How to Wear a Trimmer Strap

Working with a trimmer is much more convenient and easier with a special belt. Thanks to him, the operator can mow large areas of grass for several hours without pain in the joints and muscles. The design of the two-shoulder belt is designed in such a way that the Lawn Mower is held with the help of fastenings itself. without the help of hands. She only needs to set the direction, and she will do the rest herself. How to properly attach the belt to the trimmer and adjust it for yourself to ease the load, and we will talk about this material.

Trimmer Backpack Strap. Intended Use

Many models of trimmers are equipped with a regular slanting belt. However, for work, it is best to purchase a backpack belt that is specifically designed for scythes. Thanks to a well-thought-out design, it evenly distributes the weight of the device to the whole body. Padded shoulder pads reduce severity and relieve pain in the forearms. A hard back disperses the load between the upper and lower back, excluding the lower back. Shock-resistant protection for the thigh prevents the brushcutter from contacting the leg so that it does not rub and does not transmit vibration. In addition, the belt provides:

  • convenient transportation of the trimmer;
  • comfort during operation due to ergonomic position of the braid relative to the body;
  • safety at work. a knapsack belt prevents the scythe from slipping out of your hands when hard objects get under the knife.

How to Wear a Trimmer Strap

What is a backpack belt

It should be understood that the weight of the refueling brushcutter is on average 6–9 kg. And this device must always be kept in limbo. In order to evenly distribute the load, the backpack belt seems to encircle the body from all sides. The main load falls on the shoulders and back, so its upper part is complemented by wide foam inserts and fabric straps. Further, the belts descend along the body and, with the help of a quick-detachable clip, are connected to each other in the area of ​​the chest or abdomen. And so that under load the belt does not crash into the body, a wide and durable lining is provided. A plastic foot protector is attached to the belt. It has a snap hook for attaching to the trimmer and spring cushioning. Easy to unfasten and fasten Lawn Mower provides a quick-release latch located on top.

On a note! Different models of knapsack belts may differ among themselves in the design of locks, carbines, the presence or absence of additional pads and latches. However, the principle of design and operation is the same for them.

Belt adjustment

To ensure comfortable working conditions, you need to be able to correctly wear a backpack belt. This process requires some skill, but then, after adjusting the satchel for yourself for the first time, it will be worn much faster and easier.

Video: How to Wear a Trimmer Strap


Hook height adjustment

The most important thing is to adjust the belt so that the trimmer is at the right level from the ground. To do this, raise or lower the height of the hook, which is done by tightening the shoulder straps until the holder is below the hips by 10-15 cm (palm width). In this case, the knife of the attached braid should be parallel to the surface, that is, in strictly horizontal position.

On a note! If the trimmer is attached too high, it will severely limit grass grabbing.

Balancing the scythe by moving the abalone

After fixing the required height for yourself, you need to balance the trimmer. To do this, the eye is rearranged, with the help of which the device is suspended from the belt, forward or backward. As a result, you need to attach the belt to the trimmer so that when releasing the steering wheel, the knife or saw blade did not lie on the ground, but hung over it, without touching the surface. How far it will be located depends on the goals set.

Advice! A distance of 20-30 cm above the ground is suitable for mowing tall grass, and for lawns you need 5-10 cm.

Shoulder strap adjustment

In order for the load to be distributed evenly on the shoulders and back, you need to adjust the shoulder straps well. To do this, it is enough to tighten or relax the straps. they should not dig into the body or hang down. You can understand how the weight will be dispersed if you press the hook for hanging the braids with your own hands.

Securing the brushcutter to the belt

Depending on the model, the gasoline braid can be mounted on a belt using a strap or loop. In the latter case, to balance, you need to move it around the bar to get the desired result. In some cases, shock absorption mechanisms are provided that smooth out the vibration and soften the sharp jumps of the trimmer.

Handle balancing

An important step in adjusting the knapsack belt is also to adjust the handles to the optimum level. When the operator will hold the motocosa, his hands should be relaxed, and his shoulders should be parallel to the body. Therefore, after fitting the two-shoulder belt, the two-handed mechanism should be adjusted by moving it up or down. It is necessary to achieve such a result that the hands only set the direction, and not hold the device. If after this the trimmer balance is again disturbed, you will have to repeat all the steps again.

Safety regulations

Among the safest and most popular trimmers, products from German manufacturers (including Denzel) are especially valued, as they pay increased attention to quality and reliability. However, despite the brand and model, there are a number of rules that must be clearly known and observed when using the trimmer.

  1. Before use, it is necessary to familiarize yourself with the instruction manual.
  2. You can not work with the trimmer in a state of fatigue, illness, intoxication.
  3. It is forbidden to use the braid in explosive and fire hazardous areas.
  4. Do not mow during thunderstorms and rain, or after rain when the grass is wet.
  5. You can only work in the daytime, in good light conditions.
  6. Use only the type of fuel and lubricant that is suitable for the particular trimmer model.
  7. It is not recommended to repair the tool yourself.
  8. Do not touch rotating or heating elements during operation.
  9. Do not smoke or make fire during mowing, etc.

Important! When using the trimmer, there are other factors harmful to health: increased noise, vibration, exhaust fumes, high temperature of some parts, flying branches, etc. To minimize risks, you need to use protective clothing, glasses and headphones.

If you still have questions about adjusting the belt-backpack of a specific model of scythe, you can try to find the answers in the instruction manual that came with the product, or watch a video on the Internet, where it is clearly and readily shown how to set up and adjust the belt together with the scythe.

The best trimmers

Huter GET-400 trimmer on Yandex Market

Trimmer STAVR TE-1700R on Yandex Market

Makita UR3502 trimmer on Yandex Market

How to Wear a Trimmer Strap Video

How to mow grass with a trimmer?

The main thing is to correctly adjust the trimmer belt so that the drum with fishing line does not crawl along the ground.

Properly make a gasoline-oil mixture.

Do not use too thick fishing line. it picks up speed and overloads the trimmer.

Do not be afraid to give him speed.

Do not wind too much fishing line on the drum, and do not wind it too much.

Stop from time to time and empty the basket.

Lubricate the trimmer cable and gear (if any) with a grease gun.

The question author chose this answer as the best

The technique of mowing grass with a trimmer is not very complicated and takes into account the need:

  • Decide how exactly you are going to mow. It is possible to fold, crosswise.
  • choose a place so that a bald spot does not appear as a result and the site looks harmonious
  • understand what exactly you are going to mow, and depending on the choice to put the right knife. They are different. For example, hay or weed. You also need to set the speed.
  • Of course, it is necessary to prepare both clothing and protective equipment. Whatever you are an experienced mower man, but glasses must be worn. and don’t forget the headphones and long clothes.

All the details of the technique are on the video how to mow with a trimmer.

add to favorites link thank

First of all, inspect the area that you have to mow. Cut off bushes or large flowers that cannot be cut on your own.

Always start with a light area where there is little grass. See if there are slopes or ditches in the area. The easiest way to mow across the slope.

Determine the direction of the grass. Mowing is easier if the grass is tilted forward.

As for clothes, you should always wear glasses and boots. Also anti-vibration gloves do not interfere.

Use different knives depending on the density of the grass.

One more tip: try to mow at the same speed. This way your mower will last longer. If you stop and immediately pick up speed, then the trimmer will wear out faster.

Correct mowing with trimmer:

  • choose the fishing line correctly. For different tasks, there are two different subjects. fishing line and knife. Too wide fishing line is undesirable, as this will give overload to the trimmer. As a rule, on a simple site fishing line is enough.
  • when cutting is installed (fishing line or knife), it is necessary to tighten and fasten the nut.
  • Check the charge or availability of fuel. Put on the belt comfortably.
  • movements when mowing with a trimmer should be thought out. The algorithm is: right-left-left-right. This will give the maximum result. Yes and be attentive to work. It is necessary to control that there are no children or animals near you. You should also wear a mask to protect your eyes.

add to favorites link thank

First, adjust the trimmer belt so that the drum does not touch the ground. Further, it is important to remember that due to the thick fishing line, the trimmer will be overloaded, so do not overdo it with the thickness.

A lot of fishing line on the drum is not worth winding.

Remember to periodically clean the trimmer.

Lubricate the cable with a solid oil.

