Installation of a spring on a trimmer for Hammer grass. Typical malfunctions of trimmers of the gasoline group

Spring for a trimmer

The second method differs from the first in that not a whole piece of equipment is charged into the coil, but segments of two parts. Manufacturers use this way, and it is also suitable for those who have the remains of the material. The principle of how to insert two segments of the fishing line into the tip of the motorcycles, the same with the first way, and to make sure of this, below is a detailed instruction:

• There are two equal lengths of the segment of the material that you can use
• One segment is taken, and the edge is bend in the form of a clamping bracket or hook, with which the fishing line will be fixed
• Inside the coil, there are holes in the form of a bracket for fixation, which are there for a reason. If they are not, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is on its own
• The line of fishing line should catch on the bracket, and make it wound in compliance with the direction of the arrow
• The equipment is wound until the segment of 10-15 cm remains, which is fixed in the corresponding hole on the side of the tip
• The same manipulations with the second end of the fishing line are carried out
• The protrusions are starting into the holes of the head, and then, extracting the equipment from temporary fasteners in the coil, a cover with clamps is installed

The above instructions on how to install a fishing line for a trimmer in a motorcycle will help not only correctly, but also quickly perform a replacement procedure. The assembly of the coil of the trimmer for the grass, as mentioned above, can be performed without removing the head, but in this case you will need to conveniently fix the tool. Video Instruction is presented below.

The device and principle of operation of the starter on the trimmer

The gasoline engine is, in principle, the main part of the motorcycles its power lies in the range of 0.5-2.5 liters.With. The movement from it is transmitted by the shaft located inside the hollow bar, and then through the gearbox, consisting of gears, already a fishing line or a knife (working body).

Also, the lawn mower has the following elements:

• protective casing;
• lever;
• a belt designed for ease of use of the device;
• Starter serving for launching a gasoline internal combustion engine.

All parts of the motorcycles are presented in the photo further.

The starter on the trimmer is an integral part, which performs the engine starting into operation. It is shown separately in two photos below.

The starter mechanisms of various models of the benzos work according to the same principle: during the launch of the ICE, the protrusions marked in the photograph above the number 1 are included in the hook with dogs 3. When the engine begins to work, they return to their previous position due to the effects of centrifugal. Similar role is also played by wires 2.

The process of returning to the initial position of the elements of the mechanism occurs due to the presence of a spring screwed around the axis. It unfolds when the rope is pulled. After releasing the cord, it is drawn and winding due to folding the spring. During the launch of the ICE of the lawn mower, the triggering mechanism turns its shaft until it starts to work (starts).

To date, gasoline motorcycles are equipped with two types of starter mechanisms:

The first option is much more common.

The starter on the trimmer can function without breakdowns for a long time. It is impossible to unambiguously indicate the deadline. Everything is determined by the initial quality of the device and compliance with the rules of handling it.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

• The coil is turned over, installing it so that the spring bend exactly stands into the groove of the case, as in the photo below;
• lay two washers between which a spring is placed;
• put in place a cup of antennae;
• Twist the screw (photos below).

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just unscrew the screw a little, and the starter knot will begin to work without shaken. But this option is temporary. it is better to repair qualitatively as quickly as possible.

The main malfunctions of the starter of the trimmer for grass

It is not difficult to determine the cause of the breakdown of the starting device. There are several main options:

These details are shown in the photo below.

It may happen that the starting mechanism will be accidentally broken. The consequences will turn out to be deplorable if the ragged rope is wound around the flywheel of a working internal combustion engine: then the spring bursts, the pulley will tear off. But such cases when a complete replacement of the starting node is required, they rarely occur. In most cases, to fix the mechanism, it is enough to put a new spring or replace the cord.

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

• spin a screw with a screwdriver, fixing the pulley with a starter lid;
• take out a spring and antennae;
• Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
• determine why the launch mechanism has broken;
• If the spring collapses almost completely, then it is replaced;
• When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst. Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges.

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

Spring tension

After installing the spring, it should be pulled. The following actions are performed for this:

• Remove the handle from the starter cord;
• Then the rope is inserted into the coil groove;
• They stretch the spring, rotating the coil in the direction opposite to the clock of the clock arrow (reviews);
• make the desired number of revolutions specified in the instructions for the use of the trimmer model used and the corresponding length of the cord used;
• At the very end, the rope is threaded into a hole designed for this, located in the starter cover;
• put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this in the following ways:

• Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
• drill holes on two sides of the groove in the coil, into which the spring hook is inserted and fix it using a wire.

