How to use a manual cultivator correctly. The earth is already digging

How to work with a cultivator correctly

The soil plowing algorithm for the novice user of the walk.Behind tract is as follows:

• Check the integrity of the unit, make sure that the technique is not broken;
• Screw all the fixing elements;
• Pour fuel and oil into the motor;
• If it is necessary to reduce the territory of coverage, dismantle the side knives;
• Turn on the engine;

• During the plowing process, do not operate at the same time the levers of the rear and forefront. Your actions will harm transmission;
• If it is hot outside, periodically turn off the walk.Behind tractor. Let the engine cool down;
• After the completion of plowing, remove the mills to the outside. Remove the remnants of grass and garbage from them;
• Cultivator Wipe with a dry rag from contaminants;
• If necessary, use the syringe and pour oil into the transmission.
• Plow the site depending on its shape. Elongated process the coil, and the square. Plow the zigzag;
• If there is no need to plow all the plot, work with fragments. As plants and crops are planted in the ground;
• Gardeners with experience advise forming beds along the length of the site. With a parallel location behind the garden, it is easier to care for;
• If your garden is a hilly surface, place the beds parallel to the mowing trimmer line;
• In the process of preparing the garden, leave a narrow strip of land unnecessary. Otherwise you will not be able to go between the rows and work On the next bed.

It is not difficult to master the plowing using a walk.Behind tractor. But even agrarians with experience experience difficulties in the operation of equipment, if they do not take into account a number of features.

The main error is the choice of the unit for specific tasks. With a small garden, with an area-5-6 acres, choose small and light devices. If the walk.Behind tractor is heavy. Use special mills.

For a large allotment with an area of ​​20-30 acres, a block is needed with a capacity of 10 horsepower. Such a technique weighs at least 100 kg. It is equipped with it, or acquired separately, a stationary hinged plow.

Mini-technology works on an unacceptable principle. The earth does not turn over, but loosen to the desired depth. This is necessary so that the fertile layer of the soil remains untouched, otherwise you will not collect a good harvest.

Consider step.By.Step whether the alteration of the walk.Behind tract is necessary before moving directly to plowing.

I am sure that due to the simplicity and evidence of the design, the cultivator is made by different manufacturers and the packaging will be different. In my case, she was such.

Ryobi cultivator reviewed

The cultivator itself 100% illustrates the principle of “all ingenious. Simple”. According to the design and principle of the “tornadik” work, a corkscrew is great.

All you need to do is connect a pair of complete bolts pen, middle part and bottom with a “corkscrew”.

The middle part allows you to adjust the height of the cultivator from 80cm to 1m. Here you just need to insert a bolt into the corresponding hole in the middle tube. In principle, if desired (if, for example, you need to dig in fact deep holes), you can increase the length by finding another tube of similar diameter. But for all ordinary purposes, the one that is.

An anti.Slip foam “sleeves” are put on the handle. In my case, they were worn unreal Tight and inconvenient. This is generally the only bad thing I can say about the cultivator. As a result, as you can see, they simply do not. Most likely, I just cut them along, smear the pen with glue and put this foam rubber on them.

The lower part consists of sort of pointed spiral metal tentacles, which remind me of some kind of grade.

There is nothing special to add to this, the design is extremely simple and adding something else would just mean to just saturate the review with water.

Star cultivator

The folk name perfectly reflects the essence of this simple garden tool. In stores and reference books, it is most often called rotary, since its action is based on a block of rotating stars from a durable hardened metal. The stars are installed on the axes, sharpened and slightly deployed to simultaneously easily penetrate the soil and slightly turn it out.

Often behind the alarm block, a mobile rectangular bracket is installed. When the gun moves forward, it becomes at right angles to the frame, and with a return movement, it develops, taking with it part of the earth. If such a frame is sharpened, it cuts weeds well. In general, the tool is great for combined loosening and weeding.

How to plow the soil with a cultivator correctly?

