Lawn mowing trimmer for grass how to disassemble the coil. What can be used instead of fishing line

Repair of a trimmer coil for the grass with your own hands: how to remove, disassemble, change a fishing line for a trimmer, assemble and install back

If the fishing line for the trimmer is not lengthened by a light blow of the trimmer button for grass on the ground, the prerequisites for this usually the following.

Option 1. snack, t.E. Clamping cord between turns. This problem usually occurs if the user wraps a fishing line for a trimmer to a coil unevenly, crossing the windings or wrapping it without tension. In the latter case, when the mower rotates at high speeds under the influence of centrifugal force, the cord begins to drag on, under the influence of which the interspersonal clamp of the braid fishing line may occur. To eliminate obstacles, you need to disassemble the coil on the trimmer and correctly rewind the cord, in other words, even rotates with good tension.

Option 2.4. very short ends stick out of the head. When hitting the ground, the rod may not fall out if its ends protruding from the head are not long (short). Then centrifugal force is not enough to stretch the fishing line for the trimmer. Therefore, it is necessary to hang the unit (turn off the engine in another way, disconnect the electric trimmer for grass from the network) and pull the fishing line for a trimmer manually, after pressing the button.

Option 3. Fishing line for a trimmer to be sealed inside a mower. This makes the coil stop and do not even rotate when you press the button. This is mainly happening for several reasons: low quality of the cord, overheating of the coil during prolonged operation of the machine and the effect of a mowing fishing line on hard objects.

First, the cord of third.party manufacturers that you like is made of low.quality and fusible materials that do not withstand mechanical and thermal loads. Therefore, it is necessary to give preference to “branded” fishing.
If you have a fishing line for a trimmer of an unknown owner, and it is often soldered during operation, then, of course, follow the example of some users who, after filling the cord in the coil, moisten it or silicone lubricant (from a spray can) or mineral oil). This procedure significantly reduces the possibility of soldering turns of the mowing fishing line.
A fishing line for a trimmer can also be soldered if during a mowing it falls into a solid object (stone, fence, dry branch, etc. D.). During this time, it stretches a little and stretches to the head at high speed. The cord heats up from friction, and its coils stick together. The only thing that will be done to eliminate this problem is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

There are situations when a user of a trimmer for grass notices very quick fishing line consumption. Here he never clicked the button button to lengthen the fishing line for the trimmer. A prerequisite for spontaneous lengthening of the fishing line by cutting a special knife on the machine body is a lack of spring in a mowing head. Often beginner users of mowers, trying to load a fishing line for a trimmer into a coil, forget to install a compressed spring in the head, in other words, they completely lose it when opening the lid, and then they do not even suspect its existence.

The trimmer fishing line also expands without using the button if the spring is weakened. If the spring check confirmed this fact, then you need to insert several goals under it to increase the characteristics of the pressing.

The owners of the trimmers, mostly beginners, in confusion, next to the panic, when the coil has to change the cutting tool or fishing line for the trimmer. Often, when trying to unscrew the lawn mowing head, users simply make it unsuitable for use, not suspecting that it is unscrewed in the opposite direction to prevent this if you need to change the tool, we recommend that you join the step.by.step annotation below.

Before pouring the rod into the coil, turn off the engine bureau, as it is also called, de.energize the electric trimmer for the grass to avoid injuries that occur when a cutting tool is accidentally rotated.
Unscrew the attached nozzle of the transfer shaft. To do this, it is necessary to fix the shaft by leaving the opening on the puck and inserting an iron bar there or a screwdriver there.
Unscrew the nozzle. You should know that the thread on the shaft remains. Therefore, turn the coil of the trimmer for the grass to the right, in other words, clockwise.
Disassemble the mowing head. In most cases, the main cover is attached on the clips. To remove it, you will need to lower these clamps onto the case, squeezing the edges of the lid. If you have a pass, if your trimmer for grass has an automatic mower with a button below, then the nozzle should be disassembled carefully, since there is a chance of a spring loss, which sometimes flies away when removing the lid. ,
Cut the required amount of fishing. Usually its length is 5 meters. Use the cord of the same diameter that is indicated in the note to the tool. It is not recommended to exceed the largest diameter of the mowing fishing line, as this will increase the load on the engine and increase gas mileage.
Find the middle of a piece of cord, folding it in half. You will get a loop.
The coils are cut special grooves inside (there are holes). Insert the loop of the fishing line into this groove.
Wind a fishing line for a trimmer to a coil, turning it counterclockwise. The cord must be filled very evenly, the turns you need to put it in a non.overlap and with good tension. After the winding is completed, leave the free ends of the fishing line about 20 cm long and fix them in grooves on the sides of the coil.
Collect the mowing head. Do not forget to completely assemble the nozzle spring and washer (if available). Insert the coil into the housing and pass the ends of the cord through the holes or eyes.
Put on the lid and fix it with latches.
Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Turn the coil of the trimmer for the grass to the left (counterclockwise).

