Is it possible to cut a laminate with a jigsaw. Devices for sawing

Laminate with a jigsaw

In some cases, for example, at the junction of a laminated board with pipes, it is necessary to make a saw of a certain shape, which is called figure. Theoretically, you can make such a cut with a hacksaw and a circular saw, although an electrician is a universally recognized leader in operation in operation.

I would like to pay special attention to laminate files, which are used together with the jigsaw:

• The goal is a quick cut: if you need to cut many boards at once in a short period, then it is better to choose an option with a large tooth. The fact is that the larger the tooth will be, the faster the work will proceed. The only negative is that the cut will be less accurate, the cut is not hot. For such a purpose, as a rule, they buy a T101D marking tool, since it is suitable even for a thickness of 75 mm. For 100 mm, choose 244D, 200 mm. 344D;
• Purpose. Clean cut: here you need to use the option T101B. It is characterized by a smaller tooth, the poet cut is more smooth. In this case, chips are absent. Of course, even 75 mm can be cut with such a file, but it will take several times more time.

The laminate saw is equipped with a back tooth, which, when compared with other options, is directed in the other direction. Why is it necessary? This is done so that chips do not form on the front side of the lamella and the appearance does not deteriorate.

!Such boards can easily be sawed with a small divorce and moderate teeth. In this case, the speed of the jigsaw should also be moderate. So the tool will not introduce and will not break the edges.

Method 1. You can use a hacksaw or circular saw with a maximum number of teeth to avoid the appearance of chips. First make markings and mark the part of the board you are going to cut off. This can be done both with the help of chalk and a pencil. Erasing chalk then very simple. Well, then just cut the lamella along the marked line.

Method 2. You can also use an electrician. This option is several times simpler than the previous. Fasten the guide on the device, and then make it out the edge of the workpiece. In this case, the movement of the file will be even relative to the edge.

!You work with thin lamella? Be prepared for the appearance of chips on its front part. The fact is that in the first version the tool will move up. To prevent such an outcome, you can place the blank with the front side down. Another way out is the use of anti.Slip lifers.

How to cut a laminate on a curve correctly? For such work, only an electrician with a special canvas with very small teeth for laminated floors or even with a standard canvas is suitable. A special option is better, as it helps to cut up the pattern up and without chips.

• First prepare the desired paper or cardboard template. It is needed in order to calculate the cut and maintain the integrity of the board;
• Attach the template and circle the desired pattern;
• Cut the pattern and again attach the template to make sure of its accuracy;
• Now just circle the sample along the contour on the surface of the lamella;
• Make a drink. If you use the standard canvas, put the board with the pattern down and attach the template upside down. Keep the jigsaw only vertically. If you need to cut it with the front side, stick a strip of paint tape on the cut line so that you do not have chips when cutting. Then measure the lines on top of the tape on which you are going to saw the lamella. For this, a special canvas is used, intended for such floorings.

!Sometimes the template must be applied several times so as to get a sample of the desired shape. In this case, it is important not to rush: devote the time to the manufacture of the template, and then you will spend less time and effort to cut the boards.

Do not try to use a hacksaw in the case of curly cuts. You will not achieve the desired result and only spoil the material. First, decide on the option of cutting (curly or straight), and only then choose the better to saw laminate.

Video than cut a laminate?

Features of choosing a file for a laminate for a jigsaw and an electrician are divided into:

If you need to cut the laminate using an electrolobian, then it is better to choose files with small cloves. In some cases, a tool with a reverse arrangement of teeth is used, which significantly reduces the likelihood of cracks and chips on the front side of the materials. A very important point is the tail of the file that is used in your jigsaw. However, in addition to individual models, there are “omnivorous” devices that fix the cutting parts of any kind.

Bosch electric laminate saw have many popular models, including T101BR. It is standard and has a reverse location. When using this file, the front side of the laminate does not suffer and does not break, so that the cuts are neat and smooth.

• T101B. The model has direct.Focused small teeth, which ensure the smoothness of the cut. It is used for accurate and even cut, without chips. In addition to the laminate, it is used for sawing plywood, chipboard and fiberboard.
• T101VR. This model is practically no different from the previous one, but there is one raisure in it. The letter R in the name indicates that the teeth are directed in the opposite direction. This introduction allows you to exclude the appearance of cracks and chips on the front side of the panels. Thus, the appearance of the coating does not deteriorate, and the sections are clean and neat.
• T119BO. Suitable for curly cutting (sawing circles, radii, bends) of laminate and wood. Their shape is fundamentally cast from straightforward models, because in the bends and turns, it should not be clamped. However, the T119BO model is not one of a kind, in addition to it, there are other models that are designed for figure cutting. Each of them has the letter “o” in the name.