Approached the consideration of the most important question. How to properly plow the soil as a cultivator. All useful information that may be required during the operation, repair or maintenance specifically for your model is contained in the instructions. Below are the basic rules that should be followed in the cultivation process in order to get a decent quality of processing.

• It is best to start plowing after rain. If the earth is well moistened, it is easier to process.
• If pouring rains went for several days in a row, the soil is not wet, but wet, it is recommended to postpone the work on the ground while the soil dries a little. Excessively moistened soil will clog the cutting elements of the technique.
• In areas of rectangular shape, they work in a circle, and in square gardens move in a zigzag direction.
• When working on rocky soils, do not rush, treat the soil at low speed. Pebbles can fall under the mills, thereby blushing them. A more dangerous situation when the stone flies out from under the car and inflicts injury to the operator.
• You do not need to push the cultivator in the process. This is an additional load for both the tool and for the operator. Set him the right direction, but don’t push.
• You can also adjust the width of the plow in a fairly wide range. To reduce the capture, remove the external cutters, to increase. Install them.
• You should not go behind the cultivator, because so you tackle the surface layer of the soil. Expand the handle so that you can move parallel to the unit.

Often inexperienced users the question arises why the cultivator buries into the ground. This is a really unpleasant situation. To fix it, change the position of the wheels or milling. Also often beginners are faced with the fact that in the process the cultivator jumps. This means that he lacks weight to plow the soil at the desired depth. In this case, weighting weights should be installed.

Operating principle

Cultivators for manual cultivation of the Earth are divided into two groups: looser and rotational models. Representatives of the first variety resemble in shape a hand equipped with three or five metal “fingers”.

In fact, this is a strongly modernized chip, for the work with which it is necessary to attach a lot of physical efforts. Therefore, this option is more suitable for working in greenhouses. The working element of rotational models is made in the form of stars, with a large number of rays.

During work, the stars literally “bite” into the ground, loosening the soil and at the same time cutting and grinding weeds.

How to use a rotational cultivator with stars? Thanks to the simplicity of the design, handling this device is quite simple.

The unit is installed vertically in the ground, the standard position of the cultivator: the stars are located in the aisles, the connecting axis passes over the bed. The cultivator is set in motion through the efforts made.

Even taking into account the fact that a person is a driving force, the cultivation of the Earth is much faster than when performing similar actions with a shovel or a hoe.

This moment is very important for pensioners who often suffer from radiculitis, in fact, they are the main buyers of this variety of garden inventory.

How to use a cultivator correctly

The use of this agricultural tool is actually quite light and does not require any special skills or skills, especially if you have previously encountered any garden equipment. And when buying in a box, there is always a operating instructions that will help you start work. But still we will try to highlight this topic, in which we will also give some useful tips for operating these units.

How to use an electric cultivator Unlike gasoline, the inclusion of this tool is very easy, so they often like to use the beautiful half of humanity, since even extraneous assistance is not needed! It is enough to take the extension cord in the length and connect this soilfire to it, then press the power button, it moves when the milling cutters is moved simultaneously with the grounding of the soil. The only thing that limits work is the rain and solid soil, for which more productive motor cultivators or motoblocks create sufficient pressure with their mass on the surface are needed.

How to work with a manual cultivator There are many varieties of these tools, so each of them is made for a certain type of work and is used in different ways! There are both options made in a completely compact size that require to occupy a sitting position near the ground, as well as large structures with a wheel or without. It is no more difficult to use them than ordinary rakes, it is enough to push it only so that they cut the soil with plane cutters, others need to make an exposure to break the soil lumps and reduce the density of the earth.

Where to buy a hand cultivator The purchase of this type of device can be made on the market or a retail outlet that sells hand tools for the garden. They have a low price, but at the same time it is still a tool that requires physical effort, low efficiency and productivity! So it is desirable to choose from motorized options that are more convenient, and in use are simple as the household appliances included in the outlet!

