Install a line for a trimmer for a trimmer for Makita grass. Coil with one working osik

How to change a fishing line for a trimmer in a trimmer Makita

The owners of the trimmers, mainly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or fishing line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.by.step instructions given later.

  • Before refueling the fishing line for the trimmer to the coil, drown out the engine of motorcycles or de.energize the ethletric trimmer for the grass to avoid injuries that may occur in case of accidental rotation of the cutting tool.
  • Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
  • Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, to twist the coil of the trimmer for the grass should be right, that is, clockwise.
  • Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
  • Cut the required amount of fishing line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the fishing line, since this will lead to increased load on the engine and greater consumption of gasoline.
  • Find the middle of the segment of the cord, folding it in half. You will get a loop.
  • Special grooves are cut out inside the coil (there may be holes). Insert the loop from the fishing line into this groove.
  • Wind a fishing line for a trimmer to a coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the fishing line about 20 cm long and fix them in the grooves located on the sides of the coil.
  • Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
  • Dress the lid and fix it with latches.
  • Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Tighten the coil of the trimmer for the grass will need to go to the left (against h. Arrows).

Varieties of fishing line in shape. what it affects and why they are different

Initially, the fishing line for the trimmer was produced only a round shape, but other modifications soon began to appear. square, hexagonal, in the form of a star and others. They are still different in color, but the color does not affect anything, except for the visibility of cutting equipment during operation.

The shape of the string affects the type of mowing grass. In the shape of the cord there are:

  • Round is a common form that is still considered universal. The round shape of the string is divided into smooth and with turns. If a smooth string is characterized by noisiness of work, then twisted on the contrary works quieter, but its accelerated consumption is observed
  • Square and hexagonal. the presence of sharp corners provides a more effective cut of vegetation, which must be taken into account when processing large areas
  • Ribbed and in the form of a star. even more effectively cut different types of stems, and reduce the load on the engine

Some craftsmen, when spent on the fishing line, replace it with a steel wire or metal string, which is unacceptable. The wire is not only capable of cutting the dense shoes of the roeer, but can also be wound on the head, which will lead to its jamming with the shaft. The jammed head will entail the wear of the gear ratio and the power unit.

The shape of the section Appointment Advantages Flaws
Round For young and green grass only Cheapness, resistance to large loads, smooth cut and low consumption Noisiness during work, and is not suitable for dry and thick.nisted grass
Quadrratic High green and dried grass Even cut of grass, lack of crushing stems Large consumption, quick wear, fragility and the possibility of use only on powerful trimmers
Star Dry grass and shrubs High.quality and effective cut due to a large number of corner faces High cost, the possibility of using on the corresponding heads
Twisted round Any grass from green young to dried Effective cut of stems, high speed and performance, noiselessness Quickly wear out, hardly unwinds from the coil during operation

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

On some models of lawn mowers, the trimmer head for grass is first provided for, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. head assembly with a coil; 2. extracting neatly with a small axial turn; 3. extracted details

The old fishing line for the trimmer is completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

install, line, trimmer, makita, grass, coil

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Replacing the fishing line for grass: step.by.step instructions for replacing fishing line on a trimmer

Trammers for grass (they are also law mmores) are actively used by modern society to care for lawns and other similar objects of horticultural farms. The tool is marked by high efficiency, despite the dubious quality of hacking of grass (compared to the usual peasant scythe. the earth and the sky). The main advantage of trimmers (lawn mowers) is high productivity with the low cost of the physical forces of the operator. However, over time, the cutting element of a trimmer for grass (nylon forest) wear or damage, which as a result makes a trimmer for the grass with a useless tool. Hence the task becomes relevant how to replace the trimmer head and how to replace the fishing line for the trimmer of the head of the trimmer for grass? Consider this process on the example of the Black and Decker lawnies and others.

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

install, line, trimmer, makita, grass, coil

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

See what I like about the Makita DUR368 Line trimmer on the Turf and Tools Channel.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. head assembly with a coil; 2. extracting neatly with a small axial turn; 3. extracted details

The old fishing line for the trimmer is completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

trimmer for grass. make the best choice. Part 3 (trimmer fishing line for trimmer, trimmer head, knife for a trimmer for grass)

For a comfortable haircut of vegetation in the personal plot of the optimal choice of trimmer characteristics for the grass, it will not be enough. And for an electric trimmer for grass and for gasoline motorcycles, you must choose the right cutting tool. As such, a trimmer fishing line for a trimmer (cord) or a special knife is used as such.

