The Better to Cut Plastic PVC Panels

Jigsaw

Allows you to cut along and across multiple sheets at once. The tool has the advantages of a hand tool, but when using it, the employee is much less tired. However, due to the speed of movement of the teeth, it is extremely difficult to do curly cutting with it.

You need to work at minimum power so that the plastic does not deform from heating. If the tool is hot, you need to stop and wait until it cools down.

better, plastic, panels

How to properly cut plastic panels for wall decoration

There are many types of finishing panels for interior and exterior work. The cladding is easy enough to cut, saw and fasten, as it is designed for quick and easy installation. However, each material has its own characteristics.

Circular

The circular saw is also designed to handle large volumes of material. The tool provides a perfectly smooth cut of several sheets at once. Cutting in any direction is allowed. For sawing, you need to take a special disc for plastic or a model for soft wood, plastic and aluminum.

angle grinder

An angle grinder is not very suitable for cutting panels: the rotation speed of the disc is very high, the material heats up during operation. Therefore, they take low-power models and the thinnest disc. 0.8 or 1 mm. A definite plus: a thin and precise cut regardless of plastic temperature and weather conditions. an angle grinder can cut the cladding in the cold. Negative: emits a lot of dust.

Things to Consider Before Cutting

The panels must not be overheated or cut at sub-zero temperatures.

Before cutting PVC panels, take into account:

  • Low resistance to heat. plastic is not designed for operation above 50–60 ° С. At a temperature slightly above 100 ° C, it begins to melt and deform. Therefore, tools that heat the material must not be used for cutting.
  • Working conditions. as the temperature drops to 0 ° C and below, the plastic becomes brittle. Cutting plastic panels during winter work must be extremely careful. It is advisable to cut in a room where the temperature is higher. Before installation, the panels are taken out into the shed or under the shed so that they adapt to the cold. In this case, the increased fragility does not matter anymore.
  • Dimensions. the standard length of the facing sheet is 3 m. Working with such large panels is inconvenient. However, in addition to the usual cut along or across, a shaped PVC cut will be required. To do this, you need to choose a tool that is more maneuverable.

The material has a uniform structure, so it can be cut in any direction. It is important to find the right tool.

Tools for cutting panels without defects

To adjust the length or width of a pair of lamellas, a simple hacksaw is sufficient. But if there are a lot of sheets, it is worth choosing a more powerful tool.

2 types of cutters are used.

  • Mechanical. cutting is done with physical effort. The speed depends entirely on the capabilities of the employee. This method is preferable for curly cutting, as it requires patience and accuracy. Mechanical include hacksaws, knives, cutters, hand jigsaws.
  • Power tool. the worker guides the cutting blade, but does not exert his own efforts. In this way, many more panels can be cut. Representatives of the category: circular electric saw, angle grinder, jigsaw.

Hand tools are cheaper to use. Electric requires a connection to the network, but it is much more efficient.

For cutting, they take a clerical, construction and even kitchen knife. The best option is the construction one, as it is better balanced for this kind of work. When using stationery, for example, you will have to cut under an angle, which is not very convenient.

A paint knife is most suitable for cutting along 3–4 sheets. He has a very thin and sharp blade, the cutting line is also thin and neat. However, it will not work to cut across the lamellae with a molar knife.

Hacksaw

A hand saw is ideal for the job. the cutting line is thin, without chips, since the small teeth do not grab the fiber. You can cut along and across, diagonally, since the speed here is determined only by the applied forces, the risk of thermal melting of the panels is extremely small.

Features of PVC panels

PVC-panels, depending on the thickness and structure, are used for external cladding and for decoration of premises.

Panels are made by extrusion: raw material is poured into a special injection mold. a die, under high pressure. a melt of polyvinyl chloride. The initial mixture also includes other additives, for example, ground natural chalk, coloring pigments, plasticizers.

Additives provide the material with its properties:

  • high water resistance. not afraid of steam, water, snow;
  • chemical inertness. does not react with household chemically aggressive substances;
  • electrical insulating properties. plastic does not accumulate electricity;
  • elasticity and some elasticity. with low mechanical strength, this quality allows it to withstand the load and not deform;
  • durability. up to 50 years;
  • decorativeness. panels reproduce any color and texture of any natural material.

It is not only the shade that gives the product an attractive look. interesting is the option with thermal printing. In this case, the pattern and structure of the panel is provided by a thermal film. On a special machine, the film is rolled with a hot roller and pressed. The film adheres firmly. Such lamellas do not need to be varnished.