What kind of oil to pour into the cultivator The use of lubrication is required only in gasoline engine, when it is not used in electrical ones at all. The type of motors that are installed on soils require special two.Stroke oil, since during refueling it is simply added to gasoline, usually this ratio of 1 gram of oil per 25 grams of gasoline (1:25). Some attempts to use conventional lubrication for 4-stroke engines, but this is a mistake, they have a different composition, which, when mixed with fuel, does not quite efficiently lubricate the combustion chamber inside the cylinder block. As for the manufacturer, it is all about taste, most modern brands adhere to international standards, although the use of different technologies and chemical additives can improve the composition, which positively affects the durability of the tool in which it is added.

Apple blocks VPN use accounts

Order a laminate Balterio inexpensively

Telefonica integrates Netflix content on its platforms

How to use a cultivator correctly

The use of this agricultural tool is actually quite light and does not require any special skills or skills, especially if you have previously encountered any garden equipment. And when buying in a box, there is always a operating instructions that will help you start work. But still we will try to highlight this topic, in which we will also give some useful tips for operating these units.

How to use an electric cultivator Unlike gasoline, the inclusion of this tool is very easy, so they often like to use the beautiful half of humanity, since even extraneous assistance is not needed! It is enough to take the extension cord in the length and connect this soilfire to it, then press the power button, it moves when the milling cutters is moved simultaneously with the grounding of the soil. The only thing that limits work is the rain and solid soil, for which more productive motor cultivators or motoblocks create sufficient pressure with their mass on the surface are needed.

How to work with a manual cultivator There are many varieties of these tools, so each of them is made for a certain type of work and is used in different ways! There are both options made in a completely compact size that require to occupy a sitting position near the ground, as well as large structures with a wheel or without. It is no more difficult to use them than ordinary rakes, it is enough to push it only so that they cut the soil with plane cutters, others need to make an exposure to break the soil lumps and reduce the density of the earth.

Where to buy a hand cultivator The purchase of this type of device can be made on the market or a retail outlet that sells hand tools for the garden. They have a low price, but at the same time it is still a tool that requires physical effort, low efficiency and productivity! So it is desirable to choose from motorized options that are more convenient, and in use are simple as the household appliances included in the outlet!

What kind of oil to pour into the cultivator The use of lubrication is required only in gasoline engine, when it is not used in electrical ones at all. The type of motors that are installed on soils require special two.Stroke oil, since during refueling it is simply added to gasoline, usually this ratio of 1 gram of oil per 25 grams of gasoline (1:25). Some attempts to use conventional lubrication for 4-stroke engines, but this is a mistake, they have a different composition, which, when mixed with fuel, does not quite efficiently lubricate the combustion chamber inside the cylinder block. As for the manufacturer, it is all about taste, most modern brands adhere to international standards, although the use of different technologies and chemical additives can improve the composition, which positively affects the durability of the tool in which it is added.

Roskasta: Work search applications are vulnerable to hackers and viruses

Google convinces Gmail users in the hope of protecting information

Dogs in food! An unusual Instagram profile blew up the entire Internet

Cultivator handling during work

While working with the cultivator, be sure to follow your limbs so that they are not close to the moving parts of the cultivator. Work Better in closed shoes: high boots, and even better. In boots. Schoolpanians or vietnamese reserve for other purposes, here they increase the risk of injuries. It is advisable to plow the earth with glasses and gloves.

After turning on cultivator there is no need to push, it is simply set in the right direction. Когда агрегат застопорится в земле, слегка покачайте его с одной стороны в другую, с вашей малой помощью он продолжит движение. In order not to trample the land just processed, turn the handle and go next to the plowed strip.

When working as a cultivator on wet land, large clods are obtained. The soil is then difficult to loosen, and the earth sticks to cutters. When the earth is very dry, the depth of processing is sharply reduced. In this case, they pass the strip first at a low depth, repeating its passage to the necessary. So work best with moderately wet soil. The low speed of the cultivator at high turns of the cutter allows you to more carefully process the soil.

Когда земля мягкая, для рыхления почвы лучше всего подойдет насадка в виде якоря. It is more convenient to move in rows or zigzags with a cultivator.