Fundamental when choosing what to mow is the type of vegetation. For the convenience of work, the user can choose the type of cord, type of trimmer head, the method of refueling the cord into it, choose a knife of a certain form. Therefore, you should familiarize yourself with these characteristics in detail.

Trimmer for grass

When spinning with a trimmer cord of high grass, it will be wrapped in a spindle at the place of mounting a spit.head. How often this will happen, largely depends on the design of the head and the properties of mowing grass, but it is practically not possible to completely avoid this. The optimal output will be a mowing not a cord, but a trimmer knife specially designed for such cases.

A knife used as a cutting tool for a trimmer for grass can be made of plastic or metal and have a different amount of blades (teeth) in a variety of shapes.

Only plastic knives should be used on trimmers with a curved bar with a curved bar (for the safety of the mower and commensurate with the capabilities of the flexible shaft). In addition, they often come with electric trimmers.

This can be either a special mowing head with replaceable removable plastic knives, as well as a whole design in the form of a disk knife with a different number of blades. Such trimmer knives are hard vegetation on the teeth (dry grass, burdocks, nettles, etc.D.).

For processing large territories and mowing not only grass, but also cutting a shrub or even young trees, metal knives are used. The only thing that such trimmer knives are “afraid” are clashes with objects too hard for them (for example, stones).

Metal knives can only be used on trimmers with a direct bar. On a tool with a curved bar, they cannot be installed. This is primarily due to safety precautions. If when spinning vegetation, the disk stumbles upon a solid obstacle, then in this case it throws it back. Trimmers with a direct rod distance to the user’s legs are significant further.

Plus to keep the tool helps t (u) or J-shaped handle, and a special protruding restrictive bar is added to the d (o)-shaped handle, which resting in the leg does not allow the cutting tool to let it into it. Trammers for grass with a curved bar are usually equipped with a D (O)-shaped handle without a limiter.

Secondly, having a high torque, a metal disk knife creates a large load on a flexible shaft and engine, which leads to a quick breakdown of the tool.

As user experience shows, the shape of the blades (triangular, rectangular, etc.D.) practically does not affect the quality and speed of the mowing. But their number becomes important when using a trimmer for grass for hay harvesting. Three or four.lobed knives when spent too chopped grass.

The most optimal for hayfields are almost round eight.toe knives or with four large and additional smaller teeth between them. Perilation discs with a large number of teeth are also popular. such a lightweight mill for a trimmer for grass can be installed on low.power tools.

Using a cutter for a trimmer for grass, that is, a disk knife with a large number of teeth, you can not only without problems clear the site from a luxurious perennial weeds, raspberries, etc. P., but also cut trees with a trunk diameter of several centimeters.

Types of trimmer heads for coils

The main parts of the trigger is a mowing spike, which is a cylindrical case with a snut.inserted coil (bobbin). A fishing line for a trimmer (cord) is refueling into it. The heads differ from each other in terms of supply and dressing of the cord. There are three types of heads in total:

  • Automatic. The supply of the fishing line is carried out after which, as the user reduces the speed of the motor. Automatic supply of the cord is very comfortable when it is necessary to perform a large amount of work. The minus of such a head consists in a large expenditure of the thread.
  • Automatic. The use of such a head does not ask the user to do some complex manipulations. The principle of its operation is arranged so that the fishing line for a trimmer begins to automatically lengthen at a time when a trimmer for the grass works at full speed. It is only necessary to hit the apparatus with the head of the apparatus a little (this will remove the locking of the fishing line), and the cord will move out of the keyboard due to the centrifugal force. Then the fishing line for the trimmer is cut to the desired length with a knife, which is placed on a protective casing.
  • Manual. To lengthen the cord, you need to suspend the device. After that, the fishing line for the trimmer will need to be pulled manually.

