool) from the trimmer for the grass. certain acts will depend on the difficulty of configuration and the type of product itself:

Small electronic trimmers for grass with a working location of the motor and coils at the bottom, usually have side buttons on both sides of the bobbin. With the simultaneous press on their highest part of the coil, together with the internal contents for winding the fishing line is disconnected, while the lower remains on the trimmer. The analysis of the bobbin is better to create in an even smooth place, so that the spring does not jump out and not be lost;
Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, usually have coils with a special lamb: in similar structures, you should hold the rogue in a motionless position with one hand and the other counterclockwise twist the fixing bobbin on the bar barack. How to refuel a fishing line for a trimmer trimmer for grass? How to refuel a fishing line for a trimmer to a trimmer coil for grass. It is clear how to charge a fishing line for a trimmer for a trimmer for grass. After disconnecting the nut, the whole bobin is removed.
Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such mutual placement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third options of coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. How to refuel a fishing line for a trimmer in how true a cheap fishing line for a trimmer. 2. On your site. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the back of.

Which fishing line for a trimmer to choose to refuel a lawn mower

The thickness of the polyethylene thread depends on the model of the technique and varies from 1.2 to 4 mm. She may be:

With a round section. this is the most durable material for mowing herbaceous plants;
with curly section. used to mow soft plants;
twisted. used for thin grass;
professional type, is not suitable for all models of technology.

Read how to replace a fishing line for a trimmer on a trimmer Carver video

To change the fishing line for a trimmer on a lawn mower, it is necessary to purchase a cutting thread that will be ideal for a particular type of mower.

Coil with one working osik

The most ordinary option and a light sequence of actions:

The dimensions of the bobbin and the length of the unique factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the squeezer.located squeling fixing technological hole.
The fishing line for the trimmer is wound on the drum in reviting the spilles on the trimmer product direction. usually, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
The small section of the fishing line is left free to withdraw it out. it is fixed in the special side on the inside of the bobbin created to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding.In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves.Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Preliminary preparation

At first, for winding the fishing line is required take off

Coil (bobbin, spool) from a trimmer for grass. certain acts will depend on the difficulty of configuration and the type of product itself:

Small electronic trimmers for grass with a working location of the motor and coils at the bottom, usually have side buttons on both sides of the bobbin. With the simultaneous press on their highest part of the coil, together with the internal contents for winding the fishing line is disconnected, while the lower remains on the trimmer. The analysis of the bobbin is better to create in an even smooth place, so that the spring does not jump out and not be lost;
Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, usually have coils with a special lamb: in similar structures, you should with one hand with one hand to hold the rogue in a motionless position, and the other counterclockwise twist the fixing bobbin on the staging barack. After disconnecting the nut, the whole bobin is removed.
Electronic and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and with unhurried rotation, such mutual placement is achieved when the screwdriver enters the holes and the bobin is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third options of coil, depending on the design, are versed in different methods. In the bobbins with a lamb, lamb is twisted, in the reels with the latches, the fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then they are quite turned with their hands in the back sides until they are completely developed.

Preliminary preparation

At first, for winding the fishing line is required take off

Coil (bobbin, spool) from a trimmer for grass. certain acts will depend on the difficulty of configuration and the type of product itself:

Small electronic trimmers for grass with a working location of the motor and coils at the bottom, usually have side buttons on both sides of the bobbin. With the simultaneous press on their highest part of the coil, together with the internal contents for winding the fishing line is disconnected, while the lower remains on the trimmer. The analysis of the bobbin is better to create in an even smooth place, so that the spring does not jump out and not be lost;
Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, usually have coils with a special lamb: in similar structures, you should with one hand with one hand to hold the rogue in a motionless position, and the other counterclockwise twist the fixing bobbin on the staging barack. After disconnecting the nut, the whole bobin is removed.
Electronic and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and with unhurried rotation, such mutual placement is achieved when the screwdriver enters the holes and the bobin is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves.Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

How to remove the head from a trimmer for STIHL grass

One of the common devices designed for haircuts of grass is a trimmer for grass. It is very easy to work and maintained. That is why it became popular among the population. Its significant advantage is small weight. Even a child can cope with such equipment.

What it is?