Replacing a torn cord

A torn rope is replaced in the following sequence:

• The old cord is removed;
• choose a suitable rope (thickness and length);
• Having reached it through a special hole in the coil, a knot is tied;
• Sprinkle a spring, producing the required number of revolutions;
• Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way. In this case, there are some nuances associated with their constructive features.

Spring mechanism

The manual structure is simple, but it can be improved to save time and time. For example, put an electric steel for a walk.behind tractor. Then you will not have to pull the handle every time. But keep in mind: this design is not suitable for all starters with manual launch. And the electric circuit that you choose for installation may not be suitable for every engine.

In these cases, it is worth paying attention to the third option: the spring mechanism of engine start. After installing it on the engine, just shift the motor block handle, and it will immediately start. This type of kickstarter is based on the semi.automatic work of the spring. It accelerates the engine installed on a one.axle tractor, without the need to pull the handle with your hands. To change completely manual starter to a mechanical, it may take about two hours of time.

The main malfunctions of the starter of the trimmer for grass

It is not difficult to determine the cause of the breakdown of the starting device. There are several main options:

These details are shown in the photo below.

It may happen that the starting mechanism will be accidentally broken. The consequences will turn out to be deplorable if the ragged rope is wound around the flywheel of a working internal combustion engine: then the spring bursts, the pulley will tear off. But such cases when a complete replacement of the starting node is required, they rarely occur. In most cases, to fix the mechanism, it is enough to put a new spring or replace the cord.

The main malfunctions of the starter of the trimmer for grass

It is not difficult to determine the cause of the breakdown of the starting device. There are several main options:

These details are shown in the photo below.

It may happen that the starting mechanism will be accidentally broken. The consequences will turn out to be deplorable if the ragged rope is wound around the flywheel of a working internal combustion engine: then the spring bursts, the pulley will tear off. But such cases when a complete replacement of the starting node is required, they rarely occur. In most cases, to fix the mechanism, it is enough to put a new spring or replace the cord.

The main breakdown of the starter of the lawn mower

Two main malfunctions of the starter of the gasoline trimmer for grass are currently spreading:

In practice, there are cases when for some reason there is damage to the starter case and a ragged cord is wound on the engine shaft, which certainly leads to a fragment of the spring and cracks on the case. In the current situation, the local repair of the starter of the lawn mower will be impossible and a complete replacement of the engine start.up unit will be required. In other cases, the elimination of malfunctions will be reduced to the replacement of the spring or cord.

Important! When winding and installing the spring, it should be remembered that it is hot, which means that it can burst if you make too much effort. The new part is inexpensive, but you will have to spend time on its search, which means that work on mowing the grass will move endlessly

To wind the spring, it is necessary to place the bend in the groove, and then, rotating the coil, carefully lay the part along the inner diameter of the coil. In this case, the spring should constantly hold on. If it is not fixed, the part slides and jumped out, then you must again wind. With proper execution, the spring fit tightly to its saddle.

Replacement of the cord

To replace the element in the coil, you need to find the hole through which the cord passes, and then tie the knot. Next, you will need to wind the coil for several revolutions.

The note! You can find out the exact number of revolutions by reading the instructions of the trimmer for grass or manually. To do this, measure the length of the rope and calculate how many times it can be wrapped around the coil.

For example, if the cord rotates in a circle six times, then to tighten the spring, you need to turn the coil by the clock six times. After that, you just need to let the rope through the hole and fix the handle on the cord.

Assembly and installation instead of a starter

To collect the starter and install it in the same place, you need:

When assembling, be sure to install both goals, otherwise after some time the plastic cup will be damaged by the spring, and when the cord is stretched, the user will notice that it jammed. It looks like spring has come. To correct such a breakdown, it is necessary to install a larger screw or another washer. If you cannot find the details you need, just unscrew the screw slightly, and the starter will no longer jam. However, you must understand that these are temporary measures and that you should correct the problem as soon as possible.

Prevention of problems

Sooner or later, problems with the starter arise on any trimmer. STIHL FS 55, MTD 790 or other brand

This malfunction can be postponed, but the tool should be treated carefully. In particular, do not make too sharp jerks, it will break the cord or spring

It is not recommended to expose a brush to impacts or other physical influences. In the case of a breakdown of the starter case and the cut of the cord, it can be wound on the engine flywheel. It will break the pulley and break the spring.

