How to use a manual lawn mower in gasoline. Lawn haircut

Barrow care: proper operation of garden equipment. the key to its durability

To date, lawmakers for grass occupy an honorable place on the market for caring for sites and this is not surprising, since the optimal cost and high level of performance cannot leave indifferent most of the population of different countries. At the moment, different manufacturers have presented a huge amount of technology of this direction for public display.

The lineup is huge and diverse. But it is worth noting that gasoline gas mowers are in particular demand at manual control. The reason for this is a low cost. But also these tools have a number of shortcomings, which we actually talk about in this article.

over, the best models of hand mowers will be presented to your attention. And who knows, perhaps, and you will select the most optimal option for the “assistant” for your site. So, let’s start considering the topic.

How to start the device?

About how to properly start the engine, is written in detail in the instructions for the operation of the selected lawn mowing model, therefore, in a fully serviceable device, the launch of the motor does not cause difficulties.

If compliance with all the recommendations did not lead to launch, then either the engine or some additional equipment is faulty or incorrectly configured, so the braid needs to be maintained or repair.

You will find more detailed information on the malfunctions of mowers, as well as methods of repairing them in this article (malfunction of the gas mowing of gasoline).

If there is no instruction manual for the device, then you need to act as it is written below.

First, you need to carefully examine the mower to detect all the controls related to the engine, that is:

button or toggle switch on/off;
manual starter handle;
Electrostarter button;
Accelerator handle;
fuel pump button;
throttle control lever.

On inexpensive models of lawn mowers, most often there are almost all of these elements with the exception of the electric starter button, however, models are found without most of these elements or with an electric starter button.

On the most expensive models, there is usually only a tooth.on and off to turn off the engine, as well as the handle of a hand starter, all other elements operate in automatic mode and do not require the intervention of the operator.

Then perform the following sequence of actions (if there are no elements, then they work in automatic mode or you could not find them):

check the level of oil and the presence of gasoline;
turn on the switch.on and off to turn off the engine;
pump up fuel using the corresponding button;
translate the throttle control lever into launch mode or “OFF” position;
pull the hand starter cable until noticeable resistance appears;
Smoothly, but strongly and quickly pull the hand starter cable on yourself;
If the motor did not start, then repeat the 2-3 times the last 2-3 times;
If the motor still does not start, then it is necessary either to find the missing management elements, or to conduct its diagnosis in order to detect and eliminate the problem.

The difference in the launch of devices with an electric starter is only that instead of using a manual starter cable is pressed on the electric starter button and hold it pressed for 1-2 seconds.

The main purpose of the trimmer for grass

A trimmer for grass for grass is a tool that allows you to cut green grass with a soft stem or dry dry. If the lawn mower moves on the surface of the earth, then in this case the trimmer for the grass is fixed to the operator due to the presence of special belts.

It is worth noting that the device is universal. Many even believe that electric braids for grass are trimmers, but this.

The trimmer for the grass performs such actions sequentially:

Due to his actions, the operator will attach the tool with special belts and start the motor into the work. The launch method will depend on which drive of the device. It can be an electric or gasoline view. The first option is launched when the button is pressed, but the gasoline is turned on when using a manual starter;
The torque from the engine will be transferred to the spindle area or shaft. These are the very working bodies to which the head with a fishing line and a cutting steel circle is mounted;
The transfer of the torque from the motor to the working body will be carried out at the expense of a flexible or hard shaft;
The rotation of the drum with a fishing line or a disk equipped with knives will allow you to cut the grass or cut it off.

The main structural elements in the device are presented:

drive mechanism, t.e. an engine that can be both gasoline and electric;
a rigid base in the form of a bar, which connects the engine and the working organ;
the handle, in the design of the trimmer for the grass, it is customary to use 2 pens, one part of which is a place for the location of the accelerator;
a hard shaft, which gives the possibility of transferring a rotating moment from the engine to the executive body;
The defense casing is not only necessary for processing the protection of the operator’s legs, but also for a neat bevel of vegetation;
belt mounting, which make it possible to ensure reliable fixation of the device on operator shoulders.

