The better to cut the laminate. Laminate saw

How to cut a laminate: select a tool

Laminate is a relatively new floor covering, but gained well.Deserved popularity due to practicality and aesthetic appearance. In addition, it is easy to assemble it yourself, having completed all the necessary measurements.

Laminate boards during assembly must be laid in a checkerboard pattern in order to give the strength of the entire structure. Therefore, each row requires correction in length, both at the beginning and at the end.

It’s not so difficult to shorten the boards or cut pieces of a certain shape, the main thing is to make the right choice. Than to cut a laminate at home. Consider which tools can be used to cut a laminate board.

We take a hacksaw in your hands

The laminate of the hacksaw, of course, will cut, but it is not very suitable for such work. After all, the teeth of a hacksaw designed for wood work are frighteningly large, and the upper floor of the flooring is so thin. Togo and look. Ugly traces will remain from these teeth. And cutting the pressed structure of the laminate is hard. Hands get tired.

To get a good result, we arm a hacksaw with small teeth. For example, a hacksaw designed for cutting metal may well fit. CHARS on the cut will be avoided, but it will be more difficult to cut fine.Toothed with a hacksaw than a tool for wood. However, if you do not intend to saw the laminate in large quantities, then this method is suitable. The quality of the cut, of course, is not perfect, but quite tolerable.

And here are the promised little tricks: before sawing, stick a piece of painting tape to this place. If you do this, then chips are not formed at the site of the cut. Over, the laminate board must be placed upward. And to make the cut smooth and clean, the hacksaw must have small frequent teeth.

Since the laminate is pressed using special mechanisms, it is natural, it is better to cut it not manually, but an electric tool.

For example, for this, an electric burner is quite suitable, (saber’s saw) which is increasingly used by home masters.

Using a hacksaw for a cut of laminate

Cutting for metal is what to cut the laminate will be profitable, because the tool of those that are in almost every house and you will not have to run to the store.

It is very convenient to perform small cuts with a hacksaw for metal due to the fact that:

  • The laminate is easily lend itself to manual cutting;
  • A small hacksaw tooth guarantees the absence of chips;
  • If you still damage the edge, then you can easily close the shortcomings with a baseboard.

Remember that a hacksaw for a laminate is suitable only if the volume of work is small and there is no other tool at hand, also if you do not have a hacksaw at hand, it is better to buy a jigsaw in the store, which will be mentioned below.

The sawing should be carried out according to the following instructions:

  • First make a clear markup on the lamellas, remembering that it should be bright, because when sawing it will be covered with a thin layer of dust.
  • To get a high.Quality edge, cut the sheet, turning it with the front side up.
  • Do not make much effort to the tool so as not to damage the finished edge.

The hacksaw clearly does not lead in the ranking than to saw the laminate, but sometimes a person has only it at hand. The classic hacksaw has very large teeth, and with their help it will not be possible to cut the board quite beautifully.

Explicit drawbacks include the duration of the process. The use of a hacksaw can be justified if it is necessary to file a small angle or make a cut across the board. The use of a hacksaw for a cut of a laminated board along the entire length is a catastrophic loss of time.

Than and how to cut a laid laminate

There are situations in which it is necessary to cut the laid laminate. You can do this by fulfilling two conditions:

  • Gently and as accurately as possible make a mark with a square;
  • The tool is installed at minimum speed, so as not to accidentally cut off the excess.

3 Best Tools for Cutting Laminate Vinyl Floor| Laminate cutter Jigsaw Small Saw MrYoucandoityourself

Pruning is performed using a renovator, jigsaw or grinder. They do not press the tool, but only directed by marking.

How to cut the laminate against the wall without analyzing

You can cut or align the ends along the wall with a grinder or jigsaw. The gap of 15-20 mm makes the process complicate. Therefore, before cutting the laminate on the floor, it is necessary to weight the panels with sports dumbbells or sandbags. The tool is tuned at low speed and neatly led along the wall.

Sprinkled the laminate with a hacksaw

Scabble. A tool that can be safely used by those who do not plan to saw laminated boards in large quantities, owners of small rooms. With the help of a hacksaw, it is difficult to ensure the ideal quality of the cut, but it will still be at a quite decent level.