Therefore, having discovered that the executive mechanism has broken on the uterus, do not immediately rush with the help of specialists. Knowing how to eliminate problems and / or replace the details, you can carry out repair work yourself. This does not require a special tool. At first, the procedure may seem complex and tiring, but numerous online video on the repair of the starter can help you solve the problem as quickly and easily as possible.

The best gas braids for grass

Trimmer for Husqvarna 128R grass on Yandex market

General principles of tuning

If you relate to your trimmer with care and attention (when maintaining and choosing consumables), then it will thank you for years dashing and reliable work

Removing and disassembling the starter, replacing broken parts

To repair the starter of the trimmer for the grass, you will need to disassemble it first, and then collect it. This process is not a particularly difficult occupation. For work, you will need a screwdriver with the tip of the desired shape.

Everything should be done carefully, observing safety precautions, mainly that the spring does not injure the master if an accident.

Parsing the starting node

They disassemble the launch mechanism in order to install new parts instead of broken in the following sequence:

• spin a screw with a screwdriver, fixing the pulley with a starter lid;
• take out a spring and antennae;
• Remove carefully with the pulley (you need to unscrew the head or work, having dressed the glasses and gloves before);
• determine why the launch mechanism has broken;
• If the spring collapses almost completely, then it is replaced;
• When the spring exits from the hook, it is installed in the original place, bending the antennae before this (the photographs show the laying process);

After the spring plate is installed inside the groove, it is carefully twisted. To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst

Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges

To change the spring, you should work carefully and accurately: it can, under the influence of the effort caused by the installation of it in place, accidentally burst

Even if you carefully remove the video, then the spring strip flies very quickly from the coil and can injure your hand with its sharp edges

Immediately putting a springy plate in the same place does not always work. It often slips, so attempts are required to repeat until the desired result is achieved.

Starter assembly

The assembly of the starting node is carried out in a number of stages:

The coil is turned over, installing it so that the spring bend exactly stands into the groove of the case, as in the photo below;

When making the stated manipulations, it is necessary to lay two goals. If this is not done, then the spring over time damage the plastic cup, and when it is pulled. Because of this, a feeling appears, as if the spring had flown. To eliminate such a drawback, you need to install this part of a larger length or an additional goal.

When such spare parts are absent, you can just unscrew the screw a little, and the starter knot will begin to work without shaken. But this option is temporary. it is better to repair qualitatively as quickly as possible.

Spring tension

After installing the spring, it should be pulled. The following actions are performed for this:

• Remove the handle from the starter cord;
• Then the rope is inserted into the coil groove;
• They stretch the spring, rotating the coil in the direction opposite to the clock of the clock arrow (reviews);
• make the desired number of revolutions specified in the instructions for the use of the trimmer model used and the corresponding length of the cord used;
• At the very end, the rope is threaded into a hole designed for this, located in the starter cover;
• put the handle in place, fixing it with a node.

If after the repair the spring continues to fly, then you can get rid of this in the following ways:

• Squeeze the suitable piece of the plate into the groove at the location of the spring hook;
• drill holes on two sides of the groove in the coil, into which the spring hook is inserted and fix it using a wire.

Replacing a torn cord

A torn rope is replaced in the following sequence:

• The old cord is removed;
• choose a suitable rope (thickness and length);
• Having reached it through a special hole in the coil, a knot is tied;
• Sprinkle a spring, producing the required number of revolutions;
• Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way

In this case, there are some nuances associated with their constructive features.

How to pull the spring

Spring repair

If the material of the starter spring is poor.quality, the spring bursts (usually at the place of its connection to the drum, where it forms a loop). Replace the spring in this case is not worth. Carefully clean its surface from dirt and traces of lubrication, gently polish the destruction place, and then release the spring at 600 650 ° C (the spring steel should purchase raspberry color). It is necessary to cool the spring slowly, and at 100 150ºС you can already carefully wrap its end in the shape of a restrictive protrusion on the inner surface of the drum (steel will acquire the necessary plasticity) and insert into place. Simple repair of the starter of the chainsaw of Repair Starter Chainsaw how to pull the chain on. The elastic properties of the spring will not change.