Taking a question of how to choose a trimmer for grass grass, it is worth noting that the devices of a gasoline type are equipped with an additional fuel tank, when the electric form works exclusively with the support of the network. Therefore, instead of a tank, a network cord is presented in the second case.

How to use?

The main purpose of the lawn mower is a mowing young low grass on lawns and relatively even clearings, but sometimes you have to mow high grass or weeds, as well as cut the lawns on the slopes.

Even with the mowing of young grass, it is necessary to observe the correct sequence of actions, this will extend the service life of the parts of the lawn mower and reduce physical activity on the operator.

All actions performed during mowing can be divided into:

preparation for mowing;
selection of the mode of operation;
rectilinear movement;
turns;
stop;
emptying the grass receiver;
end of work;
Lugging a lawn mower.

Preparation for mowing

This operation is especially important after a long break or the operation of the lawn mower in a heavy mode for a long time.

Preparation for mowing includes:

visual examination of the mowing in search of visible defects, including poorly tightened bolts or nuts;
checking the oil level in the engine followed by valley or replacement;
checking the condition of the belt, gearbox and knife, followed by maintenance, that is, replacing, repair, sharpening or lubrication, if necessary;
check the state of all controls and their lubrication/maintenance if necessary;
check the level of gasoline, as well as its valve, if necessary;
Settling a folding handle under the growth of the operator.

All these procedures are described in detail in the operation manual, so you need to carefully read this document, as well as always keep it at hand in case of some emergency situations.

Lawn Mowing Alternatives. Reel Mower

In addition, on mowers whose wheels are attached to the frame with bolts, you need to make sure of reliable fixation of the wheels, as well as their free rotation, and if necessary, fix them or grease them.

Selecting the operating mode

After preparing for mowing and delivery of the lawn mower to the place of work, it is necessary to select the appropriate mode, that is, configure the height of the mowing and activate the method of processing and emitting mowed grass in this situation.On most models, the height of the mowing is regulated centrally, so it is enough to transfer the appropriate lever to the required position, however, the adjustment is carried out on each wheel individually to part of the mowing mowers.

This increases the time spent on the procedure, but allows you to set a knife at a certain angle, which is useful when working in areas with a complex relief.

The choice of each of the methods of processing and ejecting the mowed grass is described in detail in the instructions for operation, so it is necessary to carefully read this document, because the choice of one or another method depends on the design of the mower and is not always applicable even to the apparatus of one manufacturer.

Direct movement

The straightforward movement of non.self.propelled devices does not cause much difficulties, because the operator pushes them with the most comfortable speed for him. The situation with self.propelled braids is different, since their speed depends on the speed of rotation of the crankshaft of the engine and the gear ratio of the transmission.

On mowers with one transmission, the speed of movement is regulated by changing the speed of rotation of the engine shaft, however, for high.quality mowing grass, the turnover of the crankshaft should not decrease below 2.5–2.8 thousand per minute, which is only a little less than the maximum rotation speed.

If the shaft will spin slower, the knife will not be able to effectively and cut the grass evenly. Therefore, on mowers with a variator or multi.speed hydrostatic transmission, the transmission necessary for the optimal speed of movement is first set and only after that begin to move forward.

On any self.propelled lawn mowers, to start moving forward, the corresponding bracket is pressed on a folding handle.

Turns

The mower cannot turn it independently, so the turn always occurs due to the physical effect of the operator. In areas with low grass and large (5 or more meters) radius of rotation, it is enough at every step to little to turn the handle in the opposite direction.

However, in areas with high grass or if you need to turn (turn around) in a small space, you first have to press the handle to raise the front wheels and only then turn the device to the desired angle.

If you do not raise the front wheels, you will have to strain very much, because they create tangible resistance to the side movement.

In addition, on self.propelled braids before starting the maneuver, it is necessary to release the drive bracket so that during the turn the drive wheels are not connected to the engine. If you do not do this and turn it during movement, then the load on the transmission will sharply increase and its resource will be reduced.