A product with large teeth falls under the ban, working with this tool will inevitably lead to the formation of ugly traces. To obtain the optimal result, experts recommend giving preference to a hacksaw with small teeth. For example, you can choose a hacksaw for cutting metal. With such a tool it will be possible to prevent formation on a cut of chips, but it will still be more difficult to work than using a special tool for wooden products.

How to saw correctly. Before the cut of the laminated board, a piece of painting tape must be glued to the site of the saw. Such an action will prevent the formation on the section of the chips. Be sure to put a laminated panel so that the front coating is at the top, it is much more convenient.

Special cutter, guillotine for laminate

The home master definitely should not purchase this expensive tool. Over, he can cut a laminate along it very badly. For 40-50, which are asked for it, it is better to buy a more expensive electrician. The device consists of the base and a handle with a blade for cutting lamellas.

See also  Miter Saw For Wood Which Is Better

The principle of its work is quite simple. Put the plank of the laminate on the base and lower the handle down. However, when working with this tool, there are features. Here they are:

  • As already mentioned above, this guillotine does not cut well along;
  • Cuts off very not carefully, the cut piece looks like a stub. Even the sharp blade of the Rezak literally tears laminate;
  • You need to make a lot of effort, and the blade is quickly stupid. Hands are very tired. A thick laminate of more than 8 mm may not cut;
  • Used only to cut the laminate. T.E. In the farm, this device will no longer come in handy. So, for home conditions is not suitable.

#2. Laminate cutter

A manual cut for a laminate is a specialized tool made in the form of a supporting structure with a fixed cutting blade. The principle of operation can be compared with guillotine. The thickness of the cut material and the length of the cut itself varies depending on the model.

The average laminate thickness rarely exceeds 0.8-1 cm. Therefore, it makes no sense to buy professional cutters. Equally equipment of the average price category cost is 1,500-1700 rubles.

A cut for a laminated board allows you to get a quick result with minimal costs

better, laminate

Can be cut both along and across the canvas. The only thing that the quality of cutting along the canvas is highly dependent on the length of the cutting element. But for laying the last row, the quality of the edge does not play the role much, since the cut part will be covered with a skirting board.

The process of working with the cutter looks as follows:

  • Apply marking on the front side of the laminate;
  • Remove the handle with the blade back and lay the panel on the supporting structure;
  • We set the panel so that the cut line of the part we needed was a little to the right of the knife (to the left for left.Handed people);
  • Smoothly lower the handle until contact with the panel, press and saw before cutting off an unnecessary piece.

After the cut, the front side remains even and intact, and pieces of papers and torn edges can remain on the back, which should be sanded with sandpaper.

Expensive and professional cutters on both sides are more even, since the handle has a great weight, and the sharpening of the blade itself is better.

How to cut a laminate at home?

You can choose one of the most popular and affordable options. Before you pay for the device, learn more about its capabilities and nature of the work:

  • Hacksaw. This is not to say that this is a modern option, but in some cases it turns out to be very helpful. The hacksaw never fails. For the best result of work, it is better to use a hacksaw for metal or wood with a small tooth. Start the cut on the back of the panel to prevent possible chips on the surface of the board;
  • Bulgarian. This is an angle grinding machine with a metal disk. How to cut a laminate correctly? Fix the lamella and slowly lower the grinder so that it does not break out of the hands and does not stalify. Get ready for the fact that during operation an unpleasant smell will appear due to heating the disk;
  • Cutter. Here is another popular device for cutting laminated material. It allows you to cut boards quickly and efficiently. The cutter is without effort to cope with both thin and thick panels. Such a perfect result cannot be achieved either when using a grinder or using an electrician. This is a device with a sharp blade, which is easily set in motion with a handle. Such a mechanism works very quietly, without noise and dust and does not need power supply;
  • A circular saw. What kind of file to saw laminate? This is an option for a neat saw, equipped with a special disk. Put the board on the hard even surface with the front side, securely fix it and apply a cutting line. Then smoothly lower the disk of the grinder and gradually move it along the intended line without stuck in the board. It is this option that requires skills in working with a circular saw, as well as great patience. But, the advantage in a qualitative and fast result. Are there any cons? Yes, if the smell of a burning tree can be considered a minus that appears in the process of sawing;
  • Electric jigsaw. This is quite effective, but a simple option. Make sure the jigsaw equipped with a special wood nozzle. Before starting work, you need to fix the lamella on the floor. Turn on the device and set it up for increased speeds to protect the material from possible chips. Your movements should be smooth.