Problems with fishing line

The users of trimmers, both gasoline and electronic, from time to time there are difficulties with the cord. The “advanced” owners of the braids without effort are controlled in the difficulties that have appeared, understanding why this is happening, and for beginners it is an inconsistent that does not have the best clarification. But in fact, everything is solved quite easily. The most frequent obstacles that happen to the fishing line, subsequent.

The cord is not served, the coil does not spin

Automatic or automatic head should serve a fishing line for a trimmer without stopping the unit. But if it does not come out, then the prerequisites can be subsequent:

The fishing line for a trimmer in a coil is incorrectly wound, which is why the latter does not revolve;
The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be neat carefully, a turn to the turns, without distortions);
Very short.term ends of the thread come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the fishing line is not served for the trimmer (it is recommended to always adjust the length of the cord before starting the unit, pulling it down a little);
The fishing line for the trimmer is sticking together (it will be considered further).

a fishing line for a trimmer flies out

The prerequisite that the cord after starting the unit is unwound, can also be a weakening of the spring of the head of the head. In addition, there are times when a mowing head

, and the spring installed in it disappears. Inexperienced users do not notice the absence of a spring and collect this knot without it. Therefore, the cord does not hold, and under the influence of centrifugal force flies out.

Option

To remove the head of the trimmer for the grass, it will need to have a complete disassembly.

To remove the lid covering the inside of the head, you need to press on the latches (latches) located on 2 of its sides.
Removing the lid, you will see the rogue that needs to be removed from the body. In some coils under the bobbin, a spring is installed, which must be carefully removed so as not to lose it in the grass.
Removing the bobbin, in the center of the case you will see a screw with a slot under a cross.shaped or flat screwdriver. It is possible that there may be a bolt under the hexagon or nozzle “Asterisk”.
With the help of a screwdriver, choosing the desired bat (nozzle), you need to unscrew the bolt (counterclockwise).
After extracting the fasteners, take up the part of the part and, shaking it in different directions, remove it from the gear shaft.

Large cord consumption

In the main thing, the cord is rapidly ending, if you often knock on the ground with an automatic head or press it very down very much. The coil unlock occurs, and the fishing line for the trimmer, lengthening, is cut off by a knife. Another reason that the cord is rapidly ending is the incorrect operation of the device with an automatic head: the user with kosbe often drops the engine speed. But as we recall, the automatic head is arranged so that exactly with each reduction in the revolution the new portion of the fishing line is supplied, therefore it is rapidly consumed.

The thread does not hold

It happens that the thread is unwound if the spring weakened in an automatic head. The fishing line for the trimmer is put forward and cut off by the knife installed on the casing all the time, which increases its consumption. To check this, remove the casing and turn on the unit. If the fishing line for the trimmer “climbed”, then you will need to replace the spring.

Option

In this version, the head is twisted onto the gear shaft. To remove it, It will be needed

Fix this shaft. To do this, in similar trimmers, for example, in Huter and Champion devices, a hole is foreseen, through which you can stick either a narrow screwdriver or an iron rug.

So, to remove the bobbin, take 2 ordinary steps.