Tightening the spring PIM

The spring is pulled with a canvas worn on the drum. The tension and configuration of PIMs are made according to the following algorithm:

• Traction springs are put on the canvas (they are included);
• The spring mechanism is pulled (the number of revolutions depends on the diameter of the shaft and the mass.body characteristics of the canvas. you can find out the approximate number of revolutions from a special table);
• The spring is fixed with special brackets;
• traction springs are refueled in a shaft in special slots located at its ends;
• The lock of the spring is removed;
• The smoothness and speed of the canvas is checked (it is necessary to hold it with your hand to exclude sharp blows of the stoppers on the lower lamella on the edge of the box and, if the stoppers have not yet been installed, avoid complete winding of the canvas on the shaft).

Practical recommendations

In order to compare holes for fixing the cord in the pulley and the case, you may have to make a few more turns. A new rope is threaded into a technological hole and make a loop or knot: this will allow it to slip out of the pulley. The rope is taken to the side so that it does not interfere with further work. Next, it is necessary to fix the pulley.

First you need to install a smooth launch spring in place. It can be used the same if damage is not detected in it. or new replacement if necessary. A starter clamp is installed on top of the spring, which is fixed with a special screw. In the article we will tell you how to adjust how to adjust the carburetor on a video chainsaw. He reliably fixes the clamp for a long time, avoiding its distort and swing. I have a carburetor mounting stilettos on a chainsaw, how to change it? After that, you need to make a few turns of the rope and start it inside. The cover with the assembled starter is installed in place. With the help of screws, it is fixed.

After the repair and assembly is completed, you can start work. Self.repair of the starter does not take much time and does not require complex skills, but saves time and money if you perform such work in the service center.

It is necessary to approach the repair of the chainsaws responsibly and timely to carry out preventive examinations, monitor the quality of the fuel and oil used. These simple manipulations will increase the duration of the tool in working condition.

Spring repair

The procedure for repairing the start of the launch system:

• Dismantle the starter from the tool.
• Remove the protective cover.
• Wind the cord from the end of the pulley to avoid scrolling the mechanism.
• Pass the second end of the cord in the hole of the protective cover.
• Pull the cord 17-20 cm to check the turn of the pulley of the spring mechanism.
• Check the operation of the spring after stretching and releasing the mechanism.
• Unscrew the circle circle from the side of the generator, removing 3 fasteners.
• Demolish the pulley and cord.
• Check the condition of the parts for wear and the presence of damage and cliffs. If the cliff is small, then you can eliminate the defect by welding.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections

Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Preparation for replacement

For clarity, a mowing head was removed from the motorcycles (Spool). To replace the fishing line you do not need to remove it, everything is done in place. It doesn’t take much time.

We disassemble the rogue of the trimmer for the grass-it holds on the clan locks. Remove the lid, pressing on the latches. If you do not have enough effort with your hands, then use the screwdriver.

The principle of action is as follows. By clicking on the button, the coil presses on the spring and leaves the fixing grooves in the lid of the spray. Holding the coil in this state, you can twist, thereby adjusting the length of the fishing line. When the button is released, the housing spring returns the coil to the original fixed state.

Repair of the bar motorcosa. Primary diagnosis of a trimmer for grass.

The proper operation of the engine and the lawn mower in general is affected by a huge number of factors that are usually interconnected. If you fail to determine the malfunction, contact the proven service center.

I would like to note that before proceeding with disassembly and serious repair, you should check elementary consumables. These “little things” often affect work and, perhaps, repair of a trimmer for grass will cost “small blood”, so to speak.

Spend of the ignition-lack of soot, electrode clearance (0.5-0.6mm-or according to the instructions), good spark

Fuel filter. lack of pollution, mechanical damage, good throughput. Periodic replacement according to the maintenance schedule in the operating instructions

Air filter. lack of sawdust and pollution. Periodic cleaning in soapy solution and purge under high pressure. Replacement of the air element according to the instructions for the expulsion

• Cozy and stylish chair with your own hands.
• Home sausage in foil.
• Tips for all occasions!
• How to insulate the attic?
• Cucumbers for May and cucumber secrets of seed collection.
• Salt in the garden.
• Interior design of kopecks for evaluation.

• Do.it.yourself. How to repair a lawn mower if a motor does not start
• Repair of the bar motorcosa. Primary diagnosis of a trimmer for grass.
• Device motorcycles. Gasoline trimmer device for grass
• Repair of Chinese motorcycles. The design of the lawn mower
• The first launch at the beginning of the season
• Video repair of lawn mowers with your own hands: analysis of malfunctions and methods of their independent elimination

Replacing the omentum of the Chinese trimmer for grass from the side of the starter:

We unscrew the spark plug, block the movement of the piston with a stopper. Remove the starter (p.31). 13mm with a head of 13mm we unscrew the starter ratchet (p.35). Traces of a gas mixture on the omentum indicate its necessary replacement. With a thin flat screwdriver (awl, or any similar object that is at hand) we remove the old oil seal (p.36), pry it with a screwdriver from the side of the crankshaft and remove it.