Stop

If it is necessary to stop for a short time (for a few seconds, for example, to wipe sweat from the forehead), then it is enough to stop pushing the non.self.propelled apparatus or release the corresponding bracket of the self.propelled device.

However, if a stop for 20 seconds or more, then you need to release the knife bracket and use the accelerator to reduce the speed of rotation of the engine shaft to idle (900–1300 rpm depending on the engine characteristics).

This will reduce fuel consumption and increase the engine resource. If the stop for a minute or more, it is also advisable to drown out the engine so that it does not spend his resource idle.

Emptying the grass receiver

Some models of mowers are equipped with a grass receiver, that is, with a capacity in which all the beveled and crushed grass gathering. Most herbal receivers have an indicator of filling. a small window closed by a transparent glass through which it is clear how filled it is.

Rule. do not tighten with the last haircut before wintering

If the first haircut is recommended to be produced as soon as the height of young shoots reaches 10-12 cm, then with the last haircut you need to be extremely careful. Before you go to winter, you need to mow it at the usual height no later than at the end of September. If the autumn turned out to be warm, and the average daily temperature does not drop below 10 ° C, then the last haircut should be made in mid.October. Be sure to choose a calm day. After cutting, the ends of the blades are very vulnerable and sensitive. If a cold wind is blowing, it can frostbite. Before wintering, you can not remove the mowed grass from the site. She will protect him from severe frosts. Do not think that long grass is easier to endure cold. If you go to winter the gas with a height of the cover about 10 cm, then frostbitten plants will begin to bend to the ground, even more cooling the soil and deforming. And too high grass is subject to infection with snow mold.

How to use?

The main purpose of the lawn mower is a mowing young low grass on lawns and relatively even clearings, but sometimes you have to mow high grass or weeds, as well as cut the lawns on the slopes.

Even with the mowing of young grass, it is necessary to observe the correct sequence of actions, this will extend the service life of the parts of the lawn mower and reduce physical activity on the operator.

All actions performed during mowing can be divided into:

preparation for mowing;
selection of the mode of operation;
rectilinear movement;
turns;
stop;
emptying the grass receiver;
end of work;
Lugging a lawn mower.

Preparation for mowing

This operation is especially important after a long break or the operation of the lawn mower in a heavy mode for a long time.

Preparation for mowing includes:

visual examination of the mowing in search of visible defects, including poorly tightened bolts or nuts;
checking the oil level in the engine followed by valley or replacement;
checking the condition of the belt, gearbox and knife, followed by maintenance, that is, replacing, repair, sharpening or lubrication, if necessary;
check the state of all controls and their lubrication/maintenance if necessary;
check the level of gasoline, as well as its valve, if necessary;
Settling a folding handle under the growth of the operator.

All these procedures are described in detail in the operation manual, so you need to carefully read this document, as well as always keep it at hand in case of some emergency situations.

Selecting the operating mode

After preparing for mowing and delivery of the lawn mower to the place of work, it is necessary to select the appropriate mode, that is, configure the height of the mowing and activate the method of processing and emitting mowed grass in this situation.On most models, the height of the mowing is regulated centrally, so it is enough to transfer the appropriate lever to the required position, however, the adjustment is carried out on each wheel individually to part of the mowing mowers.

This increases the time spent on the procedure, but allows you to set a knife at a certain angle, which is useful when working in areas with a complex relief.

Direct movement

On any self.propelled lawn mowers, to start moving forward, the corresponding bracket is pressed on a folding handle.

Turns

If you do not raise the front wheels, you will have to strain very much, because they create tangible resistance to the side movement.

Stop

This will reduce fuel consumption and increase the engine resource. If the stop for a minute or more, it is also advisable to drown out the engine so that it does not spend his resource idle.