A trimmer for grass consists of a cutting element, a bar, an engine and a handle with a control mechanism. It is designed to cut grass in garden areas, as well as to create the perfect lawn. Due to its compactness, the device performs the necessary work in those places where the lawn mower cannot get. In addition to grass, a trimmer for grass is designed to mow branches of trees and shrubs, as well as creating flower beds. Such equipment is not always used for the lawn, since the length of the grass will have different heights.

Specifications

The main technical characteristics of the trimmer for grass are:

power;
Equipment weight;
type of power (from the network or using the battery);
engine location (above or below);
type of cutting element;
Type of bar.

All this needs to be taken into account, buy a particular device.

How to choose the right?

Before buying this equipment, you need to understand for what purposes it will be used. How to replace the head of a trimmer repair for STIHL grass up to 20% of the income of poor debtors from. For a large section with a flat lawn, it is better to purchase a light model with slight power. If you need to improve the summer cottage, then you need to choose the model more powerful.

Cutting tool

So that the haircut process takes place easily, it is necessary to choose the right cutting element.

Its role often acts as an ordinary trimmer fishing line for a trimmer or knife. When choosing one of the species, it is worth evaluating the type of vegetation. The most wear.long element in the design of a trimmer for grass with shrubs. Like a head and. In accordance with these data, a cord is selected, a knife of a certain form. Rotor lawnies how to remove the coil from a trimmer for the grass Makita UM3830. 26.06.2013. An important element is the head for a trimmer for grass. We will consider its varieties below.

Mowing head for a trimmer for grass

It is a special assembled coil, inside which the cord is located. Its dimensions can be diverse. On the inside of the spool should be wrap a cord 15 meters long. Its ends are pulled out to a certain distance to perform work. When meeting with a solid subject, it is destroyed. A mowing head for a trimmer for grass can have a different design. It all depends on the type of device. They differ not only by the design, but also. Watch how to replace the head on a motorcycle chamber repair for STIHL grass with STIH. There is also a universal head for a trimmer for a universal grass, which is suitable for different equipment. This became possible due to special adapters.

The head for a trimmer for grass is classified according to the method of feeding fishing line:

Manual. In this case, the name speaks for itself, that is, the supply of fishing line is mechanically. To make the cord even longer, it is necessary to stop the work of the trimmer for the grass and manually stretch the ends.
Semi.automatic. How to remove the head from a trimmer for grass and that the thread cut on the when on the coil. How to replace, remove how to replace the head of a trimmer for grass with a repair of a trimmer for STIHL grass. If you want to replace the cord, you need the head for a trimmer for grass touches the ground. In this case, a special button is pressed and the anchor mechanism is opened. Next, the cord lengthening due to centrifugal. The main feature is that the procedure occurs when the trimmer is included.
Automatic. To extend the cord, reduce engine speed. Further, with an increase in them, the fishing line for the trimmer is automatically supplied.

STIHL FS 55. Change of coil of motorcycles to a knife

How to install a 2-blade knife on the motorcycle tank STIHL FS 55. Video Instruction how to change the braids of benz.

Repair trimmer for STIHL grass with STIHL FS 38

During the operation of the stihl, the cutting head sometimes breaks, it happens that a cable is torn.Repair.

From all of the above, it follows that a hand.headed braid for a trimmer for grass is uncomfortable. That is why you should choose an automatic type. However, such a head for a trimmer for grass is not popular with users, since during work a large number of fishing line is consumed. Therefore, the optimal type is semi.automatic.

Classification according to the method of refueling

The head for a trimmer for grass can have several ways to refuel the fishing line:

Quickly charged. The new cord is wound without analysis of the coil, that is, you do not need to remove it from the device. The end of the new element is touched into the coil and then wound a certain number of times. Upon reaching a specific value, the cord is cut off. The head with a fishing line for a trimmer for grass of this type is produced by Shindaiwa and Speed-Freed.
Collapsible. Here the name itself speaks for itself. To replace the new cord, it is necessary to remove the coil from the equipment, then unwind the old fishing line for the trimmer and wind up the new.