We apply a small amount of oil on the inner surface of the new omentum before installation (you can use oil, which is used to prepare a gas station)

We blow out and degrease the seat under the oil seal, evenly install a new oil seal.

Replacing the oil seal of a gasoline trimmer for grass from the side of the flywheel:

We unscrew the spark plug, block the movement of the piston with a stopper.

For convenience, remove the crankcase cover (p.58) unscrewing 4 screws (p.61)

Unscrew 2 clutch mounting screws (p.57) with washers (p.56), remove the clutch assembly and the washers under it (p.53)

Unscrew the nut (p.52) flywheel (p.51), but not to the end. Not a strong blow to the nut “knock him off the crankshaft”. Unscrew the nut, remove the flywheel and the veneer. We will examine the surface of the oil seal. traces of moisture, or wet pollution, scuffs and other damage on it are a signal to its replacement.

With a thin flat screwdriver (awl, or any similar object that is at hand) we remove the old oil seal (p.50), pry it with a screwdriver from the side of the crankshaft and remove it.

We apply a small amount of oil on the inner surface of the new omentum before installation (you can use oil, which is used to prepare a gas station).

Replacing the seals of the Chinese trimmer for grass.

One of the main causes of air leaks into the engine are crankshaft oil seals. In general, this problem is the most common on Chinese trimmers, and in some cases, seals begin to pass the air in the first year of service. All the fault of low.quality rubber products of such mowers, well, no one has canceled natural wear.

Essle for different sizes were installed on both sides of the crankshaft (12227mm small and 15307mm large). You can safely sin on the seals if it begins to “snot”. Another indicator of their malfunction is floating turnover when working for “hot”. Next, we will consider in detail the process of replacing.

Starter repair work

Problems with the starter may not ensure the launch of the tool. That is, after stretching the cord, the chainsaw does not begin to work.

Before repairing the starter, you need to prepare the tools with which you can do the work:

• Set of screwdrivers or special tools that are supplied with the manufacturer of the tool;
• A rope that will be used as a replacement of a torn cord if necessary.

A large amount of black soot on the spark plug indicates an engine malfunction.

The starter must be removed from the tool body before direct repair of the starter. To do this, unscrew a few screws that hold the side cover to which the starter is attached. This is done using a screwdriver or a special tool.

After unscrewing the lid, it is turned over and examined. Next, unscrew the screw with which the starter is attached. After that, the clamp and the spring are dismantled for smooth launch. The pulley, on which the cord is wound, is now available for removal. As soon as the knot on the cable is unleashed, it can be removed from the pulley and replaced with a new. Provided that the loss of the starter’s functionality is associated with a breakdown, this may be enough to eliminate the malfunction. Nevertheless, the rest that make up this element of the chainsaw should be carefully examined.

When examining the components of the starter, you can find the following malfunctions:

Most often, damage to the smooth starting spring occurs from the end, where this is visible when disassembling the case.

• The pulley can be damaged. There may be cracks or tears, as well as damage to the back. Because of these problems, the tool cannot do the work.
• Damage to a smooth starting spring. In this case, the spring itself can be mechanically faulty, and defects may occur at the mounting site. The weakest place of this element is the place of fastening and the tip of the spring, which is inserted into it.

If faulty or partially damaged starter details are detected, they must be replaced with new. In this case, the new elements must correspond to the model of the repair of the saw.

After the repair, the starter must be properly assembled.

The pulley is installed on the spring. In this case, you need to check how they are interconnected. The pulley must be wrapped to continue repairs. This must be done so that during rotation he pulls the cord into the starter. It is enough to make 3-4 turns to give the necessary voltage. Pre.pass the rope through the hole in the chainsaw cover.

MTK 28 DIY repair

Details: MTK 28 DIY repair from a real master for Olenord.com.

How to disassemble the motorcosa Hammerflex

MTK31 Hammerflex gasolimmer, equipped with a two.stroke engine, allows you to mowed herbal cover, thick weeds and small bushes in the shortest possible time. The lawn mower is normally suitable for the repeated introduction in the garden, in a summer cottage or personal plot (including huge areas). Such a cheap tool is the best solution for maintaining lawns in proper form.