Shine the screwdriver in the hole and stall the shaft.
Take the head of the head and start twist it clockwise. It should be twisted in this direction for the reason that the thread cut on the shaft is left.

https: // yotools.ru/trimmeri/kak-namotat-lesku-na-katushku-trimmera-klyuchevye-momenty.html https: // obinstrumente.RU/Sadovyj-Instrument/Kak-Pomenyat-Slesku-V-Trimmera.html https: // tehnika.Expert/Dlya-Sada/Trimmer/Kak-Pravilno-Namotat-Slesku.HTML

How to choose a fishing line for a trimmer. length, diameter, restrictions

For any electric or gasoline trimmer for grass, you can use fishing lines of different manufacturers. However, the best option is the consumable of the same brand as the tool. It is believed that in this case it will benefit the durability of work and even reduce the consumption.

ВАЖНО ЗАПОМНИТЬ! Нельзя использовать для триммера для травы рыболовную леску для триммера или металлические тросики. Такая замена не эффективна и опасна. Трос может травмировать не только самого косильщика, но и окружающих.

lawn, mowing, trimmer, grass, disassemble, coil

As for the length, it is worth counting on the estimated frequency of using a trimmer for grass. The more often, the more it is worth stocking up. Information about the possible diameter of the fishing line is found on the body of the coil for a trimmer for grass. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose a suitable option, taking into account the features of the processed territory. The larger the diameter, the easier it is to mow hard grass.

How to remove a coil from a trimmer for grass and extract a fishing line for a trimmer

Initially, before filling the fishing line for the trimmer to the coil of the trimmer for the grass, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum. The heads are of different types (depending on the manufacturers), however, the principle of replacing the fishing line on the coil has the same. First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a fishing line from it.

It is interesting!The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station. Instructions on how to promote a hand head on a trimmer, has the following look:

mowing

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

Knowing how to disassemble the drum, you should continue to clarify the process of replacing a trimmer fishing line for grass. Below the video shows a detailed process how to open a trimmer coil for grass and disassemble it.

Removing and disassembling the coil

The braid trimmer head consists of a casing, a spring (not in every model), bobbins with a cord, cover. Before proceeding to disassemble the coil of the electric unit, be sure to turn off the trimmer for the grass from the network. The disassembly method depends on the mounting of the mowing head. First option:

To remove the lid covering the inside of the head, click on the latches (latches), which are located on its two sides.
Remove the lid under which you will see the spool. remove it from the body. Some trimmers have a spring under the bobbin coils, which should also be carefully pulled out.
Removing the bobbin, you will see the screw in the center of the case. Unscrew it with a screwdriver.
After extracting the fasteners, take the case body and, shaking it in different directions, remove the gearbox from the shaft.

In the second version, the head of the trimmer for the grass is twisted onto the shaft of the gearbox. To remove it, you need to fix the shaft. To do this, in such devices there is a hole through which a thin screwdriver or metal rod is inserted. Brief Instruction:

Insert a screwdriver into a special hole, then stall the shaft.
Get the body of the head and start twist it. This should be done clockwise, t. to. Larva shaft thread.

Fishing winding

Tramoring the fishing line in a trimmer coil for grass is a relatively simple procedure, provided that you adhere to a certain algorithm of action. When you need to determine how many meters of consumables are enough, wind it on the bobbin so that the skein does not exceed the diameter of the sides. Having decided on the length of the cord, follow the following instructions:

Fold the consumable material so that one end of the fishing line is 10-15 cm longer than the other.
You need to start charging with the central side, which divides the backpack of the trimmer for the grass into 2 parts. Find a groove where the cord should be inserted. The latter is bent twice.
Determine in which direction you need to wind the fishing line for the trimmer. To do this, take a look at the bobbin on which there can be an arrow or inscription. She indicates the side of winding. If there are no designations on the coil, then look at the arrow on the mowing head. carry out windings in the opposite direction.
Wash the consumable material carefully, a round to the round. Try to adhere to maximum thread tension.
After completing the cord laying, fasten first the short end of the material. To do this, insert it into the groove on the side of the coil, which is suitable in diameter. The second end (more authentic), attach to the groove on the other side of the backpack of the trimmer for the grass.
By fixing the fishing line for the trimmer, cut its ends. Do not forget to leave allowances about 10 cm.
Install the refitted coil to the mowing head of the device. To do this, you need to insert and pull the thread alternately into the weekend of the head, then place the keyboard of the device in the skin.
By applying the required force, pull the cord from the fixing grooves and tighten the material. At the end of this action, put on the lid and fix it using the latches.