We take a hacksaw in your hands

The laminate of the hacksaw, of course, will cut, but it is not very suitable for such work. After all, the teeth of a hacksaw designed for wood work are frighteningly large, and the upper floor of the flooring is so thin. Togo and look. Ugly traces will remain from these teeth. And cutting the pressed structure of the laminate is hard. Hands get tired.

How To Cut Luxury Vinyl Planks with Saws and Laminate Cutter

To get a good result, we arm a hacksaw with small teeth. For example, a hacksaw designed for cutting metal may well fit. CHARS on the cut will be avoided, but it will be more difficult to cut fine.Toothed with a hacksaw than a tool for wood. However, if you do not intend to saw the laminate in large quantities, then this method is suitable. The quality of the cut, of course, is not perfect, but quite tolerable.

Death Trap (Lego Horror Movie)

And here are the promised little tricks: before sawing, stick a piece of painting tape to this place. If you do this, then chips are not formed at the site of the cut. Over, the laminate board must be placed upward. And to make the cut smooth and clean, the hacksaw must have small frequent teeth.

Since the laminate is pressed using special mechanisms, it is natural, it is better to cut it not manually, but an electric tool.

For example, for this, an electric burner is quite suitable, (saber’s saw) which is increasingly used by home masters.

How to cut a laminate with a jigsaw. The right files solve everything

It is light and mobile, you will quickly learn to work with it. This is how to cut a laminate is really convenient. Here is the main solid hand (so as not to drive to the sides) and the selection of files. Which side of sawing will we figure out further.

How to cut a laminate with an electrician:

It is very important what pieces to cut laminated boards. There are special on sale. For laminate

But if you did not find them in trouble. So that there are no chips on the front side, make markings and cut it on it. And then we just use a file with teeth that are directed down. It is she who provides almost the perfect cut. All chips will be on the bottom of the lamella. But you have only a saw with teeth at home. In this case, we make markings and saw on the back side. That’s the whole secret. Some still use metal files.

• You need to cut the laminate in another room. There will be a lot of sawdust. By the way, they are scattered differently depending on the file. Cloves up. Sawdust up and vice versa. This is that sometimes you need to put on glasses;
• You need to hold a piece that we cut off. Since at the end of sawing it can tear a piece of coating from above;

A jigsaw can be sawed laminate not only in length and width. You can easily perform curly cutting with rounded corners. For example, make a beautiful drank for a pipe.

The capabilities of the tool

An electric jigsaw for cutting a laminated board must have the following characteristics:

It should be possible to perform a tool even and pure cut without cracks and chips. You need to choose a saw canvas with a special wiring and a shallow pitch of teeth. High.Quality electric lines of well.Known manufacturers are equipped with a set of saws, each of which is designed to work with different building materials, including laminate.

Special files are produced for laminate

How to saw metal

The choice of files. For cutting metal surfaces, files with a small tooth are used. A tooth step 1. 2 mm. Visually, such a saw resembles a canvas of the hacksaw for metal and can be used for cutting other materials, in order to increase the cleanliness of the cut.

The frequency of the course. The speed of sawing must be set as low as possible.

The pendulum mechanism. The pendulum move is completely turned off.

The process of sawing. The workpiece tool must be moved slowly, without pressure. A sheet of tin must be firmly fixed in advance by placing it so that the cut line is as close as possible to the support.

If it is necessary to make a curved cut in thin tin, and it is not possible to arrange the workpiece so that the cut line is not possible, then it must be placed between two sheets of fiberboard or organ. All marking is applied to the upper sheet of fiberboard. This will prevent the formation of a burr.

It is also recommended to take small breaks in work and use additional cooling sources to avoid overheating of the file.

What to pay attention to when choosing a file for an electrolobian for cutting a laminate

To figure out which file for a jigsaw to cut a laminate, it is worth keeping in mind that this material is made of wood and its derivatives, which means a saw for an electrician is required “on wood”. In general, the jigsaw was originally created to work with wooden materials, so the main part of the files is calculated specifically for the tree.

All consumables can be conditionally divided by purpose, for which type of cut:

There are times when the speed of cutting comes to the forefront, and not its accuracy. To increase performance, there are files for quick cut with certain characteristics: the length of the canvas is at least 60 mm; Large teeth. Up to 6 mm; Divorce of a large size. Approximately 1 mm.