! At least two people should work with an electrician.

Conclusion

Each master can always choose equipment for cutting a laminate in accordance with individual wishes and capabilities. However, any device must meet the basic operating requirements to achieve the desired result, be comfortable to use and not have a clear marriage, which can lead to sad consequences due to impaired safety precautions.

Rice. 12. All laminate cutting tools

If professionals use expensive tools for their multiple use on different objects, then for a beginner cheaper analogues with similar characteristics, but less life resource.

How to cut a laminate

The choice of flooring largely determines the quality and price. In this regard, the most acceptable ratio has a laminate. The material owes its popularity not only practicality, but also the simplicity of laying. In the presence of the tool, the installation of the flooring is capable of performing each. Accordingly the question arises. How to cut a laminate?

To lay the flooring, the material must be taken 10-15% more than the area of ​​the room. The panels will need to be not only connected, but also to cut. To adjust the dimensions, use a manual or electric tool. When used at home, it should:

The last characteristic when choosing a method for many repair lovers is a key. But its importance is somewhat exaggerated. The presence of chips up to 5 millimeters will hide the baseboard.

Both experts and home.Made master for cutting laminate use:

Features of laminate cutting

The panels consist of three layers: polyurethane film, paper and pressed wood fibers. Each tier differs in structure. When cutting, the film breaks off, the paper leaves the fringe, and the wood plate forms dust, clogging the locks. Before cutting a laminate at home, people’s craftsmen study videos or photos of instructions for working with various tools when cutting panels.

See also  How to sharpen a band saw correctly

Manufacturers produce 6-12 mm thick plates. Depending on the size, tools are used. Thin products are cut with a construction knife or cutter. The blades are used sharp so as not to roll the decorative layer of material. Laminate is placed on a board with a thickness of 8-10 mm and cut.

It is difficult to cut flooring with a thickness of above 8 mm with a knife with a knife, so experts advise using the power tool. For trimming, they use:

Kryazuvka for metal

Cutting for metal is what to cut the laminate will be profitable, because the tool of those that are in almost every house and you will not have to run to the store.

It is very convenient to perform small cuts with a hacksaw for metal due to the fact that:

  • The laminate is easily lend itself to manual cutting;
  • A small hacksaw tooth guarantees the absence of chips;
  • If you still damage the edge, then you can easily close the shortcomings with a baseboard.
better, laminate

The sawing should be carried out according to the following instructions:

  • First make a clear markup on the lamellas, remembering that it should be bright, because when sawing it will be covered with a thin layer of dust.
  • To get a high.Quality edge, cut the sheet, turning it with the front side up.
  • Do not make much effort to the tool so as not to damage the finished edge.

The cutter, how to cut off, knife, hacksaw, than cut, saw, than sawing without chips, it is better to saw off, tool in the photo and video

Laminate. Flooring, which is increasingly found in every house. Its installation always requires fitting in length and width, because the lamellas should be laid, observing the rule of brickwork. Accordingly, the question appears from here: “How to cut a laminate at home?””. From this article you will learn about different tools and methods of fitting with their use.

About the choice of tools

The cutting of the laminate should be performed efficiently so that the cut line is straight and even, and the edge remains intact. All these items are easily easy to execute by choosing a suitable cutting tool for laminate. An example of the right choice is the fact that not every person can cope with a professional tool, so he should use the simpler tools with which he will perform this work more accurately.

The easiest tool that is available to all, but it is not the best solution. A laminate knife is suitable only if you want to make a small neckline under the ledge in the wall. If it is still possible to cut off the lamel, then it is almost impossible to do it along, because you will spend a lot of time and effort, and the incision will turn out to be poor.Quality and curve.

If you decide to use the knife, then check its sharpness, because you will make much more flaws in the work with a stupid foot than sharp.

Kryazuvka for metal

Cutting for metal is what to cut the laminate will be profitable, because the tool of those that are in almost every house and you will not have to run to the store.