Some tips on how to handle the cultivator correctly

• If there are many small pebbles on the site, work at lower speeds.
• The motorcycle block will serve for a long time provided that the maintenance of the maintenance. Oil replacement, cleaning the unit, sharpening milling. The key to the “health” of your cultivator. Cannot be saved in oil. When pouring non.Suitable oil in the process, a solid sediment is formed, which clogs the unit nodes. As a result cultivator may fail. And then the costs of its repair will significantly exceed the savings that you managed to achieve on the change of oil. This also applies to gasoline.
• Important: you can fill in fuel only with a stopped and cooled engine. After refueling, check the tightness of the fuel tank.
• All settings should also be carried out with the engine turned off.
• If you feel the vibration during work, this is a signal about the problems that have begun. It is worth stopping the engine, finding the cause (most likely weakened the mounting of the parts) and eliminate it.
• A row in the garden is not always perfect. In order not to damage plants, you can reduce the cultivation strip, removing external mills.
• Powerful motor cultivators can move not only forward, but also backward. If necessary, change the direction of movement, withstand the pause until the milling stops.
• The cultivator must move smoothly and evenly. If it buries into the ground, then it is necessary to adjust the position of the wheels or change the mills in places.
• After using the unit, wipe all its metal parts with a rag. If necessary, rinse the mills followed by wiping dry. Security measures while working with a cultivator
• Do not trust children with a cultivator management.
• Do not allow people who are not familiar with the rules of handling him.
• Make sure that there are no other people or animals near a working unit.
• Follow the safe distance to rotating elements.
• Use special strong clothes, shoes and gloves. Laces, ribbons, floors of clothing. Nothing should hang out when moving.

Put the optimal amount of milling

Another common mistake is to put the whole set of mills at once. Over, with regret: “It will not be enough!”Now, if there were still a couple of sections on each side so that in one pass at once to dig a one and a half meters. In fact, the optimal amount of milling. The denser the processed soil, the already should be the width of the processing. And most likely, this will only have a positive effect on performance.

You can put all the mills and go out with them on a loam trampled to the ringing. The effect will not be at all the way you count. Cultivator will bounce on the mills, only slightly scratching the soil. That’s all.

In this case, remove the extra sections, and although the width of the processing will decrease, the thing will go faster. But this usually applies to processing for the first time, as the people say, “virgins”. And if the site is processed systematically and the resistance of cultivation is not so significant, then you can safely put all the mills, and even “give the gas”.

How to choose a manual type cultivator

When buying or independently manufacturing a hand cultivator, attach the main value to the choice. Useful tips:

• If loosening soft soils is required, then give preference to the rotational cultivator for giving. It’s good if the kit includes a knife-knife that cuts the grass and turns its roots from the soil.
• Since the solid land is “too tough” by the rotational device, select a manual cultivator-pusher for its processing.
• If your site is very close to the country, then you can put it in order with the help of a cornea. They can also loosen the soil.
• For soil in pots and containers, select a small manual model with short handles. A narrow mini-cultivator is also suitable for loosening the soil on alpine slides.

The use of a hand cultivator

Take into account some other choice criteria. About them:

• Check out the technical passport of the product;
• Pay attention to the strength of the metal parts, the reliability of their connection points;
• Take the unit in your hands to try to adjust the length of the handle and make sure that you simply and conveniently hold the device in your hands;
• Assess the mass of the structure so that it is not too heavy.

Hand cultivators for soil processing in the country. Rotary and mechanical

Obtaining a good harvest or proper type of personal lawn is preceded by a number of works on the processing of the upper soil layer. Numbering, harrowing, loosening, breaking up of the lands of the earth, removing weeds and their roots, dug up root crops. All this is a necessary, but physically hard work.

Requiring plus to everything significant time.

The advantages of their use are enormous. Mobility, the ability to process the lands that are inaccessible to heavy equipment, an increase in several times the speed of work. The quality of land cultivation increases many times, compared with the use of manual tools. Shovels or sales.

