How to Wind a Line on a Stihl Fs Trimmer

How to Wind a Line on a Stihl Fs Trimmer

Guaranteed production of a factory trimmer refill will inevitably require replacing the fishing line. Having a very rough idea of ​​how to fill the fishing line into the reel of the trimmer yourself, beginners are reluctant to take up this matter. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible.

Preliminary preparation

First of all, for winding fishing line it is required to remove the reel (bobbin, spool) from the trimmer – specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers with a working arrangement of the engine and the coil in the lower part, as a rule, have side keys on both sides of the bobbin. By pressing them simultaneously, the upper part of the reel, together with the internal contents for winding the fishing line, is disconnected, while the lower one remains on the trimmer. It is advisable to disassemble the bobbin on an even smooth place so that the spring included in the design does not pop out and is not lost;
  • Electric and gasoline trimmers with a curved rod without the possibility of installing a knife, as a rule, have coils with a special wing: in such designs, you should hold the spool in one position with one hand and rotate the locking reel on the wing nut with the other counterclockwise. After disconnecting the nut, the entire reel is removed.
  • Electric and petrol trimmers with the possibility of installing a knife on a straight bar (for example, Stihl trimmers) have a hole under the bobbin. For the motion of the rod to be stationary, a screwdriver or other suitable object is inserted into this hole and with a slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body scrolls clockwise (with the left thread) and is removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in various ways. In bobbins with a lamb, a lamb is twisted, in coils with latches, latches-clamps are pressed and one part of the coil is released from the other. If the halves of the spool are threaded, it is enough to turn them by hand in opposite directions until they are completely unscrewed.

We carry out winding fishing line

Slowly completed disassembling the spool reel without losing its spare parts allows you to go to the main task – winding fishing line into the reel. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working antenna

The simplest option and a simple sequence of actions:

  1. The dimensions of the bobbin and the length of the original factory winding determine the recommended fishing line length for winding – 2 … 5 m.
  2. One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  3. The fishing line is wound on the drum in the reverse direction of rotation of the spool on the trimmer product – as a rule, on the inner side of the bobbin an arrow indicates which direction the winding is going.
  4. A small section of fishing line is left free to bring it out – it is fixed in a specialized groove on the inside of the reel, designed to hold the winding when assembling the spool in working condition.
  5. The left end of the line is passed through the hole on the outside of the bobbin.
  6. The bobbin halves are assembled and put on the bar of the trimmer.

Coil with two working antennae

In this type of spools, you should determine the number of grooves for winding fishing line lying on the inside of the reel:

  • One groove – both antennae are wound together along one groove;
  • Two grooves – each antennae is wound on an individual groove.

For both cases, a 2-3-meter-long fishing line is taken. In single-groove reels, the fishing line is pulled into the through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the side of the bar – the correct direction of winding is usually indicated inside the arrow. In the presence of fixing grooves, the ends of the fishing line are threaded into them or held by the fingers of their free hands, threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the bar of the trimmer.

The difference between winding fishing line in two-groove reels is that initially a piece of fishing line 2-5 m long is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each in its own groove, the fixation of the antennae and the reel assembly are similar to the one-groove variant discussed above.

The first implementation of this procedure may seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to put the fishing line into the reel of the trimmer and wrap it correctly – this operation is not difficult and with some patience will certainly succeed:

Automatic reeling of fishing line

There is a variety of coils in which the automatic mechanism makes winding on its own – from the user it is enough just to properly fill the line. The fishing line is passed through the hole on the inside of the case, its antennae without winding is passed through the hole on the external case, the spool is assembled, and when the winding button is rotated, the line inside is wound up independently. In such a spool, it is impossible to make the winding incorrectly: the mechanism itself will determine the correct direction, since it can only turn in one direction.

How to thread fishing line into the trimmer coil? Video instruction

Guaranteed production of a factory trimmer refueling will inevitably require fishing line replacement. Having a very indicative idea of ​​how to put fishing line into the reel of the trimmer without the help of others, newcomers take up this matter without hunting. How to wind a fishing line onto a trimmer coil, how to thread a fishing line into a trimmer coil. Autocut for stihl fs 55 trimmer threading fishing line into the trimmer reel 2 part winding fishing line on. But with some abilities, mastering this simple science does not present any difficulties, and the similar annotation presented below will greatly facilitate this process.