It is very convenient to perform small cuts with a hacksaw for metal due to the fact that:

  • The laminate is easily lend itself to manual cutting;
  • A small hacksaw tooth guarantees the absence of chips;
  • If you still damage the edge, then you can easily close the shortcomings with a baseboard.
better, laminate

Remember that a hacksaw for a laminate is suitable only if the volume of work is small and there is no other tool at hand, also if you do not have a hacksaw at hand, it is better to buy a jigsaw in the store, which will be mentioned below.

The sawing should be carried out according to the following instructions:

  • First make a clear markup on the lamellas, remembering that it should be bright, because when sawing it will be covered with a thin layer of dust.
  • To get a high.Quality edge, cut the sheet, turning it with the front side up.
  • Do not make much effort to the tool so as not to damage the finished edge.

Electric

This is a more expensive tool, but his choice is the best answer to the question of what is better to saw laminate. The jigsaw should be bought only if the volume of work is too large to cut everything manually or if you do not feel sorry for the money to purchase it.

How to quickly and easily cut laminate flooring without power tools

  • Install a canvas with a reverse small tooth in a jigsaw. If the canvas comes with an expensive and high.Quality tool, then you can use it, otherwise purchase it separately.
  • Draw a lamella.
  • In this case, the lamellas must be sawn, putting down the face down and fixed on a solid surface.

Another advantage of the jigsaw is that they can be sawn not only in a straight line.

A circular saw

The circular machine is not something to cut the laminate at any time, however, if you are a happy owner of such equipment, then feel free to start sawing:

  • Put on the shaft a disk with small teeth.
  • Draw a cut line on the lamella.
  • If the cut is carried out along the bar, then set the width on the machine.
  • Sprinkle the lamella, pushing in front of you.

The main advantage of the circular saw is the speed of its operation, which allows you to cut the lamel in a matter of seconds, however, due to the size that you can notice in the photo, it is rarely used, in addition, you cannot cut certain pieces of laminate, for example, on it, for example, under the column or ledge in the wall.

What a professional uses

In any business, an amateur is easy to distinguish from a professional, not only looking at the speed and quality of work, but also the tool used. This happens with laying laminate. Professionals use a laminate cutter, with which they produce a cut in a very short period of time.

As can be seen in the photo, this cutter is a hand machine equipped with a sharp blade, which is fixed on the basis. The blade is easily adjustable for different types of cuts. Using the machine, you can cut the lamella along, across and at different angles, without spending great efforts and electricity.

  • Lamel is put on the support of the machine in a horizontal position.
  • The cutter is adjusted for marking.
  • The builder puts the effort to the handle and the blade gradually cuts the lamella.

A professional machine is what to cut a laminate without chips becomes very simple, so everyone who is engaged in laying a laminate tries to purchase it.

You can use any of the presented tools, however, remember that the most important thing in sawing the laminate is the quality of the edge. Remember the advice: to make as few chips and irregularities as possible, do not make much effort to the sawing tool, because this will make the tool pull out the fragments from the body of the material, and not cut them out.

Now you know all the methods of sawing, so you can solve the question of what to saw off the laminate yourself.

See also  Circular and circular saw what is the difference

Kryzuvka for metal and saw on wood

One of the instruments of the home master. It is in almost every apartment or house, you can take it from the neighbors, in the event of emergency, buy it in the nearest household goods store.

Kryzuvka for metal allows you to get a clean cut without separation of decorative coating. And if it is decided to act with a saw for wood, it is advisable to choose a tool for garden farming, designed to cut branches and knots. The work with a hand tool looks like this:

  • With the help of a pencil or marker, a cut line is noted;
  • If you need a right angle of the segment, it is recommended to use a carpentry marking corner;
  • First, a decorative and protective coating is cut. This must be done carefully, minimally damaging the edges.

Then a board from MDF is cut out with a saw or hacksaw. These tools are the most common option when it is decided how to cut a laminate at home.

How to cut a laminate: we select a suitable cutting tool

In order to properly lay the laminate on the floor, you need to be able not only to connect laminate panels, but also to cut them correctly. Otherwise, “fit” into the area of ​​the room, as well as observe the traditional chess pattern will be impossible. Since you can’t take laminated boards with your bare hands, cutting them can be entrusted to one of the manual or electrical tools.

