How To Wind The Line On The Trimmer Reel Semiautomatic

How to wind the line onto the trimmer spool

The trimmer is a great solution for those who have a large garden or lawn near the house, which needs to be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, it will become necessary to replace certain elements, and this will have to be learned.

How can this be done? To replace the main cutter, you must first select it correctly. In principle, the lawn mower instruction manual should indicate the diameter of the thread to be used in it.

When you have acquired the required cutting element, try to install it correctly. It should be noted that there are a huge number on the Internet. Which will help you figure out how to properly thread the line into the trimmer spool.

How to change line to trimmer

Below we have provided Step-by-step instructions for replacing a whine trimmer.

The first thing to do is unplug the tool and turn off the engine. Then you need to remove the trimmer head. This can be done by using a simple screwdriver, lowered it into the hole of the gearbox to prevent the shaft from turning. And then just Unscrew

They are usually unscrewed in a clockwise direction, but different models have different mechanisms, so it may be necessary to twist in the opposite direction. But if suddenly, for some reason, you cannot figure it out, then we strongly recommend that you refer to the user manual to understand how to disconnect it

Second. After removing the mowing head, open it. This can be done by means of clamps, which are located opposite each other. Pressing on them, you can remove the head cover, and then pull out the spool on which the fishing line is wound. By pulling it out, you can determine what type it belongs to. There are bobbins one-piece and two-piece

We analyze how to thread the line into the trimmer spool in two versions

So, option one. load the fishing line into a single-section reel. The prepared piece of thread is folded in half and pushed into the spool. Then, we begin to wind both ends in the same direction, which will be indicated by the arrow on the spool. At the end of the winding, do not forget to check that the different ends of the thread are looking in different directions.

Option two. winding the line with a two-piece reel. The pre-prepared thread is divided into two parts, and its ends, must be fixed: this must be done by placing them in special fasteners

Winding is carried out, as in the first case, along the arrow indicated on the spool. Both segments must be wound so that they do NOT overlap. Further, the ends of the thread must be fixed in the grooves and spread on opposite sides.

The spring is then inserted into the reel and the whole thing is placed in the mowing head. When placing the coil in the trimmer you need to gently hold the spring parallel to insert the line into the cut of the mower head. And in the end, it just needs to be secured with the final part, that is, with a lid.

After threading the trimmer, you need to check it. If you did everything correctly, everything will work, but if you make a mistake, we recommend that you read the article again, or even better, if you look at how to install the line on the reel in the trimmers.

How to remove the line from the trimmer spool

Over time, the cutting element of the head wears out, and it becomes necessary to pull out the remnants of the old line. But not everyone knows how to do it. Our step-by-step instructions plus how to pull the thread from the trimmer spool, which you can find on the net, will help in solving this issue.

The mowing head must be disassembled

Remove the cover using the clips

Cleaning up the remnants of cutting material

Complicated? Of course not. But if, nevertheless, doubts creep into you that for some reason you will NOT be able to do this, then of course find and see how to pull out or how to wind the thread onto the spool of the lawn mowers.

How to replace the line with an electric trimmer

In fact, it makes no difference which oblique you use, be it electric or gasoline. Threading is the same. The only difference is that if you use a gasoline scythe, you get more freedom, since it is NOT limited by the cable, which is present on the electric scythe

Yes, do not hesitate to use special rollers for installing or threading the line in an electric scythe, which can teach you much faster than simple reading.

Removing the coil from the trimmer

On small electric trimmers with a bottom-mounted motor (when it is in the ground while working), the reels usually have two keys on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to grab the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the Trimmer Bar. Having unscrewed the lamb, carefully remove the entire coil, trying NOT to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver does NOT crawl even deeper and the coil will lock. Now steep the whole coil clockwise (since the thread is left-hand) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using snaps or a twisted lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection between the two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you also need to make sure that the spring inside is not lost.

How to properly wind the line on the trimmer spool

Many, having worked out the factory line on the recently purchased trimmers, are trying to wind a new one, but they cannot, because they do not know how to properly wind the line on the spool (bobbin) of the trimmer. It seems that there is an instruction, but it still does not work. Let’s try in this article to deal with this issue.

So, in order to wind the line, you first need to remove the coil from the trimmer. this will be more convenient. The removal method will depend on the type of trimmer.

than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a hole on the inside of the reel for the fixing line, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. I wound the fishing line, we leave a small piece of it unwound to put it out. We fix this piece in a specially groove located on the inner part of the reel and designed so that at the time of collecting the reel, the line does NOT unwind. If there is such a groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and threading the outer piece of fishing line into the existing hole, collect and put the coil back on the trimmer.