Emptying the grass receiver

What nozzle to use for mowing grass with a benzoca

The design of the gas station uses two types of cutting nozzles or milling. These are coils with fishing line, as well as steel or plastic disks. What is better to choose for work with a gas engineer. The site presents information on how to choose discs and fishing line for a trimmer for trimmers, as well as their types and design features. Briefly consider what types of cutting mills should be used on trimmers and benzocoses.

To prick soft grass, a fishing line for a trimmer is used, which is wound on a drum or coil.Lines for a trimmer, unlike metal disks, is used where the grass grows next to trees, houses, fences and other obstacles. The fishing line for a trimmer allows you to produce high.quality grass mowing near the obstacles, while without violating the design of the tool

The choice of cutting milling cutters depends on the location of the tool. If it is planned to work in the personal territory, then a fishing line for a trimmer is selected, and for injection of grass in the field or steppe, discs with 3-4 blades or more, as well as disks with small teeth are used.

It is interesting!In most cases, cutters are not equipped with an instrument, so the buyer can independently decide what he needs. a fishing line for a trimmer or a steel disk.

The chassis and height of the nobility

Wheels are an important element of the chassis of the lawn mower. Plastic or rubber rings can be used as tires, less often on professional models you can find pneumatic wheels. To improve patency by irregularities, large rear wheels are installed on some of the lawnmands.

Almost all lawnmands have a change in the height of the haircut. The lawn is not recommended to cut at a time for a large length (more than 1/3). There are a large number of systems for changes in the height of the mowing, usually 5-7 provisions are provided, on professional technology there may be more.

Lever system for changing the height of the spit

On most models near each wheel there is a lever that allows you to choose a haircut height. With a centralized system, all axes are moved to the right position using one lever. On simple electric braids, the wheels are simply removed and rearranged in other grooves.

How to mow a lawn mower

Any advertising represents a modern lawn mower, as a universal tool that can do a dozen mowers in an hour. In addition to high performance, the lawn mower allows you to get good quality of the lawn and successfully mow, regardless of qualifications, with a relatively slight physical exertion.But working as a lawn mower is not so simple, a certain machine control skill and good knowledge of the peculiarities of the terrain are required.

The basics of managing the lawn mower

In fact, any of the lawn mowers is a motor with a pair of sharp knives mounted on the engine shaft. The entire design of the motor shaft with the impeller is closed with plastic or steel protection and fixed on the wheel trim. Despite the relatively large weight of the unit, in theory, any adult without special physical training can mow a lawn mower. Nevertheless, mowing grass is not as easy as it can look on advertising.

For the correct and safe management of the lawn mower, you need:

Properly serve the device, adjust and prepare the lawn mower to work;
Well focus on the area of the mowing site. Before starting work, inspect the site and remove stones, large branches, any garbage that can break the cutting edge, knife and engine;
If there are flower beds or shrubs on the lawn, you need to think over the route of the lawn mower and place to unload the container with cutting grass in advance.

Safety precautions during work

Safety precautions when working with motorcycles are to fulfill the following requirements.

Do not use trimmers in the rain or with increased humidity.
People and animals should be at a distance of at least 15 m from the working device: trimming of grass, small garbage and stones fly out from under the cutting head at high speed and may injure.
It is better to put on the grass trimmer to a dense fabric that completely closes the arms and legs.
You need to work in protective glasses, gloves, headdress, closed shoes, special headphones or Berushas.
The wire of the network trimmer for the grass should be behind the mower.

Important! You can’t stretch your hand or foot to the cutting head!

So, the use of manual vehicles for mowing grass allows you to maintain order on a small area. It is more convenient to use a mower in vast areas. In addition, a trimmer for grass is relevant when harvesting hay and restoring order in the territory: small herbal scraps can be mulched strawberries and other useful plants. You can clearly see the mowing process with this tool on the video.

Is it possible to mow wet grass?

Despite the fact that mowing with wet grass does not pose a direct threat to the details of the apparatus, it is undesirable to mow it, because wet grass is noticeably heavier, which means that the air flow created by the knife will not be able to raise it as effectively as dry vegetation. If you need to urgently shake wet grass without waiting for its drying, then this must be done in several visits, as gradually possible reducing the height of the mowing, which will increase the time of mowing, but it will provide much higher quality.