How to replace string trimmer edger line

How to change a fishing line for a trimmer in a trimmer for grass

How to change the marshmallows of which is better to choose

Since the choice of a trimmer for the grass we saw in the previous article, now we will tell how to correctly refuel a trimmer for the grass with a fishing line, and which is better to choose based on the criterion of work.

After you purchased a trimmer for the grass and began to use it intensively, at some point the question will arise about the substitution of the fishing line, since this is the most weary element in the tool, the rich operation of the trimmer for the grass will often lead to replacement of consumables.

You will need it

Bobbins of the trimmers, the motor of which is located near the ground, have a different fastening to the rotation axis, they have two buttons on the coil located on the sides that need to be squeezed, the rest of the thread is no different from the other cassettes.

The principle of proper winding of the fishing line is similar in all of the listed services, so for example, consider the standard option with two antennae.

To remove the coil with a fishing line, you must unscrew the screw in the center, but keep in mind, the thread there is left, so you will have to twist clockwise, it is specially so that it does not open under the influence of centrifugal force during operation.

Next, using the screwdriver, disassemble the head and remove the coil, on which the fishing line for the trimmer is directly wound. I had to take a trimmer for the grass. It is enough to process grass in the garden and how it is. Having measured the required length and folding it in half, you need to refuel the coil, withdrawing, as a result, its ends opposite each other (for this there are special slots for fixation).

After that, it is necessary to assemble the head in the reverse order, passing the ends of the cord in two corresponding holes.

If there are doubts or it is not entirely clear how to charge a trimmer for the grass, we recommend that you see how to correct the fishing line for a trimmer into a lawn mower. How to rent a coil C is the only sure solution for mowing grass in a fishing line for a trimmer in. In this video, the instructor will open a trimmer head in detail by steps, it will measure the required amount of fishing line, as a rule, this is from two to four meters, and demonstrate the assembly and installation for a trimmer for the grass.

How to replace a fishing line for a trimmer in a trimmer

The winding direction is indicated on the coil with an arrow.Then we spread the mustache through the holes in the top cover. We dress it on the base and snap it. All. It is worth trying once and next time you will do everything with almost closed eyes.

Put a bobbin on a trimmer for the grass and proceed to mow.If the edges of the fishing line are bred too long, you can bite them off with nippers to the desired length.

Instructions with a step.by.step description how to wind the coil of a trimmer for grass and lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting!The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

The choice of fishing line

In order for the dressing of the fishing line to the trimmer head to be successful, it is important not to fail to choose the consumer material. The thicker the cord you refuel, the more thick and hard grass it can cut

A universal fishing line for a trimmer is often used, the diameter of which is 2 mm. You can choose the diameter suitable for the mower in the following ways:

See the information about the thickness of the fishing line in the instructions attached to the trimmer. Pay attention to the squash itself. Sometimes information is applied on it about possible fishing line diameters. Another option is to try to insert the cord into the output

If it easily passes into it, then the selected fishing diameter is suitable for use.

You can choose a cord thread by type of engine. If the fishing line for the trimmer is too thick, then the resistance to rotation will increase. the engine in this case will overheat and will soon fail. Useful recommendations:

  • For an electric device with an engine of less than 500 in, a thread of 1.3 mm thick is suitable. If this was not found, then you can use a fishing line for a trimmer by 1.6 mm. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
  • The gasoline trimmer for grass has a shaft mower. For the bent version, the cord for 2 mm is often used. If the shaft is straight, then set the thread 2.4–2.5 or 3 mm. The thickest fishing line for a trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cross section of the cordry thread. Some popular options:

  • The most common fishing lines with a round section. They mow fresh herbs well, but they cope worse with shrubs, drows.
  • Twisted (spiral) cord does not differ in high strength, but well suitable for thin young grass.
  • The jagged thread with sharp edges is ideal for a large weeds in a neglected area.
  • You can mow the lawn in a rectangular, starry or square fishing line for a trimmer for grass, but they are not very durable.
  • The most durable is a two.component cord with an internal core and a round section.

Keep in mind that it is impossible to use wire, metal strings and cables, as well as an ordinary fishing thread. The device will be dangerous for both the user and for others. So the cable or similar products will gradually begin to shut down, as a result, their ends will be reacted, and small pieces will scatter at high speed.