How to choose a manual type cultivator

When buying or independently manufacturing a hand cultivator, attach the main value to the choice. Useful tips:

• If loosening soft soils is required, then give preference to the rotational cultivator for giving. It’s good if the kit includes a knife-knife that cuts the grass and turns its roots from the soil.
• Since the solid land is “too tough” by the rotational device, select a manual cultivator-pusher for its processing.
• If your site is very close to the country, then you can put it in order with the help of a cornea. They can also loosen the soil.
• For soil in pots and containers, select a small manual model with short handles. A narrow mini-cultivator is also suitable for loosening the soil on alpine slides.

The use of a hand cultivator Take into account some other choice criteria. About them:

• Check out the technical passport of the product;
• Pay attention to the strength of the metal parts, the reliability of their connection points;
• Take the unit in your hands to try to adjust the length of the handle and make sure that you simply and conveniently hold the device in your hands;
• Assess the mass of the structure so that it is not too heavy.

The design of manual cultivators of the soil is most often quite simple. The task of this garden tool is the loosening of the soil for its aeration and facilitate the growth of roots, as well as the better water access when watering. The second function is the removal of ubiquitous weeds. And here the hand cultivator will give a hundred points ahead of the gasoline device.

In narrow aisles with bulky nozzles of a motorized unit, just not to squeeze. A compact manual device can be dealt with with the task, and hands will not experience the vibrations dangerous for the musculoskeletal system.

The simplest manual looser

This is a very simple and affordable tool. It consists of a rod mounted on a hilt of various lengths, from which three or more round in the cross section of the curved “claw” with small triangular nozzles at the ends, like a hook. Despite the primitive design, such a looser is quite effective. With it, you can easily and simply pick up the soil slices dried on the surface, and pulling the tool on the ground with a little pressure, they just achieve shallow grooves sufficient for regular episodic loosening.

Star cultivator

The folk name perfectly reflects the essence of this simple garden tool. In stores and reference books, it is most often called rotary, since its action is based on a block of rotating stars from a durable hardened metal. The stars are installed on the axes, sharpened and slightly deployed to simultaneously easily penetrate the soil and slightly turn it out.

Often behind the alarm block, a mobile rectangular bracket is installed. When the gun moves forward, it becomes at right angles to the frame, and with a return movement, it develops, taking with it part of the earth. If such a frame is sharpened, it cuts weeds well. In general, the tool is great for combined loosening and weeding.

Cultivator Grinda 8-421888

Classic rotary cultivator for six stars. To improve the loosening of the rays of the rotating mechanism, they are transverse. So they capture more soil, turning it out. Three holders have screws for fixing nozzles with stars, of which two on the holder. There is a plastic rubberized handle of a short format in the kit, but you can use a screw to attach a cultivator to a long holder using a screw.

Manual cultivator Wolf Garten Da-S

There are four stars in this cultivator, flat, longitudinal rays, converging. This facilitates the work and provides a gentle effect on the soil. Behind the stirlet block, a bracket is provided for removing weeds and distributing soil masses. The tool is made of stainless steel, which provides a long service life and lack of corrosion.

Plain cutter (Fokin looser)

The simplest device that can be bought in a garden store, so do it yourself. In its appearance, it is very reminiscent of a plug (staple) common in the southern regions of Russia, that is, a blade curved at right angles to the handle. A distinctive feature is a narrow blade, the width of which is comparable to the thickness of the cuttings and is 3. 5 cm, as well as a oblique cut of the blade.

Thanks to a specific form, it is very convenient to perform small work with a plane cutter, for example, to remove weeds in the basal zone of adult tomatoes, cabbage, pepper, and also to weed narrow rowers in a greenhouse.

Manual cultivator “Tornadika” (cornexer)

The production of these tools is branded and associated with summer residents with the name of the company. The device is very simple: on the vertical handle on one side, a horizontal handle of a perpendicular tube is mounted on one side, on the other there are several (usually three) teeth, spirally twisted counterclockwise.

