Is It Possible To Tighten The Screws With A Drill
How to replace a screwdriver with a conventional drill: 3 useful tips
Is it possible to replace a screwdriver with a drill and how do they differ at all? This, as well as security issues during such experiments, we recommend that you consider with us.
How to replace a screwdriver with a conventional drill: 3 useful tips
Ingenuity helps to get out of difficult situations associated with a lack of tools. A drill can replace a screwdriver. Knowledge and adherence to safety rules is the first condition for working with this tool. Therefore, to the question “is it possible to make a screwdriver from a drill?” there will be a positive answer. We will talk about the intricacies and secrets of the process in the article.
What is the best drill or screwdriver?
The principle of operation of a drill and a screwdriver is similar. The devices differ from each other in that the first tool is equipped with a limiter for the rotation of the chuck when the resistance reaches its highest point. If you tighten the screws with a drill, it is important not to miss this moment. Then the surface will not be damaged, and the corners of the bolt will not be smoothed (this will significantly reduce the adhesion of the surfaces).
The drill is designed for drilling holes, and the screwdriver is for screwing in self-tapping screws, but they can be replaced with one another. There are drill bits that turn it into a screwdriver. Attachments are:
- Simple;
- With a limiter.
The stop does not allow the self-tapping screw to enter too deeply into the surface. This effect is provided by a restrictive rim present on the nozzle.
It is impossible to say which is preferable. A drill or a screwdriver. Since the two tools perform different functions.
Using a drill as a screwdriver
In the absence of attachments (and the ability to purchase them), it is recommended to use the following strategy. There is no splitting sleeve in the drill, which leads to unpleasant consequences. Using this tool as a screwdriver without the necessary attachment can be fraught with:
- Breakage of the screw head;
- Broken bit;
- Combustion of the drill.
Tighten the screws or bolts with a drill not to the bitter end, but leave at least half a centimeter outside the surface. It is generally optimal to screw the rest of the screw into the surface by hand. Yes, you will waste time, but keep the drill safe.
Read also: How to choose a drill?
The drill can also be used for its intended purpose (drilling surfaces). Drill a hole in the surface of the material to be used, then carefully screw in the screw. This will be much faster than screwing in the screw by hand. In addition, you will definitely not damage the surface, creating a more delicate mount without delamination of the material. Useful if you need to drive a screw into the wood.
Is it possible to tighten screws with a drill? You can, but do not lose sight of one feature of the screwdriver. This is a kind of symbiosis of a Phillips screwdriver and a drill. A tool with speed control is especially appropriate. The slower it runs, the less the risk of failure. With skill and a good reaction, furniture assembly (and other construction work) will go even faster with a drill.
Based on the above information, it can be concluded that there are three ways to get a high-quality result when using a drill instead of a screwdriver:
1. Use special nozzles with a limiting rim;
2. Do not screw the screws into the surface completely, making the last few turns by hand;
3. Pre-drill the surface and then screw the bolts into the hole.
Just always be careful and follow safety precautions when working with tools.
See by topic: How to use a drill instead of a screwdriver?
Is it possible to tighten self-tapping screws with a drill
Of course you can. On sale there are attachments for drills and screwdrivers for self-tapping screws.
In general, it is possible, but it’s like hammering a nail into a wall with a brick, a hammer, and it’s more convenient and safer.
Drill and screwdriver are different tools.
Many people mistakenly think that a screwdriver is a battery, and the drill works from the mains, this is not the case, for example, I have a mains screwdriver.
The fundamental difference lies elsewhere.
The screwdriver has such a function as “power regulator”.
That is, when the screw (or self-tapping screw) is fully tightened, the rotation of the cartridge stops, a characteristic sound (crackling) is heard.
The drill will rotate endlessly until you remove your finger from the button.
It is enough to skip this moment a little and you can simply dislocate your hands.
The “default” speed of the drill is higher than that of the screwdriver.
That is, at the finish line you can lick off the edges of the self-tapping screw.
