How to Wind a Line on a Gas Trimmer

how to wind a new fishing line on a reel on the interskol lawn mow? | Topic Author: Daria

Irina Coils are different on trimmers, respectively, differently wound fishing line in them.

Love according to "you take 8-12-19 m of coil power and stretch this length in half starting from the loop, try to wind the line into your channel (there are two of them there from the slot, the direction of winding the branches is indicated.
http://www.fams.ru/pics/m400.jpg

Gennady trimmer patriot380 how to properly refill a fishing line? one end breaks during operation.

Tags: How to correctly wind the line onto the lawn mowing reel

How to wind a fishing line on a mowing head of a lawn-mowing (trimmer)

How to Wind a Line on a Gas Trimmer

How to wrap fishing line on a spool of a reel? | Topic Author: Homemade

How to wrap fishing line on a spool of a reel?
TIPS OF PROFESSIONALS

In pursuit of the casting range, fishermen use a lot of tricks:
use longer rods, put the thinnest fishing lines, go to reduce
the number of bites, increasing the mass of the sinker and forgetting about this at first
glance at a trivial matter, like the correctness of winding fishing line on a spool of a reel.

Responsible coil manufacturers usually provide simple circuits of the right
winding. But who reads these instructions?
In half the cases, they take a reel of fishing line and simply rewind it to fishing
reel.
Nevertheless, it is worthwhile to make a little work and achieve high-quality winding.
And she, in turn, will provide a casting distance close to maximum
and will prevent the self-resetting of fishing line loops, often leading to the appearance of a “beard”.
In addition, due to the smaller kink on the rim of the spool, the fishing line will last longer.
The most rare situations when the capacity of the spool is less than the length of the wound
fishing line, or when fishing line is wound from a large reel. 500 m and more.
It is enough to wind so much fishing line so that it does not reach the side
2-4 mm spools. and no problem.
If it is wound up flush with the sides, then the reel often itself will make the angler
to correct the correct winding: two or three drops of fishing line loops and the subsequent “beards” will force them to take a knife and remove excess.
Now fishing lines are becoming thinner and stronger, and the least problems arise
when the capacity of the spool is much higher than necessary.
The best solution would be to make cork or solid inserts
polystyrene foam, but, alas, many can not do it.
But still relatively recently, many manufacturers completed coils
such useful accessories. Therefore, you have to wind up under the main fishing line
backing. As it is best to use fishing line with a diameter of 0, 25-0, 3 mm.
Thinner is also suitable, but it will take too much, but from the fishing line
with a diameter of 0, 4 mm and more it is better to refuse, since “humps” remain from it
and dips even on reels with good styling.
If winding is needed under a very thin fishing line, for example for match fishing
or UL. spinning, then the upper part of it can be done with fishing line 0, 15-0, 2 mm.
You should not use kapron as a backing, and even more so
cotton thread: getting wet (and this is inevitable when fishing), it takes too long
dries.

READ  Criteria for Selecting Drives for Trimmers and Instructions for Replacing Them

Видео: How to Wind a Line on a Gas Trimmer


How to determine how much fishing line is needed for reeling?

Very simple. First, the required amount of fishing line is wound on the spool (usually 100 m, but there may be options), and on it. backing, not reaching the edge of the spool rim all the same 2-4 mm.
Thus, the correct winding will be obtained, but in a mirror version; it can be
rewind on a spare spool similar in capacity.
If this is not the case, you will have to rewind the fishing line twice to any other reel
(even Nevskaya will do), and then to the worker.

Knots for attaching fishing line to the reel It is not necessary to tie a fishing line for reeling, since
tubercle; the first turn is better to glue with a piece of adhesive tape, as, indeed, the last one.
By the way, do not forget to tie the main fishing line. there is a special node for this
(fig. 1).

READ  How to Set the Ignition On The Stihl 130 Trimmer

I prefer to attach the fishing line to the spool using a long loop (Fig. 2). Firstly, such a mount is self-tightening and under load the whole
an array of fishing line never rotates on a spool, even a metal one.
And secondly, if necessary, the unit can always be dissolved to replace the fishing line or
for extra backing.
Winding backing needs to be rather tight otherwise, when wet, it will become loose and when
long range casting the lower turns of the fishing line will fall into the winding.
And the main fishing line should be wound on a reel with a certain effort
the same reason.
Often, fishermen have a question: how to rewind fishing line from a spool to a reel? In my opinion, this can be done as you like: anyway, after the first few
casting line will twist in this way and as much as the whole
system. bait, line stiffness, reel roller and spool diameter. The most unpleasant problem that is typical for most coils with a rocker drive of the spool is the formation of hollows and “humps” from the fishing line (Fig. 3), which very negatively affects the casting distance. This effect cannot be overcome radically. uneven stroke of the spool
constructively, but every fisher is capable of improving the winding.
To do this, apply the method of mirror winding backing (Fig. 4) and the bottom,
non-working area of ​​the fishing line (usually 30-50 m).
The method consists in the fact that in the place of the "humps" hollows are made and vice versa.
Mirror winding has to be done manually; it’s a pretty painstaking job
from the first yes and from the second or third time to achieve more or less decent
The result is not always successful.
However, the game is worth the candle. line quality on most reels
improves significantly.
Another point worth paying attention to. storage of fishing line on a reel.
Usually it looks like this: after the last fishing, the reel is put away for storage,
and at the beginning of the next season it suddenly turns out that the fishing line began to tear,
like a rotten thread.
This is especially characteristic of monofilaments, substantially less. for "braids",
but any fishing line, if it is not supposed to be changed, can and should be saved
as good as possible.
To do this, carefully wrap the entire fishing line from the spool before winter storage.
(without touching the backing) to the floor, let it dry and rewind it not tightly again.
Additionally, I still wrap the spools with the fishing line newspaper. she prevents
accidental damage to the fishing line and, if moisture remains in the winding, dries it.
Before the start of the season, it is enough to rewind the line with the necessary effort.
In principle, such an operation will not be superfluous even after each fishing, only in this
in case you should dry a piece of fishing line a little longer in length than it was
maximum casting distance.

READ  How to Customize Turnovers on a Stihl Trimmer

Now fishing lines are becoming thinner and stronger, and much more common
situation when the capacity of the spool is much higher than necessary.

Andrey Kashtanov Based on materials "Fish with us"
#Fishing reels