Internal skirting board how to cut

Polystyrene

Polystyrene has the same properties as Styrofoam. Therefore, polystyrene skirting boards are cut in the same way as foam ones. The main thing here is to sharpen the cutting edge of the tool as sharp as possible to avoid chipping. At the same time, there is no need to process the ends with sandpaper: their edges are usually already sufficiently embossed to ensure good adhesion of the glue.

internal, skirting, board

Cutting polystyrene with a miter box

How to properly trim a floor plinth

Floor skirting boards can be made of PVC, polyurethane, wood or MDF. As in the case of the ceiling plinth, they need to be cut, depending on the material, with an ordinary hacksaw (wooden) or a hacksaw for metal (plastic).

Now you know how to saw down the ceiling plinth. Next, let’s see how the floor trimming and trimming is done. How to use the miter box in this case? When trimming the floor plinth, the procedure is approximately the same as when trimming the ceiling. For the inner corner:

  • We take the first strip and put it in the tray from right to left so that it lies in it in the same way as on the floor. We lean it against the far wall of the instrument as against a wall;

The strip is inserted into the tray and pressed firmly

  • We trim the unnecessary piece from the left end at an angle through hole 1 (picture below);
  • Insert the second strip from left to right in exactly the same position and cut from the right end through hole 2.

How to Install Baseboard / Skirting Boards.

How to cut a skirting board in a corner if it is external:

  • Insert the first strip into the tray in the same way as for the inner corner (from right to left);
  • We cut it from the left end through hole 2;
  • Insert the second plank from left to right and cut its right end through slot 1.

How to cut a ceiling plinth for outside and inside corners

Next, we mount the planks in the corner of the room.

Tip: The end at an angle of 45g should be done not only in order to cut the elements in the corners, but also for making joints on the wall itself. In this case, the connections will not be as noticeable.

Thus, we have examined in the most detailed way how to cut a plinth in the corners. This procedure is not as complicated as it might seem at first glance. By starting trimming in a miter box or by imitating it, you will see for yourself.

What are the baseboards

Before figuring out how to glue the ceiling plinth in the corners and make inconspicuous joints, you should find out what to look for when choosing:

  • polyurethane ceiling plinth is considered the highest quality material for the manufacture of ceiling plinths, but you can find PVC and expanded polystyrene on the market, as well as wooden and gypsum fillets;
  • the length should be standard. from 1.3 to 2 m, the rest can be considered scraps or unformatted;
  • when pressing on the surface of the corner of the ceiling plinth, there should be no dent. otherwise we can talk about low quality;
  • the style of the edging is thought out even at the stage of choosing and gluing wallpaper so that it is in harmony with the interior.

Sizes of baguettes and corners

You shouldn’t buy material from spontaneous markets or questionable suppliers, even if they offer such tempting prices. A ceiling plinth glued to a corner made of low-quality material can seriously spoil the impression even of an expensive repair.

Manual trimming of skirting boards

If it is not possible to work with the miter box, a different method should be used. Before making a corner on the ceiling plinth, it is advisable to practice on a fillet dummy. You can use trimming products left over from previous work.

According to experts, trimming the skirting board without using a miter box is more accurate, since it allows you to more accurately and more correctly outline the angle to be created. In this way, it is more convenient to create an inner corner at the ceiling plinth. There are also disadvantages to manual trimming. it is difficult to keep a wooden or polyurethane fillet in weight when taking measurements.

The sequence of actions will be as follows:

  • With a pre-prepared tool, two workpieces are cut at right angles.
  • Then the plank is applied to the ceiling so that it rests against the wall, which is perpendicular to the plinth. With a pencil directly on the ceiling surface, draw the contour lines of the dumbbell.
  • Do the same with the adjacent bar and lean it against the ceiling in the same way and draw a line with a pencil.
  • After that, you need to carefully look at the resulting image. The point of intersection of the lines will become the place where the skirting board should be cut. It doesn’t hurt to play it safe. To do this, reapply both dumbbells to the ceiling and on the products themselves mark the place for trimming. A line is drawn from this place to the other end of the plinth. Then, according to all the marks applied, fillets are cut.
  • After the trimming process is completed, they are joined together and applied to the ceiling where installation is planned.

If, after the outer corner has been made, the ceiling plinth looks uneven, there are gaps, gaps or other errors, you should not rush and redo all the work. A sealant or putty will help to eliminate the shortcomings. They can accurately and quickly fill the existing voids without spoiling the appearance of the fillet.

How to properly trim a floor plinth

However, naturally docked planks usually look more harmonious. And in this case, you will not have to spend money on additional parts. Therefore, further in the article, we will consider how to cut the corner of the ceiling plinth correctly and how to process the seam.

Tip: The end at an angle of 45g should be done not only in order to cut the elements in the corners, but also to make joints on the wall itself. In this case, the connections will not be as noticeable.

But in order for the ceiling plinth to look really beautiful, you need to be able to qualitatively join its corner joints. How to cut the corners of the ceiling plinth evenly can be found in our article.