You can wound a cord for a trimmer for grass in another way, in which two segments of the material are charged instead of one. The replacement is carried out like this:

Trimmer heads: types and principle of action

The domestic market offers the owners of trimmers of the coil of several types: manual, semi.automatic, automatic and universal. They differ from each other in both the way of serving the fishing line and the principle of its charging. You can also wound a fishing line for a trimmer in different ways. According to this principle, the coils are classified into quick.charged and collapsible.

Before you purchase a trimmer for grass and/or buy spare coils for it, you must definitely familiarize yourself with which consumables are suitable for a particular model. This is important, since bobbins of different manufacturers can differ not only in the methods of supply and refueling of the cord, but also to the axis of the mount, type of thread, as well as the diameter of the fishing line used. For example:

The fastening axis can be fixed (fixed) or rotating 90 °, 180 ° or 360 °;
For low.power trimmers, a fishing line for a trimmer with a diameter of 1.3 to 1.6 mm is suitable, and for more productive. up to 2.0 mm;
Professional trimmers for grass, as a rule, are equipped with universal heads with a diameter of the cutting cord from 2.5 to 4.0 mm.

Advice! Experts recommend using string heads equipped with ball bearings, as they have an increased service life, while reducing the wear of incoming components. At the same time, for replacement, it is best to choose the bobbin of the manufacturer indicated in the operating guide for the grass for the grass, which in turn will allow you to correctly install the head on its drive.

Manual bobbins

A manual mowing head is a coil in which the cutting cord during wear is stretched by the owner of a trimmer for the grass on its own. To do this, turn off the tool, remove the head and with the help of hands stretch the fishing line for a trimmer to the required length. However, despite some inconvenience, this type of head is considered the most reliable.

Bobbins with semi.automatic control

The semi.automatic coil installed on the trimmer allows you to serve a fishing line for a trimmer using the centrifugal force that occurs when it rotates. In order for the supply to be carried out, you need to touch the head of the coil to the ground and at the same time press the button that opens the anchor mechanism. This key is located on the control handle. At the same time, turning off the trimmer for the grass is not required.

On a note! In the market of trimmer spare parts, semi.automatic coils of two types can be found: single.section, in which the fishing line for a trimmer is wound evenly on both sides, and two.section, where the cutting cord must be refueled separately in each section.

Bobbins with automatic control

In the automatic heads, the supply of the cutting cord occurs when the speed of the trimmer engine is changed. To pull the fishing line for the trimmer outward, reduce, and then increase the speed of rotation of the engine shaft. As a rule, the coils of this type are equipped with a metal core, due to which their breakdown is practically excluded.

Bobbins are universal

The universal type of heads differs from its analogues in that they can be installed on various models and electrimmers’ models. They are characterized by high strength and reliability during operation.

Bobbins are quick.charged

Coils of this type allow you to refuel a new fishing line for a trimmer without disassembly. To do this, one of the ends of the cutting cord is stuck inside the bobbin, and then wrapped several times around its surface. After the required amount of fishing line is wound, the latter is cut off.

Bobbins collapsible

To refuel the fishing line into the head of this type, it must be removed from the grass.shirt and disassemble. Having wound the required amount of cutting cord, the coil is collected and returned to the place.

On a note! Currently, almost all electro- and benzotrimers are equipped with mowing heads that allow the fishing line for the trimmer to change to the knife.

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.automatic braid head. Coil malfunctions can be as follows:

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

Option 3. a fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

There are situations when a user of a trimmer for grass notices a very fast fishing line consumption. At the same time, he never hit the ground with a button to lengthen the fishing line. The reason that the fishing line for a trimmer spontaneously lengthens, cutting off a special knife on the casing of the device, may be the absence of a spring in a mowing head. Often beginner users of mowers, trying to charge a fishing line for a trimmer into a coil, forget to install a clamping spring in the head, or completely lose it when opening the lid, and in the future, they do not even suspect its existence.