The trimmer is very convenient as it can be used in a variety of places, including complex terrain and areas near trees. If you mow tall grass, first start with the protruding tops and then continue with the bulk.

add to favorites link thank

Use the trimmer as intended. An electric scythe (that is, a trimmer) is good because it copes well with its work in hard-to-reach places. Therefore, the trimmer can be used near trees, fences in relief areas. And not only for mowing the lawn, but also ordinary grass.

The main thing. this is to ensure that the weeds do not have time to give the seeds and mow them in time.

If you did not have time to mow the grass until the moment it gave the ears, then first mow the tops of the ears and burn them. And only then mow the grass itself, and put it into compost.

add to favorites link thank

In almost all trimmers (if there are no special ones), the fishing line or the disc rotates clockwise. That is why it is better to mow the grass with a movement from right to left (a movement that resembles movement when mowing with an iron scythe). It can be mowed by tilting slightly towards mowing.

You need to mow with calm movements, not jerks. Mow grass half the length of the fishing line. If you grab more, the trimmer can handle it, but grass can clog the space between the coil and the tube.

Mow, squeezing the gas to full.

add to favorites link thank

Before mowing the grass, first adjust the fishing line and firmly fix it in your cavity so that the fishing line does not hang out and go there. here. Then fill the fuel accordingly (if you do not have an electric trimmer) which consists of special oil and gasoline. Next, start mowing the grass with smooth movements (not fast) to the right and left. Do not try to chop thick stems of plants often, as the fishing line will instantly end, and you will have to adjust the reel again. In dense places, the main thing is not to spare gas)

add to favorites link thank

The trimmer from the company Varyag koshu according to the instructions:

Step 1. Install the cutting mechanism.

Depending on the type of weed grass, we choose a cutting tool: for soft-stalked grasses. a fishing line, for hard-stemmed and small shrubs. a knife. Unscrew the nut securing the cutting mechanism and install the cutting tool. Tighten the nut. the mechanism is ready to work.

Note: some trimmers do not have interchangeable cutting tools, so you can start working with them right away.

Step 2. Preparing the trimmer for work.

If the trimmer is electric. we charge the battery or turn on the motor in the network. If gasoline. fill the tank with fuel. Then, depending on the type of trimmer. we adapt it to ourselves (upper-motor. is hung with a loop on the shoulder, knapsack. for the shoulders, lower-motor. we take the handle). We hold the trimmer over the grass so that its cutting mechanism is parallel to the treated area. We start the engine.

Action 3. Mowing.

Grass mowing with a trimmer is carried out with simple movements. It is important to remember that the cutting mechanism of the device rotates counterclockwise, so that the mowed grass will fall on the already treated area. The first is from right to left in front of us (this is how we cut off the top of the grass). The second is from left to right (this is how we remove the rest of the grass).

It is better to divide a large area of ​​the cultivated area into squares, and mow grass on them, moving from one to another on the outside of each square.

When mowing grass on the slopes, it is recommended to mow from below, moving parallel to the sloping area. We reached the edge, went back, became a little higher. and we repeat the same route. until the site is completely mowed.

For mowing grass on a site where there are trees, it is better to use a forest cutting mechanism, and you need to mow, passing the site along the perimeter, bypassing the tree around the trunk.

Step 4. Finish the job.

After mowing all the grass in the area, you need to turn off the engine, remove the trimmer (for shoulder and knapsack devices), clean the cutting mechanism of the rest of the grass.

Video: How to Wear a Trimmer Strap Video


»How to configure

How to properly configure the brushcutter belt for yourself

author: fazenda | June 2 | Views: 10082

Specialists of service centers often complain about consumers of household gardening equipment who, at the stage of its assembly and first start-up, make mistakes and disable equipment. Of course, there is an instruction in the package, but either it is stupidly written, or it is read after improper assembly, when extra parts were discovered or, worse, a breakdown occurred. Meanwhile, there is nothing complicated in assembling household gardening equipment. You just have to be careful. Let us give an example of the assembly order of the Stihl FS 130 petrol scythes, complementing our instructions with illustrations.

1. Begin assembly by opening the box and checking the assembly of the unit. If everything is in place, then we have to fasten the handle to the rod with the motor, put on a belt, attach a protective cover and cutting elements.

2. First you need to remove the handle and unscrew the thumb screw that secures the upper part of the support without losing the springs.

3. Insert the handle into the socket and fix it without tightening it much. We will adjust the final position after the final assembly of the brushcutter.

4. We put the control knob of the unit on the handle tube and tighten the fastening bolt. To do this, the kit has a universal key.

5. All Stihl FS 130 petrol brush controls are located on the handle. These are: the throttle lever, which has protection against accidental switching on and the shutdown lever of the unit, which is controlled by the thumb. In the modification of the brushcutter with a D-shaped handle, the controls are located next to the engine on the rod.

6. We put a plastic protective cover. If you plan to use only a knife, then for its work we use a part of the casing (in the picture it is painted in orange).

7. If there is work to be done with a cutting line, then a plastic skirt is additionally put on the protective cover of the chainsaw and a knife for cutting the line is placed. In some varieties of this model, the cover can be universal or two different covers can be attached. one for the fishing line and the other for the knife.

8. Sliding the skirt over the casing, you must check the reliability of its fastening. Sometimes it may be necessary to fix this protection with another screw.

9. Now you need to put the knife for cutting the fishing line and fix it with a screw.

10. It remains to install the reel, pre-filling it with fishing line. The coil is screwed onto the shaft (as in the illustration) or fastened with a special nut. Keep in mind that the thread on the shaft is usually left. How to fill the fishing line into the reel, read the instructions.

11. If a knife is required, then we put it instead of a coil. The knife is equipped with a protective cover so that during operation it does not dig into the soil. After installing it, do not forget to scroll this cutting element and make sure there is no play.

12. Well, the last, simplest step is to install a metal clamp on the rod, i.e. fastenings for a suspension belt.

After the brushcutter is assembled, we put on a shoulder strap or a knapsack belt suspension (depending on what is included in the kit) and customize them according to the figure. Fill the gasoline mixture, start the engine. and go.

Trim belt How to Adjust the Trimmer Knapsack

1. Adjust the height of the hook of the trimmer knapsack belt pulling the shoulder straps so that the trimmer knife lowered to the ground is parallel to the surface of the plot (strictly horizontal).
When operating the trimmer saw blade, adjust the height of the hook (by lifting the shoulder straps) so that the trimmer blade is tilted slightly forward relative to the ground.

2. Moving the ear to hang the braids on the trim tab forward or backward, balance the trimmer so that when releasing the steering wheel the trimmer knife is near the surface of the site, but does not lie on the grass.
To saw bushes and young trees with a saw blade of a brush cutter, the trimmer must be balanced so that when the steering wheel is released, the machine hangs horizontally on the hook horizontally. Attach.

3. Adjust the trimmer shoulder straps (harness straps) so that the load is distributed evenly over the shoulders (check by hand pressing on the hook of the trimmer suspension).

Video about the Husqvarna trimmer backpack. On the design features of the belt suspension (harness) that facilitate and make mowing with a motor-scythe, trimmer, chainsaw, brush cutter Husqvarna easier. wide shoulder straps and an elastic waist belt, quick-release locks (carbines) in case of fire or any other situation requiring quick release from the trimmer. On the versatility of belts for men and women.

Such Husqvarna trimmer knapsack belts (Balance 35/55, Balance X, Balance XT) can be used on any trimmers, petrol scythes, scythes, electric scythes, brush cutters.

Share link:

Post navigation

Recent comments

Site Subscription

How to Wear a Trimmer Strap Video

Teeth properly cleaned food after

When to brush your teeth: before breakfast or after? Surely everyone knows that you need to brush your teeth twice a day. Imagine morning without

Watch how to brush your teeth

How to brush your dog’s teeth at home Hello! I Kulkova Nadezhda Petrovna, senior veterinarian, specialist in veterinary dentistry

See how to clean pomegranates

How to clean the pomegranate from the peel. Video Description: There is a custom in hot and sunny Georgia: if a young man is in love with a girl,

How much to brush your teeth

Brushing Teeth Correctly Currently, there are both general and individual recommendations regarding the correct brushing of teeth and oral cavity. And the question is, how long does it take to clean

Interesting

The right trimmer belt

There are trimmers for which additional accessories are not needed. for example, lightweight battery-operated electric trimmers. Even a child can carry them, and they firmly lie in his hand, not breaking out. However, most often trimmers weigh from 6 to 9 kg, and in order not to get tired of moving them from place to place, you need a belt.

Why else do I need a trim belt?