Offset printing also creates texture. But at the same time, the panel must be varnished.

Cutting rules

To carry out work safely, you must clearly follow the following rules:

  • When working with panels that were brought in from the cold, you must wait a short period of time. This action is necessary in order to warm the material. If you do not heed the advice, then the plastic panels will break during the cutting process, thereby losing their neat appearance. Often there are cases when cracks appear on the surface that is cut along.
  • In order to obtain several planks of the same length, it is necessary to lay them on at least 2 supports. Thus, protection against sagging or displacement occurs. It is recommended to abut the edge of the element that is not pruned against the wall. Thanks to this action, you can secure against their shift.
  • You can make the process easier by marking with a pencil or felt-tip pen.
  • It is necessary to cut correctly with the wrong side of the panel down, because during processing under the influence of the load, the profile of the strip changes and causes some inconvenience during the installation process. Microcracks often appear on the front surface, which appear in the future.
  • When using a power tool, you must use protective goggles and gloves that can protect against debris and sawdust flying in different directions during the cutting process.

Cutter

Experienced craftsmen, who have in their arsenal a whole range of special tools for processing plastic, are used to cut PVC panels for wall cladding with a special cutter. This useful tool makes an absolutely straight cut on plastic without the use of physical effort.

Craftsmen may well make that tool with their own hands according to the following instructions:

  • It is necessary to take a strip of metal sheet with a thickness of at least 2 mm. The width of the strip should be 1 cm.
  • One edge of the metal strip is cut at a 45 degree angle.
  • One side of a homemade cutter is sharpened with a whetstone.
  • The opposite side is wrapped with electrical tape so as not to damage the hand during work.

Note! A cutter for plastic costs 700-1500 rubles, it may well come in handy in the future. We advise you to purchase this useful tool, as it significantly speeds up the process of cutting PVC panels.

Molar knife

The easiest PVC cutting tool. But an unusual kitchen or shoemaker, here you only need a molar knife.

Its blade, while new, is very thin and sharp. And when it gets dull, the blade can be replaced instantly. By biting off a piece or inserting a new one. An ordinary knife is inconvenient, it cannot be sharpened quickly. Also, it won’t be so thin.

The molar knife is limited in scope. You can cut the panel with it only along. Of course, you can try to make a cut and across. But nothing good will come of it.

How to cut panels lengthwise? This is difficult to explain within the framework of the article. However, the basic principle can be described.

The blade extends a short distance of 3 mm.

From the back side of the panel, select the place where the cut will be made.

Then we cut out a strip, from edge to edge (we are talking about the inner edges of the panel). A cut is made near the rib, then another cut is made near the adjacent one. We make cuts along the entire length.

A strip of plastic falls out, a groove forms.

Then, on the same back side, you need to make a shallow incision near the desired rib. And over it to break the body.

The molar knife has advantages: speed, noiselessness and simplicity. And its disadvantages are that the panels can only be cut along.

Hacksaw

A hacksaw is a versatile tool that any craftsman has in his arsenal. It can easily cut plastic wall panels, if it is not possible to purchase a special cutter. With a hacksaw, the cutting process takes longer, but with a small amount of work, this does not significantly affect the duration of the wall cladding.

When sawing plastic with a hacksaw, the following nuances must be taken into account:

  • For sawing PVC, use a fine-toothed tool for wood (cross-cut) or metal.
  • Sawing plastic does not require strong force, otherwise material may be damaged.
  • With a hacksaw, you can cut several panels at once, folding them in a stack.

Please note that when processing plastic, the cut can turn out to be jagged if you use a tool with teeth set in different directions.

Panel slicing rules

If the panels have just been brought from the street, especially if there is a low temperature, in this case, you cannot immediately start working. For some time they need to warm up, since cold they become even more fragile and you can easily harm the material.

Before you start cutting, you need to note where the cuts will be. A felt-tip pen is best suited for these purposes. It is clearly visible on the panel and can be easily erased later.

During work, one should not forget about safety precautions, it is better to wear gloves and glasses. The thing is that, breaking, the panels form very sharp fragments, and there is a danger of being injured by them.

And in general, this material is very fragile, so you need to work with it very carefully and carefully.

Therefore, if someone else asks himself: “What is the cut of plastic panels?”. then we can safely say that there are many options. And surely in the end there will be the most suitable.

How to properly putty the wall video

Application of panels

In the process of sheathing, it is necessary to initially decide on the tool used for cutting the plastic panels. This material is widely used for finishing balconies or bathrooms, because it has an excellent set of properties. It is also impossible to forget about its practicality, which makes it even more popular. Plastic panels also attract buyers for their low cost and excellent appearance.