A review on a trimmer for grass Electric Makita UR3501

Despite the fact that we remove the grass on the site using lawnmands, a trimmer for the grass is needed in any case, since the lawn mower will not be able to climb into narrow places or remove the grass near the garden path or mow the grass in the thicket of bushes. Like it or not, and a trimmer for grass on a suburban area in any case.

Why did the choice fall precisely on Makita, because I like the goods of this company, I have a wide variety of them and have been using them for many years now. Perhaps there are trimmers for grass and much better from other manufacturers, but I like Makita.

A trimmer for grass is supplied in a conventional cardboard box decorated in the style of Makita products. The packaging is not noteworthy, the cardboard is not very dense, but it fully copes with its direct responsibilities to protect the transported product. The trimmer itself for the grass in the package, in fact, is not fixed by anything (maintained only by boxes with accessories), therefore, it dangles when carrying. It is unlikely that of course this will affect his performance, but still could put several foam inserts in the package that would fix it. I do not think that the use of such inserts would greatly affect the final price of a trimmer for grass.

In addition to a trimmer for grass in the package, there is another box in which you will find a protective cover, a handle, a shoulder belt, fasteners and a screwdriver combined with a hexagonal key. That is, there is everything in the kit to quickly assemble a trimmer for grass.

The assembly is simple, there is not even the need to look into the diagram, everything is clear intuitively, where what part is attached.

Instructions in Russian and quite detailed, all manipulations with a trimmer are described (assembly, operation, maintenance).

There are no complaints about the assembly quality. The trimmer for the grass is made of high.quality and thick plastic, so there is a very great hope for its long.term use. The trimmer for grass does not publish extraneous unpleasant chemical odors, which once again confirms the quality of the materials from which it is made.

In general, the Makita technique has always highlighted the quality of the products produced.

Trimmer for electric grass, eats from the network 220 volts. It was originally planned to buy a battery trimmer for grass, but they are inferior in power, so it was decided to buy a network.

The width of the mowing is 35 centimeters and in my opinion this is more than enough, after all, it is not a lawn mower.

Trammer for the grass is not small and this was another of the criteria for buying for my high growth. In operation, the trimmer for the grass is very convenient, otherwise with the old one always had to bend a little. On the other hand, large dimensions may be uncomfortable for people of short. Here everyone already chooses a trimmer for grass under their height.

The weight of 4.3 kg declared by the manufacturer. It is felt enough in your hands and you just can’t work without a shoulder belt for a long time, your hands will get tired quickly. It’s good that the manufacturer has already put the shoulder belt in the kit. Speaking of a belt. It is the most common, made of a synthetic thread and I can say that not very convenient. If you work with a trimmer in one T.shirt, then the belt quickly begins to rub your shoulder, and if you work without a T.shirt, then you run the risk of tearing your skin on your shoulder. In any case, the belt requires refinement in the form of all kinds of soft inserts or replacement with another.

The capacity declared by the manufacturer is 1000 watts. I don’t know exactly how this power is calculated and what it means, but I can say that the power of a trimmer for the grass is enough to mow thick grass. He does not stall and does not stop when you mowing tall and thick grass and it’s just wonderful, just what you need when you mow the grass behind the fence of the site, and there it is always thick.

It’s a pity that there is no automatic fishing line in the trimmer. This function is mechanical, performed by a light blow of the cutting head on the ground. In principle, such a solution does not create any big inconvenience. On the other hand, the automatic supply of fishing line as a whole increases the final cost of the product, so here the choice is already for the buyer, which is more convenient for him and whether he is ready to overpay several thousand. I generally get tired of the mechanical supply of fishing line.

By the way, the cutting head itself during operation is not very hot even with prolonged operation of a trimmer for grass.

How to remove a coil from a trimmer for the grass Makita UR3501

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Automatic winding of the fishing line on the reel

There is a variety of coils in which the automatic mechanism performs winding on its own. it is enough to correctly season the fishing line for a trimmer from the user. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are spread through the hole on the outer body, the bobbin is assembled, and when rotating the winding button for the trimmer, it is wound independently inside. It is impossible to make the winding incorrectly in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Method 2. two segments

The only difference from the method is no different from the method. two wound segments of fishing line, instead of one.