Also, a fishing line for a trimmer can lengthen without using a button if the spring is weakened. If the spring check confirmed this fact, then it is necessary to put several goals under it to strengthen its clamping properties.

Are Battery Lawn Mowers and Grass Trimmers Worth It?

Automatic winding of the fishing line on the reel

There is a type of coils, in which the automatic mechanism performs winding without the help of others. it is enough to correctly season the fishing line for a trimmer from the user. How to refuel a fishing line for a trimmer to a trimmer coil for grass? annotation. How to remove a coil from a trimmer for grass? How to wind a fishing line for a trimmer in in order to season a fishing line for a trimmer. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are tied through the hole on the external case, the bobbin is assembled, and when rotating the winding button for the trimmer, it is wound without the help of others. In such a spool, it is unrealistic to make the winding incorrect: the mechanism itself will determine the correct direction, because it can spin exclusively in one direction.

Warranty production of factory gas stations Trimmer for grass

Besizbelly demands fishing line substitutions. Having a very approximate idea of how to tuck a fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate this process.

Typical problems. reasons

Malfunctions, most often happening to Magneto, are typical of trimmers of different manufacturers. As a rule, this is a weak spark or its absence, as well as the presence of interruptions in this process.

Unstable sparking

If Magneto gives a spark with interruptions, you must first check the contacts. They could burn or get sick. The detected carcass is cleaned with a file, and the oil is rubbed with suede, previously soaked in gasoline. The second possible cause of the problem is the adjustment of the clearance between the contacts. To eliminate it, you need to set the right distance.

If the spark appears with interruptions, this may also mean that the pillow of the interrupt lever is worn out. To eliminate the malfunction, it is necessary to change the lever for the new. In addition, the clearance should be adjusted, as with another possible reason for the breakdown. the alcohol of the album.

The breakdown of the capacitor can also be the culprit of interruptions in the formation of a spark. In such a situation, it requires replacing the damaged part, since it is impossible to repair and re.charge it.

Lack of sparking

If Magneto does not give a spark at all, the main reason is to break off one of the transformer chains (primary or secondary). To fix the lawnical mower, a faulty part should be replaced. If the primary chain to the mass is closed, this can also cause a lack of a spark. It is necessary to eliminate it to correct the problem.

On a note! The punched insulation of the high.voltage wire can also cause breakdown. You can fix the situation by replacing the wiring.

Insufficient sparking

A weak spark on Magneto is caused by a damaged capacitor. To eliminate the breakdown, it is necessary to replace the failed part.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections

Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Trimmer heads: types and principle of action

Before you purchase a trimmer for grass and/or buy spare coils for it, you must definitely familiarize yourself with which consumables are suitable for a particular model

This is important, since bobbins of different manufacturers can differ not only in the methods of supply and refueling of the cord, but also to the axis of the mount, type of thread, as well as the diameter of the fishing line used. For example:

The fastening axis can be fixed (fixed) or rotating 90 °, 180 ° or 360 °;
For low.power trimmers, a fishing line for a trimmer with a diameter of 1.3 to 1.6 mm is suitable, and for more productive. up to 2.0 mm;
Professional trimmers for grass, as a rule, are equipped with universal heads with a diameter of the cutting cord from 2.5 to 4.0 mm.

Manual bobbins

A manual mowing head is a coil in which the cutting cord during wear is stretched by the owner of a trimmer for the grass on its own. To do this, turn off the tool, remove the head and with the help of hands stretch the fishing line for a trimmer to the required length. However, despite some inconvenience, this type of head is considered the most reliable.

How to choose a trimmer for the head of the head?

So that the head of the mower is highly efficient, the owner of the bushore should approach it correctly. In this case, several factors should be taken into account:

An experience. If the buyer. Novice gardener, it is best to buy an automatic coil. Semi.automatic and manual coils are best suited for more experienced gardeners;
Material. The reliability of the coil depends on this. They are considered the most durable metal models, but they weigh much more than standard plastic devices. When working with a metal coil, the braid engine is under a large load, so you only need to buy them to work with a powerful brush;
The diameter of the used mowing fishing line. For medium power trimmers, coils are used, which can be tightened with a wire thickness of not more than 1.6 mm. lawn mower with a capacity of more than 2.5 liters. FROM. Lamps can be installed that can be delayed using a cutting cord with a thickness of more than 2 mm.