Each owner can independently finish the bathroom at home and at his discretion, because there are a huge variety of panel options that can be used for this. All PVC panels are manufactured with a standard length of 3 m.This is not always practical because it needs to be cut into pieces to obtain the desired size.

There is one secret

When you have to harvest a lot of sticks, frame size. For example, you need to cut off 20-30 pieces at once.

And so as not to cut one thing at a time, but to increase the speed. You can resort to one secret.

You will need clamps (bench presses) as in our photo. Take several at once, usually 5 pieces. Adjust them so that they do not stick out each other and clamp them with bench presses. Two on each side of the panel.

And calmly saw. In this way, you can cut up to 5 panels at a time. You can cut more, but a Bosch file does not provide this opportunity.

You will speed up the cutting process five times and make your work easier.

Cutter

This device is used by experienced craftsmen who are professionally engaged in finishing work.

The use of a cutter provides a perfectly smooth cut and allows you to shorten PVC strips without much physical effort.

Having bought such a tool, you can be sure that there will be no problems with high-quality cutting of panels.

The better to cut?

Different tools can be used to cut the panels. These include both special professional devices and ordinary hand or electric tools used in everyday life for various purposes.

Facing surfaces with PVC panels is a finishing method that many people choose today as the most optimal. It’s fast, simple and relatively inexpensive.

But in the course of the work, the question always arises: how to cut the PVC panel? Several methods are possible here, after considering which you can choose the most acceptable option for yourself.

Jigsaw and angle grinder

Using a jigsaw is a quick, but not too high-quality way. It is unlikely that it will be possible to achieve a perfectly even cut with its help, moreover, chips often form along the edge of the panel, so it is best to abandon this option, giving preference to the same angle grinder.

Using this tool will ensure an even cut, but only due to high speeds, the panel begins to emit an unpleasant odor and poisonous substances.

Hacksaw

This tool is present in any home workshop. For those who are not ready to spend money on purchasing a cutter, using a hacksaw may well be an option for solving the problem of cutting panels.

Yes, this method will take a little longer, but with a small amount of work, this will not greatly affect the period of wall cladding.

It is important to note that a hacksaw for metal is best for cutting panels, and if you use a tool for wood, then the blade should have fine teeth. for cross-cutting.

PVC TRIM VS. WOOD TRIM? (Pros And Cons!)

Although this tool is the least suitable for cutting PVC products, one or two strips can be cut in case of repair and replacement of panels. But with large-scale work, it is impractical to use it. the process will take a long time and painfully;

It is often used for cutting panels. Using a square or a flat wooden plank used as a ruler, it is possible to achieve an even cut.

What are they made of??

The raw material for PVC wall panels is polyvinyl chloride, which is poured into a die (casting mold) under high pressure.

This method is called the extrusion method. To add color, ground natural chalk is added to the composition of the material, the amount of which is, as a rule, no more than 40%.

In addition to coloring, panels are decorated using thermal printing or offset printing, but the latter method is used less often, due to its higher cost.

Thermal printing is applied on a special machine using a hot roller, which presses the thermal film to the surface of the product. Thus, it is possible to achieve fast transfer of the pattern and a clear and bright print, and the panel itself does not need to be varnished, in contrast to the use of offset printing.

You may be interested in an article on how to decorate a bathroom with plastic panels with your own hands.

How to cut PVC panels correctly?

To obtain a high-quality result when cutting, certain rules must be followed. Among them there are both general instructions and recommendations for working with a specific tool:

  • It is unacceptable to work with material that was brought in from the cold. it must be warmed up before opening. Chilled PVC becomes brittle, leading to edge chipping.
  • Wall panels should only be cut from the front side. Otherwise, the profile will crumple, and difficulties may arise during the installation process.
  • The use of an angle grinder, jigsaw or hacksaw allows you to cut a bundle of panels at once.

In this case, they must be laid on two supports so that they do not sag, and not the cut edge must be resting against the wall. this will prevent the panels from moving during cutting.

When using a power tool, it is advisable to wear protective goggles, since the likelihood of shrapnel falling into the face during operation is quite high.

When working with a knife, it is worth using a guide on which the tool will rest during cutting.

This, as already mentioned, can be a square or a wooden lath. The guide is applied to the cut mowing line, the panel is cut and cracked, after which the material is cut from the back side.