Store lawn mowers in dry, well.ventilated rooms. For short.term storage, no preparatory actions are required, it is enough to roll the device to the place intended for it and fold the handle.

If the shelf life exceeds a couple of months, then the device must be prepared for which the following actions are performed:

Drain and oil drain

This operation is necessary for two reasons:

During long.term storage, combustible materials are lost part of their characteristics, so the engine is launched after long downtime with gasoline or oil that remained after the end of use this year can cause serious harm to the engine and reduce its resource.
If during the storage the device you have to turn it over or put vertically, then combustible materials can flow out, after which they will stain the floor and hull of the braid, fill the room with a heavy oil smell and pose a threat to the occurrence of a fire.

The method of draining these liquids depends on the design of the lawn mower and is described in detail in the operating manual.

If there is no manual, then the mitten should be put on the table (drainage materials are drained in this way only after the engine cooling), tilting to one side at an angle of 45 degrees and the fuel tank and the fuel tank from the bottom in search of drainage holes and the fuel. If they are not, then you first need to unscrew the lid of the fuel tank and turn the mower with the wheels up so that the glass is gasoline, then tighten the lid of the fuel tank.

Before draining oil, it is necessary, not including ignition, pull the manual starter 5-10 times, thanks to this, the oil pump will give grease to all the rubbing parts of the engine, as a result they will be protected from moisture to spring. Then you need to unscrew the lid of the pouring oil neck and turn the device again, waiting for the complete flows of the liquids, and then return the lid to its place.

Some models of mowers are equipped with engines, which manufacturers say that motors do not need to change the oil, but only in its valve. This is not a too honest statement, because the engine can work in the old oil, which is constantly added by new, but only a limited time, for example, 500 or 1000 hours.

This engine resource is just enough for the entire warranty period of operation declared by the manufacturer (usually 2–5 years), after which there is a large probability of a motor breakdown, while when changing the oil, the engine can operate 10–20 years without repair.

Therefore, to drain the oil in mowers with such a motor or not to drain, everyone will have to decide individually.

If high.quality oil corresponding to the SAE and other parameters is poured into the engine, then you can not only drain the old oil, but also fill the new one, but this procedure must be carried out on a hot engine, therefore it is applicable only where there is a special opening for this.

Then, in diesel fuel or gasoline, the oil filter is washed (if it is installed on the model and it can be washed) and the new oil is poured, after which, not including the ignition, twitch the manual starter cable 5–10 times to grease all the rubbing engine details.

Drying of the case

Proper maintenance involves washing the case after each use, which is why it is likely that droplets of water, remaining on the housing, will freeze and damage the LCP or rubbing parts. Therefore, before leaving the mower to long (winter) storage, it is necessary to carefully blow the body from all sides with the help of a blower, paying special attention to the joint of the wheel axes and bushings that perform the function of the bearing.

If the wheel axes are installed on the bearings, then it is necessary to carefully blow the bearings from all available areas to remove even the smallest moisture particles from them.

Preservation of rods and bearings

It is necessary to treat the inner surface of all cable drives (rods) with WD-40 liquid to remove water from them, and then pour 0.2-0.5 cm3 of motor oil into them using a syringe.

If this is not done, then after 3-5 years it is likely that the cables will begin to seize, which will lead to the impossibility of resetting the engine speed and other problems in time.

Some models of mowers provide for lubrication of bearings, including sliding (shaft-linen) through special tavotnitsa. Before winter, such bearings must be filled with a lubricant recommended by the manufacturer using a syringe for servicing (syringing) of the chassis of old cars.

Checking and sharpening a knife

The more acute the knife, the less the load on the engine, which means that the longer service life is longer. The most important condition for sharpening the knife is to preserve the balance, because if one side is more difficult than the other even by half a gram, this will lead to strong beats that negatively affect the resource of the crankshaft bearings.