1) To transport the trimmer. Transporting a trimmer to the cottage when there is no car is a complicated matter. If the equipment does not have a belt, then at least a cover with a belt should be sewn over the shoulder. This will ease the load when transporting the trimmer.

2) For convenient mowing of grass. After all, if your hands get tired, then you will not want to mow the weeds and the overgrown lawn. And if you want, then trembling hands from fatigue is an unsafe option.

3) For the ergonomic position of the trimmer relative to the body. Properly fastened and adjusted along the length of the belt to protect against lower back injuries and overstrain of the muscles of the back.

4) For security. The trimmer will be much safer if it decreases the likelihood of it slipping out of your hands when branches and hard vegetation get into the cutting head. When this happens, the trimmer, whether it be a petrol or electric braid, makes a sharp jerk, and the trimmer literally “breaks out” of the hands.

For these reasons, many models of garden trimmers equipped belts. They are threaded through the trimmer shaft and mounted over the operator’s arm. The belt helps balance the total weight of the trimmer and the operator, and you don’t have to balance the balance by stretching your arms or putting one leg back.

How to attach the belt to the trimmer?

1) Find the place where the belt fastens to the trimmer shaft. On many models designed for amateur gardeners, a hook, screw, or groove is located next to the ignition handle or toggle switch.

2) Squeeze the carabiner belt and hook it on the eye on the trimmer handle. Find the second hole for the belt and do the same.

3) Throw the trimmer with the belt over your back so that the upper part of the belt goes over the left shoulder (for left-handed people. over the right one).

4) Adjust the length of the strap so that the lever, which is responsible for mowing power and continuous mowing, is at a convenient height of the arm slightly bent at the elbow. In width it is necessary to monitor that from the body to the trimmer was at least 10-15 cm.

5) Put your right hand on the lever and the left hand on the top panel. Move the head of the trimmer, feel where the center of gravity is located at the trimmer. If the weight is still unbalanced and you have to bend over, or you make an extraordinary effort to hold the device, try pulling the belt higher or lower by 1-2 cm. After you have completely dealt with the belt, you will feel what position with the trimmer most comfortable

6) Stop cutting grass in case you have pain in the lower back and arms. Adjust the belt again.

What should be the trimmer belt?

The leather belt is best suited for the trimmer: it does not slip and fixes the equipment quite rigidly, and the skin is pleasant to the touch.

In the area of ​​the shoulder, you can make a special quilted pad that will make the shoulder load less noticeable and reduce friction.

Remember that a correctly selected belt for the trimmer is essential will increase comfort and speed with this garden equipment. This means that health, mood and lawn will be in perfect order.

How to Wear a Fishing Line On a Mower

IMPORTANT! To bookmark an article, click: CTRL D

How to Wear a Fishing Line On a Mower

Replacing fishing line on trimmer or Lawn Mower

Replacing fishing line on trimmer

To replace fishing line on trimmer or motokose (cord, strings), first of all, you need to know its thickness. If the remains of the cord are not preserved, then we study our passport garden equipment. Sometimes the necessary information can be found by carefully inspecting the mowing coil, a range of diameters can be applied to its surface. If our searches were unsuccessful, then we simply estimate the diameter of the outlet on the coil. The fishing line should move in it effortlessly. I do not recommend expanding the holes in order to use a thicker string to increase productivity and the possibility of gardening equipment. The thickness of the fishing line is calculated by the manufacturer based on engine power.

To replace the cord on most models, it is necessary to disassemble the mowing coil by pressing the latches. Sometimes, simultaneously with pressing the latches, it is also necessary to turn the upper part of the coil.

5-6 meters of thin cutting fishing line or up to 3 meters thick are tucked into a standard bobbin. The numbers are approximate, it all depends on the size of your mowing head. If it overheats during mowing, it is better to refuel less mowing line. There is a chance that it will bake, and you just throw it away.

In the simplest trimmers and motocosa there is a non-automatic coil with one antennae. Everything is simple there, we fix one edge of the fishing line in the slot inside the bobbin. Then we wind as much cord along the arrow as it fits under the protective cover. We output 10 cm of the string through the holes in the protective casing and coil and collect it.

Video: How to Wear a Fishing Line On a Mower


Single-bar manual coil

Semi-automatic single-section coil with 2 antennae

Semi-automatic two-section coil with 2 antennae

If the fishing line on the trimmer has 2 antennae, then before winding the string is folded in half, shifting the edges by 5-10 centimeters. The bobbins come in different designs, but each one has a hook for fixing the middle of the cord. If the bobbin is single-section, that is, a hole where you need to thread one end of the fishing line and center it again. In a two-section coil, a cutout is located in the baffle.

Wind-cord and directional arrow

The inscription “Wind kord” and the arrow show us the direction of winding. If there is no arrow, then we wind to the side opposite to the direction of rotation. With one hand we hold the edges of the cord, and with the other we rotate the bobbin, winding the fishing line, each side on its path. The string is laid tight enough, ideally exactly unnecessary, the main thing is to prevent intersections. She herself, at work, will take the right place. When there are 10 centimeters left, we fix the edges in the slots. Pass the string through the holes on the coil body. Alternately, we easily twitch the fishing line so that no loops form inside, and insert the bobbin into the reel. Then we collect the mower coil. Sometimes there is such a coil design that when it is assembled, the edges of the string must be freed from the slots of the bobbin. You can check the correct assembly of the semi-automatic head of our garden equipment by imitating the tapping of the trimmer on the ground. We press the button in the center and at the same time pull the edges of the fishing line. If everything is in order, the antennae are slightly extended.

On Oleo-Mac scythes, there is no need to disassemble the cutting coil at all. Just thread the string through the holes. We center it, and by rotating the “lamb” in the direction of the arrow, we wind the cord. Replacing the fishing line on the trimmer is very fast, this design begins to occur more often.

I hope you find the article on the proper selection of fishing line for your garden equipment “Fishing line for trimmer, string, cord for electric and motocosa".

Video how to wind a fishing line on a mowing head of a trimmer or a Lawn Mower using one or two pieces of fishing line:

How to Wear a Belt From a Trimmer Priority

Choosing a Gasoline Lawn Mower for a Cottage

Maintaining order in the garden area certainly requires timely grass mowing, in which a gas trimmer will help every gardener. After all, it is not always convenient to do this with the help of a wheeled lawn mower or an ordinary scythe, and leave the weed grass to grow # 8212; not the best option, since the cottage on which you want to relax and enjoy its landscapes can turn into an overgrown wasteland.

How to Wear a Belt From a Trimmer Priority

Mowing the grass with a trimmer is very convenient, as a rule, the owners of the plots give priority to gasoline models, because not every cottage has electricity, and the wires create an additional inconvenience. The main thing # 8212; it is to choose the right trimmer, which will be convenient to work with. It is not bad that its power makes it easy to remove even tree growth and shrubs.

Trimmer # 8212; This is a structure consisting of a lightweight bar. A cutting mechanism is attached to one of its edges, and # 8212; engine. It is easy to use, lightweight, practical, suitable for removing grass in difficult places. Also, the trimmer may also have another name # 8212; brushcutter, mowing machine or lawn mower.

It is very convenient to work with a trimmer, (there are no tricks to use) and it is pleasant, because all the time of work it will be accompanied by the smell of freshly cut grass. But for the process to be productive, it is necessary to know exactly the parameters for choosing a tool.

Thinking about choosing a gas trimmer for a summer residence, you need to understand the types of manufactured devices and their technical characteristics.

Features of engines for trimmers

Engine # 8212; This is the heart of the design. The duration and quality of work, which directly depends on it. Often, motors for trimmers are equipped with a single-cylinder two-stroke engine, the power of which is 0.5-3.3 kW. As a rule, it is seasoned with a mixture of oil and ordinary AI-92 gasoline. You cannot take other fuel, so as not to cause overheating and subsequent engine damage.

Two-stroke engines are moody in maintenance, therefore, choosing a gas trimmer, inexperienced users are recommended a tool with a four-stroke engine. He does not need a mixture, because oil and gasoline are poured into it in different compartments. In addition, such engines are more powerful and able to mow even thick stems of shrubs.

In any case, choosing an instrument, it is worth deciding what kind of vegetation they have to clean. Since if you purchase a trimmer for lawn grass, you can safely stop on two-stroke engines, as they are easier and cheaper.