Best Grass Trimmer #shorts

An important role in choosing a coil is also played by the simplicity of its design. For beginners, coils consisting of a minimum of parts are best suited. experienced gardeners can use heads with a large number of elements in their design.

TOP 3 most reliable drums for home use

The market has a rating of the most durable mowing heads. They are distinguished by the simplicity of the device, reliability and resistance to damage. These include:

3rd place. Bosch K-103. This is a universal coil weighing about 300 g. Most often used to equip Makita and Hyundai motolers. The model is characterized by low energy consumption, impact resistance and durability. The core and its other parts are made of forged steel, and the case. From plastic;

2nd place. Flymo 15. This semi.automatic model of a trimmer for grass is equipped with a thin cup, which increases the flow rate. Nevertheless, he worked perfectly when he mowed grass in rocky terrain. To work with it, you need to use only a thin fishing line for a trimmer;

1st place. EFCO 8100. This model is one of the most reliable mowing heads. It works in fully automatic mode, which facilitates its filling with a cut cord. Only thin hair is used to work coil. The model of the model is made of durable multilayer plastic.

Despite stability and durability, all these coils are much cheaper than other analogues of lower quality, which makes them leaders in the post.Soviet market.

TRAMER REPAIR OF THE TRAMMER for Grace with your own hands

Trimmer for grass, whether it is gasoline or electric, is the only right solution for mowing grass in hard.to.reach places that a wheelbreak cannot cope with. As a cutting tool in trimmers, metal knives or a special fishing line for a trimmer are used, which is refueling in the coil of a trimmer for grass. But, unfortunately, trimmer heads during operation over time become unusable. Some malfunctions can be eliminated with your own hands, and with some you will need a complete replacement of the mowing head.

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

Option 3. a fishing line for a trimmer was soldered inside a mowing head. This leads to the fact that the coil is stopped and does not spin when the button is pressed.Basically, this happens for several reasons: poor quality of the cord, overheating of the coil with prolonged operation of the unit, a fishing line on solid items.

In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

The main malfunctions of the coil

Users of the electrimmer and lawn mower often face a problem associated with a semi.automatic braid head. Coil malfunctions can be as follows:

The fishing line for the trimmer does not extend automatically

If, with a light blow, the trimmer coil button for grass on the ground is not lengthened for a trimmer, then the reasons for this may be the following.

Option 1. there was a snack, t.e. Squeezing the cord between turns. This problem usually appears if the user wound a fishing line for a trimmer to the coil unevenly, with the intersection of the turns, or wound it with insufficient tension. In the latter case, when the mowing head is rotated at large revolutions under the influence of centrifugal force, the cord begins to drag on, as a result of which the interitral clamping of the fishing line is possible. To eliminate the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, with even turns with good tension.

Option 2. too short ends protrude from the head. A fishing line for a trimmer may not exit when hitting the ground, if its ends sticking out of the head, insufficient length (short). In this case, the centrifugal force is not enough for the fishing line for the trimmer to stretch. Therefore, it is required to stop the unit (drown out the engine or turn off the ethletric trimmer for grass from the network) and pull the fishing line for the trimmer manually, after pressing the button.

In the first case, the cord of third.party manufacturers can be made of low.quality and fusible materials that do not withstand the mechanical and temperature load. Therefore, preference should be given to “branded” fishing.
But, if you still purchased a fishing line for a trimmer of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after refueling the cord, moisten it either with silicone grease (from the spray can) or mineral oil). This procedure greatly reduces the likelihood of soldering a fishing line among themselves.
Also, a fishing line for a trimmer can sleep if during a mowing it hit a hard object (stone, fence, dry branch, etc.D.). As a result of this, it is slightly stretched and draws back into the head with high speed. The cord is heated from friction, and its turns are sticking together. The only thing that can be done to eliminate this malfunction is to open a trimmer coil for grass and rewind a fishing line for a trimmer.