Design features

It should be noted that the cutting head for a trimmer for grass contains special arrows. They allow you to perform rotational coil movements in different directions. If there is a need to wind the fishing line for the trimmer towards rotation of the shaft, it turns into a specific position. How to remove a coil from a trimmer for grass, disassemble the braid head. Before as. How to replace, remove the mowing head of an electric trimmer for Black grass how to disassemble a coil. A large number of wound cord threaten equipment breakdown. Two arrows are contained only on imported models. Now the heads are presented on the market with one arrow.

If the cord is not wound after the semi.automatic head, then its previous winding is incorrect. That is, after the head for a trimmer for the grass was installed, the user did not pull the ends of the fishing line from the grooves. Another unpleasant moment in the beard of grass may be sintering the coil turns. Why is it happening? This happens when there is a cord with a solid subject. At the same time, it brakes sharply and, with the subsequent movement, the fishing line for the trimmer begins to go inside the device. Thus, it gets on the rogue and sticks together. Because of this, the employee has to take a break and correct the situation. However, this can be avoided. Before installing the coil, it is necessary to treat the fishing line for the trimmer with a special silicone substance.

How to remove a mowing head from a trimmer for STIHL grass

Warranty production of the factory refueling of a trimmer for the grass will be in demand for fishing line substitutions. Having a very approximate idea of how to tuck a fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. How to wrap a fishing line for a trimmer to a trimmer coil for the grass, how to season a fishing line for a trimmer to a trimmer coil for grass. Autocut for a trimmer for STIHL FS 55 grass refueling the fishing line in a trimmer coil for grass 2 part winding of the fishing line on. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate this process.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The most ordinary option and a light sequence of actions:

The dimensions of the bobbin and the length of the unique factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the squeezer.located squeling fixing technological hole.
The fishing line for the trimmer is wound on the drum in reviting the spilles on the trimmer product direction. usually, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
The small section of the fishing line is left free to withdraw it out. it is fixed in the special side on the inside of the bobbin created to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves.Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

Automatic winding of the fishing line on the reel

There is a type of coils, in which the automatic mechanism performs winding without the help of others. it is quite only to correctly season the fishing line for the trimmer from the user. How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction. How to remove a coil from a trimmer for grass? How to wind a fishing line for a trimmer in in order to refuel a fishing line for a trimmer. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are tied through the hole on the outer case, the bobbin is assembled, and when rotating the winding button for the trimmer, the snitches are wound without the help of others. It is unrealistic to make the winding erroneous in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Warranty production of the factory refueling of a trimmer for grass will inevitably require replacement of fishing line. Having a very approximate idea of how to fill the fishing line for a trimmer to the coil of the trimmer for the grass on their own, beginners are reluctant to take this matter. However, with some skills, the development of this simple science does not represent any difficulties, and the presented instruction below will facilitate this process as much as possible.

Re Spooling the Stihl FSE 60, FSE 71 & FSE81 Electric Strimmer with C 5-2 Autocut mowing head. ⛳

How to wind a fishing line for a trimmer to a trimmer coil for grass

Trimmer for grass is an excellent solution for those who have a large garden or lawn near the house, which must be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, there will be a need to replace certain elements, and this will have to learn.

How to do it? To replace the main cutting element, first you must choose the right it. In principle, in the operating manual for motorcycles, the diameter of the thread should be used in it.

When you purchased the necessary cutting element, try installing it correctly. It should be noted that on the Internet there is a huge number of videos that will help you figure out how to correct the fishing line for the trimmer to the coil of the trimmer for the grass.

How to change a fishing line for a trimmer on a trimmer

Below we have brought step.by.step instructions for replacing a thread of a trimmer for grass.

The first thing to do is disconnect the tool from the network and turn off the engine. Then it is necessary to remove the head of the trimmer for the grass. This can be done using a simple screwdriver lowering it into the gearbox hole to exclude the turn of the shaft. And then just unscrew

Types of trimmer heads for coils

The main elements of the trigger is a mowing spike, which is a cylindrical case with a coil inserted inside (bobbin). A fishing line for a trimmer (cord) is refueling into it. The heads differ from each other in the method of supply and refueling of the cord. There are three types of heads in total:

Automatic. The fishing line is submitted after that, as the user reduces engine speed. Automatic supply of the cord is very convenient when you need to do a large amount of work. The minus of such a head is a large thread consumption.
Semi.automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its operation is arranged so that the fishing line for a trimmer begins to automatically lengthen at a time when a trimmer for grass works at full speed. It is only necessary to slightly hit the apparatus with the head on the ground (this will remove the locking of the fishing line), and the cord due to centrifugal force will move out of the bobbin. Then the fishing line for the trimmer is cut to the required length with a knife, which is located on a protective casing.
Manual. To lengthen the cord, it is necessary to stop the device. After that, the fishing line for the trimmer will need to be pulled manually.