The location of the gasoline engine on the trim tabs can be upper or lower:

  • from below the motor is placed on electric or battery trimmers. This design is optimally balanced and vibrates less. But such a trimmer can not work with wet grass;
  • the motor is placed on top of electric and gas trimmers. Knives and a thicker fishing line are suitable for them. They will not have problems with wet grass.

Exploring the device of a gas trimmer, and choosing the right model, you probably want to opt for motors from European manufacturers and avoid Chinese ones, but this is unlikely to succeed. Unfortunately, many European manufacturers buy engines from the Chinese, since the cost of collecting them in China is much lower, so in 90% of cases this engine will come across. But, despite this, they are all of good quality and have a long warranty period.

The most famous engines manufacturing companies:

Of these, only Honda is not produced in China.

Choose a cutting tool

The choice of scythes for mowing grass in the country is not limited only to the selection of the engine. An important role is played by the cutting tool, which is equipped with all petrol scythes. Its appearance usually depends on the engine power level. A tool with a small power, as a rule, is equipped with a cord (fishing line), and more powerful ones. with a milling cutter and metal knives.

Trimmer fishing line has a different thickness (1.2-4 mm) and shape:

  • round;
  • square;
  • with rounded protrusions;
  • round;
  • square;
  • polygonal.

With the thickness of the fishing line are determined based on the specific characteristics of the braid. To put too thick a fishing line on a tool for which it is not designed is not recommended. bushings can wear out quickly.

For mowing tall grass in the area, it makes sense to equip the trimmer with knives instead of fishing line, so that the grass does not wrap around the spindle while mowing fishing line. Knives are metal and plastic.

It is recommended to remove green shrubbery with metal knives, and hard plants, dead wood. with plastic. Knives should not be used on rocky areas, as this is prohibited by the safety rules for using the tool. Also, gas trimmers are equipped with a different number of knives, the more of them, the better the braid works. If you are planning to purchase a machine for haymaking, a device with more than two knives will not work for you, # 8212; they will chop grass too finely.

Features of the external elements of the brushcutter

Rod # 8212; the main conductor combining the motor and the cutting system in a single design. In its cavity there is a shaft, which is flexible or straight. The bar can be disassembled, due to which it is much more convenient to store. The shaft design determines its shape. The straight shaft is more reliable for the boom. However, if the landscape of your site is different in height in different places, it is better to purchase a trimmer with a curved shaft.

Types of holding belts

  • The most inexpensive # 8212; these are trimmers with a gasoline engine equipped with a belt on 1 shoulder, but with them the load on the body is distributed unevenly.
  • organic option # 8212; this is a model with double materials, soft shoulder pads come with it, and a thigh pad protects it from vibration.
  • The most expensive # 8212; These are backpack pendants. Their pigtail can be perfectly adapted to individual physiological characteristics.

When choosing a gas-powered scythe, stop at several models, turn it on, hold it in your hands, and only then decide which one will be more convenient to work with.

Prices for gas trimmers from leading manufacturers range from 3,300 rubles to 35,000 rubles. The cost depends on the power of the engine, its volume, design weight and processing width.

How to mow with a trimmer with fishing line?

Video: How to Wear a Belt From a Trimmer Priority


Almost any owner of a suburban or suburban area knows that it is necessary to regularly care for the lawn, otherwise it will lose its attractive appearance and overgrown with grass. To do this, select the appropriate trimmer and use it correctly.

Fishing line selection

First of all, you need to install a fishing line, which will act as a cutting tool. Choosing too thick is not worth it, as it will seriously overload the equipment and this will not lead to anything good. It is better to opt for a not too thin version. it will cut well soft-stalked grass and provide opportunities for increasing revolutions.

Preparation for work

Depending on the type of trimmer, you need to hold it correctly, otherwise mowing the grass will be a very difficult and uncomfortable process:

  • upper motor solutions. they are worn on the shoulder with the help of a special loop and held on it;
  • knapsack options. worn over the shoulders and quite often are the most comfortable, especially with a large lawn;
  • lower motor devices. held by hands by special handles.

After the trimmer has been worn, it is necessary to place its cutting mechanism parallel to the grass.

Right mowing

You need to move from right to left in front of you, so that the mowed grass will fall on the previously processed area, which will first allow you to cut the tops. Then a reverse movement is made, which removes the remains of the vegetation.

When working with large lawns, it is better to divide them into squares. In the process of mowing, it is necessary to move along their outer side, which will not trample the grass once again and cover the entire area. To facilitate the task, it is better to move from below, going parallel to the sloping section, and then returning back.

In this case, the use of fishing line allows you to cut the lawn around the trees, bypassing them around the trunk.

If you mow the grass in this way, this will reduce its spread to the sides, ensuring proper treatment of the territory.

Completion of work

After mowing, it is necessary to turn off the engine and clean the cutting mechanism from the rest of the grass. Regular maintenance of the device will allow it to remain operational and effective for much longer.

Home / → News / → How to work with an electric grass trimmer

How to work with an electric grass trimmer When choosing equipment for a summer cottage, it’s not always worth chasing powerful and dimensional devices. The power of the tool is, undoubtedly, an important parameter, but it certainly pulls the increased weight of the device, its large size, as well as the high price and increased fuel costs. But that’s not the point. If you have a small garden in which fruit trees are densely planted or a small lawn with flower beds and shrubs. then clean it of weeds and mow the grass gently. this is clearly an impossible task for any lawn mower. In such cases, even a hand tool. an ordinary scythe and that will not help: you just can not swing it, bumping into tree trunks. The ideal solution in this case is a good and inexpensive electric trimmer. It is so light, convenient and easy to operate that it always becomes a favorite among women and older people. A lightweight, quietly buzzing electric motor, a handle with convenient handles and a nylon fishing line tucked into the spool are the main components of the electric trimmer.

Electric trimmer efficiency
A trimmer that runs on a household electrical network. relevant on a plot of four to six acres, planted with trees, flowers, shrubs. It is convenient for them to gently mow the grass near the house or along the curb, mow the paths, and an environmentally friendly motor that does not produce exhaust, gas and burning will make it possible to even remove weeds in any indoor environment. greenhouse or greenhouse.
The trimmer cable limits the grass mowing radius, but can be increased with a standard extension cord. If this length is not enough for you, or the power supply parameters do not contribute to the normal operation of the electric motor, then you can purchase a kind of electric tool. a cordless trimmer. It works autonomously, the built-in battery lasts for half an hour or an hour of intensive work. it is enough to mow the trees in the garden.
The motor at the trimmer can be placed at the top of the tool or at the bottom. Upper-motor trimmers work well on bumpy and uneven terrain. They are also well balanced and can work with tall and wet grass. a short circuit will not occur. The convenience of working with it is also enhanced by a single-arm loop, which is hung on the shoulder.
The lower motor trimmer can only be used for wet grass and for flat areas. Often, lower motor trimmers operate on a battery.

How to use a trimmer
The household trimmer is the easiest to use and at the same time very effective tool. It seems that there is nowhere easier. to plug the instrument into a power outlet and work. But still there are some nuances that you need to know in order for the trimmer to work long and productively.

1. Site preparation. It is necessary to carefully examine the mowing area and remove all foreign objects. stones, glass, wire, etc. Suddenly flying out from under the fishing line during operation, such an object can cause injury.

2. Installation of a cutting system. There are low-power trimmers that can only work with fishing line, mowing soft and juicy grass. they do not need to install a cutting system. But some models of trimmers, in which the motor has 1 kW and more power, can work with a knife. If there are hard weeds or even small bushes on the plot, you need to unscrew the nut of the working mount and install a cutting knife. Then tighten the nut firmly with a wrench.

3. Before starting work. It is very important to wear safety glasses when working with the trimmer, because even if you cleaned the area from debris, plant stalks and grass can fly into your eyes. The same stems, grass and branches can hurt your hands, so it is advisable to wear gloves. We simply plug the electric trimmer into the network, but the battery trimmer needs to be charged for several hours before work. Then, if there is a shoulder mount, hang it on the shoulder, knapsack. on both shoulders. Comfortably grab the trimmer by the handles. The D-shaped handle must be tightly wrapped around the palm of your hand, and the garden trimmer with the bicycle handle (U-shaped) should be firmly taken with both hands. The trimmer must be held above the grass so that the spool with fishing line or knife is parallel to the ground. Turn on the start.