In cases where the speed is not important, but the quality of work: the accuracy and smoothness of the sawing, use files with other characteristics: teeth on average no more than 3 mm, divorce insignificant.

It is almost impossible to use files with a wide canvas in these cases. Here you need a special file with the following characteristics: the canvas is narrow. Not wider than 4 mm; Small teeth. Up to 2 mm; small length. Not more than 40 mm; The back side is scooped.

The main criteria for choosing a file: the shape of the teeth, width and thickness

To answer the question, which files are better to saw chipboard (tree) with an electrician, you need to keep in mind that most cutting canvases have the direction of the cloves in the direction of the jigsaw. For the maximum accuracy of the cut, the absence of chips and other things, files with the opposite direction of the teeth are used (working with a similar tool is an order of magnitude more difficult). If there were no one, then the product for the saw should be placed in the back side to itself.

Also, choosing a file, it is important to pay attention to whether it corresponds to a clamping device in an electrician.

There are also sets on sale, which are immediately equipped with different types of paintings. This is convenient, since in this case it is likely not required to buy a file for working with a laminate.

When purchasing consumables, you need to take into account a number of factors: the raw materials from which they are made, purpose, shape, dentition, step, etc. P. The use of individual saws will facilitate the cutting process, make it much more convenient and accurate.

There are the following main types of files suitable for cutting laminate:

File manufacturing material: metal with NSS marking. Teeth. In the upper direction. The pendulum course of the movement: the saw returns to the jigsaw and the material that is cut, immediately both up and go, as a result of which the material is pressed to the bottom of the jigsaw.

Quickly cuts the laminate, minimizing the formation of chips. Here it is necessary to take into account that you need to make markings from the back of the laminate board, that for beginners, it can initially cause certain difficulties. This is relatively non.Expensive type of saws, but will become frantically quickly.

T101BR: not very convenient to use. Teeth. In the lower direction. Strongly beats when the pendulum is moving. Can sometimes be used for accurate cutting out a complex circuit at the top of the laminate.

The length is about 75 cm, which does not affect sawing. Small teeth that contribute to even cutting.

It is used for cutting curved circuits, for example, when it is required to bypass home heating risers and so on. The speed of electrolobesis for curved cutting is recommended to use the average.

Are made of durable bimetall, as a result of which they have a long service life. Teeth do not have a certain direction and are located evenly.

Suitable for sawing the laminate both on the front and back. The cut is quite even. The speed is relatively good. For those who plan to lay a laminate themselves without having a special experience in this matter, this type of saw is best suited.

What to pay attention to when choosing a file for an electrolobian for cutting a laminate

To figure out which file for a jigsaw to cut a laminate, it is worth keeping in mind that this material is made of wood and its derivatives, which means a saw for an electrician is required “on wood”. In general, the jigsaw was originally created to work with wooden materials, so the main part of the files is calculated specifically for the tree.

All consumables can be conditionally divided by purpose, for which type of cut:

There are times when the speed of cutting comes to the forefront, and not its accuracy. To increase performance, there are files for quick cut with certain characteristics: the length of the canvas is at least 60 mm; Large teeth. Up to 6 mm; Divorce of a large size. Approximately 1 mm.

In cases where the speed is not important, but the quality of work: the accuracy and smoothness of the sawing, use files with other characteristics: teeth on average no more than 3 mm, divorce insignificant.

It is almost impossible to use files with a wide canvas in these cases. Here you need a special file with the following characteristics: the canvas is narrow. Not wider than 4 mm; Small teeth. Up to 2 mm; small length. Not more than 40 mm; The back side is scooped.

The main criteria for choosing a file: the shape of the teeth, width and thickness

To answer the question, which files are better to saw chipboard (tree) with an electrician, you need to keep in mind that most cutting canvases have the direction of the cloves in the direction of the jigsaw. For the maximum accuracy of the cut, the absence of chips and other things, files with the opposite direction of the teeth are used (working with a similar tool is an order of magnitude more difficult). If there were no one, then the product for the saw should be placed in the back side to itself.

Also, choosing a file, it is important to pay attention to whether it corresponds to a clamping device in an electrician.

There are also sets on sale, which are immediately equipped with different types of paintings. This is convenient, since in this case it is likely not required to buy a file for working with a laminate.