Technical characteristics of the Hammer MTK31 Hammerflex Benzotrimmer

• Power: 1.2 kW
• Motor volume: 34 cm3
• Number of knife blades: 4
• Reza width (knife / fishing line for trimmer): 230 mm / 430 mm
• Fuel tank volume: 0.5 l
• Field dialect: 2 mm
• Mass: 6.8 kg

Description of gasoline braids for Hammer MTK31 Hammerflex grass grass

This model was made according to European standards, has certificates of GS/EPA/CE/EMC, highly spent, durable and ordinary in use. The number of harmful exhaust emissions is minimized and does not pose a threat to health and environment. For comfortable long.term work, there is a shoulder belt. The device is rapidly starting, trivial in management and does not ask for experience working with it. For a trimmer head, automatic fishing line is provided. This powerful and reliable model is equipped with a frisky and accurate adjustment of the working characteristics, produces a minimum of noise, and economically consumes the fuel mixture.

A detailed description of the repair of the starter of the trimmer for grass for the example of Hammerflex.

A straight collapsible bar with a curved double handle is characterized by increased strength and provides comfortable work in open areas. For a four.lobed knife, as well as a trimmer head, there is protection against possible damage during transportation.

Great traction and high torque significantly increase the total speed and performance of work. A wide deflector increases the level of security during the work on the work.

If necessary, pumping fuel into a carburetor can be carried out manually. using a special pump. This possibility allows you to quickly start a motorcycle after prolonged downtime. Smoothly lightweight launch does not require any effort due to a special decompression system. Rubber buffers provide a reduced level of vibrations that occur during operation.

To increase the durability of the engine in the design of the benzotrimmer, a reliable air filter is provided. Motokos can be stored in any position.

Dear forum users. Maybe someone has come across such a problem. The cord is confused to start the engine to provide access to remove the clutch coupling. How to remove it is a question?

Good day! I decided to raise the topic, t.I faced the same problem on a similar spit. If someone sorted it out, please tell me., how to remove clutch clutch to get to the starter?

P.S Unfortunately Google and the search did not help.

Look at this topic, it can help))) ”Good luck!

Vladimir. Class, like it, tomorrow I will try. Thank you very much. ))

GSG wrote: Dear forum users. Maybe someone has come across such a problem. The cord is confused to start the engine to provide access to remove the clutch coupling. How to remove it is a question?

First remove the clutch cup. She is attached to the crankshaft with a screw. This screw is not visible, but it is there. In short, in the square hole, which includes the shaft of the bar, you need to insert a standard key-star (it comes with a scythe). Remove the cup, the clutch itself unscrewed with my hand.

GSG wrote: Dear forum users. Maybe someone has come across such a problem. The cord is confused to start the engine to provide access to remove the clutch coupling. How to remove it is a question?

First remove the clutch cup. She is attached to the crankshaft with a screw. This screw is not visible, but it is there. In short, in the square hole, which includes the shaft of the bar, you need to insert a standard key-star (it comes with a scythe). Remove the cup, the clutch itself unscrewed with my hand.

How to eliminate the backlash between the basket and the clutch on the Stern motorcycle?

Good day. Lawn mowed MTK-31 Hammerflex. Starts, works for a while, begins to choke and stalls. Even after I drowned it myself, I hear some kind of hiss in the candle area. I twisted the candle, it is wet. I don’t even understand what reason this could be. Tell me please. Thanks.

A detailed description of the repair of the starter of the trimmer for grass for the example of Hammerflex.

Life in the village. All of our https: // goo.GL/3F9C4V The video was shot on the SJCAM4000 camera: http: // ali.PUB/PIKCM

He took off the cylinder and saw an air leak through the cylinder laying

Cooking the fuel mixture for two.stroke engines along with the technical specialist of the company TMK. Before preparing the mixture, be sure to read the instructions of your tool. You can buy garden equipment, you can in our online store https: // www.TMKTools.ru/we are on social networks: https: // vk.com/tmktools_official https: // wwwcom/tmktools/

How to wind the cutting cord to the coil of motorcycles (trimmer for grass)

This video will help you in choosing the necessary motorcycles for you

How does the compound work on the bar now after three years?

I was honestly surprised when you doubted the reliability of the connection, t.to. I know that this is a certain plus, t.It’s very convenient for transportation, and by reliability no worse than a whole rod, I’ve been convinced for several years on my spit.