4. How to mow. The rotation of the cutting mechanism occurs counterclockwise. Thus, in order for the cut grass to fall on the already mowed area, easily, with simple movements, we carry out the trimmer in front of us, from right to left. To remove the rest of the grass, you should make a movement to another side. from left to right. If the area is even and large, break it into imaginary squares and mow, moving along the outside of such a square. If the site is on a slope, then you need to start mowing from the bottom of the lawn, passing across the site. in one side. Having reached the edge, you need to go back and mow in the same direction, in parallel.
If there are a lot of trees on the site, mow only with fishing line, otherwise you can cut the tree trunk with a knife. In such a garden, it is best to mow around the perimeter, bypassing the tree in a circle.5. Shutdown. Turn off the engine and remove the shoulder straps. this is not a complete shutdown. It is necessary to carefully clean the spool and knife from the remnants of grass. Then fold the trimmer if it is telescopic or collapsible and hide it until the next mowing.

The fishing line also has its secrets.
The fishing line is wound around the spool inside the reel, and its tips are exposed. When mowing, the spool rotates, and the line, with this rotation, cuts off the grass. To release the tips you need to lightly tap the coil on the ground (semi-automatic system), there are automatic reels in which the fishing line is released by itself. When working with fishing line there are also several rules:

In order not to damage the fishing line and reel. Try not to touch the reel and fishing line of various solid materials. paths, borders, fences. From this fishing line is prematurely shortened, the coil may be damaged or even jam the engine. The spool with fishing line should also not touch the ground.

Mowing with tips is more efficient. If you mow the entire length of the fishing line, you can overload the engine. In addition, this reduces the efficiency of mowing. The tool must be held so that it mows only the ends of the fishing line. To do this, tilt it forward. towards mowing.

Tall grass requires several mowing. If the grass is above 20 centimeters, then one mowing will not do here. It is necessary to mow two to three times, from top to bottom. This is done so that the grass does not wrap around the reel. Wound grass is a guaranteed overheating of the engine. If the grass is still wound, you need to stop the tool and clean it.

The fishing line ran away and hid in a reel. This option when working happens if you did not release the line from the reel on time. After all, the line when mowing is erased and shortened. If you do not have time to release it, then stop the engine, turn off the tool from the network, and then disassemble the spool and pass the ends of the fishing line into the desired holes.

What does the consumption of fishing line depend on? It must be remembered that the line wears out faster if the grass is tough. Therefore, you need to release it more often when mowing weeds and dry hard grass. Around the foundation of the house, near the wall and the curb, the consumption of fishing line will also be greater than directly on the lawn or near trees. It is worth considering: if you work carefully and accurately, the consumption of trimmer line will be optimal and economical.

How to Wear a Patriot Trimmer Strap

A successful harvest requires a good harvest. To achieve it, you need the right technique. land care technique and the technique on which to care for the land. Therefore, the presence of a large number of home equipment and a variety of equipment is a sign that a person knows how to conduct business. But, any factory product costs money that can be spent on more important needs. A homemade cultivator can be made by resorting to buying parts for it only, in the worst case, when it is completely impossible to do it yourself, using improvised materials is physically impossible.

What is a cultivator

Cultivators, different designs, and different specifics of work, this is exactly the equipment that is rarely used, but brings great benefit.

Cultivation is on the list of priority tasks for any farmer, since it helps to prevent the appearance of weeds, at least in large quantities, helps to saturate the earth with oxygen, thanks to loosening.

It is not in vain that the most popular product drawings are a homemade cultivator for a tiller and a homemade cultivator hiller. They are relatively easy to make on their own, at home, so there are a lot of variations of schemes on this topic.

The principle of operation and the purpose of homemade cultivators is the same as that of the cultivators Patriot, Champion, Strizh, Texas, Viking, Cayman industrial production.

Next, we will consider the most successful and simplest options for homemade cultivators. Also see the articles “do-it-yourself tiller harrow drawings” and do-it-yourself tiller discs.

For more details on the cultivator, see the video:

Necessary materials

Among the materials that will be needed in order to manufacture any equipment presented in the list, first of all there should be profiles of all kinds and steel sheets.

Metal pipes of at least three diameters will make it possible to assemble strong and lightweight constructions, make long handles without fear of seriously shifting the center of gravity.

With the help of corners and channels, you can assemble excellent frames, in which there are initially niches for mounting various parts and details. Also, for work, you will need an angle grinder, a welding machine and a drill. Without quiet, the most popular tools, it will not be possible to assemble a single product.

How to make a hiller do it yourself

For t 16

One of the easiest tractor products is the cultivator. do-it-yourself for t 16 do it yourself it is done in just a few days, or even faster if you already have experience in similar work.

Such a cultivator does not need a special frame. a rather simple rectangular design with wheels on both edges.

Plane cutters are mounted on a small extension, about half a meter behind the center of gravity, and immediately behind them a small harrow is installed on a floating platform, thanks to which the loosened soil is further crushed, becoming softer.

Out of the bike

A homemade hand cultivator from a bicycle is great and cheap way cope with weeds that have flooded the garden and interfere with the growth of beneficial plants and crops. Making a hand cultivator with your own hands is simple, even at home.

With just a bicycle frame with one medium-sized wheel and a strip of high-carbon steel. To make a strong and reliable cultivator design, you need to install the rear wheel on the frame and fix it well.

If you turn the frame over, the pipe in which the saddle is mounted will face down. It is here that the plane cutter itself is mounted on a tripod, which is welded exactly in the middle of the metal strip.

The other part of the frame, the one where the carriage is located. now it is at the top, is equipped with long handles with a cross member and a stop, which are fastened to the frame by welding in two places, so that during work with the tool it could be applied, without breaking its parts and connections.

For tractor

To make good homemade cultivators for tractor, First of all, it is necessary to determine their size, since this is, in fact, the only thing that they differ in particular. It is clear that the greater the tractor power, the larger the cultivator.

In any case, it should have several main parts.

The following are installed on the frame: a mount made taking into account the mounting characteristics of the tractor, plane cutters that are supported by wheels and a harrow that can be installed as desired. But its presence is more than necessary to break too large clods of land.

How to Wear a Patriot Trimmer Strap

For inter-row machining

In the household, a homemade cultivator for inter-row processing is very useful. This item should be enough compact, simple and convenient in use, since it will be used for processing narrow aisles.

For this purpose, a hand-held cultivator Hedgehog is suitable, which is simply made with your own hands. you just need a handle, a U-shaped bracket with holes at the ends, a shaft and wheels with metal spikes.

The wheels can also be made independently, as one of the options, it can be small steel pancakes with welded steel spikes, which are made of reinforcement, sharpened in the shape of a cone.

Currently, special mini-class equipment has become very popular among land owners. A Chinese mini tractor is a very economical purchase for you for many years to come.

The manual potato planter is an indispensable assistant in your farm. Here is all about how to do it yourself and how to use it.

Video: How to Wear a Patriot Trimmer Strap


Here you can read about how many cubic meters of various materials fit in the Kamaz body.

These "milling cutters" of a manual cultivator are put on an axis, which, in turn, is attached to the bracket. its edges are fixed at the holes. The handle must be inserted into the mount welded to the end of the bracket. the inventory is ready for inter-row weeding and cultivation.

For mini tractor

To make a homemade cultivator for a mini tractor or for a tiller do it yourself square metal plates, 1515 centimeters in size, rectangular. 254 centimeters and a steel pipe. You need to start making a cultivator with cutters.

In order for the milling cutters to turn out reliable and suitable for processing all types of soil, and not only loose chernozem, they need to be assembled with bolts. holes must be drilled in the workpieces, the number of which depends on the size of the metal strips, which will act as blades.

The greater their length, the more holes are needed to secure them securely. Further, the strips are fixed on the workpieces, overlapping each other in a circle, and clamped with bolts.

For these compounds, you can also apply welding, but in this case they will not be strong enough, and repair and replacement of knives will be a difficult process. Welding is used here to join the cutters together. To do this, holes are made in the workpieces, the diameter of which must correspond to the outer diameter of the pipe.

Milling cutters are put on over it and are fixed with tacks, or short seams. This product can now be worn on the minitractor shaft and used as intended.

From a Chinese chainsaw

One of the most successful inventions and a good example of how to reuse old equipment is a makeshift cultivator from a Chinese chainsaw. Such a product will look like a miniature tiller, because their designs will not differ much.

The frame of the product is a cube, made of metal corners with an approximate size of 3232 centimeters. The engine must be mounted on the upper cross member of this structure. The fuel tank must be installed a little lower on the brackets.