The chuck of the drill, unlike the screwdriver, does not stop instantly, in addition to injury to the hands, the damaged material, for example, the self-tapping screw entered the gypsum board deeper than necessary and crushed it.
You can tighten it, but observing increased security measures.
Of course you can. On sale there are attachments for drills and screwdrivers for self-tapping screws.
In general, it is possible, but it’s like hammering a nail into a wall with a brick, a hammer, and it’s more convenient and safer.
Drill and screwdriver are different tools.
Many people mistakenly think that a screwdriver is a battery, and the drill works from the mains, this is not the case, for example, I have a mains screwdriver.
The fundamental difference lies elsewhere.
The screwdriver has such a function as “power regulator”.
That is, when the screw (or self-tapping screw) is fully tightened, the rotation of the cartridge stops, a characteristic sound (crackling) is heard.
The drill will rotate endlessly until you remove your finger from the button.
It is enough to skip this moment a little and you can simply dislocate your hands.
The “default” speed of the drill is higher than that of the screwdriver.
That is, at the finish line you can lick off the edges of the self-tapping screw.
The chuck of the drill, unlike the screwdriver, does not stop instantly, in addition to injury to the hands, the damaged material, for example, the self-tapping screw entered the gypsum board deeper than necessary and crushed it.
You can tighten it, but observing increased security measures.
Ingenuity helps to get out of difficult situations associated with a lack of tools. A drill can replace a screwdriver. Knowledge and adherence to safety rules is the first condition for working with this tool. Therefore, to the question “is it possible to make a screwdriver from a drill?” there will be a positive answer. We will talk about the intricacies and secrets of the process in the article.
What is the best drill or screwdriver?
The principle of operation of a drill and a screwdriver is similar. The devices differ from each other in that the first tool is equipped with a limiter for the rotation of the chuck when the resistance reaches its highest point. If you tighten the screws with a drill, it is important not to miss this moment. Then the surface will not be damaged, and the corners of the bolt will not be smoothed out (this will significantly reduce the adhesion of surfaces).
The drill is designed for drilling holes, and the screwdriver is for screwing in self-tapping screws, but they can be replaced with one another. There are drill bits that turn it into a screwdriver. Attachments are:
The stop does not allow the self-tapping screw to enter too deeply into the surface. This effect is provided by a restrictive rim present on the nozzle.
It is impossible to say which is preferable. A drill or a screwdriver. Since the two tools perform different functions.
Using a drill as a screwdriver
In the absence of attachments (and the ability to purchase them), it is recommended to use the following strategy. There is no splitting sleeve in the drill, which leads to unpleasant consequences. Using this tool as a screwdriver without the necessary attachment can be fraught with:
- Breakage of the screw head;
- Broken bit;
- Combustion of the drill.
Tighten the screws or bolts with a drill not to the bitter end, but leave at least half a centimeter outside the surface. It is generally optimal to screw the rest of the screw into the surface by hand. Yes, you will waste time, but keep the drill safe.
Read also: How to choose a drill?
The drill can also be used for its intended purpose (drilling surfaces). Drill a hole in the surface of the material to be used, then carefully screw in the screw. This will be much faster than screwing in the screw by hand. In addition, you will definitely not damage the surface, creating a more delicate mount without delamination of the material. Useful if you need to drive a screw into the wood.
Is it possible to tighten screws with a drill? You can, but do not lose sight of one feature of the screwdriver. This is a kind of symbiosis of a Phillips screwdriver and a drill. A tool with speed control is especially appropriate. The slower it runs, the less the risk of failure. With skill and a good reaction, furniture assembly (and other construction work) will go even faster with a drill.
Based on the above information, it can be concluded that there are three ways to get a high-quality result when using a drill instead of a screwdriver:
1. Use special nozzles with a limiting rim;
2. Do not screw the screws into the surface completely, making the last few turns by hand;
3. Pre-drill the surface and then screw the bolts into the hole.
Just always be careful and follow safety precautions when working with tools.
See by topic: How to use a drill instead of a screwdriver?
Instruments
The thing is that home craftsmen often do not know how to screw in a self-tapping screw correctly and how to choose it correctly.