There are two special fixing nests on the coil (see drawing above).

They hook it previously formed on the fishing line, and begin to wrap a fishing line for a trimmer.

Winding is carried out in a special order

The winding needs to be carried out in the following order: first the lower fishing line for the trimmer, t.e. that which is closer to the fixing holes at the bottom of the coil, and only then the upper one, t.e. the one that will overlap the lower section.

The tips are made in the holes of the corps of the rogue trimmer for the grass. They are pulled to a click, which means that the fishing line for the trimmer has left the latch.

The tips are torn into the holes of the corps of the rogue trimmer for the grass

The coil is fastened into the case. The fishing line for the trimmer in the rogue is replaced.

Boarding line refueling instructions. 150 cm?

In order for the trimmer for the grass to work “like a clock”, you need to choose the right fishing line for a trimmer, that is, choose it taking into account the trimmer model for grass and the type of work. Two important parameters in this matter. This is diameter and section.

The diameter of the fishing line must correspond to the recommended for this model (in the passport for the product it is necessarily indicated). The cross section of the fishing line is round, square, with sharp faces (pentarannik). The fishing line for a trimmer with a round section is designed for a bevel of young grass and a lawn, a square and five.grade fishing line for a trimmer will come in handy if the grass was booing and weeds have grown on the lawns.

The mowing heads of the trimmer for the grass can be of various modifications: one.built for trimming the lawn (mows using one thread of fishing line); Two.string to mow grass and clearing the territories with automatic supply of fishing line or manual adjustment of the length of the string.

How to put a chain instead of a fishing line on a trimmer for grass

You can additionally “pump” the unit to mow not only grass, but also weeds and young growth. This does not require expensive tools or special skills. As they say, everything is brilliant just!

  • chain from the old chainsaw;
  • A cup bent inside, which is used to attach a trimmer for grass;
  • washer and nut;
  • vise, marker and ruler;
  • welding machine;
  • drill;
  • Metal for metal.

The length from the ends of the chain to the puck should be the same.

Removing and disassembling the coil

The braid trimmer head consists of a casing, a spring (not in every model), bobbins with a cord, cover. Before proceeding to disassemble the coil of the electronic unit, certainly turn off the trimmer for the grass from the network. The disassembly method is located depending on the mounting of the mowing head. 1st option:

  • To remove the lid covering the inside of the head, click on the latches (latches), which are placed from 2 of its sides.
  • Remove the lid under which you will see the spool. remove it from the body. Some trimmers under the bobbin have a spring, which should also be carefully removed.
  • Removing the bobbin, you will see the screw in the center of the case. Unscrew it with a screwdriver.
  • After extracting the fasteners, take the case body and, shaking it in different directions, remove the gearbox from the shaft.

In the 2nd version, the head of the trimmer for grass is twisted onto the shaft of the gearbox. To remove it, you need to fix the shaft. To do this, in such devices, a hole is foreseen, through which a narrow screwdriver or an iron bar is inserted. Short annotation:

  • Shoot a screwdriver in a special hole, then stall the shaft.
  • Get the body of the head and start twist it. This should be done clockwise, t. to. Larva shaft thread.

How to choose a fishing line for a trimmer for a trimmer for grass and replace it?

This question only at first glance seems simple, and when you pick up the tool, you just don’t know where to start.

So, consider what types of forests are generally. There are 4 main configurations: round, curly, with notch, as well as professional. A round fishing line for a trimmer is used to cut hard plants, as it is considered the most durable. Figure is best suited for working with soft grass, and the one with notch with thin. Professional usually does not fit a simple everyday tool, which must be taken into account. If you have chosen a trimmer for Makita grass, then the guide to it may be given information on the fishing tables used.

Now, with regard to the replacement of fishing line. This procedure is performed step by step and may vary depending on the model of the trimmer for the grass.

First stage. we analyze the instrument head. There is usually a special latch on his case, which needs to be pressed, after which it will be possible to freely unscrew the lid.

The second stage. remove the lid, pull out the bobbin and find the hole on it. It is necessary to insert the end of the fishing line into it, having previously measured 6-7 meters.