On the front vertical struts of the frame, it is necessary to install mounts for the intermediate shaft. The bearings for the bearings of the running shaft are mounted on the longitudinal corners of the frame. The result is a mechanism in which the center of gravity is exactly above the supporting surface.

The weight of the product can be increased with the help of the load, moreover, by loading the mechanism in front, you will not shift its center of gravity. The control knobs are best made from pipes with a diameter of at least 30 millimeters, using a cross member, for greater structural rigidity.

To the frame to strengthen them is best in four places. Wheels for the mechanism you can use any but rubber-coated rollers are best suited.

From trimmer

Another way to use equipment with a low-power engine is a makeshift trimmer cultivator. Such a product is wonderful suitable for quick processing of small areas, and to make it from improvised materials is very simple. To do this, it is enough to make a cutter that will be mounted on the trimmer shaft.

The milling cutter can be made from the teeth of the pitchfork, bent in the desired shape, fixed to the base. a nickle with a diameter of about 10 centimeters. The base should be perfectly round, with a mounting hole located exactly in the middle.

The teeth of the pitchfork, sharpened, and pre-flattened to a width of one centimeter, are mounted on several bolts, in a circle, to the base. The finished mill copes well with loose soil at a shallow depth.

At MTZ 80

In order to make a homemade cultivator on MTZ 80, you need to stock up on patience and materials. The fact is that, unlike a simple trailed cultivator, this one should have special mount suitable for use on MTZ 80.

Otherwise, their designs are not very different. a rectangular frame made of square profile, to which plane cutters are attached in an amount of seven to eleven pieces. A pair of wheels attached between plane cutters, for stability and adjustment of the depth of capture of soil and harrow, fixed by chains over the edge of the supporting frame.

Mounting the cultivator with the tractor should be done so that with the help of the control mechanism it is possible to adjust its height and pressing force, without the risk of breakage or jamming of one of the parts, that is, exactly repeat the form of attachment of the factory attachments and MTZ 80.

With gearbox from vases

All those who planned to assemble a tiller with their own hands will encounter a certain problem, namely the types of gearboxes. All gearboxes installed on factory tillers are: cheap. they are non-separable models, and collapsible, which are much more expensive.

Regardless of which one you choose, the result will be the same, in terms of final cost. But you can compromise by making a homemade cultivator with gearbox from VAZ.

The difference in designs will be significant, and you may have to recalculate the rated power and transmission torque, starting from the characteristics of the VAZ gearbox, but as a result you will get a mechanism based on the work of a relatively cheap, reliable and easy to repair part.

In addition, all the parts that have failed can be found on any market, since VAZ cars are much more popular than any, even the best tiller.

Electric

One of the most practical and budget site processing solutions, this is a homemade electric cultivator. It is necessary to connect a reduction gear to an electric motor that is already fixed on the base. It can be purchased, or used second-hand.

Corners are welded to the crankcase of this gearbox, to which the wheel axles are welded. The wheels should not be small, because in this case they will dig into the ground. The handles can be made of two slightly curved pipes, between which a jumper is installed.

As a shaft, you can use scrap turned on a machine tool scrap, which is inserted in place of the hub of the gearbox. It is firmly and reliably fixed, after which cutters can be welded to it. Milling cutters, in turn, can be made from car springs. they are very strong and will last a long time.

Important tips and tricks

Starting to manufacture attachments and other equipment intended for cultivating the land, it is necessary consider some features production of products. If you personally assembled and launched a cultivator or hiller, it will be impossible for you to guess how it will behave on the ground during operation.

Especially if a tractor equipped with a homemade product has to work on different soils. Thus, a homemade cultivator for the T 25 may be too light, because it was assembled according to the scheme for the T 16 model, which has a lower power engine.

The same applies to equipment such as a homemade cultivator on the T 40. although this tractor has great power, it will not be advisable to put large equipment on it.

The work will be much more productive if the cultivator is not wider than the rear axle of the tractor, and in length not more than the width of the rear wheel.

In this case, he will be able to process a larger area, in a short time, with the same workmanship.

Conclusion

Although home-made equipment does not have a pleasant appearance comparable to factory machinery and equipment, in all other respects they practically do not differ, except for value.

Therefore, in order to successfully plow the garden, cultivate the field, or weed the beds, it is enough to just take the time to construct a convenient and practical product, practically using what lies under your feet.

Such a device will serve no worse than a stamped one under production conditions, but it will cost several times less. And this is the most important thing in things done by yourself. high quality products for a lower price.

How to Wear a Blade on a Stihl Trimmer

For work on a site and in a garden specific devices are often required. One of such narrowly focused on use, but useful tools is a garden electric delimbers. In fact, this is a secateurs with electric drive and long adjustable handles. The main advantages of the device:

  • The drive makes it easy to cut thick branches with a diameter of up to 10 cm;
  • Adjustable handles allow you to work at high altitude;
  • Labor productivity increases several times.

Types of Electric Loppers

  1. Electric delimbers. The handle is designed in such a way that muscle fatigue does not accumulate in the hands. Thanks to the pulley integrated in the handle cavity, it is possible to activate the action of the gear mechanism at high altitude and remove branches 3-4 cm thick in 2-3 steps. The optimum height is 4 m. For operation at heights of up to 6 m, the electric knife cutter is connected to an additional rod.
  2. The telescopic high-rise garden delimber is convenient because it is quite compact and convenient to store when folded, and when unfolding it allows you to work at high heights (up to 6 m) with a wide radius. The gardener drives the ratchet mechanism with a lever on the handle. The ratchet makes the cut very precise and even. On more advanced models, the kit comes with an electric saw.
  3. Electric delimber for working with low branches. Visually, the tool is a traditional secateurs with short handles. There is a start button on the handle. The branch is placed between the edges, the button is pressed, and the chain saw quickly and effortlessly makes a saw cut.

Features of use

  • Working with an electric delimbing knife is much faster and more efficient due to the convenient design of long handles. Applying physical force to remove branches is not necessary. It is enough to hold the branch between the blades and start the mechanism that will close the blades with each other.
  • The second feature of use is the type of blade:
  1. Plane. work similarly to the scissor mechanism. The branch is clamped between the blades and removed with a cutting action;
  2. Contact. are located on the same plane. The branch is located at the junction of the blades and is removed by compressive action.
  • A prerequisite for use is the availability of power. Therefore, in advance it is worth taking care of the purchase of adapters, extension cords and other necessary devices for connection. If access to electricity is limited, then you should buy a battery-powered device. It is more mobile and does not need constant access to electricity. However, the electric delimber is much more powerful than the battery delimiter, but inferior to gasoline.
  • Manufacturers also took care of the safety of the tool, so almost all models are equipped with a protective mechanism against accidental switching on.

Pros and Cons of Electric Knife Cutters

Choosing an Electric Cutter

Determine the need to purchase the device, depending on the purpose. It is worth considering what type of trees will be pruned. Young shrubs and trees with thin branches and soft wood are best trimmed with planar tools. No great effort is needed, so a little pressure effectively removes young thin branches. Mature trees with thick branches and hardwood, as well as dry branches, are cut with contact blades. In this case, it is very important to maintain the integrity of the cortex. Under the influence of pressure, it can crack, so a clear cut is needed. It can be achieved using the scissor mechanism.

How to Wear a Blade on a Stihl Trimmer

On a note! In addition, when choosing a lopper, it is worth considering who will work with this tool. If the weight and dimensions of the device are not very important for a man, then for women and the elderly these parameters are important. Another important point is the presence of an insulating handle. This allows you to safely work in conditions of high humidity or near electrical networks.

Video: How to Wear a Blade on a Stihl Trimmer


Browse Popular Models

Husqvarna / Husqvarna. delimber from Sweden. The most popular model for professional use. 525РТ5S. Thanks to the telescopic bar, you can instantly adjust the height. Very mobile and maneuverable tool. The engine is rapidly gaining momentum. The case is equipped with shock protection from below and behind. Automatic lubrication of the chain. The weight of the device is 7 kg. Price. 44000-50000 rubles.

A popular budget option is the Ryobi RPP750S. An adjustable three-stage boom allows you to work at different heights. The handle design is very comfortable to grip. In addition, there is an insulating rubberized layer of Gripzone. A locking belt is supplied with the delimbers for operation at low heights. This instrument has a low noise level and compact dimensions. The maximum diameter of the branch grip is 20 cm. To facilitate work with the tool, the saw is at an angle of 15 °. Oil is supplied automatically; to monitor the oil level, the tank is made of transparent material. Price. 7500-8000 rubles.