Related article: how to properly glue the ceiling plinth with glue and putty.

Professional miter box with swivel hacksaw The miter box usually looks like a tray with vertical holes for a hacksaw. It can be made of wood, metal or plastic.

This tool is the oldest and simplest carpenter’s tool for cutting wood pieces at 90 ° and 45 ° angles. There are types of such a device for professional work, with a rotary mechanism, in which the cutting tool can be rotated and fixed in any position.

How to properly cut the ceiling plinth Ceiling corners are divided into internal and external, the method of joining them is slightly different.

Installation of plastic corners

The work on installing plastic corners on slopes is as follows:

  • Regardless of where you need to glue the plastic corners. on the door, if a casing or window is not provided, outside or inside, you need to make measurements and cut the material to length correctly.
  • Prepare the surface where gluing will take place. remove unnecessary elements, clean the base.
  • Install and glue the strips correctly.

How to properly glue plastic corners to any slopes:

  • Degrease the surface well before attaching the corner piece.
  • Polyurethane foam is not used in the design process.
  • Excess protruding plaster is smoothed out to a noticeable smoothness.

How to glue plastic corners correctly

  • The sticker provides for marking with a pencil.
  • Before you glue all the details, you should use the advice: it is better to measure the corners for the slopes of doors and plastic windows locally. Place the top horizontal element first, and then use the cutting tool to mark the vertical stripes.

Sheathing with corners also implies additional fastening of the strips using narrow masking tape. Fix the strip with it in several places and leave it for about 24 hours. This time is enough to reliably glue the corners to the surface.

If the corner is used as a finish, then the place of its gluing should be cleaned of finishing materials. Thus, the grip quality is increased. When fixing on an area decorated with trellises, a strip should be cut a couple of millimeters wide than the plastic corners. Adhering to simple design rules, fixing decorative elements will be simple and quick, and in the end they will delight you with an aesthetic and relaxed look.

Cutting features

Let’s take a closer look at how to properly cut a corner on the ceiling plinth using a miter box using different materials.

Wood

Wooden skirting boards are not common and are expensive, so you need to be extremely responsible in their processing. Cutting technology looks like this:

  • The end to be cut is fixed in the miter box.
  • The cut is made. This can be done with an ordinary wood hacksaw, but it is better to use a special saw or metal saw to avoid cutting too wide.
  • Edges adjust in place. If necessary, they are ground with a belt machine (or a drill with a grinding attachment), or cut.
  • The skirting board is fixed in place with glue or self-tapping screws.

Asterisk IMPORTANT: when adjusting, you need to be extremely careful; it is better to close the uneven cut with a decorative overlay or wood filler than to chise out too large an array of wood

A plinth made of plastic (polyvinyl chloride, PVC) is now widespread. It’s convenient because:

  • Easy to cut with any tool.
  • Flexible, can be used even in uneven corners.
  • Usually it has internal cavities, which means it can be used as a cable channel for laying electrical wiring or fiber-optic lines for the Internet.

PVC skirting board has proven itself well

PVC skirting boards are cut in the same way as polyurethane. However, one must take into account: the best tool, a hacksaw for metal with fine teeth, is suitable only for thick skirting boards, in thin ones it can pull out pieces. Therefore, the best option for thin products is a stationery or construction cutter or a sharpened knife. To use it, you need a certain skill, so it is better to practice in advance on scraps or sheets of thin plastic.

If there was no miter box

If your walls are not perfect or there was no miter box in your house, it is better to use other methods, without using a special device.

The algorithm of actions is as follows:

  • The ceiling plinth must be attached to the place of gluing and the necessary measurements must be made.
  • After the fillet, you need to put the top on the bottom of the miter box tray. In this case, the lower part of the plinth must be pressed against the wall of the tool.
  • Next, you need to cut the skirting board at an angle of 45 ° using a saw or knife. When cutting, it is important not to overdo it with pressing force, as chips may remain on the plinth.
  • So you yourself need to cut off the butt skirting board, at the same angle.
  • At the end, you need to dock adjacent fillets at the gluing point, while adjusting the cut line with a knife.

For those who are doing this procedure for the first time, experts recommend practicing on trimming skirting boards.

Cut off the outer corner

If everything is not so difficult with the inner corner points of the room, then how to cut the ceiling plinth in the corners, if it is outside? To begin with, it is advisable to mark the inner baguette. this is necessary in order to avoid a situation when the required bar is not enough in length. To do this, you need to attach the bar to the ceiling itself and outline its dimensions.

So, the markup is done, you can get to work:

  • Install the skirting board by pressing it against the nearest wall, hold it with one hand.
  • Select a 45-degree hacksaw position when the handle is close to the hand holding the workpiece.
  • Cut the workpiece.
  • Cut the striker in the same way.
  • Dock corners.

to the content

How to trim ceiling plinths in corners?

The plinth, which is attached to the ceiling, performs, first of all, an aesthetic function, separating two planes. the walls and the ceiling itself. However, besides this, such a detail implies another important function. sometimes it hides the errors in wallpapering or finishing the ceiling. Of course, the skirting board will not fit harmoniously in every interior design, but in most cases the interior will look incomplete without using this detail. In this article, you will learn how to trim ceiling plinths in corners using the tools at hand.