How to screw screws into different materials?
Many men, not knowing how to screw a self-tapping screw into concrete, spoil a sufficient number of purchased parts. In fact, everything is quite simple: self-tapping screws are “integrated” into concrete with the help of dowels. Durable plastic “tubes”. First, a hole is made in the material, a dowel is installed there, which “receives” the fastener.
Drilling holes in concrete should be done exclusively with a hammer drill. Even a hammer drill may not withstand, let alone a conventional one. Self-tapping screws are suitable for both wood and universal.
Brick, ceramic tile, screed
Self-tapping screws are screwed into these environments in the same way as into concrete. The only thing is, for working with tiles, it is better to take an ordinary drill, since it can crack from the excessive power of the hammer drill.
Copper, bronze, aluminum
Measure the shank diameter of the fastener excluding threads. This manipulation must be performed with a caliper. Install the pointed jaws perpendicular to the self-tapping screw and clamp the product so that they completely penetrate the thread groove; determine the diameter. With a drill with a diameter of one and a half millimeters smaller than the obtained value, make a hole in the material. Screw the screw into the hole. And the job is done. Use parts with universal threads.
The hole in the material must be equal to or slightly larger than the unthreaded bar diameter. Self-tapping screws will not be able to cope with a number of hard metals. In particular, it is almost impossible to screw these fasteners into cast iron.
Not every plastic is ready to accept a self-tapping screw, so it will not be superfluous to make sure before starting work that the material exactly fits. The technology for screwing a self-tapping screw into plastic is the same as for soft metals. Copper, aluminum, bronze. Recommended products are wood carvings.
Wood, fiberboard and chipboard
Don’t know how to screw a self-tapping screw into the board? Believe me, nothing is easier. The basic rule is to use only wood screws. For hard wood, thin boards, chipboard, fiberboard, pre-drilling a hole for the product is mandatory, since there is a risk of splitting the material with a self-tapping screw. For thick softwood boards, this manipulation can be dispensed with.
If you are working:
- With hard wood. Choose a drill with a diameter equal to the diameter of the self-tapping rod (naturally, no thread);
- With fiberboard. 1 millimeter less;
- With chipboard or softwood. 2-3 millimeters less.
Mark points on the sheet with a pencil. The optimal pitch between the screws is up to 70 centimeters, depending on the expected loads on the structure. If you are using a screwdriver, you can start screwing the product at maximum speed. After the self-tapping screw enters the surface by ½ it is recommended to gradually reduce the speed to the minimum. When tightening with an ordinary screwdriver, all movements should be smooth. It is very important to tighten the self-tapping screw correctly. Ideally, it should be 1 millimeter below the level of the cardboard, not plaster! This will ensure the maximum strength of the future structure. If you suddenly did not follow the technology and broke through the cardboard, the “ill-fated” place needs to be putty, and a new fastener should be placed at a distance of 5-9 centimeters from it.
The type of self-tapping screws for drywall must be selected depending on the material used in the construction of the sheathing. For a metal frame, universal or metal self-tapping screws are required, for wooden lathing. Wood products.
Self-tapping tools
Fasteners can have caps of various sizes and recesses in them of various shapes and sizes. Therefore, before you screw in the self-tapping screw, make sure that you have a screwdriver or screwdriver with a suitable attachment in your arsenal. In general, it is better to have nozzles for the corresponding tools, as they say, to the maximum. Plus, they should be replaced regularly, since the wear of the devices during operation cannot be avoided.
If your plans include screwing one or two self-tapping screws into an unstable surface, then you can work with a screwdriver. If more, you cannot do without a screwdriver. Tightening the fasteners with a screwdriver is not as easy as it might seem at first glance, and requires some skill. A screwdriver will do everything quickly and efficiently.
Table of contents
- Types of self-tapping screws
- Self-tapping tools
- General screw-in technology
- How to screw screws into different materials?
- How to properly tighten the unscrewed self-tapping screw?