To check the centering, the removed knife can be put on a 1-2 mm thick plate vertically fixed in a vise, if the balance is observed, then the balance will be achieved when the plate is exactly in the middle of the knife.

If it is shifted to the side, then when sharpening more metal is removed from this side, constantly checking the balance. You can also give a knife to sharpen a specialized workshop engaged in the repair and maintenance of gasoline lawners, or install a new one instead.

CRAFTSMAN M140 160-cc 21-in Gas Push Lawn Mower

Varieties of lawn mowers depending on the power unit

Types of lawn mowers by type of engine are limited by two options. electric and gasoline. Diesel engines in these machines (with the exception of some models of mini-tractors and riders) are not used due to large weight, complexity of the design and low rotation of the shaft rotation.

Electricosyles

Trammers for grass and lawn mowers with electric motors are very convenient in small areas near the house. They are productive, low.noise, light, do not require complicated maintenance. There are very few requirements during operation. The main ones are not recommended to mow wet grass and not overload the engine, it should work at stable speeds.

With large loads and a frequent decrease in rotation frequency, the engine overheats, which leads to its failure, and repairing such motors is expensive and difficult. In addition, the cable stretching behind the lawn mower or trimmer is not only inconvenient, but also limits the radius of the working area. If you have to mow between the trees, then it is better not to find a gasoline trimmer for grass.

Gasoline lawn mowers

On the basis of two and four.stroke gasoline engines, a lot of models of trimmers and wheel mowers are produced. For trimmers, two.stroke engines are usually used, as lighter, quite powerful and easy to maintain.

Wheel lawn mowers are equipped with both types of gasoline engines, depending on the size and the required performance. Basic mowing machines are characterized by a high level of autonomy, a significant resource (2.8,000 mothers), depending on the brand of the engine, maintainability. They are quite economical-even if you use high-quality fuel and brand stamps of oils (but it is not recommended to do otherwise), then the cost of operating gasoline lawn mower or a trimmer for grass will not exceed the costs of one or two travel by a distance of 150-200 km.

If you notice an error, not a working video or link, please select a text fragment and click Ctrlenter.

Practice for working on a lawn mower

Any complex technical device requires a certain time to get used to. If you did not have the practice of working with mowers of any performance, the first thing you need to study the instructions to clearly present which levers and pens are used to control the lawn mower and which. to adjust the haircut parameters. In addition, it will be necessary to learn how to set the position of the position of the cutting edge of the lawn mower so as to mow the grass with an even and neat layer, leaving 3-4 cm of vegetation throughout the entire site.

Adjustment and launch of the gas mowing motor

The maintenance and adjustment of the engine revolutions is considered the most difficult stage in the preparation of the lawn mower for work. Therefore, before entering into the fight against complex equipment, even having a certain experience, be sure to read and re.read the operating instructions. The typical procedure for preparing a new motor for work looks approximately as follows:

The lawn mower must be installed on a flat and solid surface, wrap all folding elements and handles in the working position. The lever of turning the drive on the wheels must be turned off. If the lawn mower is equipped with a spark shutdown system, be sure to bring it to the turned off state;
It is necessary to mow only a absolutely good lawn mower, so before starting the motor it is necessary to inspect it and make sure that there is no leakage of oil and fuel. With a glove with a glove, check the density of planting the chip on the candle and proceed to refueling with fuel and oil;
The refueling of liquids is performed according to measured probes, for the oil crankcase, it will be necessary to fill the lubricant along the middle measure, no more. If you pour, the liquid can be squeezed out of the ventilation hole or through the gasket;
Be sure to change the oil after running in. If you decide to use semi.synthetics, do not go to the mineral water, and vice versa. About the first 20-30 hours after running the motor, mow grass at medium and low speeds. The performance will be low, but in the end you will significantly win in the motor resource, after a couple of mowers you can mow in normal mode. What oil to pour in the lawn mower? High.quality mineral or semi.synthetics. The most correct ones will be to follow the manufacturer’s recommendations, and not follow the advice of the seller of motor oils.