How to clean a carburetor?

You should start by checking the absence of open sources of fire nearby. You can not repair in a closed room. This is fraught with gasoline leakage.

Unusual skateboards that go themselves
Washing machine electric motor connection diagrams
Sunny batteries of a country house

With a flat screwdriver you need to unscrew the screws to remove the plastic air filter casing from the motor. The extracted filter is checked, cleaned with a vacuum cleaner or replaced with a new one (if the condition is unsatisfactory).

You also need to remove the inner cover of the filter, which is located under the casing. This, unscrewing the bolts, is easier to make a cloth key. Air hose is attached to its inside, which will also have to be removed.

Finally, reached the carburetor of the device that can be dismantled. Disconnecting the fuel hose going to him from the tank, t.e. Having removed the clamp, the hose is turned, trying to remove from the pipe. You need to do work carefully. After all, in the presence of fuel in the tank, it will certainly spill.

The carburetor is attached to the engine with two bolts, for unscrewing which you will need a rolled head. Unscrewing the second bolt, try not to drop the carburetor so as not to damage the spring suspension.

The next step is removed the return spring. It is more convenient to carry out surgery from the side where it is attached to the motor. Now you can remove the cable responsible for the position of the damper, gently turning the carburetor counterclockwise.

Having removed the carburetor, unscrew the bolt fixing the fuel chamber cover.

14,000 Pressure Washing Mistake (Never Do This)

Cleaning is carried out with a special liquid or WD-40 and a copper wire from which isolation is removed.

Finally, you can remove a plastic float located under the chamber cover that regulates the level of gasoline, for which the hairpin is pre.removed.

The camera must be cleaned of plaque. The insides of the carburetor are abundantly wetted WD-40 (or analogue), wiped dry. By repeating the operations several times, they clean the copper residential fuel channels, purge them, since their pollution is the main reason why the motor stalls or does not start.

Having done all the described steps, they collect the carburetor in the reverse order.

Having installed it in place, connecting the hose, air is expelled from the fuel chamber. The repair is completed on this.

After the described manipulations, the technique will start easily, and work stably.

How to lubricate a trimmer gearbox for grass / Gearbox gearbox / Reducer Motokosa

Lubricate a trimmer gearbox for the grass at least once a year, but it is better to inspect the lubricant after every 20-25 hours of work or when the gear noise in the motorcade gearbox appears. How to lubricate the gearbox gearboxes. For lubrication, at first you need to clean the cork itself and the place around the traffic jam and the remnants of the grass, so that they do not fall inside the gearbox when filling it with grease. Then you need to turn out the cork for the lubrication of the gearbox (for example, the Echo lawn mower is a key for “17”, in Husqvarna-a 6-garnet on “5”, for Chinese lawn mower-the key on “12”). It is better to use the same manufacturer as your trimmer for grass or just from world-famous brands, such as Oleo-Mac, Stihl, Husqvarna, Oregon, Liquimoly, Litol-24, Azmol 158 and T.D., If only it was not a fake! The tube, if new, print, removing with your fingers a cork or piercing the cover with the back of the lid in the nose of the tube. Then we put a trimmer for the grass on the left side, and rotating the knife with one hand (so that the gears are smashed and the entire volume is filled), squeeze the lubricant from the tube with the 2nd hand through the hole inside the gearbox before its full filling. Then we twist and clamp the trimmer gearbox for the grass and a tube plug with a lubricant. If the lubricant is not in the tube (and, for example, in the jar), take a honey syringe without a needle, take out the piston, fill the lubricant (with your finger) in the syringe, and then fill the gearbox of the trimmer for the grass from the syringe from the syringe.

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections

Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

How to remove the coil and replace the fishing line for the trimmer

The owners of the trimmers, mainly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or fishing line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.by.step instructions given later.