If the coil is designed to work with two tendrils, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. Reels with one groove should have a through hole through which the fishing line is threaded. We rewind 2-4 m of fishing line, threading it through this hole so that the fishing line sticks out equally on each side. And we simultaneously wind both tendrils of the fishing line in one direction, opposite to the direction of rotation of the coil to the trim tabs and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, the resulting ends We fix in the Special grooves, and if they are not there, we hold them with our fingers. Threading both ends into the existing holes on the outer casing of the coil. We collect the coil and fasten it to the trimmers.

If there are two grooves, fold a piece of fishing line 2-4 m long in half. Insert the loop obtained at the place of the fold into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also spools in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, and not winding, are threaded completely through the holes on the outer body of the reel, assemble the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Turning the button. the line itself is wound inside. In this case, twisting it in the “wrong” direction will NOT work, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!

How to properly wind the line on the trimmer spool?

Despite the fact that gardening equipment has been used for quite some time, it is still a novelty for some owners of private houses. That is why there are often questions about how to properly wind the line on an electric or gasoline trimmer.

This is essentially a simple operation, but all its stages must be performed correctly in order to achieve the desired result. over, in the operating instructions, only a few manufacturers provide an answer to this sore question. Explore the article and find out how the line winds around the trimmer reel.

The procedure for winding the line on the trimmer spool

First of all, you should know that trimmers have different working attachments. The reel can be designed for different lengths and thicknesses of the line. this point should be taken into account when purchasing consumables.

So how does the line load into the trimmer reel? All work is divided into several stages:

First you need to disassemble the trimmer head.
Unscrew the nozzle by rotating the drum to the right.
Press with your fingers on the two latches located on different sides of the tap holes and remove the top cover of the nozzle. You can pry off the cover with a screwdriver. This should be done carefully: reels with automatic line feed have a spring that can forcefully throw the cover along with all the contents of the reel.
Remove old line scraps.
Now you need to find the middle of the line. To do this, unwind it to the required length (for example, 10 m), cut and fold in half.
Hook the middle of the line into the existing groove or insert it into the hole specially designed for this. And start winding. The direction is indicated by the arrow, which is usually marked on the trimmer reel body (usually against the rotation of the drum). Some models have a double-sided reel: in this case, the line should be wound in different directions: one end in one direction, the other in the other, while the loop of the line must be inserted into the dividing slot in the middle.
Leave loose ends of the line about 20cm each. Later they will need to be fixed in the recess.
And finally, the last step will be the assembly of the drum. Reinstall the washers and spring. On the top ring of the reel there are two notches where you need to tuck the antennae of the fishing line. Thread them through the holes and place the spool in the drum, trying to tighten the line without displacing the spring.
Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, excess line will be cut off by the trimmer blade.

As you can see, winding the line on the trimmer reel is not difficult: the main thing is to do everything right. And here are some more tips that will come in handy when choosing a fishing line, winding it and subsequent work:

The line comes in a variety of thicknesses and cross-sections. The best option for winding is the “native” line for this model;
Never use fishing line or metal cables for the trimmer. This replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure Not only the lawnmower himself, but also those around him;
The line is cut when the trimmer is in contact with hard objects. Try not to allow this, otherwise you will have to stop each time, turn off the device and rewind the line on the reel;
Use regular line for cutting lawn grass and braid line for coarse weeds. It is more durable and will not constantly cut.

than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

How to properly wind the line on the trimmer spool

So, in order to wind the line, you first need to remove the coil from the trimmer. this will be more convenient. The removal method will depend on the type of trimmer.

Removing the coil from the trimmer

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a hole on the inside of the reel for the fixing line, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. I wound the fishing line, we leave a small piece of it unwound to put it out. We fix this piece in a specially groove located on the inner part of the reel and designed so that at the time of collecting the reel, the line does NOT unwind. If there is such a groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and threading the outer piece of fishing line into the existing hole, collect and put the coil back on the trimmer.

If the coil is designed to work with two tendrils, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. Reels with one groove should have a through hole through which the fishing line is threaded. We rewind 2-4 m of fishing line, threading it through this hole so that the fishing line sticks out equally on each side. And we simultaneously wind both tendrils of the fishing line in one direction, opposite to the direction of rotation of the coil to the trim tabs and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, the resulting ends We fix in the Special grooves, and if they are not there, we hold them with our fingers. Threading both ends into the existing holes on the outer casing of the coil. We collect the coil and fasten it to the trimmers.

That’s all on this issue. Happy winding!