Types of self-tapping screws
There are two main types of self-tapping screws used for self-repair. For wood and universal. Their main difference is in the thread pitch. “screws” for wood are characterized by a large pitch (less frequent threading).
There is a misconception that universal parts are just as good for wood, plywood and chipboard as specialized ones. No, of course, it will not be difficult to screw them into these materials, but how well they will stay there is a big question. The fact is that the “raw material” into which the self-tapping screw is “immersed” must reliably lie in the grooves of the thread, and the structure of the wood will not allow it to fit qualitatively in the narrow “grooves” of the universal self-tapping screw.
General screw-in technology
Use an awl to make a small indentation in the place reserved for the screw. Install the product “on position”. Use careful but firm movements to rotate the part until it is deeply embedded and anchored in the material. Then the force can be increased. Towards the end of the “process”, the speed must be reduced again. So as not to damage the screw.
Is it possible to drill a hole in a concrete bearing or brick wall of a panel house with a conventional drill, puncher or screwdriver without dust, how to do it
When making repairs in an apartment or house, the question of drilling a wall always arises. Different tools can be used depending on the purpose of the hole and the material from which the surface is made.
There are nuances when working with each tool, especially when drilling a wall. How to make the right hole correctly, and what recommendations to follow?
- Drilling holes in the wall correctly: general rules and recommendations than drilling
- Tools for work
- Drill
- Puncher
- Screwdriver
- Which attachments to choose
- Is it possible to do without a drill and punch
- How to drill without dust: the options are better
- How to drill holes in a brick wall: the choice of tools and attachments
- How to drill a load-bearing wall in a panel house with a perforator
- How to properly drill a reinforced concrete pipe with an impact drill
- How to make a hole in a concrete wall with a drill
- How to make a hole in a concrete wall in an apartment with a drill
- Work rules: tips
- How to fix a large drilled wall
- Useful
Work rules: tips
When working with tools, you must follow the safety rules and general recommendations:
- 1) When performing work, protect the respiratory system, dust is harmful.
- 2) If you are working outside, then you need to put fences 2.5 meters.
- 3) When working at a height of more than 1.5 meters, use a solid foundation. A scaffold or a goat.
- 4) When working with a tool, the revolutions must be turned on smoothly, and in no case should it be turned off when it is in the body of the wall.
- 5) When drilling through plaster, you must carefully study the communications plan so as not to hurt anything.
- 6) It is strictly forbidden to drill through the decorative coating.
- 7) Choose the right drills for each surface.
- Wet the drill with water so that it does not overheat.
How to properly drill a reinforced concrete pipe with an impact drill
When using a percussion drill for reinforced concrete, you need to use the “hammer drill” mode and winder drills. At first, the hole is made with a smaller volume, then a larger one. The drill needs to be cooled periodically.
Important! When working with concrete, do not hit the reinforcement, otherwise the drill will break. Using a special device, you can check where it is located.
Puncher
The puncher is a versatile tool. It can be used to make a hole in a wall made of wood, tiles and concrete.
The tool has several functions. Drilling, hammer drilling and hammering mode. To make a hole, you need to select the desired drill depending on the surface and perform the work by selecting the mode.
Drill
The tool is suitable when you need to make multiple holes. You can use a conventional drill. When immersing a victorious drill into the body of the wall, sometimes it is necessary to break the concrete with a punch that matches the diameter of the hole. This is necessary when the drill starts to get stuck in the surface, bumping into too dense areas. The process is quite laborious.
For greater efficiency, you can use universal drills that are diamond-coated. They are installed only on a conventional drill or on a tool where the vibration function is disabled.
For large-scale work, an impact drill and drills with victorious tips are used. They are designed for holes up to 12 mm. The drill is suitable for working with metal, concrete.
How to drill without dust: the options are better
Construction work is always accompanied by dust and debris, but using some guidelines and tips, it can be significantly reduced:
- The hammer drill leaves little dust during operation so that it does not scatter around the room at the same time use a construction vacuum cleaner. Some brands of tools have a built-in vacuum cleaner, which makes the task easier;
- Using a drill, it is best to either make a jig on the end or a bag, or make an envelope under the hole so that debris falls into it.