The third stage. we wound a fishing line for a trimmer on both sides as painted with arrows on a bastard. The optimal length of the remaining free ends is 15-20 centimeters. Distance from the edge of the rogue to the fishing line. 6 mm.

The fourth stage. insert the free ends into other holes on the bobbin and fix it in the grooves of the head. Nothing should hang out, this is a very important point. After that, you will need to insert the spring into the bobbin.

Fifth stage. we put the lid on the head and check if all its elements entered the grooves. The bobbin can be scrolled counterclockwise to click. This is an indication that she sat tight in the head.

Of course, we described the process of replacing the fishing line in the trimmer superficially and best to carefully study the operating manual, since each tool has its own individual characteristics that must be taken into account.

In the Makita-Profi online store you can find many useful tools, for example, a powerful Makita electric steamer, Makita electric screwdriver, a drill, a corner grinder, metal scissors and much more. Acceptable prices, high quality of goods. We are the official dealer of the concern Makita.

trimmer for makita grass replacement

In this leadership, we will analyze the entire replacement process step by step. Moving forward, there are two ways to align the coil of the trimmer for the grass from the fishing line. There is no fundamental difference. The difference is that in the first case one line will be folded in half, and in the second. Two lines of such lines.

Preparation for replacement

For clarity, the mower (coil) was removed from the bush. To replace the fishing line for the trimmer, it does not need to be removed, everything is done in place. It does not take a lot of time.

Disassemble the coil of the trimmer for the grass. She rests on latches. Remove the lid by clicking on the latches. If you do not have enough effort with your hands, then use a screwdriver.

The coil consists of the following:

The principle of operation is as follows. When you press the button, the coil presses on the spring and comes out of the fixing grooves in the casing of the coil. Holding the coil in this state, you can twist, thereby adjusting the length of the mowing fishing line. When you release the button, the spring spring returns the coil to the original fixed state.

There are several holes in the lower part of the coil for different diameters of the mowing fishing line. Different manufacturers of trimmers may differ. In some cases (as here) they are signed in others. Not.

These holes are necessary to fix the spit line when replacing it. After winding on the woman’s rod, the ends of the latter are inserted into them. This is necessary so that the frame does not spin when installing the coil in the trimmer housing for grass. In other words, this facilitates the replacement of a mowing fishing line.

There are models without specifying the diameter of consumables. Then, to find out what maximum forest diameter can be used, it is tried through the holes to remove the mowing fishing line from the trimmer coil body for grass (see. Figure below).

The coil has two sections for the fishing line separated by a partition. They may not be. They are needed only to distinguish and facilitate the winding of consumables.

At first the necessary length of the forest was determined. The latter is wound on one of the coil sections so that it does not go beyond it. At the same time, 3 mm was wound, length. About 2 meters. Those. For two sections you will need a 4-meter section. This is for the 1st method. The second method requires two segments of 2 meters.

Now you need to find out how you need to wind. To do this, many manufacturers of trimmers on coils use special characters, for example, in the figure below.

If such markings were not found, you need to pay attention to the coil body. Soon an arrow appears indicating the movement of the mowing. Lines for a trimmer wrapped in the opposite direction.

The first way

Bend the prepared segment (in this case 4 meters) approximately in half. One segment should be 15-20 cm longer and inserted into a special slot located on the partition.

The fishing line for the trimmer is wound in a predetermined direction. This is done in a dense landing, the fishing line for the trimmer is neatly distributed. In this case, you need to turn the segment, which is longer, in the part that is closer to the button.

There are structures in which the separation of the coil into two sections is not provided for. This does not change anything, the fishing line for the trimmer is wound in the same way. You just need to make sure that the segments do not intersect with each other.

The first should be the segment that is located at the bottom of the coil, that is, the one that is closer to the mounting holes.

This tip is placed in the hole of the corresponding diameter. The scaffold is firmly fixed.

Long cut is wound for another six months. There this is similarly fixed. In this case, the segment crosses another part of the coil.

A long cut is wound for another half turnover

The fixed ends of the wound mowing fishing line are inserted into the holes of the trimmer coil body for grass.

The fixed ends of the wound mowing fishing line are inserted into the holes of the trimmer coil body for grass

The coil is attached to the body. The ends of the braid fishing line are stretched with force, so that the fishing line for the trimmer, previously fixed in the holes of the coil, comes out. This is easy to determine by a characteristic sound (click).