Things to consider when choosing a line

It is important to choose the right material before inserting and locking the line into the detachable trimmer spool.

Rating of the best petrol trimmer models. An overview of manufacturers and models, as well as useful tips from experts, considered in this review, will help in a difficult choice among many device models.

What are the trimmers and features of their use

The trimmer is useful for mowing small or difficult areas, such as near hedges, between beds and along paths. Today manufacturers produce a wide variety of gasoline, electric and battery models, which can be selected for any owner’s request.

A fishing line is used as a cutting element of the trimmer. In the process of work, sooner or later, its length will end, and then the owner will have a question of how to correctly replace and fix the thread tucked into a removable coil.

Auto feed trimmer: how to wind the line into the removable spool

Some models of trimmers have a reel, the threading of which is automatic. It is enough for the owner to fix the ends in the head, after turning on the equipment, the mechanism will perform all the winding manipulations on its own.

How to wind the line correctly on the spool of the trimmer with one tendril

Most often, a thread up to five meters long is used. The procedure consists of the following steps:

Bent the cord with a loop and insert into the groove of the head.
Wind the thread in the direction opposite to the marks on the body. They indicate the direction of movement of the head.
Leave the end of the thread up to fifteen centimeters long to increase the centrifugal force.
Thread the free end through the spool outlet.
Assemble the trimmer head.

How to properly wind the line around the trimmer: Step-by-step guide and instructions

A beautiful lawn will only look truly well-groomed if you regularly mow the grass. A trimmer is best for tackling difficult areas. Any owner of the unit will sooner or later face a solution to the problem of how to wind the line on a reel, because wrong actions can not only worsen the quality of the mowing, but also disable the equipment. Today in the Homius review we will tell you about all the methods and nuances of replacing the fishing line and the features of choosing consumables.

How to wind the line correctly: replacement features depending on the type of removable trimmer coil

To figure out how to tuck the line into the removable trimmer head, the following recommendations and instructions will help.

By size

Before threading the thread onto the trimmer spool, pay attention to its size. Most often used fishing line with a cross section of 2 mm.

You can choose a suitable diameter in the following ways:

See recommendations in the manufacturer’s instructions for trimmers.
Manufacturers often apply cross-sectional information to the bobbin.
The cross-section of the cord must match the diameter of the reel hole.

By quality

Before you put the line on the trimmer, you need to Pay attention to the section of the cord:

Whining with a circular cross-section is the most common option. They cut the grass perfectly even in difficult areas;
Spiral line is suitable for thin grass. It is not very durable and is NOT suitable for old thickets;
A cord with notches and sharp edges is chosen for mowing weeds;
A fishing line with a variety of geometric sections will help mow the lawn more evenly, but the strength of the consumables is low.

The owner of the lawn mower should know that it is absolutely forbidden to use metal wire, fishing thread and various strings.

How to wind the line on the detachable reel trimmer with two tendrils

You can see before work. And also take into account the following recommendations.

If there is only one track, both threads are wound parallel.
If there are two tracks, each piece is wound in a separate groove.
Wind the threads in the opposite direction to the rotation of the head.
The length of the risers does not have to exceed fifteen centimeters.
Thread the ends into the outlet holes.
Assemble the head and check the trimmer performance.

How to wind the line into the trimmer?

When threading the line for the first time, this process may seem quite laborious, but with time and skill, the task is solved much faster.

In order to fill the line, you must:

Take the coil, Unscrew its cover. Some spools are threaded to the left, so the cover must be unscrewed in the required direction.
Measure five meters of line;
Fold this segment in half, that is, determine where the middle is;
Next, place this middle of the line in a special hole on the reel;
Wind the line in the direction of the arrow;
If there are two places for winding, then the first part of the line should be wound on one half of the reel, and the second part on the other half;
Both ends of the line are pushed into the reel holes;
Screw the lid.

Correct winding of the line to the trimmer spool. How to remove the spool from the trimmer?

To change or wind the cutting thread on the spool, it must be removed.

The complexity of its removal depends on the tool model:

Low motor tool. The motor is almost in the ground here. To remove the coil you need to press the buttons located on the side of the trimmer. After pressing THESE buttons, the body opens, where the line spool is located.
Curved bar trimmer. Here it is necessary to return a special lamb counterclockwise. Then the coil and the spring in it are removed.
Straight bar tool. The bar is held still with a screwdriver or a second object. It is removed by turning it clockwise. After that, the tool is disassembled into parts and the bobbins are removed.