Bosch Brush Cutter (BOSH) AHS 45-16 is a very compact unit (only 2.6 kg) for small garden areas. The engine is protected against overheating thanks to the integrated ventilation system. The handle is designed taking into account the anatomical features, a screen is installed to protect the skin. To speed up the work, a double-sided knife with built-in protection against collision with hard obstacles is installed. The knives are sharpened by lasers, so the cut quality is very high. Price. 4300-4600 rubles.

To work in an urban environment, the NTE60 delimber from STIHL was developed. First of all, the tool differs in full compliance with sanitary standards in terms of permissible noise level (within 94 dB). This is a universal tool for sanitary trimming and use in landscape design to form a decorative crown. The length of the working surface is 0.3 m. Smooth on and off helps protect the engine from sudden jerks. Ergonomic design allows you to clearly lock the tool in your hands. A belt is provided for additional fixation. Weight. 4.5 kg. Increased torque allows you to cut thick branches. Price. 19000-20000 rubles.

Brush Cutter Black&Decker BEHTS301

Electric brush cutter BLACK&DECKER BEHTS301. a budget tool for the refinement of decorative hedges. Suitable for branches with a thickness of 3.5 cm. Has 2 handles for complete control over the movement of the blades. The start button occupies the entire length of the handle, which makes it easier to turn on. There is protection against accidental startup. The handle has a hand shield. You can cut branches in any direction due to a double-sided knife. Eco-friendly, manoeuvrable device weighing 2.46 kg. Price. 5400-5600 rubles.

The CARVER HT 5560E Electric Brushcutter is a tool for shaping compact shrubs. The maximum thickness of the cut branches is 2.5 cm. Diamond grinding allows you to make a high-quality even cut without injuring the plant. System of protection against pulling the cord from the network. For ease of storage and safety of blades, a protective cover is included. A hand shield is installed on the handle. There is an additional holder for better fixing the brush cutter in the hands. Weight. 4.4 kg. Price. 3300-3500 rubles.

Rules of operation and care

  1. Assembly and adjustment is carried out strictly according to the instructions, each part must be tightly fixed in place;
  2. Before starting the main work, it is recommended to make a trial cut to make sure the assembly is reliable;
  3. Before trimming, you must wear a protective suit made of thick fabric, protect your eyes with glasses, put gloves on your hands. Take a stable position, hold the tool firmly and confidently;
  4. Bring the blades to the branch and set so that the cutting blade is located exactly on top;
  5. Drive the mechanism and cut the branch;
  6. When trimming low branches, the delimbers are fixed using a special belt that is thrown over the shoulder. At the same time, a pocket for installing the delimbers should be in the abdomen;
  7. At the end of the work, the blades must be thoroughly cleaned of chips, dirt, dust. Inspect the inside of the tool and clean if dirt is present. Lubricate parts with small;
  8. Storage of the tool is permissible only in a dry, dark place.

Electric tree delimbers significantly facilitate gardening, especially at high altitudes. Thanks to this device, you can easily form a crown and remove old or diseased branches. When buying, pay attention to the manufacturer. A well-known company with many years of experience will be a guarantee of reliability and durability.

How to Wear a Trimmer Strap

How to mow grass with a trimmer?

The main thing is to correctly adjust the trimmer belt so that the drum with fishing line does not crawl along the ground.

Properly make a gasoline-oil mixture.

Do not use too thick fishing line. it picks up speed and overloads the trimmer.

Do not be afraid to give him speed.

Do not wind too much fishing line on the drum, and do not wind it too much.

Stop from time to time and empty the basket.

Lubricate the trimmer cable and gear (if any) with a grease gun.

the author of the question chose this answer as the best

The technique of mowing grass with a trimmer is not very complicated and takes into account the need:

  • Decide how exactly you are going to mow. It is possible to fold, crosswise.
  • choose a place so that a bald spot does not appear as a result and the site looks harmonious
  • understand what exactly you are going to mow, and depending on the choice to put the right knife. They are different. For example, hay or weed. You also need to set the speed.
  • Of course, it is necessary to prepare both clothing and protective equipment. Whatever you are an experienced mower man, but glasses must be worn. and don’t forget the headphones and long clothes.

All the details of the technique are on the video how to mow with a trimmer.

add to favorites link thank

First of all, inspect the area that you have to mow. Cut yourself bushes or large flowers that cannot be cut.

Always start with a light area where there is little grass. See if there are slopes or ditches in the area. The easiest way to mow across the slope.

Determine the direction of the grass. Mowing is easier if the grass is tilted forward.

As for clothes, you should always wear glasses and boots. Also anti-vibration gloves do not interfere.

Depending on the density of the grass, use different knives.

One more tip: try to mow at the same speed. This way your mower will last longer. If you stop and immediately pick up speed, then the trimmer will wear out faster.

Correct mowing with trimmer:

  • choose the fishing line correctly. For different tasks, there are two different subjects. fishing line and knife. Too wide fishing line is undesirable, as this will give overload to the trimmer. As a rule, on a simple site fishing line is enough.
  • when cutting is installed (fishing line or knife), it is necessary to tighten and fasten the nut.
  • Check the charge or availability of fuel. Put on the belt comfortably.
  • movements when mowing with a trimmer should be thought out. The algorithm is: right-left-left-right. This will give the maximum result. Yes and be attentive to work. It is necessary to control that there are no children or animals near you. You should also wear a mask to protect your eyes.

add to favorites link thank

First, adjust the trimmer belt so that the drum does not touch the ground. Further, it is important to remember that due to the thick fishing line, the trimmer will be overloaded, so do not overdo it with the thickness.

A lot of fishing line on the drum is not worth winding.

Remember to periodically clean the trimmer.

Lubricate the cable with grease necessarily.

The trimmer is very convenient as it can be used in a variety of places, including complex terrain and areas near trees. If you mow tall grass, first start with the protruding tops and then continue with the bulk.

add to favorites link thank

Use the trimmer as intended. An electric scythe (that is, a trimmer) is good because it copes well with its work in hard-to-reach places. Therefore, the trimmer can be used near trees, fences in relief areas. And not only for mowing the lawn, but also ordinary grass.

The main thing. this is to ensure that the weeds do not have time to give the seeds and mow them in time.

If you did not have time to mow the grass before the moment when it gave the ears, then first mow the tops of the ears and burn them. And only then mow the grass itself, and put it into compost.

add to favorites link thank

In almost all trimmers (if there are no special ones), the fishing line or the disc rotates clockwise. That is why it is better to mow the grass with a movement from right to left (a movement that resembles movement when mowing with an iron scythe). It can be mowed by tilting slightly towards mowing.

You need to mow with calm movements, not jerks. Mow grass half the length of the fishing line. If you grab more, the trimmer can handle it, but grass can clog the space between the coil and the pipe.

Mow, squeezing the gas to full.

add to favorites link thank

Before mowing the grass, first adjust the fishing line and firmly fix it in your cavity so that the fishing line does not hang out and go there. here. Then fill the fuel accordingly (if you do not have an electric trimmer) which consists of special oil and gasoline. Next, start mowing the grass with smooth movements (not fast) to the right and left. Do not try to chop thick stems of plants often, as the fishing line will instantly end, and you will have to adjust the reel again. In dense places, the main thing is not to spare gas)

add to favorites link thank

Trimmer from the company Varyag koshu according to the instructions:

Step 1. Install the cutting mechanism.

Depending on the type of weed grass, we choose a cutting tool: for soft-stem grasses. fishing line, for hard-stemmed and small shrubs. knife. Unscrew the nut securing the cutting mechanism and install the cutting tool. Tighten the nut. the mechanism is ready to work.

Note: some trimmers do not have interchangeable cutting tools, so you can start working with them right away.

Step 2. Preparing the trimmer for work.

If the trimmer is electric. charge the battery or turn on the motor in the network. If gasoline. refuel the tank with fuel. Then, depending on the type of trimmer. we adapt it to ourselves (upper-motor. is hung with a loop on the shoulder, knapsack. for the shoulders, lower-motor. we take the handle). We hold the trimmer over the grass so that its cutting mechanism is parallel to the treated area. We start the engine.

Action 3. Mowing.

Grass mowing with a trimmer is carried out with simple movements. It is important to remember that the cutting mechanism of the device rotates counterclockwise, so that the mowed grass will fall on the already treated area. The first is from right to left in front of us (this is how we cut off the top of the grass). The second is from left to right (this is how we remove the rest of the grass).