Preliminary preparation

First, to wind the line, you need to remove the reel (bobbin, spool) from the trimmer – certain actions will depend on the difficulty of configuration and the type of product itself:

  • Small electronic trimmers with a working arrangement of the motor and coil in the lower part usually have side buttons on both sides of the bobbin. By pressing them simultaneously, the upper part of the reel, together with the internal contents for winding the fishing line, is disconnected, while the lower one remains on the trimmer. It is better to create a bobbin analysis on an even, smooth place, so that the spring included in the design does not pop out and is not lost;
  • Electronic and gasoline trimmers with a curved bar without the ability to install a knife, usually have coils with a special lamb: in similar designs, you should hold the spool with one hand in a stationary position, and turn the lamb nut on the bar counterclockwise with the other. How to fill the line in the trimmer? How to refill a fishing line into a trimmer reel. It’s clear how to charge the fishing line with a trimmer. After disconnecting the nut, the entire reel is removed.
  • Electronic and petrol trimmers with the possibility of installing a knife on a straight bar (for example, Stihl trimmers) have a hole under the bobbin. For the motionlessness of the rod, a screwdriver or other suitable object is inserted into this hole and during leisurely rotation, such mutual placement is achieved when the screwdriver enters the inside of the hole and the bobbin is fixed. After that, the coil body scrolls clockwise (with the left thread) and is removed from the trimmer.

Video: How to Wind a Line on a Stihl Fs Trimmer


For the second and third versions, the coils, depending on the design, are disassembled by different methods. In bobbins with a lamb, a lamb is turned out, in coils with latches, latches-clamps are pressed and one part of the coil is released from the other. How to refill a fishing line in how to properly cheap fishing line. 2. At your site. If the halves of the spool are threaded, it is enough to turn them by hand in the opposite direction until they are completely unscrewed.

How to replace the fishing line in the mowing head, STIHL FS 55 lawn spool

How to put a fishing line in a Stihl.FS-38 mower

Took the mower from the barn, and fishing line it was not there, I had to put fishing line and on occasion took off a little

We carry out winding fishing line

Slowly completed disassembling the spool reel without losing its spare parts allows you to go to the main task – winding fishing line into the reel. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working antenna

The most common option and easy sequence of actions:

  1. The dimensions of the bobbin and the length of the unique factory winding determine the recommended fishing line length for winding – 2 … 5 m.
  2. One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  3. The fishing line is wound on the drum in the reverse rotation of the spool in the trimmer product direction – usually, on the inner side of the bobbin, an arrow indicates which direction the winding is going.
  4. A small section of fishing line is left free to bring it out – it is fixed in a special groove on the inside of the bobbin, designed to hold the winding when assembling the spool in working condition.
  5. The left end of the line is passed through the hole on the outside of the bobbin.
  6. The bobbin halves are assembled and put on the bar of the trimmer.

Coil with two working antennae

In this type of spools, you should find the number of grooves for winding fishing line lying on the inside of the reel:

  • One groove – both antennae are wound together along one groove;
  • Two grooves – each antennae is wound on a personal groove.

For both cases, a 2-3-meter-long fishing line is taken. In single-groove reels, the fishing line is pulled into the through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the side of the bar – the correct direction of winding is usually indicated inside the arrow. In the presence of fixing grooves, the ends of the fishing line are threaded into them or held by the fingers of their free hands, threaded into the through hole of the outer half of the bobbin, the spool is locked and attached to the bar of the trimmer.

The difference between winding fishing line in two-groove reels is that initially a piece of fishing line 2-5 m long is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each in its own groove, the fixation of the antennae and the reel assembly are similar to the one-groove variant discussed above.

The first implementation of this procedure may seem long and rather laborious, but over time and experience this task will be solved much faster and easier.

The video below will clearly show how to put the fishing line into the reel of the trimmer and wrap it correctly – this operation is not difficult and with some patience will certainly succeed:

Automatic reeling of fishing line

There is a variety of coils in which the automatic mechanism produces winding without the help of others – it is quite enough from the user to correctly refill the fishing line. How to thread fishing line into the trimmer coil? Video instruction. How to remove the coil from the trimmer? How to wind a fishing line in order to refuel a fishing line. The fishing line is passed through the hole on the inside of the case, its antennae is wound through the hole on the outside of the case without winding, the bobbin is assembled, and when the winding button is rotated, the line is wound from the inside without the help of others. In such a spool, it is unrealistic to make winding erroneously: the mechanism itself will determine the correct direction, since it can only rotate in one direction.