When purchasing consumables, you need to take into account a number of factors: the raw materials from which they are made, purpose, shape, dentition, step, etc. P. The use of individual saws will facilitate the cutting process, make it much more convenient and accurate.

There are the following main types of files suitable for cutting laminate:

File manufacturing material: metal with NSS marking. Teeth. In the upper direction. The pendulum course of the movement: the saw returns to the jigsaw and the material that is cut, immediately both up and go, as a result of which the material is pressed to the bottom of the jigsaw.

Quickly cuts the laminate, minimizing the formation of chips. Here it is necessary to take into account that you need to make markings from the back of the laminate board, that for beginners, it can initially cause certain difficulties. This is relatively non.Expensive type of saws, but will become frantically quickly.

T101BR: not very convenient to use. Teeth. In the lower direction. Strongly beats when the pendulum is moving. Can sometimes be used for accurate cutting out a complex circuit at the top of the laminate.

The length is about 75 cm, which does not affect sawing. Small teeth that contribute to even cutting.

It is used for cutting curved circuits, for example, when it is required to bypass home heating risers and so on. The speed of electrolobesis for curved cutting is recommended to use the average.

Are made of durable bimetall, as a result of which they have a long service life. Teeth do not have a certain direction and are located evenly.

Suitable for sawing the laminate both on the front and back. The cut is quite even. The speed is relatively good. For those who plan to lay a laminate themselves without having a special experience in this matter, this type of saw is best suited.

How to cut a laminate correctly: straight and curly cuts

Method 1. You can use a hacksaw or circular saw with a maximum number of teeth to avoid the appearance of chips. First make markings and mark the part of the board you are going to cut off. This can be done both with the help of chalk and a pencil. Erasing chalk then very simple. Well, then just cut the lamella along the marked line.

Method 2. You can also use an electrician. This option is several times simpler than the previous. Fasten the guide on the device, and then make it out the edge of the workpiece. In this case, the movement of the file will be even relative to the edge.

! You work with thin lamella? Be prepared for the appearance of chips on its front part. The fact is that in the first version the tool will move up. To prevent such an outcome, you can place the blank with the front side down. Another way out is the use of anti.Slip lifers.

How to cut a laminate on a curve correctly? For such work, only an electrician with a special canvas with very small teeth for laminated floors or even with a standard canvas is suitable. A special option is better, as it helps to cut up the pattern up and without chips.

• First prepare the desired paper or cardboard template. It is needed in order to calculate the cut and maintain the integrity of the board;
• Attach the template and circle the desired pattern;
• Cut the pattern and again attach the template to make sure of its accuracy;
• Now just circle the sample along the contour on the surface of the lamella;
• Make a drink. If you use the standard canvas, put the board with the pattern down and attach the template upside down. Keep the jigsaw only vertically. If you need to cut it with the front side, stick a strip of paint tape on the cut line so that you do not have chips when cutting. Then measure the lines on top of the tape on which you are going to saw the lamella. For this, a special canvas is used, intended for such floorings.

Sometimes the template must be applied several times so as to get a sample of the desired shape

How the surface of such a finish part will look like, depends on the special decorative layer

Laminated board.This is the most popular floor covering today, obtained as a result of pressing wood-fibrous slab (fiberboard). How the surface of such a finish part will look like, depends on the special decorative layer.

Often it repeats the drawing of wood, but sometimes it has a more complex ornament. The internal structure of the board includes 4 layers, which are “laminated” with a protective film on the outside, which gave the name the material itself.

The peculiarity of working with the laminate is, among other things, that the cut is carried out directly on the spot before laying. The question becomes quite reasonable: how to get an even cut and not spoil the part?

Laminate blade t101bif

This saw canvas is made of bimetallic (BIM), the most durable material, so it serves for a long time. The teeth are located evenly without a certain orientation.

T101BIF can be safely used both for the saw on the front of the laminate, and for the cut on the reverse part. It has a fairly even reza and good speed, slightly inferior in it T101B, when working with a jigsaw does not hit the workpiece.

For independently laying a laminate without great experience, I would recommend this particular type of file. On the manufacturer-we use Bosch or practice.

I vote in favor of a battery circular. The cut speed is much higher, it saws smoothly and efficiently, the disc is enough for aluminum for hundreds of meters. He also sawed a jigsaw with a pendulum course and without, with a variety of saws, but all this is a kindergarten compared to a disc saw. The only lobby cannot be replaced for figure cut. I use crowns for pipes for pipes. P.With. Author, correct the mistakes in the article, of which a bunch.