That’s all. The main methods of cutting PVC panels have been considered and it remains only to decide on the most optimal option, the choice of which depends on the personal preferences and capabilities of the master himself.

For a convenient way to cut PVC panels with a hacksaw, see the video below:

Hacksaw

A hacksaw is considered more practical to use, and it does not matter whether it is for metal or for wood. The only requirement when using a hacksaw for wood is the presence of small teeth, which should not be divorced, because this way the surface of the material that needs to be cut into pieces is destroyed. Such a tool is often used for crosscutting.

The advantage of this tool is the ability to cut multiple panels at the same time. For this operation, you will need to stack the material.

For convenience, when cutting, it is better to have the planks facing the contractor. When subjecting the length of the panels to a decrease, care must be taken not to apply enormous forces when pressing the tool, because this can break the PVC sheets.

Due to the plasticity that the material possesses, it does not take much effort to cut off the excess part of the panel.

Currently, a huge number of tools have been created, thanks to which it is possible to shorten the length of a particular material. When working with plastic panels, it is necessary to take into account many factors, among which the main ones are practicality, cutting speed, surface quality, as well as ease of use.

Cutting rules

To carry out work safely, you must clearly follow the following rules:

  • When working with panels that were brought in from the cold, you must wait a short period of time. This action is necessary in order to warm the material. If you do not heed the advice, then the plastic panels will break during the cutting process, thereby losing their neat appearance. Often there are cases when cracks appear on the surface that is cut along.
  • In order to obtain several planks of the same length, it is necessary to lay them on at least 2 supports. Thus, protection against sagging or displacement occurs. It is recommended to abut the edge of the element that is not pruned against the wall. Thanks to this action, you can secure against their shift.
  • You can make the process easier by marking with a pencil or felt-tip pen.
  • It is necessary to cut correctly with the wrong side of the panel down, because during processing under the influence of the load, the profile of the strip changes and causes some inconvenience during the installation process. Microcracks often appear on the front surface, which appear in the future.
  • When using a power tool, you must use protective goggles and gloves that can protect against debris and sawdust flying in different directions during the cutting process.

How to cut PVC panels: tool selection

Undoubtedly, tiles are considered to be a classic material for finishing a bathroom, however, PVC panels have an increased installation speed, and additional care of this material is not required, because neither soap nor water is deposited on their surface. Initially, plastic panels worked well due to their ease of installation. To carry out such work, you will not need help from specialists and a complex tool.

Cutter

This tool has proven itself well due to its low cost. Perfect for home use.

The tool has excellent performance and the cut surface looks smooth. It should also be highlighted the fact that it does not require much physical effort to carry out the cutting. A huge advantage can also be called its compactness, in which it does not take up much space during its storage.

The disadvantage of the tool is the ability to cut only in a straight line of the mowing line, they cannot round off the edges.

Application of panels

In the process of sheathing, it is necessary to initially decide on the tool used for cutting the plastic panels. This material is widely used for finishing balconies or bathrooms, because it has an excellent set of properties. It is also impossible to forget about its practicality, which makes it even more popular. Plastic panels also attract buyers for their low cost and excellent appearance.

Each owner can independently finish the bathroom at home and at his discretion, because there are a huge variety of panel options that can be used for this. All PVC panels are manufactured with a standard length of 3 m.This is not always practical because it needs to be cut into pieces to obtain the desired size.

Jigsaw, circular and angle grinder

These tools significantly speed up the length change process and also provide a superior cut edge appearance. These devices have proven themselves perfectly if you need to quickly slit a panel longitudinally.

In no case should we forget that when working at increased rotational speeds of the cutting tool on the surface that is being processed, defects in the form of melted edges may appear. In this case, unpleasant odors and substances harmful to health are emitted into the work area. It is necessary to decide which circle to process. In view of this fact, at first all work must be done at reduced speeds. With an angle grinder, you can get not only straight cuts, but also curly cuts.

Experts recommend using a regular jigsaw to obtain a high-quality surface, as well as increased productivity, as a tool used when cutting. In this case, an excellent smooth edge is obtained, which does not have any creases, and is also very practical in the process. The tool has proven itself perfectly both for longitudinal cutting and when cutting across the bar.

When using a jigsaw, you need to remember that you need to use a file with a fine tooth. Particular attention should be paid to the cutting mode. the minimum speed is selected and the pendulum stroke is turned off. This tool is excellent for cutting multiple panels at the same time.

This tool is perfect for cutting small quantities of plastic panels. Applying it, you just need to know some little things that can help and facilitate the process of changing the length.