The cord spontaneously lengthens

Knife nozzle for a trimmer for grass

Walking shopping in search of spare parts is an ungrateful thing, and I refused this thought right away. What is the point of wasting time and money if a new part lasts no longer the previous one, but only until the first meeting with some kind of piece of iron lurked in the grass. It is better to immediately replace a broken reel with a home-made nozzle with stainless steel knives (see. a photo).

The design of the nozzle is very simple. For its manufacture, it took only four details: the central sleeve, the washer and two knives-knives (see. rice.)

I made a central sleeve out of a pruning of a conventional tap pipe. To adjust its inner diameter to the diameter of the shaft, on one side of the blank made a through longitudinal section and slightly besieged with a hammer. The sleeve should sit on the shaft tightly, without backlash.

The puck of suitable sizes I managed to choose the finished. But, if there is no one, it is not difficult to cut it out with a sheet steel with a thickness of 34 mm and finalize with a file. I put on the puck on the sleeve and welded at four points. This is quite enough.

The knives-knives cut out of the sheet stainless steel 1 mm thick. The knives are attached to the puck on rivets. They must be steel. I used M4 screws as rivets. They must be blown up so that the knives are not firmly pressed to the puck, but they can turn freely. This is a very important point. If the knives are fixed hard, then they will surely bend or break at the first meeting with the stem, which will not be able to cut down the shaft of the trimmer for the grass.

The collected nozzle is put on the shaft of a trimmer for the grass and fixed with a copper copping cup of ∅3 mm. Shplint’s hole is best drilled in place.

The first tests of the trimmer for grass with a new knife nozzle confirmed its effectiveness. Knives easily “took” almost any grass. And with leisurely work, the electric motor was practically not overloaded. In a word, what is necessary!

However, we should not forget that metal knives are a more serious danger than a thin, almost weightless fishing line for a trimmer. Therefore, to mow grass around the house is desirable when there are no people or pets nearby. And, of course, it is necessary to constantly monitor the wear of the knives and the rivets attaching them.

Universal heads for motorcycle and what is better to choose

The above options make it possible to understand what type of head on a motorcycle is preferred. In the presence of finances, it is better to choose automatic models, and if the products do not allow you to buy a good branded head for a trimmer for automatic grass, then you should choose from the semiautomatic segment.

When choosing coils for your tool, you can find out that manufacturers, in addition to branded devices, produce still universal ones, that is, those that can be used in conjunction with different models of trimmers. This is convenient only in one case, if there are two or more tools for driving grass of different manufacturers.

A number of advantages of universal coils include:

Suitable for most trimmers and benzos different manufacturers
Low cost, but at the same time they do not differ in particular reliability, so a special approach is needed for their choice
Prevalence. if you find a proprietary coil for a specific model of a trimmer for grass, it is quite difficult, then there are no such problems with universal models

It is interesting!Heads are metal and plastic. Metal ones are more expensive, but devices made of good high.strength plastic are not inferior to them, and sometimes they even cost more.

Sources:

https: // Tool-nd- Tools.ru/Dlya-Sada/Kak-Razobrat-Trimmernuyu-Golovku.HTML
https: // technorama.ru/Info-Baza/Kak-Namotat-Slesku-Na-Katushku-Trimmera.HTML
https: // tytdacha.ru/sadovaya-tehnika/gazonokosilki/kak-amotat-lesku-na-Trimmer/
https: // Tehnostroiplus.RU/Sad.ogorod/Kak-Razobrat-Golovku-Trimmera.HTML
https: // xnh1aaasb2a.XNP1ai/Instrument-Dlya-Ulicy/Kak-Snyat-Katushku-S-Trimmera.HTML
https: // 101benzopila.ru/kak-razobrat-katusku-gazonokosilki/
https: // 101benzopila.ru/kak-razobrat-katusku-gazonokosilki/
https: // Tool-nd- Tools.ru/dlya-Sada/kak-otkryt-katushku-trimmera.HTML
https: // technorama.ru/Dreli/kak-otkrutit-katushku-na-trimmeere.HTML

Lawn Mowers coil, disassemble, grass, lawn, mowing, trimmer