Before refueling the fishing line for the trimmer to the coil, drown out the engine of motorcycles or de.energize the ethletric trimmer for the grass to avoid injuries that may occur in case of accidental rotation of the cutting tool.
Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, to twist the coil of the trimmer for the grass should be right, that is, clockwise.
Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
Cut the required amount of fishing line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the fishing line, since this will lead to increased load on the engine and greater consumption of gasoline.
Find the middle of the segment of the cord, folding it in half. You will get a loop.
Special grooves are cut out inside the coil (there may be holes). Insert the loop from the fishing line into this groove.
Wind a fishing line for a trimmer to a coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the fishing line about 20 cm long and fix them in the grooves located on the sides of the coil.
Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
Dress the lid and fix it with latches.
Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Tighten the coil of the trimmer for the grass will need to go to the left (against h. Arrows).

We offer to familiarize yourself with the tomato match characteristic and description of the variety

The first stage of operation Motokosa is running

Before you start using a motorcycle, worry about running engine. Such actions will significantly extend the duration of the gasoline engine

This is important, since at the stage of the running.in the mobile details to each other occurs to each other. In addition, running.in allows the owner to quickly acquire the skills of using the device

The basic rules that should be taken into account at the first stage of use of motorcycles:

Do not display the engine for long.term functioning at maximum speed. Use the speed of the maximum torque;
Carefully monitor the temperature of the engine;
Do not work with the device in case of overheating, and also do not use a motorcycle, not heating the device;
Be sure to replace the oil after running in;
Do not overload the engine;
regularly perform fuel filter cleaning, as well as cylinder ribs. To do this, you can use a brush, as well as compressed air;
Clean the air filter. It is advisable to carry out this procedure every 10 hours. If the filter is broken, then it needs to be replaced;
Carry out the lubricant of the tip of a flexible pipe every 20 hours;
if necessary, sharpen cutting knives.

All of the above rules for caring for a motorcycle will allow you to run the engine in a sparing mode, as well as maintain the functionality of the device and extend the life of the motorcycles.

How to remove a pressed reel from an electrimmer

LED lighting lighting device for Aquarium lighting inexpensive and harsh. Trimmer for Bosch Art 20 grass Three SL during operation. How to launch a gasoline cutter. gasoline trimmer for grass. Start steep gasoline cutters. trimmer for grass electric skil seven hundred 30 5 AA. trimmer for grass Bosch Art 20 6 SL Full. Trimmer for Forte EMK-360 herb, Changing Kosille fishing line. Charger for serving from a gas cylinder without the help of others. How to wind a fishing line for a trimmer to a coil Trimmer for grass. Trimmer for Bosch Art 20 6 6 Combitrim. Cheap trimmer for Bosch Art 20 grass three SL. How to wind a fishing line for a trimmer to a trimmer coil for grass? Trimmer for Bosch Art 20 grass Three Easytrim. Bosch Art 20 Three SL. How to assemble and launch a trimmer for grass (shield) Part 3.5. Piece for Tits from China.

This trimmer for the grass does not need to take a coil every time, very fundamentally change the fishing line for a trimmer in an existing coil for a new skein.

To change the ruler for a trimmer for Bosch Art 20 grass Three EasyTrim, I propose to use this annotation I provided below.

Trimmer for Bosch Art 20 grass Three EasyTrim, according to the instructions, is required to have a 1.6 mm wide line for a trimmer wide, but this device will perfectly convey a fishing line for a 2.7 mm wide trimmer wide. And from time to time I would like to note that the fishing line for a trimmer two mm will facilitate the mowing process.

Fix the resistance of the coil of sixteen so that it does not twist.

Return the coil cover fourteen counterclockwise and remove.

Remove the empty coil of seventeen from the lid.

Spend the end of the latest or tightened coil through the hole

Lower about nine cm of a mowing fishing line from a coil.

Install the spool with a lid fourteen on support

Now you need to take 5 meters of the latest braid fishing line and make it in half (to find the middle). In the middle part of the coil, of course, there is a notch (in some structures. hole), for which our fishing line is needed for a trimmer. The arrow showing the direction of winding is also on the coil. A fundamental detail. If the coil has two.