The least suitable for such work is an ordinary kitchen knife, which can be found in any kitchen. Difficulties in working with this cutting tool arise due to the width of its blade. Even when perfectly sharpened, a kitchen knife will not cut through wall panels.

The performer will have to spend a lot of time if he does not have the opportunity to use another tool. In this case, the installation process will take longer.

A stationery knife is considered a more suitable tool for this, because using it, the material is not completely cut. After drawing along the front surface of the material, a groove is obtained. Turning over the bar and pressing on the edges, the PVC panel clearly breaks off along it, and the resulting small fringe, which covers the surface of the fracture, will absolutely not harm the appearance of the room in any way, because in any case it will be hidden either under the curbs or under the skirting board.

a loaf knife made of ceramics can also carry out such work. It will do a great job with plastic panels due to the presence of a wavy cutting edge. Working with such a tool, it will not be difficult to get an element that will perfectly fit into the interior of the bathroom.

To cut PVC panels, you can use different tools, each of which has its own advantages and disadvantages. There are also specialized professional tools to speed up and facilitate cutting.

How to cut a PVC panel with a utility knife, see below.

How to cut PVC panels?

PVC panel is one of the most popular materials for interior decoration. Its use in the interior attracts not only by its appearance, but also by its affordable price, ease of maintenance and installation. Due to the listed characteristics, many people prefer PVC panels, rather than tiles, when decorating personal hygiene rooms.

Power tool

For quick sawing of PVC panels, a power tool at hand is best. For this purpose, you can use almost any device, which will help to significantly reduce the time spent on preparing for installation.

Often, cutting is performed using the following devices:

  • jigsaw;
  • angle grinder;
  • circulars.

To work with plastic material, it is allowed to use only low revolutions, because with significant heating it begins to melt and release fumes that are toxic to the human body, and the cut in this case will turn out to be torn.

Using a jigsaw will help make the process of preparing PVC panels for installation much faster than using a hand tool.

However, with such a method of processing, the following nuances must be taken into account:

  • before starting work, it is necessary to turn off the pendulum stroke;
  • a file with as small teeth as possible should be used;
  • you need to set the lowest speed of movement of the file, which will avoid excessive heating of the plastic at the cut.

Using a jigsaw is very convenient to cut stacks of panels, but make sure that their height does not exceed the length of the file installed in the tool.

The angle grinder is recognized as the most convenient and practical power tool for cutting PVC wall panels. By installing a cutting disc, you can make not only straight, but also curly cuts on the surface of the plastic. When processing plastic with a circle of an angle grinder, it turns on only at low speeds, which will avoid damage to the material due to melting of the edges.

In the absence of more practical and convenient tools, PVC can be cut with a knife.

To solve this problem, the following types of cutting products are suitable:

  • Kitchen knife. This tool is suitable for cutting multiple panels in the process of repairing or replacing them. For large-scale wall decoration, such a procedure is unnecessarily long and painful.
  • Construction knife. Among hand-held cutting tools, such a device is one of the best options for achieving a straight cut with relatively little effort.
  • Stationery knife. Using a wooden ruler or square, this tool allows you to achieve a perfectly even cut of the panel, therefore it is often used to cut them.

Choosing a cutting tool

Specialists in the implementation of repair work, who have to carry out the installation of PVC panels in their professional activities, know many secrets regarding the correct cutting of plastic materials up and down. After analyzing them, each owner who wants to make repairs on his own will be able to choose the most suitable professional tool for him or use the tools at hand.

The choice of a method for cutting panels usually depends on the tasks and capabilities of the master. Below are the types of cutting materials.

Hacksaw

One of the universal devices for cutting any material is a hacksaw, which is sure to be found in the arsenal of any craftsman. It is she who will help, if necessary, cut the plastic wall panel. Such work will take more time than using a special cutter, but with significant volumes of cladding, this will not significantly affect the overall duration of the repair.

When using a hacksaw, you should listen to the following recommendations of experts:

  • for working with plastic finishing materials, you should use a tool with small teeth, which is usually designed for working with metal or wood;
  • to shorten the PVC panel, there is no need to apply strong physical forces, which can lead to damage to the material;
  • you can cut several parts at once with a hacksaw by folding them in a pile and securing them to avoid bending or displacement.

To prevent the incision from being serrated, it is not recommended to use a tool with teeth set apart in different directions.

Basic cutting rules

So that the efforts on cutting PVC panels are not wasted, and the result of the work meets expectations, experts recommend adhering to a number of rules for working with plastic. These little secrets will help not only to significantly reduce the amount of spoiled material, but also save the master from unnecessary financial expenses and injuries.