Wooden skirting boards are not common and are expensive, so you need to be extremely responsible in their processing. Cutting technology looks like this:

  • The end to be cut is fixed in the miter box.
  • The cut is made. This can be done with an ordinary wood hacksaw, but it is better to use a special saw or metal saw to avoid cutting too wide.

Asterisk IMPORTANT: when adjusting, you need to be extremely careful; it is better to close the uneven cut with a decorative overlay or wood filler than to chise out too large an array of wood.

A plinth made of plastic (polyvinyl chloride, PVC) is now widespread. It’s convenient because:

  • Easy to cut with any tool.
  • Flexible, can be used even in uneven corners.
  • Usually it has internal cavities, which means it can be used as a cable channel for laying electrical wiring or fiber-optic lines for the Internet.

PVC skirting boards are cut in the same way as polyurethane. However, one must take into account: the best tool, a hacksaw for metal with fine teeth, is suitable only for thick skirting boards, in thin ones it can pull out pieces. Therefore, the best option for thin products is a stationery or construction cutter or a sharpened knife. To use it, you need a certain skill, so it is better to practice in advance on scraps or sheets of thin plastic.

Polyurethane

Polyurethane foam (in common parlance. just polyurethane) is a very good material for ceiling skirting boards. Due to their good flexibility, they adhere exactly to the base (the junction of the wall and ceiling), even if the walls and ceiling are uneven due to construction errors. In addition, polyurethane is easy to clean and therefore can serve for a long time. Low load resistance is not a problem here: there are almost no loads on the ceiling plinth. We also have a separate article, where the question of how to make a plasterboard ceiling and suspended plasterboard ceilings is discussed in more detail.

Cut the polyurethane plinth with a miter box as follows:

How to Cut & Install Skirting Board, Baseboard Internal Corners

  • Measure the wall and ceiling in the junction area.
  • Choose a suitable template on the cutting table.

Using a miter box at home

The easiest way to adjust the strips of the skirting board is to cut it with a miter box. This device is a U-shaped structure (something like a box without one of the walls). In the sidewalls of the miter box, cuts are made in advance, which are later used as a template for cutting off both the plinth and other materials.

Cutting the plinth at an angle using a miter box, see this video.

The miter box has the following advantages:
  • It allows you to accurately cut the edges of the skirting board according to the finished template.
  • It is easy to do it yourself using four planks, a square and a saw. At the same time, you can cut through the template grooves for every taste, depending on the required type of work.
  • It makes it easy to form both inner and outer corners.

The only drawback of this method concerns only those cases when the miter box is made by hand: it is necessary to be extremely careful, in advance to outline the lines for the template slots using a protractor, without deviating a degree.

Cutting a corner on a ceiling plinth using a miter box has its own characteristics. You may also be interested in reading an article on the topic, plastering walls with your own hands, types of plaster.

How to cut a scribe/cope internal corner on skirting boards or baseboards

Cutting features

Let’s take a closer look at how to properly cut a corner on the ceiling plinth using a miter box using different materials.

Styrofoam

Polyfoam is also often found as an element of the decoration of rooms. Its characteristic feature is increased fragility, therefore, it must be adjusted in place very accurately, the foam does not tolerate any deformations.

You need to cut it with a miter box as follows:

  • Plinth plates are stacked in the miter box.
  • An incision is made. Unlike polyurethane, foam is a soft material, and it can be cut even with a knife or, better, with a stationery or construction cutter. Here it is better to use a small, but even piece of wood, a metal plate or a ruler. As a last resort, you can make pencil marks corresponding to the slots of the miter box, connect them with a ruler. and lead the slot.

Asterisk IMPORTANT: Styrofoam is a brittle material, so the cutting tool should be sharpened as best as possible.

External

For the outer corner. the plinth is applied to the right side of the miter box (or to the one closest to you, if the template is placed across the desktop), aligned along the plane and the wall, and then cut off or sawed off using the template.

Decorative caps

Another option for sealing joints is to use decorative caps for internal or external corners. Both types are usually sold in the same place as the skirting board itself and are more likely to match in style and color. In the event that plastic and foam baseboards are used, corner and end caps are a necessary finishing detail.

When using decorative corners on a ceiling plinth, the installation looks like this:

  • The skirting boards are applied in place and trimmed. Accuracy of fit does not matter, if desired, you can cut at right angles.
  • The plug is applied to the corner.

How to make a corner on a skirting board using a miter box. step-by-step instruction

ReLend.ru »Repair technology» How to make a corner on a ceiling plinth using a miter box. step-by-step instruction

Ceiling plinth is a decorative element that separates the wallpaper or tile from the wallpaper on the wall. It completes the look of the room and completes the decor. However, in order to correctly join the two strips of the skirting board in the corner, it is necessary to cut it off correctly. How exactly is this done? There are several ways to achieve your goal.

articles [hide show]

Articles , ,