It is better to divide a large area of ​​the cultivated area into squares, and mow grass on them, moving from one to another on the outside of each square.

When mowing grass on the slopes, it is recommended to mow from below, moving parallel to the sloping area. We reached the edge, went back, became a little higher. and we repeat the same route. until the site is completely mowed.

For mowing grass in the area where there are trees, it is better to use a forest cutting mechanism, and you need to mow, passing the site along the perimeter, bypassing the tree around the trunk.

Step 4. Finish the job.

Video: How to Wear a Trimmer Strap


After mowing all the grass in the area, you need to turn off the engine, remove the trimmer (for shoulder and knapsack devices), clean the cutting mechanism of the rest of the grass.

»How to configure

How to properly configure the brushcutter belt for yourself

author: fazenda | June 2 | Views: 10082

Service center specialists often complain about consumers of household gardening equipment who, even at the stage of their assembly and first start-up, make mistakes and disable equipment. Of course, there is an instruction in the package, but either it is stupidly written, or it is read after improper assembly, when extra details were discovered or, worse, a breakdown occurred. Meanwhile, there is nothing complicated in the assembly of household gardening equipment. You just have to be careful. Let us give an example of the assembly order of the Stihl FS 130 petrol scraper, complementing our instructions with illustrations.

1. The assembly must be started by opening the box and checking the complete set of the unit. If everything is in place, then we have to fasten the handle to the rod with the motor, put on the belt, attach the protective cover and cutting elements.

2. First you need to remove the handle and unscrew the thumb screw that secures the upper part of the support without losing the springs.

3. Insert the handle into the socket and fix it without tightening it much. The final position will be adjusted after the final assembly of the brushcutter.

4. We put the control handle of the unit on the handle tube and tighten the fastening bolt. To do this, the kit has a universal key.

5. All Stihl FS 130 brushcutter controls are located on the handle. These are: the throttle lever, which has protection against accidental switching on and the lever for turning off the unit, which is controlled by the thumb. The modification of the lawn mowers with a D-shaped handle controls are located next to the engine on the bar.

6. We put a plastic protective cover. If you plan to use only a knife, then for its work we use a part of the casing (in the picture it is painted in orange).

7. If there is work to be done with a cutting line, then a plastic skirt is additionally put on the protective cover of the chainsaw and a knife for cutting the line is placed. In some varieties of this model, the cover can be universal or two different covers can be attached. one for the fishing line and the other for the knife.

8. Sliding the skirt over the casing, check the reliability of its fastening. Sometimes it may be necessary to fix this protection with another screw.

9. Now you need to put the knife for cutting the fishing line and fix it with a screw.

10. It remains to install the reel, pre-filling it with fishing line. The coil is screwed onto the shaft (as in the illustration) or fastened with a special nut. Keep in mind that the thread on the shaft is usually left. How to fill the fishing line into the reel, read the instructions.

11. If a knife is required, then we put it instead of a coil. The knife is equipped with a protective cover so that during operation it does not dig into the soil. After installing it, do not forget to scroll this cutting element and make sure there is no play.

12. Well, the last, simplest step is to install a metal clamp on the rod, i.e. fastenings for a suspension belt.

After the brushcutter is assembled, we put on a shoulder belt or a belt knapsack suspension (depending on what is included in the kit) and customize them according to the figure. Fill the gasoline mixture, start the engine. and forward.

Trimmer belt How to adjust the trimmer knapsack belt

1. Adjust the height of the trimmer belt hook tightening the shoulder straps so that the trimmer knife lowered to the ground is parallel to the surface of the plot (strictly horizontal).
When operating the trimmer saw blade, adjust the height of the hook (by lifting the shoulder straps) so that the trimmer blade is tilted slightly forward relative to the ground.

2. Moving the ear to hang the braids on the trim tab forward or backward, balance the trimmer so that when releasing the steering wheel the trimmer knife is near the surface of the site, but does not lie on the grass.
For sawing bushes and young trees with a saw blade of a brush cutter, the trimmer must be balanced so that when the steering wheel is released, the machine hangs horizontally on the hook horizontally. Attach.

3. Adjust the trimmer shoulder straps (harnesses of the harness) so that the load is distributed evenly over the shoulders (check by hand pressing the hook of the trimmer suspension).

Video about the Husqvarna trimmer backpack. On the design features of the belt suspension (harness) that make mowing the lawn mowing, trimmer, bender, Husqvarna brushcutter easier and safer. wide shoulder straps and an elastic waist belt, quick-release locks (carbines) in case of fire or any other situation requiring quick release from the trimmer. On the versatility of belts for men and women.

Such Husqvarna trimmer knapsack belts (Balance 35/55, Balance X, Balance XT) can be used on any trimmers, lawn mowers, lawn mowers, electric braids, brush cutters.

Share link:

Post navigation

Recent comments

Subscribe to the site

How to Wear a Trimmer Strap

Teeth properly cleaned food after

When to brush your teeth: before breakfast or after? Surely everyone knows that you need to brush your teeth twice a day. Imagine morning without

Watch how to brush your teeth

How to brush your dog’s teeth at home Hello! I Kulkova Nadezhda Petrovna, senior veterinarian, specialist in veterinary dentistry

See how to clean pomegranates

How to clean the pomegranate from the peel. Video Description: There is a custom in hot and sunny Georgia: if a young man is in love with a girl,

How much to brush your teeth

Brushing Teeth Correctly Currently, there are both general and individual recommendations regarding the correct brushing of teeth and oral cavity. And the question is, how long does it take to clean

Interesting

The right trimmer belt

There are trimmers for which additional accessories are not needed. for example, lightweight battery-powered trimmers. Even a child can carry them, and they firmly lie in his hand, not breaking out. However, most often trimmers weigh from 6 to 9 kg, and in order not to get tired of moving them from place to place, you need a belt.

Why else do I need a trim belt?

1) To transport the trimmer. Transporting a trimmer to the cottage when there is no car is a complicated matter. If the equipment does not have a belt, then at least a cover with a belt should be sewn over the shoulder. This will ease the load when transporting the trimmer.

2) For convenient mowing of grass. After all, if your hands get tired, then you will not want to mow the weeds and the overgrown lawn. And if you want, then trembling hands from fatigue is an unsafe option.

3) For the ergonomic position of the trimmer relative to the body. Correctly fastened and adjusted along the length of the belt to protect against lower back injuries and overstrain of the muscles of the back.

4) For security. The trimmer will be much safer if it decreases the likelihood of it slipping out of your hands when branches and hard vegetation get into the cutting head. When this happens, the trimmer, whether it is a petrol or electric scythe, makes a sharp jerk, and the trimmer literally "breaks out" of the hands.

For these reasons, many models of garden trimmers equipped belts. They are threaded through the trimmer shaft and mounted over the operator’s arm. The belt helps balance the total weight of the trimmer and the operator, and you don’t have to balance the balance by stretching your arms or putting one leg back.

How to attach the belt to the trimmer?

1) Find the place where the belt fastens to the trimmer shaft. On many models designed for amateur gardeners, a hook, screw, or groove is located next to the ignition handle or toggle switch.

2) Squeeze the carabiner belt and hook it on the eye on the trimmer handle. Find the second belt hole and do the same.

3) Throw the trimmer with a belt over your back so that the upper part of the belt goes over the left shoulder (for left-handed people. over the right one).

4) Adjust the length of the strap so that the lever, which is responsible for mowing power and continuous mowing, is at a convenient height of the arm slightly bent at the elbow. In width it is necessary to ensure that from the body to the trimmer was at least 10-15 cm.

5) Put your right hand on the lever and the left hand on the top panel. Move the head of the trimmer, feel where the center of gravity is located at the trimmer. If the weight is still unbalanced and you have to bend over, or you make an extraordinary effort to hold the device, try pulling the belt higher or lower by 1-2 cm. After you have completely dealt with the belt, you will feel what position with the trimmer most comfortable

6) Stop cutting grass if you have pain in the lower back and arms. Adjust the belt again.

What should be the trimmer belt?

The leather belt is best suited for the trimmer: it does not slip and fixes the equipment quite rigidly, and the skin is pleasant to the touch.

In the area of ​​the shoulder, you can make a special quilted pad that will make the shoulder load less noticeable and reduce friction.

Remember that a correctly selected belt for the trimmer is essential will increase comfort and speed with this garden equipment. This means that health, mood and lawn will be in perfect order.