When carrying out work in the heated season, do not start cutting panels that have recently been brought into the room. The plastic should naturally warm up to room temperature, which is achieved in at least 12 hours. The fact is that at low temperatures the plastic panel becomes fragile, and therefore it can crack and break off in large fragments.

Regardless of the chosen method of processing the material, it should be placed with its front side facing you, which will avoid deformation of the panel and difficulties during its further installation. When cut from the seamy side, you can find microcracks on the front part, which will manifest itself over time and significantly spoil the interior.

It is necessary to mark in advance the straight line of the planned cut, which can be done with a simple pencil and a stationery ruler.

How To Cut PVC Walling

To speed up the process of preparing the material for installation work, you can cut or saw several PVC panels at the same time. To do this, it is enough to fold them in a pile and create a two-point support. It is best to rest the opposite edge of the stack against the wall, which will help avoid shifting the products, respectively, as a result, parts of the same length will be obtained.

Cutter

If necessary, this tool can be independently made from available tools, for which it is enough to adhere to the following recommendations:

  • it is necessary to prepare a metal strip, the thickness of which is at least 2 mm, and the width is 1 cm;
  • then one of the edges of the workpiece should be cut off at an angle of 45 degrees;
  • it is necessary to sharpen the edge of a homemade product using a grindstone;
  • the opposite side should be wrapped with electrical tape, which will allow you to protect your hand from damage during work.

A professional cutter for plastic has a relatively low cost, so its purchase can be a profitable investment, because thanks to such a tool, the process of cutting PVC panels becomes not only more convenient, but also quite fast.

Material features

PVC panels are one of the modern types of finishing materials that are made by extrusion and are used both in the bathroom and in the living room. The main raw material in the production of such products is polyvinyl chloride, which is used to fill the mold. To give the panels the desired color, a certain amount of crushed natural chalk is added to their composition.

Decorating PVC panels can be done in one of the following ways:

  • staining;
  • thermal printing;
  • offset printing.

Thermal printing is applied to the plastic surface using a special roller heated to high temperatures, which presses the film to the surface of the product. Thanks to this technology, it is possible to quickly and clearly apply a pattern without losing the brightness of the image. The panel itself does not need additional varnishing. Offset printing is used much less frequently due to its high cost.

How to cut plastic PVC panels

Plastic panels have a number of advantages that make them an indispensable material for quick and inexpensive renovation of bathrooms, toilets, loggias and garden houses. The panels are impervious to moisture, are low-combustible materials, resistant to mechanical abrasion, have a long service life and are relatively cheap. They can be used to decorate both walls and ceilings. The technology of mounting plastic panels is simple and does not require preliminary surface preparation.

One of the essential stages in the installation of plastic panels is their cutting to the required size. The complexity of this stage depends on the state of the surface to be finished: if the wall, for example, is straight and even, then you can prepare the entire volume of plastic panels required for it in advance. If the wall has different heights, complex shapes, or includes architectural elements (windows, doors, ledges, etc.), then you will have to cut the panels along the way, which, of course, significantly increases the installation time.

How to cut plastic PVC panels?

It should be noted that plastic panels are quite easy to process, and they can be cut using a wide variety of tools. Most often, hacksaws for metal or wood with small teeth are used for this. The advantage of this method is that they can simultaneously cut several panels. It is necessary to saw the panel face up, at a slope, avoiding strong pressure. If you use a saw for wood, it is better if it has teeth for cross or mixed sawing, if possible, not set apart. such a saw will leave an even cut without scoring. You can also use a jigsaw, but when cutting, they need to strictly dose the pressure, otherwise the panels can simply break. Some people use “angle grinders” and circular saws to cut panels to speed up the process, however, in our opinion, such methods have several drawbacks: firstly, plastic is quite fragile and light material, and careless handling of it can lead to the fact that the panel will simply break; secondly, from heating when cutting with a tool at a high speed of rotation, the panels heat up and begin to release toxic compounds.

There are a few rules to follow when cutting panels. If you brought the panels from the cold, let them “warm up” at room temperature for several hours: cold plastic becomes brittle. Before cutting the plastic panels, mark them to the size you need. It is convenient to do this using an ordinary felt-tip pen. it leaves a clearly visible mark on the panel and is easily erased. Safety precautions must be observed when cutting panels. It is advisable to wear protective goggles and gloves. Remember that when the panels are broken, sharp splinters are formed, which can injure yourself.