Many owners of garden shields are amazing configuration issues Kosille fishing line In the head of a trimmer for grass. At the same time, this is transformed in the whole deed, which is able to make not only the tool, and the mowing of an additional non.working. To prevent a similar situation, we will gradually analyze the process of configuration of the cord (mowing fishing line) in the nozzle.

Make a nozzle out of the box. To do this, it is necessary to cooperate the lateral hole or the puck of the upper shape and seizure on the axis, stick the screwdriver and fix the shaft from scrolling. Then there is an opportunity to unscrew the nozzle. Keep in mind that the thread on the shaft has a left cut, respectively, it is necessary to unscrew the element, turning it to the right.

The next step is the disassembly of the device body. Usually the lid is attached through the slit holes with the slopes. To open it, it is necessary to lower the valves into the body and crush the edges of the lid. If the nozzles have an automatic or automatic mode of supplying a mowing fishing line, this means that there is a spring when there is a spring when.

I wish to intend this article by a painful topic of summer residents and gardeners of the entire post.Soviet place “How to fill a line in trimmers”. Not all Russian trimmers’ industry is far away answers this question in its own operating instructions. Therefore, ordinary gardeners are also difficult to realize how to do it true.

About the manufacturer Stihl

The history of this German brand begins in 1926. At the initial stages of its development, the company was engaged in the production and implementation of various components for washing and steam machines. It all began, like many companies, with a small production and narrow orientation, which made it possible to focus on the quality of the manufactured products.

In the early 30s, the first Stihl chainsaw was released, which is characterized by convenience and functionality in those days. The company is developing at a long time, constantly introducing new tools, which gives it the opportunity to enter the international market. And already in 1931 the first regular supplies of products in STIHL were organized

To date, the company has launched its activities in more than 160 countries of the world, opening new centers and production departments in Switzerland, China and many other states. This is understandable, because the assortment of the company is impressive: motoburs, gasoline sprayers, mowers, gasoline trimmers for grass, chainsaws and much more. I would like to note that Shtil chainsaws are very popular due to their functionality and acceptable price.

How to choose a trimmer for the head of the head?

So that the head of the mower is highly efficient, the owner of the bushore should approach it correctly. In this case, several factors should be taken into account:

An experience. If the buyer. Novice gardener, it is best to buy an automatic coil. Semi.automatic and manual coils are best suited for more experienced gardeners;
Material. The reliability of the coil depends on this. They are considered the most durable metal models, but they weigh much more than standard plastic devices. When working with a metal coil, the braid engine is under a large load, so you only need to buy them to work with a powerful brush;
The diameter of the used mowing fishing line. For medium power trimmers, coils are used, which can be tightened with a wire thickness of not more than 1.6 mm. lawn mower with a capacity of more than 2.5 liters. FROM. Lamps can be installed that can be delayed using a cutting cord with a thickness of more than 2 mm.

An important role in choosing a coil is also played by the simplicity of its design. For beginners, coils consisting of a minimum of parts are best suited. experienced gardeners can use heads with a large number of elements in their design.

TOP 3 most reliable drums for home use

The market has a rating of the most durable mowing heads. They are distinguished by the simplicity of the device, reliability and resistance to damage. These include:

3rd place. Bosch K-103. This is a universal coil weighing about 300 g. Most often used to equip Makita and Hyundai motolers. The model is characterized by low energy consumption, impact resistance and durability. The core and its other parts are made of forged steel, and the case. From plastic;

2nd place. Flymo 15. This semi.automatic model of a trimmer for grass is equipped with a thin cup, which increases the flow rate. Nevertheless, he worked perfectly when he mowed grass in rocky terrain. To work with it, you need to use only a thin fishing line for a trimmer;

1st place. EFCO 8100. This model is one of the most reliable mowing heads. It works in fully automatic mode, which facilitates its filling with a cut cord. Only thin hair is used to work coil. The model of the model is made of durable multilayer plastic.

Despite stability and durability, all these coils are much cheaper than other analogues of lower quality, which makes them leaders in the post.Soviet market.

The relatively high price of STIHL products can be scared away by many, but if you think about what is more important. reliability and good result or savings that are in harm with the quality? But, if you set out to save money, we offer you an option for the lawn mower with your own hands, collecting the device with your own efforts you will know all the nuances and the structure of the tool.