Do not believe the fables of sellers and advertising slogans about the preliminary running of the engines at the enterprise. This procedure is fully performed at the enterprise only for powerful high.speed engines with a high degree of forcing.

The easiest way is to mow on high.octane unhealthy fuel, but only if you are 100% sure of the quality of gasoline. The engine of the lawn mower holds well and practically does not heat up. American and Chinese motors work normally on the A-92, European options can be more capricious in choosing gasoline. For two.stroke engines, gasoline is mixed with special oil in a ratio of 50: 1.

Run the motor in the following sequence:

Almost all models have the opportunity to mow and throw the grass into the grass collector, so we select a convenient place for parking of the lawn mower to remove and unload the box from the grass and re.equip the car or simply inspect if necessary if necessary. There will also be fuel, tools and spare candles.

Adjusting the lanes of the lawn mower

Before starting to mow, adjust the height of the knives above the ground level. Most often, the lifting of the mowing housing above the grass is exposed with one handle, less often two. for each pair of wheels, this helps to mow lawns with very dense and heavy grass.

The heavier the housing of the lawn mower, the lower the cutting edges can be located. Most often it is a value of 20-25 mm. Soft grass is good to mow at the low position of the cutting plane, for the hard and high one you have to adjust not only the clearance, but also the angle of inclination of the gas mowing housing.

The slope forward helps to compensate for the deviation of the mower back with too hard to press on the handle. Especially if the grass is wet. it is difficult to mow, the rear drive wheels can slip. For a front.wheel drive, such a slope only worsens the productivity of the mowing, passes appear, and the surface remains uneven.

Handle adjustment

Modern lawn mowers make it possible to adjust the position of the handle under any growth or features of the constitution and physique of man. The easiest way is to mow and direct the cart if the hands on the handle are at the level of the center of gravity of the case or higher by 2-3cm.

With a large mass of the lawn mower on the control handle, large efforts are quite large, so when choosing a model, choose a design with an aluminum or steel tubular frame.

This is especially true for front.wheel drive models of lawn mowers. Owners of braids with a leading front hand like to hang the front bridge, thereby reducing the thrust and adjusting the direction of movement of the machine, turning the body with the handle on the rear bridge in the right direction.

How to mow without gross errors

First of all, you need to mow, without making excess excess effort on the control handle. The lawn mower was designed without taking into account such overload to the rear bridge. For the option of a front.wheel drive mowel, this worsens the quality of the haircut. When working in the rear.wheel drive version, such “help” wears out a transmission and leads to the appearance of a pantry on the lawn, it becomes more difficult to mow. In addition, you can easily damage the knife, motor or mow grass along the ground.

The art of mowing a lawn mower comes with practice. Most often, the direction of movement is adjusted by moving the handle to the left or right. In particularly difficult cases, you can mow even along a complex trajectory, slightly tilting the body of the lawn mower to the right or right, increasing the clutch of the wheels on one side and weakening on the other. Management techniques are simple, but require practice and skills.

Manufacturers

When choosing oil, you should pay close attention to its manufacturer. It is better to choose a brand recommended by the manufacturer of the lawn mower. In the instructions for equipment, you can find information about the seasoned oil, the frequency of its replacement and recommendations for the choice of working fluid.

In addition, many manufacturers of lawn mowers produce their own oils that will need to be used to replace if you want to follow the guarantee for equipment. In addition, the instructions give the general characteristics to which the oil should correspond. When choosing fluid replacement, you need to focus on this list. This will allow you to choose oil that best meets the requirements of the manufacturer.

Among all companies that represent their products in the market are the best Shell Helix Ultra. These oils are popular in all countries. Shell experts have been working on the creation of a unique technology for the production of synthetic oil from natural gas for 40 years. The resulting product is characterized by an improved composition, which at the moment is not at the moment. The manufacturer adds the necessary additives to the basic composition, which allows you to get products with various characteristics. Such oil should be bought only at specialized retail outlets, since the main fakes are often found.