Work as a cultivator, setting it on the soil and rotating the hilt. Thanks to this, two tasks are solved at once: the tagging soil is loosened, and if in the area of ​​movement of the teeth there is a weed, then it will be thrown to the surface, even if it has a very powerful root system.

The Tornadika cultivator is popular due to the fact that it is very easy to work: the back remains straight, and rather long handles allow you to rotate the device with a slight effort using the effect of the lever.

Types of cultivators

Classification of devices is carried out depending on the mechanisms used. Share cultivators with the following equipment.

• Electric. It is mainly used to process large areas. The performance of the device is possible only if there is an electricity source. The design has small weight and compact dimensions, in addition, such devices do not pollute the atmosphere by harmful substances.
• Battery. This type of equipment for working in small areas is used. The advantages of cultivators on the battery include high mobility and small dimensions.
• Gasoline. Another type of equipment that is considered one of the most common among summer residents. Has high performance, good mobility, convenient to use. But such devices must be properly served, not to mention atmospheric pollution by harmful substances.
• Mechanical. It is no secret that hand cultivators are very easy to use, they do not take much time and effort, and also differ in low cost. There are several types of designs of manual cultivators, starting with a simple tornado cultivator, which is ordinary forks with bent fingers on the bottom, and ending with a plane cutter.

The advantages of manual cultivators include that they are easy to make on their own. This does not need special skills, just follow the recommendations. For the manufacture of a particular design, you need the correct drawing of the product, a little free time, patience and, of course, some tools and materials.

Features of the use of manual cultivator

The main feature in the use of a manual cultivator for a summer residence is that working with them does not cause difficulties even among beginners, everything is extremely simple and clear. Before starting work, the length of the handle should be adjusted to its height so that the work does not cause discomfort.

Tools such as the Worner Divine must be placed strictly vertically to the surface, the links of the star cultivator. Placed between the rows of crops, and the connecting arc, if present, should be located above the soil.

When working with the cornea, plunging it into the ground, you need to turn it clockwise, then on itself. Another important feature is the inability to regulate the depth of penetration into the soil, it all depends on the applied force, if it is insufficient. There is no high.Quality processing, if exceeded, you can damage the roots of plants.

If you need to process a plot with soft land, loosen the beds, flower beds, remove small weeds, a rotary cultivator is ideal. On hardened and clogged earth, which contains clay rocks, the looser will be effective. For transplanting small bushes, point removal of weeds, the rooter should be used. The result depends on the correct choice of the tool.

With a huge assortment, manual cultivators are easy to do independently from improvised materials. The easiest way is to make it from an unnecessary bicycle, taking a wheel and frame from it. In addition, you will need a canvas of an old manual saw.

How and where to use

Handing a manual model is simple, although it is necessary to apply a large amount of effort. Since the rotary cultivator has a simple design, then in use it is simple. All that needs to be done is to install it in an upright position in the ground. The standard position is considered when the stars are located between the rows, and the connecting axes pass over the beds.

As soon as a person begins to make efforts, the cultivator begins to move in the right direction. Despite the fact that just as when digging the earth with a shovel, efforts are needed, processing in this way saves a lot of time, which means that forces.

Adjusting the depth of plowing

The depth of the plowing of the garden is determined by different factors. The specifics of the work by a motorbide are such that cutters can be immersed in cultivated land to different depths. They are buried themselves. In this case, the depth of processing depends on different points.

The speed of movement. If the unit is delayed in one place longer, it will become deeper, and vice versa. Therefore, the depth of processing is mainly controlled by the operator himself during operation. In reality, the depth of plowing is from 10 cm to 25 cm.

Also, adjustment of the depth of plowing by the cultivator can be limited using restrictive wheels. Some modocultivators have discs at the ends of the milling shaft limiting the depth of land cultivation.

Roader. All others use the missile for this, installed behind the body, before the operator. It has the degree of adjustment. At a certain maximum depth, the renewal rests on the ground, the unit hangs on it, and the cutters cannot go further further.