Guaranteed production of a factory trimmer refill will inevitably require replacing the fishing line. Having a very rough idea of ​​how to fill the fishing line into the reel of the trimmer yourself, beginners are reluctant to take up this matter. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible.

Preliminary preparation

First of all, for winding fishing line it is required to remove the reel (bobbin, spool) from the trimmer – specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers with a working arrangement of the engine and the coil in the lower part, as a rule, have side keys on both sides of the bobbin. By pressing them simultaneously, the upper part of the reel, together with the internal contents for winding the fishing line, is disconnected, while the lower one remains on the trimmer. It is advisable to disassemble the bobbin on an even smooth place so that the spring included in the design does not pop out and is not lost;
  • Electric and gasoline trimmers with a curved rod without the possibility of installing a knife, as a rule, have coils with a special wing: in such designs, you should hold the spool in one position with one hand and rotate the locking reel on the wing nut with the other counterclockwise. After disconnecting the nut, the entire reel is removed.
  • Electric and petrol trimmers with the possibility of installing a knife on a straight bar (for example, Stihl trimmers) have a hole under the bobbin. For the motion of the rod to be stationary, a screwdriver or other suitable object is inserted into this hole and with a slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body scrolls clockwise (with the left thread) and is removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in various ways. In bobbins with a lamb, a lamb is twisted, in coils with latches, latches-clamps are pressed and one part of the coil is released from the other. If the halves of the spool are threaded, it is enough to turn them by hand in opposite directions until they are completely unscrewed.

We carry out winding fishing line

Slowly completed disassembling the spool reel without losing its spare parts allows you to go to the main task – winding fishing line into the reel. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working antenna

The simplest option and a simple sequence of actions:

  1. The dimensions of the bobbin and the length of the original factory winding determine the recommended fishing line length for winding – 2 … 5 m.
  2. One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  3. The fishing line is wound on the drum in the reverse direction of rotation of the spool on the trimmer product – as a rule, on the inner side of the bobbin an arrow indicates which direction the winding is going.
  4. A small section of fishing line is left free to bring it out – it is fixed in a specialized groove on the inside of the reel, designed to hold the winding when assembling the spool in working condition.
  5. The left end of the line is passed through the hole on the outside of the bobbin.
  6. The bobbin halves are assembled and put on the bar of the trimmer.

Coil with two working antennae

In this type of spools, you should determine the number of grooves for winding fishing line lying on the inside of the reel:

  • One groove – both antennae are wound together along one groove;
  • Two grooves – each antennae is wound on an individual groove.

For both cases, a 2-3-meter-long fishing line is taken. In single-groove reels, the fishing line is pulled into the through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the side of the bar – the correct direction of winding is usually indicated inside the arrow. In the presence of fixing grooves, the ends of the fishing line are threaded into them or held by the fingers of their free hands, threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the bar of the trimmer.

The difference between winding fishing line in two-groove reels is that initially a piece of fishing line 2-5 m long is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each in its own groove, the fixation of the antennae and the reel assembly are similar to the one-groove variant discussed above.

The first implementation of this procedure may seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to put the fishing line into the reel of the trimmer and wrap it correctly – this operation is not difficult and with some patience will certainly succeed:

Automatic reeling of fishing line

There is a variety of coils in which the automatic mechanism makes winding on its own – from the user it is enough just to properly fill the line. The fishing line is passed through the hole on the inside of the case, its antennae without winding is passed through the hole on the external case, the spool is assembled, and when the winding button is rotated, the line inside is wound up independently. In such a spool, it is impossible to make the winding incorrectly: the mechanism itself will determine the correct direction, since it can only turn in one direction.

A gasoline or electric trimmer is an excellent assistant when processing a garden plot. But, like other equipment, it requires attention and certain care.

The first step is to disassemble and remove the trimmer head. To do this, push the locks all the way to the sides of the case and turn them clockwise.
To open the mowing head, press the side latches, if you can’t do it with your hands, you can use a screwdriver. Remove the coil.
For the right choice of fishing line, suitable specifically for your trimmer, look at the inside of the numeric notation.

These numbers indicate the required diameter of the fishing line in millimeters.

If you did not find such information, then the maximum diameter can be determined by taking the fishing line and threading it through the hollow hole. The thread should pass freely back and forth.