The company also represents quality products. Molly Laker. The manufacturer produces several commodity lines that have different goals. This assortment includes goods for caring for garden equipment. Such oils are designed for the long.term operation of trimmers and lawn mowers, their technical characteristics are developed in accordance with the features of modern technology and the recommendations of manufacturers.

Read Device Rotor Krn 2

Liqui Moly adds additive packages to the lawn mower, which are necessary to reduce wear of equipment and maintain engine cleanliness. The main advantage of such liquids is environmental friendliness, since they are created on a plant basis. Liqui Moly Oils comply with all environmental standards.

The Razhenmyr company produces good mineral lubricant material, which was specially designed for garden technology. This tool can be used to maintain 4-stroke engines with various cooling systems. Rasenmacher can only be used at positive temperatures. The manufacturer carefully developed and selected additives for his product. The result of such actions was a wide range of functionality:

Maintaining pressure in the system at a stable level;
Effective lubrication of all the necessary details;
Maintaining the viscosity of the oil during the entire service life, until the next replacement;
Ensuring excellent engine protection from natural wear;
The minimum speed of evaporation.

Features of the operation of lawn mowers with mulching function

The positive effect of the action of mulch is based on the process of rotting of cut grass. But in practice, everything does not always happen as the owner of the site. In some cases, crushed vegetation simply dries in the sun, turning into hay.

To prevent this, you need to follow the rules for making mulch:

Grinding should be done in cool weather. On hot sunny days, it is better to choose an early morning or late evening for this;
It is best to mulch the lawn in mid.spring or late autumn. During this period, the sewn lawn needs most of all to fertilizers for growth and development;
Do not make a beast in early spring. After frosts, herbal cover begins to grow rapidly. Some stems become tough, turning into poor.quality raw materials. After grinding, they do not rot, but dry, only interfering with the normal growth of the lawn;
You can not mulch the lawn immediately after the rain. Firstly, in such conditions, the quality of the haircut of the grass will be quite low. Secondly, when mowing wet grass, the knife and other parts of the lawn mower will succumb to increased exposure to corrosion.

To extend the operating time of the mulching knife, you need to carefully clean it from adhering grass. This will help protect the cutting organ from chemicals that make up mineral fertilizers for the lawn.

A cheap way to create an elite lawn

According to some sources, mulching was invented by English gardeners. When it was forbidden to use watering hoses, they began to cover the green lawns with crushed vegetation.

Today it is called the mulching of lawns. It includes several procedures:

Thanks to this, the temperature balance is regulated on the lawn in the cold season. Moisture delayed during the hot summer. Soil feeding with useful substances. Territory protection from weeds.

Having carefully examined the basic plant zone, you can notice how it develops successfully and bothers. In addition, the sod layer becomes much thicker and denser. Indeed, at all times, high.quality fertile soil was the key to the prosperity of green spaces.

In regions where harsh winters prevail, it is advisable to create a thick layer of turf on the lawns.

Sources:

https://ltruck-service.ru/obsluzhivanie/konstruktivnye-elementy-gazonokosilok-i-travokosov.html
https://gc-ug.ru/selhoztehnika/kak-polzovatsya-gazonokosilkoj-benzinovoj.html
https://1-tools.ru/dlya-izmereniya/kak-polzovatsya-gazonokosilkoj-benzinovoj.html
https://minitraktor34.ru/kommunalnaya/kak-polzovatsya-gazonokosilkoj.html
https://zemlyaselhoz.ru/kosilki/kak-polzovatsya-gazonokosilkoj-benzinovoj.html
https://hitech-online.ru/tehnika-dlya-sada/trimmer/kak-polzovatsya-dlya-travy.html
https://pro-vnedorozhniki.ru/raboty-v-pole/kak-polzovatsya-gazonokosilkoj-video.html
https://gp-prsmah.ru/servis/kak-polzovatsya-gazonokosilkoj-benzinovoj.html
https://gp-prsmah.ru/servis/chto-takoe-mulchirovanie-v-gazonokosilke.html

Lawn Mowers gasoline, haircut, lawn, manual, mower