Sergey, thank you for the review. I do not use a battery saw, since the noise is higher, more dust. Crinoline cuts cannot be made either under the platband. When the first row was drunk, nor with an uneven wall of the last row. It is also inconvenient to use when cuts of angles. I don’t understand your appeal to “you”, we are not familiar with you. And did not indicate what errors should be fixed in the text. I ran once again in the text, I did not find spelling errors, perhaps there are errors in punctuation marks, but the text is complex and punctuation marks in some places can be arranged differently. I am inclined to the idea that the accusation of errors in the text is reduced in your look at the choice of a tool for work. Implying that I chose the instrument mistakenly.

Immediately by mistakes: phrases, such as “shorter length about 75 mm” somehow unlimitedly sound and the word length is written with one “n”. The word “however” is not isolated at the beginning of the sentence.E. It is written without a comma. I have a circular under my small diameter discs that will allow you to saw small bends. I don’t understand why to make drunk under the platband, the laminate is driven from below, a pair of direct cuts is enough. For drinking boards along the circular outside competition in general. I can’t remember from practice, so that somewhere it was necessary to saw with outlets and precisely a jigsaw, although also a saw for them, but if there is a saw very, very little, I use it to sample material. I won’t say sawdust that the thickness of the jigsaw and the saw of the saw is approximately the same, although they fly more from the saw (in any case, it is necessary to vacuum it from time to time). I make indentation from walls 1 cm and FOCUS on skirting boards 2 cm thick, which gives some right to error. And there is still a moment of savings. There is enough saw for one, maximum two rooms. The disk, of course, will be more expensive, but its resource is simply not comparable due to the use of carbide attacks and a large number of teeth.

Of course, you are talking more constructively now. But. The platband is of small thickness, about 6 mm, including a rounded. Therefore, you often have to do a curvilinear cut. I will say from my own experience, without a saw I can do it perfectly, but without a jigsaw. Then, the article was written to help for inexperienced masters. Therefore, the jigsaw will be more universal and less dangerous. As for the crowns for, I also use them for small diameter pipes, the pipes of large diameter are most often in sleeves with various influxes, so again. You can’t do without a jigsaw.

You can calmly cut the laminate with a jigsaw. Almost all the cuts are hidden with a plinth. It makes sense to work with a saw of the most decent volumes and in the presence of conditions for the operation of the saw (noise, dust). The article is normal. The author advises based on his own experience. To follow or not to follow this is decided by everyone on their own.

I did not like it (it was expressed in rude form, edited) these files, for 100k laminate already spent 7 pieces of this company, everyone will dull after a few cuts. Do not take this company

It is clear that figured cuts cannot be done with a circular and here you can not do without a jigsaw. But you will never achieve the jigsaw of such an even and pure cut as the circular saw will give. Especially if you cut into 2 grooves: the first 1-1.5 mm on the front side, the second is already for the entire thickness. And she wins in speed, even taking into account double runs.

If we are talking about laying a laminate for readers, then I do not think that it is worth picking up a circular saw. She is much noisier, there is much more dust from her and she is a dangerous tool, unlike a jigsaw. The even cut that you are talking about is needed only to adjoin the edges of the laminate without thresholds. I know how to cut enough evenly cuts in order to hand over the work of adjusting the laminate to the tile, for example. And for me, the circular saw is no faster tool. But in the description of the manufacturers of the laminate, an adjacent of 2-3 mm from the walls or other fixed parts, the same tiles is not allowed. Therefore, cuts are overlapped by thresholds. This should be according to technology. You know this very well, I don’t understand why you need this dispute to argue or teach? Make your site by electrician.

Than and how to cut a laminate?

The choice of flooring largely determines the quality and price. In this regard, the most acceptable ratio has a laminate. The material owes its popularity not only practicality, but also the simplicity of laying. In the presence of the tool, the installation of the flooring is capable of performing each. Accordingly the question arises. How to cut a laminate?

To lay the flooring, the material must be taken 10-15% more than the area of ​​the room. The panels will need to be not only connected, but also to cut. To adjust the dimensions, use a manual or electric tool. When used at home, it should:

The last characteristic when choosing a method for many repair lovers is a key. But its importance is somewhat exaggerated. The presence of chips up to 5 millimeters will hide the baseboard.