The coil with the button is fixed in the trimmer coil body for grass.

Insert the coil with the button in the trimmer coil body for the grass

The replacement of the mowing fishing line was successful. In this case, you need to install it back on a trimmer for grass, and you can start mowing the grass.

This should be repeated, you do not need to remove the coil from the trimmer for the grass. This was done to facilitate the process of replacing the fishing line. You can disassemble the coil in place, wind it on the coil and put it back.

Tips can and should be cut so that they do not fall on the trimmer cover for the grass.

Two segments

The method is fundamentally not different from the method the only difference. Two lengths of wound mowing fishing line, not one.

There are two special fixing nests on the coil (see. The drawing is higher).

They hook it, previously formed on a mowing fishing line, and begin to wind a fishing line for a trimmer.

Winding is carried out in a special order.

The winding should be performed in the following order: first the lower row, t.E. One that is closer to the mounting holes in the lower part of the coil, and only then the upper one, that is, the one that will close the lower part.

The tips are made in the holes in the body of the trimmer coil for the grass. They are pulled up to click, indicating that the fishing line for the trimmer left the clips.

The tips are lowered into the holes of the trimmer coil body for grass

The coil is attached to the body. A fishing rod in the coil was replaced.

How to wind a fishing line for a trimmer to a head of a trimmer for grass or a bush

Replacing a spit fishing line in a trimmer: 2 simple ways

The reviews of our readers are very important for us. Leave your assessment in the Комментарии и мнения владельцев with the argument of your choice. Your opinion will be useful to other users.

I want to devote today’s article to the painful topic of summer residents and gardeners of the entire post.Soviet space “How to fill the fishing line for the trimmer in the Trimmer”. Not many trimmers’ manufacturers answer this question in the operating instructions. Therefore, ordinary gardeners are difficult to understand how to do it right.

Instructions

In order to change the fishing line for the trimmer, it is necessary to extract the old one (if it was).

The coil is part of the design of the trimmer for the grass, which is located inside the head of the motorcosa, drum or bobbin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from a trimmer for grass and how to get a drum out of it.

Instructions on how to promote a hand head on a trimmer is described below.

  • First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
  • The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
  • The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
  • Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
  • Now it remains to extract an old fishing line for a trimmer and follow the following instructions.

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the fishing line, it is worth making sure that the thread suitable for a trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m fishing line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the fishing line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the fishing line for the trimmer sits in the coil exactly.

Do not forget that the thick thread will be shorter than thin.

The instructions for refueling the fishing line in the coil is described below.

  • The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
  • Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m.
  • Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot.
  • To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. there should be an arrow on it.
  • If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction.
  • Now you need to season the reel with a fishing line. It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage a trimmer for grass. At this stage, you need to charge the coil very carefully.
  • When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand).
  • Put the coil itself in the coil head, before that, extinguishing a fishing line for a trimmer through the holes inside the drum.
  • Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the fishing line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard).
  • Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer for the grass and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

Frequent errors

Although the winding of the fishing line is a very simple task, many newcomers can wrap a fishing line for a trimmer incorrectly. The most common errors are presented below.

  • Many people when measuring the thread think that 4 m is a lot. Because of this, people often measure less, and they, accordingly, do not have enough fishing line. Do not be afraid to measure a lot, because you can always cut off the excess.
  • In a hurry, some people do not observe the gas stations inside the coil and wind up the thread like it. This leads to the “departure” of the fishing line from the coil and can even cripple.
  • For winding, it is worth using only the corresponding fishing line for the trimmer. This error is most common. You need to monitor not only the thickness and volume of the fishing line, but also your type. You should not use the first fishing line for a trimmer for wrapping, which will not match the goals. For example, you do not need to use a thread on the young grass, if it is necessary to mow dry.
  • Do not turn on the device until complete winding and collection. Although this is obvious, some people do this in order to check if everything is done correctly.
  • In no case should you confuse the refueling direction, as it will overload the engine, and it will soon get out of the working condition.

Beginners are quite characteristic of mistakes, so it is necessary to observe the advice given in this article.