Line threading:

If a tool with one tendril is used, then about four meters of thread will be needed. This thread is passed into a hole inside the spool where it can be fixed. Next, one end of the line is directed in the direction of the arrow. Then the end of this thread is fixed in the groove, which is in the bobbin. This is necessary so that the thread could not unwind when assembling the spool. If there are no grooves, hold the line with your hand and collect the bobbins.
If a tool with two tendrils is used, then first check the number of grooves available.

If the reel is equipped with a semi-automatic mechanism, then the line is wound as follows:

The thread is threaded through the hole that is inside;
Secure the ends of the thread in the grooves on the body.
The coil is assembled and a special button is pressed;
After which the line itself begins to dangle in the right direction.

It must always be remembered that the cutting thread must be protected from hard things. This will extend its lifespan.

If you do not adhere to this rule, you will often have to stop work, remove the spool and change the thread to a new one.

What line is used for the trimmer?

There are several types of fishing line:

The most durable is rounded;
For Mowing soft vegetation. curly;
For mowing thin grass. from a notch;
Special. suitable for certain types of trimmer.

The section of the cutting thread must correspond to the vegetation to be cut.

If it is necessary to replace the fishing line, then it is necessary to select exactly the type recommended by the manufacturer of this particular trimmer model, that is, the thickness of the cutting thread should be suitable for the engine power and the size of the unit.

It is better to choose a specialized cutting thread. It is worth soaking the line for a while if you plan to replace it in the reel.

After soaking, it gains elasticity and becomes stronger.

The cutting thread can be made from different components. The most common among them is nylon.

This material is characterized by a high degree of wear resistance, the ability to withstand various temperatures and high loads.

Nylon line can be stored for a long time, It will not dry out or lose its strength.

Therefore, its service life can be quite long.

Lawnmower spools or heads have different structure:

One-string. There is only one working line in the modification of such a trimmer. This unit is used mainly for small jobs, such as trimming grass.
Two-stringed. They can be both automatic and semi-automatic. The package here includes two strings. This trimmer is used for mowing and clearing areas.

Instructions for correctly winding the cutting thread onto the trimmer spool:

First of all, you need to disassemble the head. To do this, press the latch and return the cover to the side. Next, the spool is removed.
Measure out the required amount of cutting thread and insert it into the slot.
Wind the line on both sides in the direction of the arrow.
Leave 15 cm ends NOT coiled.
These ends are inserted into opposite slots.
Then the ends are fixed in the hole on the head.
After that, the spool is carefully inserted into the body, for this you need to slightly press on it.
If necessary, you can pull the remaining ends of the thread outward. To do this, you first need to pull one end of the thread, and then the other so that they can easily pass through the slot on the head.
Now you should collect the grooves on the body and screw the cover.
Then press the spool and try to twist it all the way. If you hear a click, then the spool has clicked.
Next, you need to pull the free ends of the thread to the end.

Threading the spools with thread of different types of bobbins

With two-string automatic heads:

First you need to press the clip to the click, remove the cover.
Carefully return the bobbins so that it can detach from the holder. Extract her.
Measure two lengths of cutting thread of the same length. To make further work easier, the ends of the line must be cut off at an angle. Take one end and push it into a special hole in the coil. It can also be slots, grooves, clamps, etc.
Further in the direction of the arrow, you need to wind the fishing line, and quite tightly and evenly. In a special eyelet on the reel, you need to fix the end of the fishing line.
Subject the other half of the line to the same operation, only on the other half of the reel.
The next step is to install the coil in the trimmer head. And thread the rest of the line through the hole in the head.
Then carefully straighten the thread and close the lid. If the line turns out to be long, then it is better to cut off the excess. About fifteen centimeters should remain on each side.

On the semi-automatic head:

The thread is threaded through the hole that is inside;
Secure the ends of the thread in the grooves on the body.
The coil is assembled and a special button is pressed;
After which the line itself begins to dangle in the right direction.

It is necessary to very carefully and carefully thread the cutting thread into the unit, because not only the cleanliness of the garden area, but also personal safety depends on the correct winding of it.

Sources:

http://cylinder.com.ua/blog/kak_namotat_lesku_na_katushku_trimmera
http://instrument-tehnika.ru/kak-pravilno-namotaty-lesku-na-katushku-trimmera/
http://womanadvice.ru/kak-pravilno-namotat-lesku-na-katushku-trimmera
http://instrument-tehnika.ru/kak-pravilno-namotaty-lesku-na-katushku-trimmera/
http://homius.ru/kak-namotat-lesku-na-trimmer.html
http://superkaras.ru/sposoby/spinning/kak-namotat-lesku-na-katushku-trimmera.html

Grass Trimmer line, reel, trimmer, wind