Both experts and home.Made master for cutting laminate use:

Neo.Class features when choosing files

Step (t) is the distance between the tops of the teeth. In some countries, the step is indicated by TPI (Teeeth Per Inch). It is measured by the number of teeth per inch (for example, tpi = 7, t.E. 7 teeth per inch). With transverse sawing of wood, it is convenient to use a saw with a large tooth T = 3.5-6.5 mm (tpi = 7-3.5), with ordinary carpentry-with an average tooth T = 3-3.5 mm (tpi = 9.7), with a responsible sawing-with a small tooth t = 2-3 mm (tpi = 13-9). In this case, it is necessary to take into account the thickness of the sawed material.

It is easier to cut a jigsaw when 5-8 teeth of the file are involved, when cutting. If this rule is not observed, the canvas will vibrate during operation, and the cut line will turn out to be a curve and a torn.

The stability of the saw canvas during the cut in a straight line depends on the thickness of the file. For sawing thick blanks, it is better to use disc saws.

How to cut properly and evenly

The material is sawn on preliminary marking (lines) or exhibited side cutting. Sometimes it is conveniently with clamps to clamp the guiding corner on the workpiece and move the edge of the Electrician platform along it. In this case, it is calculated and measured where the file will take place, not the edge of the platform.

The main question is which side to cut the laminate with a jigsaw, put the facing side or up. There is no unequivocal precise answer to this question. It all depends on the type of file and material. To understand which side to put in each case, you should figure out why this is important and why it happens differently.

If the laminate lies with the front side (laminate) down, the saw passes above the void. The cladding does not hold anything, and the teeth can pull the particles of the material down into the void along with the cladding.

If the cladding looks up, when sawing the teeth of the saw, they strive to tighten its particles down, but they rest against the material itself, and not on the void and therefore the laminate is held, less breaks.

It seems that there is nothing to argue about, cladding. Up. But in two cases not so.

Cut the laminate with a circular saw

First of all, it is recommended to use a circular saw only for those who have experience in interacting with this tool. Otherwise, you will have to make maximum efforts to achieve the optimal result.

How to saw correctly. The saw should be equipped with a disk that serves for metal cutting. The board marked and prepared for the saw is placed on a flat surface. Laminated film is necessarily located on top. To obtain a high.Quality and flat surface of the cut of the circular saw, you need to move smoothly and slowly.

Circular saw/machine or circular

The cheapest circular, meaning a saw, costs from 40. Buying it specifically for a cut of laminate when laying it is pointless. And drag a huge machine into an apartment is also not an option. If you are a happy owner of this tool, you can safely cut a laminate. To do this, use a metal disk. The newcomer will have to learn how to use the circular. This is not safe, even experienced craftsmen sometimes get injuries.

Features of the use of circular saw:

• Mark and cut on the front side;
• Reliably fix the workpiece on a flat surface upwards. It is to fix it, and not so that one holds, and the other saws;
• If you have a circular machine. Marking and cut also on the side with a pattern;
• In the case of using the machine, the laminate board is not fixed. She is neatly conducted to disk. Be sure to use glasses so that large sawdust does not get into the eye.

Using a special tool

For cutting a laminated board in addition to a jigsaw, grinder and hacksaw you can use a special tool, or rather a machine. At the first glance at the equipment, we can say that it is very similar to the guillotine that is used to cut paper. The machine is made of the support on which the lamella, blades and pens are located. After clicking on the handle, the blade drops to the lamella. The cut is even and beautiful.

The machine works silently, leaving no construction debris and dust behind. The material does not form defects in time.

You can, of course, purchase such a machine. But, if you do not professionally deal with repairs, then it will simply gather dust in the corner almost all the time.

Laminate cutter is used exclusively for transverse cutting of the lamella. If you need to cut the laminate bar along, then you can’t do without a grinder, jigsaw or hacksaw.

Not always the incision is ideal. However, it should be remembered that the baseboard will be laid on top of the laminated board. He will close an uneven cut. If a crack has formed during the cutting of the lamella, then do not worry. A similar defect can be corrected using a special pasta.

We figured out how to cut a laminate. But, in the end, I would like to note that when using an electric jigsaw, grinder or hacksaw, construction garbage in the form of sawdust will form during operation during operation. Therefore, it is advisable to preliminarily cover the floor with paper, film or fabric. And even better to work not in the room in which styling is performed, but in the neighboring. After all, lay a decorative flooring on a clean surface.

After the cut of the laminate bar, you need to wipe the place with a wet rag. This is done in order to get rid of the dust that was formed in the process of sawing.