Of course, you can choose cheaper Chinese counterparts, but then no one can vouch for the result of the final work and for the life of the service, which is very short.lived among such models. So it is more profitable to purchase a mow from an authoritative company once, which is certainly Stihl, and enjoy stable work for many years of operation.

Problems and Methods of Eliminating. DIY repair

But what to do if suddenly avoided breaking the mechanism failed? We will not understand the reasons for this, but it will not be superfluous to consider possible problems that may arise with a mowing, as well as methods for eliminating their own forces.

The engine does not start. If you are faced with this problem, then you first need to estimate the amount of fuel in the fuel tank, it may not be a problem as such, but you just need to add fuel and continue to work. By the way, the used fuel is worth separately, because the life of the lawn mower depends on its quality. Experts recommends AI-92 gasoline, not lower.

Stiga Robots Robots are an innovation in the agricultural industry, which managed to win the hearts of many farmers and summer residents.

Homemade disk sawmill. easily and simple, thanks to the detailed instructions that you will find on this site.

They wondered: “How to choose a professional saw without experience with this tool?”, Then you here // MachinSpec.COM/Lesozagotovitelnaya/Benzopila/Kak-Vybrat.HTML.

Another probable cause of unstable engine operation may be pollution of the fuel filter. Carefully examine it, clean it, if there is a need for this. If the filter is not amenable to independent repair, then it should be replaced with a new.

Do not forget about the air filter, the clog of which can also lead to the failure of the tool. In order to avoid this, the part is removed and washed in water with detergents, or in gasoline, if there is no access to water supply.

Lawn mower Stihl

Then the filter must be carefully rinsed and dried, carefully monitoring the integrity of the structure. Before installing the part in a mower, you need to lubricate it with a small amount of oil. However, if you do not want to mess with cleaning the unit, then we suggest you familiarize yourself with the lawn mower with the mulching function, because it will not only cut the lawn, but also prepare further fertilizer.

The spark plug can also affect engine performance. It is necessary to unscrew it and check the condition, if necessary, then replace it with a new.

If after all the manipulations done, the engine still does not start, then you can resort to the advice of experienced masters who used them in practice.

It is necessary to adjust the speed using a carburetor screw. The mower is put so that the fuel falls pointwise on the bottom of the carburetor. For this, the tool is put so that there is an air filter on top.

Next, you need to remove it and pour a little fuel in the carburetor, then installing all the details in place. The engine should start.

You can pull the label handle, while closing the air barrier air damper. Then open it and pull the starter a couple more times. This is a fairly universal way, proven for years.

These tips are not a panacea, but they are quite effective and useful.

The braid stalls immediately after starting. The main reason for such a problem is the incorrect adjustment of the carburetor. Determining this problem is quite simple. strong vibration will be felt when the mowing. You can fix the problem yourself, looking into the instructions, where the problem and methods of elimination are described in detail.

Particular attention should be paid to the fuel channel, often it is the reason that the tool stalls. Check it regularly and clean it from pollution.

Characteristics of the travic

Various small details, such as a cable or fuel intake hose, can affect the stable operation of the tool. Therefore, you need to monitor their condition, check for the presence of cracks and small punctures.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Sources:

https://1-tools.ru/svarka/STIHL-fs-38-kak-zamenit-lesku.html
https://1-tools.ru/rezka/kak-snyat-golovku-s-trimmera-shtil.html
https://drillzone.ru/dlya-strojki/kak-snyat-golovku-s-trimmera-shtil.html
https://programka.com.ua/instrukcija/oborudovanie/kak-snjat-golovku-s-trimmera-STIHL
https://101benzopila.ru/kak-snat-kosilnuu-golovku-s-trimmera-stil/
https://domdetaley.ru/kak-snat-kosilnuu-golovku-s-trimmera-stil/
https://domdetaley.ru/kak-snat-trimmernuu-golovku-s-elektrotrimmera/
https://drillzone.ru/abrazivy/katushka-dlya-trimmera-shtil-fs-38.html
https://1-tools.ru/dlya-izmereniya/katushka-dlya-trimmera-shtil-fs-38.html

Grass Trimmer electrimmer, first, head, stihl, unscrew