Also, the depth of processing depends on the total weight of the unit. Heavy weight presses the cutter down, contributing to the depth of processing. With lightweight, the motor.Cultivator seeks to move forward before the cutter has managed to plunge to a significant depth.

Therefore, an additional load is sometimes hung on a light unit, which is especially required on heavier soils.

Also, the depth of processing depends on three more reasons:

In loose soils, cutters quickly sit down during rotation. At the same time, the motor-cultivator sometimes gets stuck and cannot move forward, and you have to swing it across the axis to the left and right, then it is chosen by itself.

The depth in one place can be increased or reduced by lowering or raising cutters, resting the motor.Cultivator on the renewal.

Most mills from different manufacturers of a typical design. But there are varieties that differ in the shape of bends, the location of the cutting edges, etc.D.

As a result, some cutters are oriented to quickly move the unit forward, while not having time to plunge to a significant depth. Others, on the contrary, due to the specifics of the angles of attack (entrance to the ground), mainly work “to the depth”.

How to make a hand cultivator with your own hands

Everyone will be able to put on the handle a nozzle. We offer to build a hand cultivator with your own hands from a worthless bicycle and improvised means. It is better to take the wheel from a teenage tourist bicycle with a wide rim. Only the front wheel with a fork is used. The working part on the frame can be performed in any way. With teeth in 2 rows, stars or flat loop. The main thing is that in a homemade manual cultivator, the frame should be strong with fastening on the bolts of stiffness ribs, connection with handles created from simple or glued wood. Instead of wood, you can use light metal tubes. Convenient and light looser is indispensable for the processing of wide aisles, trunk circles of trees.

Another equally effective manual tool will be a manual rotary cultivator. The main nodes in the drawing:

• Working elements of a star or disks. 1;
• Axes for attaching work stars. 2;
• Bushings for collecting a node. 3;
• Connecting brackets, large and small. 5, 4;
• Frame stem that turns into a pipe and connected to a transverse handle. 6.7, 8.

Spherical discs, they are created by forming. But with the same success you can use the manual “hedgehogs”, and with their help to collect the working body. A detailed drawing of a hand cultivator with your own hands to help you.

Among the designs of homesproofs there are full.Fledged motoblocks created on the basis of chainsaws and other motor equipment. The value of these home.Made devices for the owner is that he used improvised means and created a tool for his needs. On the other hand, the cost of factory models does not always allow you to buy a cultivator from a well.Known reliable manufacturer. How else can you assemble a hand cultivator with your own hands, watch the video:

Review of models

Before acquiring a manual cultivator, it is necessary to familiarize yourself with its technical characteristics, make sure of the convenience and sufficient length of the handle.

Earthrobros

Manual cultivator Zemlyrobros is equipped with a wheel that helps to move the tool. Its base is made of quality metal.

There are 5 nozzles in the kit:

A manual cultivator of the dwarf is made of metal, equipped with removable elements for performing such types of work:

Flat

A manual cultivator Batrak is an advanced version of agricultural equipment, since it is equipped with a wheel and has interchangeable nozzles:

Its weight is about 4 kg. With its use, soil processing is much faster.

Miracle Lopat

The cultivator of the shovel for the cottage has a reliable and fairly simple design. Tool weight. 5200 grams. It is easy to work with a shovel due to the leverage system.

Moving step-0.1-0.2 m (depending on the density of the soil). Excitable processing width. 0.5 m. In the process of digging a summer cottage, it is recommended to carry out dug in rows, moving back forward, and moving the miracle-lopet.

Needle

Needle.Shaped cultivator. A type of star rotational. It is intended for loosening the soil and extermination of weed grass. The location of the cornflowing knife affects the cutting of the roots. Weighs equipment less than 2 kg.

Cultivator. Compact and inexpensive assistant for a summer resident. With its help, the care of the site is facilitated. Depending on the tasks, it is possible to choose the right model of the necessary configuration.