How to Wind a Fishing Line On a Huter Video Trimmer

Despite the fact that gardening equipment has been used for a long time, for some owners of private houses it is still a novelty. That is why often questions arise about how to properly wind a line on an electric or gas trimmer.

This is essentially a simple operation, but all its stages must be performed correctly to achieve the desired result. Moreover, in the operating instructions, only a few manufacturers give an answer to this urgent question. Study the article and find out how the line is wound around the reel of the trimmer.

The procedure for winding fishing line on the trimmer reel

First of all, you should know that trimmers have different working nozzles. The reel can be designed for different lengths and thicknesses of fishing line – this point should be considered when purchasing supplies.

So, how do you charge the fishing line into the trimmer coil? All work is divided into several stages:

1. First you need to disassemble the trimmer head.
2. Unscrew the nozzle by rotating the drum to the right.
3. Press your fingers on the two latches located on opposite sides of the slots, and remove the top cover of the nozzle. You can pry the cover with a screwdriver. This should be done carefully: the reels with automatic line feed have a spring, which can forcefully drop the lid along with all the contents of the reel.
   
4. Remove scraps of old fishing line.
   
5. Now you need to find the middle of the fishing line. To do this, rewind it to the required length (for example, 10 m), cut and fold in half.
6. Hook the middle of the fishing line into an existing recess or insert it into the hole specially designed for this. And start winding. The direction is indicated by the arrow, which is usually applied to the body of the trimmer coil (usually against the rotation of the drum). Some models have a double-sided reel: in this case, the fishing line should be wound in different directions: one end – in one direction, the other – in the other, while the loop of the fishing line must be brought into the dividing slot located in the middle.
7. Leave the loose ends of the fishing line about 20 cm long each. Later they will need to be fixed in the recesses.
   
8. And finally, the last step will be drum assembly. Replace the washers and spring. On the upper ring of the reel there are two recesses where you need to fill the antenna line of the fishing line. Pass them through the holes and install the reel in the drum, trying to tighten the fishing line and not displace the spring.
9. Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, the excess fishing line will be cut off by the cutting blade itself.

As you can see, it is easy to wind the line onto the reel of the trimmer: the main thing is to do everything right. And here are some more tips that will be useful to you when choosing a fishing line, its winding and subsequent work:

Video: How to Wind a Fishing Line On a Huter Video Trimmer

• Fishing line is of different thickness and with different cross-section. The best option for winding is the "native" for this model of fishing line;
• Never use a fishing line or metal cables for the trimmer. Such a replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawn mower, but also others;
• The fishing line is cut off when the working trimmer comes into contact with solid objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and rewind the fishing line onto the reel;
• Use a straight line for mowing grass and a pigtail line for coarse weeds. It is more durable and will not be permanently cut.

Despite the fact that gardening equipment has been used for a long time, for some owners of private houses it is still a novelty. That is why often questions arise about how to properly wind a line on an electric or gas trimmer.

This is essentially a simple operation, but all its stages must be performed correctly to achieve the desired result. Moreover, in the operating instructions, only a few manufacturers give an answer to this urgent question. Study the article and find out how the line is wound around the reel of the trimmer.

The procedure for winding fishing line on the trimmer reel

First of all, you should know that trimmers have different working nozzles. The reel can be designed for different lengths and thicknesses of fishing line – this point should be considered when purchasing supplies.

So, how do you charge the fishing line into the trimmer coil? All work is divided into several stages:

1. First you need to disassemble the trimmer head.
2. Unscrew the nozzle by rotating the drum to the right.
3. Press your fingers on the two latches located on opposite sides of the slots, and remove the top cover of the nozzle. You can pry the cover with a screwdriver. This should be done carefully: the reels with automatic line feed have a spring, which can forcefully drop the lid along with all the contents of the reel.
   
4. Remove scraps of old fishing line.
   
5. Now you need to find the middle of the fishing line. To do this, rewind it to the required length (for example, 10 m), cut and fold in half.
6. Hook the middle of the fishing line into an existing recess or insert it into the hole specially designed for this. And start winding. The direction is indicated by the arrow, which is usually applied to the body of the trimmer coil (usually against the rotation of the drum). Some models have a double-sided reel: in this case, the fishing line should be wound in different directions: one end – in one direction, the other – in the other, while the loop of the fishing line must be brought into the dividing slot located in the middle.
7. Leave the loose ends of the fishing line about 20 cm long each. Later they will need to be fixed in the recesses.
   
8. And finally, the last step will be drum assembly. Replace the washers and spring. On the upper ring of the reel there are two recesses where you need to fill the antenna line of the fishing line. Pass them through the holes and install the reel in the drum, trying to tighten the fishing line and not displace the spring.
9. Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, the excess fishing line will be cut off by the cutting blade itself.

As you can see, it is easy to wind the line onto the reel of the trimmer: the main thing is to do everything right. And here are some more tips that will be useful to you when choosing a fishing line, its winding and subsequent work:

• Fishing line is of different thickness and with different cross-section. The best option for winding is the "native" for this model of fishing line;
• Never use a fishing line or metal cables for the trimmer. Such a replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawn mower, but also others;
• The fishing line is cut off when the working trimmer comes into contact with solid objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and rewind the fishing line onto the reel;
• Use a straight line for mowing grass and a pigtail line for coarse weeds. It is more durable and will not be permanently cut.