The main characteristics that should have a tool for cutting a laminate at home is:

The last point, the meaning of which is not to spoil the type of laminate board after cutting, for most home masters is a decisive. However, its meaning is still exaggerated. In any case, chips up to 5 mm in size on the finished coating will not be noticeable. Defects on the edge of the panels will be hidden behind skirting boards.

So, which tools are most suitable for cutting laminate?

Tool No. 1. Electric

The best result in the cutting of the laminate can be achieved by applying an electrician for this purpose. This is a light, very convenient tool to use, to which any master-novice will quickly find an approach. Even a woman or a teenager. The cut with an electrician is performed at increased speeds, which avoids damage to the structure of the fiberboard. If you act quickly, confidently, then the cut will turn out to be almost perfect.

The main thing in the use of an electrolobian is the choice of files. A modern tool is usually originally supplied with special files for cutting laminate. They are distinguished by a special shape, step and method of wiring teeth. However, ordinary metal files for metal will also cope with this business. Narrow, with small teeth.

In order not to damage the decorative surface, the cutting line is applied (pencil or chalk) on the wrong side of the laminate board. It is laid on the table (chair) by the wrong side up so that the part that is planned to be cut is in limbo. With one hand they fix the laminate lying on the table, and the other quickly cut off the excess part.

Tool No. 2. A circular saw

A neat cut along the edge of the laminate can be obtained using a circular saw with a metal disk. Working with a circular saw is more difficult than with an electrician, so it requires some skills. If you have them, then you can cut the laminate quickly, exactly, almost without chips.

The laminate board is laid on the hard surface with a pattern up, fixed. You need to cut carefully, with a little pressure, moving the disk along the drawn line, trying not to slow down in one place.

Tool No. 3. Angle.Grinding machine (Bulgarian)

Bulgarian. A convenient tool that is indispensable in the box of a home master. You can cut almost everything, including laminate. For a beautiful edge, without cracks and chips, when cutting, you need to turn the laminate board with the front surface. At the same time, metal disks, concrete or ceramic tiles are used.

Disadvantage of using a grinder (and circular saw too!) can be called a large amount of dust that will be released during laminate cutting. Also, this action may be accompanied by the smell of a burning tree. Therefore, you need to do a harsh on an open balcony or on the street.

Tool No. 4. Hacksaw

Laminate can be successfully cut with a conventional hacksaw on wood. But this will have to spend strength, because its teeth are quite large and will bite into the laminate, and not to cut it. Smaller teeth in a hacksaw for metal. It must be used for sawing.

How To Undercut a Door Casing Trim: High Quality Full Video

Scabbard is very often used for cutting with small volumes of work. In construction teams, this method is not applied, due to increased time costs and complexity.

Laminate flooring: custom cuts

Tool No. 5. Laminate cutter

Laminate cutter, on the contrary, allows you to make cutting at a professional level. Most often, this tool works according to the type of guillotine. A knife, which, with the help of a handle, is lowered to the surface of the laminate and cut it. The cutter acts easily, without chips and noise. For its use, you do not need to use force and have skills. Perhaps this is the easiest tool in operation, which allows in any conditions to get an excellent result.

Since this cutter is used exclusively for the laminate, it makes sense to buy it only with professional styling. For the decoration of several rooms of the apartment, this option is considered impractical.

Tool No. 6. Construction knife

An ordinary building knife can also be used for laminate cutting. For example, if you have almost finished the flooring device, it remains to cut one board, but suddenly a grinder broke. There are no other tools at hand, and the cut should be done urgently. Then a construction knife will come to the rescue. Put the ruler on the front side of the laminate board, draw a deep cut on it with a knife. Holding the board on one side of the cut, press on the second side. The laminate should be broken, just like ceramic tiles under the influence of tile cutter.

Features of cutting vinyl laminate

High resistance to erasing the upper layer, similar to commercial panels, makes vinyl coating in demand. In addition, such material creates an original decorative effect. The structure of vinyl panels is different from ordinary, softness and viscosity.

To cut such a material, it will be best to use a construction or stationery knife. This tool will cut all layers of vinyl laminate, subject to mechanical destruction.

After studying all the methods of cutting and the possible use of a particular tool, each selects the required device, depending on the task and the availability of.