Nozzles
During operation, the nozzles wear out, and they need to be periodically updated, otherwise it will be painfully difficult to carry out the process of tightening the screw. When choosing attachments, be sure to pay attention to what material they are made of. It is better to purchase models from special tool steels, which are added with strengthening additives during production.
There are a lot of manufacturers of nozzles, so only with experience will you understand which one is most suitable for you. Most attachments only have a one working day reserve if you need to use them thoroughly and continuously. Once you have found a suitable option, purchase several sets from the same batch in advance. When purchasing a set for the first time, be sure to check all attachments for their match to the head of your self-tapping screw. One of them will seem to you the most suitable, so do not dwell on the first one you try on.
Screws can be screwed in with a screwdriver with an electric drive or battery, or with a screwdriver. With one-time work, it is quite possible to do with a screwdriver with nozzles, but if you need to constantly screw in the screws, a screwdriver is unlikely to suit you. Even a few screws are easier to tighten with a screwdriver. Screwing in with a screwdriver is a complicated operation. It will take skill and effort. Having a good screwdriver, you can not be afraid of any screws and screw them easily, simply and quickly, and exactly where you planned.
Choosing a screwdriver
After choosing a screwdriver, and not a screwdriver, be sure to check whether it is comfortable to hold it in your hand. All screwdrivers have handles of different shapes and sizes. It is best to choose a handle made of wood or rubber, and quite thick. Never use varnished wood. Plastic is a bad option for a screwdriver handle because it slips in your hand. Currently, soft plastics, similar in properties to rubber, have begun to appear on the market. In any case, be sure to hold it in your hand, because it should be convenient for you to work with it.
How do we tighten the screw?
Among the self-tapping screws, there are two main types, which are determined by the thread pitch:
- Self-tapping screws for wood
- Self-tapping screws are universal.
The former are characterized by a larger thread pitch. Thread turns during its manufacture are applied less often. Some people mistakenly believe that universal screws are suitable for working with wood, plywood, chipboard, fiberboard. This is only partially permissible. Screw a universal self-tapping screw or a screw into a wooden surface, which is essentially the same thing, of course, you can, but it will hold on there worse than a specialized one, i.E. Designed for wood. The material where the self-tapping screw is screwed must fit securely into the thread groove. The toughness of the wood will not reliably lie in the groove of the universal self-tapping screw, since this groove is very narrow. In this regard, it is still recommended to use specialized types of wood screws for all wooden surfaces.
Self-tapping screws are available in a wide variety of cap sizes. In addition, the geometry of the screwdriver cavity is also different. Self-tapping screws with a recess for:
- Phillips screwdriver
- Flat screwdriver,
- Special screwdriver,
- Keys.
Cruciform grooves also vary in size and shape. In connection with such a rich assortment, you have to have not just a screwdriver, but a screwdriver or screwdriver with special replaceable nozzles, which allows you to screw in screws of any kind and type without any problems. It is desirable to have the maximum number of such nozzles.
Choosing a screwdriver
In the event that you decide to choose a screwdriver, decide whether it will be a battery model or not. Cheap and standard cordless screwdrivers are hardly suitable for intensive work. They are not designed for long periods of inactivity and will require constant manual control from you to charge the battery to avoid overcharging. Since it is rarely possible to keep track of the charging of the battery, it usually takes about 30 to 50 cycles.
If you intend to work with a cordless screwdriver all the time, buy a professional cordless model, or choose a non-cordless tool that is powered from the mains. In fact, the latter is an ordinary drill, but equipped with a number of additional functions. Such a tool on sale can be found under the name “drill” and under the name “screwdriver”.
Most importantly, make sure that the model you choose has a gearbox. It is designed to adjust the speed of rotation that is required during operation and depends on how much the trigger is pulled. Minimum speed indicator. From 0.5 rev / sec. Also, the selected model should have a reverse, since sometimes it is necessary to turn out the screws when dismantling.