The lawn mower is choking at high speeds. The lawn mower stalls when pressed…

The lawn mower stalls when opening an air damper

Where to start the diagnosis of defects if a trimmer is not started for grass? In situations where the tool stalls immediately after launch, it is worth looking at the subsequent units of the unit:

Specifically, the breakdown of the above locations often often leads to the fact that a trimmer for grass is poorly started. Let’s see how to remove such problems.

If it stalled at high speeds

If the carburetor stalls at huge speeds, this means that in idle and small there are enough incoming fuel, and to work on large ones is no longer enough. Then you need to check the serviceability of the subsequent nodes of the trimmer for the grass.

• Fuel hose. its integrity could be violated as a result of cracking. In this case, the substitution of the part is needed. Or maybe you just need to pull the clamps.
• A filter network between a carburetor and a hose for supplying a gasoline consistency-it could clog. In this situation, you need to clean the part.
• The valve on the gas tank cover. he could stick or clog with garbage. You also need cleaning.
• Carburetor. maybe as a result of unchanging vibration, its reservation occurred. This is usually typical for cheap Chinese details. To eliminate the task, you need to set up according to the annotation. In some cases, it is enough to loosen the tightening of the carburetor case. If the adjustment is not possible, you need to install a new element.
• Additionally, check the air filter. Maybe it will need to be washed and cleaned or changed to a new one, because he could clog with dirt and particles of grass when tilted technology, when the user mowed in inaccessible places.

Ways to eliminate breakdowns

The following works are possible by carburetor:

• cleaning and adjustment of the fuel supply valve;
• similar work with a valve producing spent gases and pairs (after fuel burning);
• replacement of the spring weaker on the entrance valve;
• restoration of the tension of the carburetor cable;
• replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
• changing the rotor damper disk;.
• Change of faulty wire or ignition coil.

The list of work on the work may also include the cleaning of the nozzles (in a 4-stroke engine), replacement of the valve washer, gaskets in tanks and so on.

The lawn mower stalls

When buying a chainsaw, you should be prepared for the fact that, like all such tools, damage may occur that will require repairs.

But do not immediately run to the service center and pay a lot of money to the masters, convincing them of a serious defect in the device.

The lawn mower stalls at high speeds

Probably, the most common complaint about gasoline trimmers for grass is as follows: “The gasoline lawn mower jams”.

The reason for this, of course, may be a sufficiently serious malfunction. The engine of a two.stroke trimmer for grass does not develop turns and ceases to rotate. The FS 130 gasoline lawn mower gives gas and stops. However, in most cases, the situation is even simpler than it seems at first glance.

What to do with such a misfortune, first try to deal with its causes without the help of others, because, having found the reason, it’s even easier to cope with the trouble, and sometimes it is even self.destructive.

In fact, circumstances, that is, when gasoline burns at high speed, there are many.

Why is a Chinese lawn mower not developing momentum?

Trimmer for grass does not gain speed. a very common malfunction, which, of course, does not always have a regular solution.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

The first launch of new gas stations.Removing the grid from the silencer, began to work.

Another factor is the occurrence of failures in the energy system.

In this case, a braid for grass will stop at idle. At idle, the main secateur stops. GoodLuck 4300 chainsaw stops at idle video. The lawn mower stops when you press the accelerator pedal. The gasoline lawn mower is turned off at high speed. Problems with the power system can be caused by improper carburetor adjustment or incorrectly adjusted carburetor.

Excessive adjustment can be caused by vibration that occurs during the operation of a braid for grass.

However, an incorrectly adjusted chainsaw can be corrected by adjusting it in accordance with the recommendations of the user’s management.

In addition, sometimes gasoline trimmers for grass can be jammed due to the fact that the valve in the lid of the fuel tank just clogged or clogged.

To check this, try starting a trimmer for the grass by unscrewing the fuel tank cover.

If the device works fine in this mode, clean the valve.

Some tricks of work with a benzotrimer.

Now is summer, and gasoline engines have become a constant attribute on land plots. Great tool, powerful and mobile. You can mow grass with a gasoline trimmer and cut dry weeds. But sometimes the braid for grass does not start, works with interruptions or does not develop full power. Now, of course, is not the time to work! As they say, this is rather the vibration of the starter handle than the kosba.

Problems with the launch do not only have an old braid for grass, but also in the new. what is the answer? Only one thing remains. listen to expert advice and adopt their practical experience.

Ways to eliminate breakdowns

Subsequent work is likely on the carburetor:

• cleaning and adjustment of the fuel supply valve;
• similar work with a valve producing redesigned gases and pairs (after burning fuel);
• replacement of the spring more weak on the entrance valve;
• restoration of the tension of the carburetor cable;
• replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
• changing the rotor damper disk;.
• Change of faulty wire or ignition coil.

Immediately after the start

Smelting Motokos or a trimmer for the grass after starting is justified by subsequent reasons:

• impressive of previously adjusted valves;
• first the wrong settings of the valve mechanism;
• clogging with deposits of the fuel supply valve;
• the hose is worn or poorly annexed.

Due to the violated method of injection of a fuel, a lawn mower or a trimmer for grass is very vibrated in work.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

• The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
• The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
• Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

The lawn mower stalls

When purchasing a lawn mower, you need to be prepared for the fact that, as in all other similar tools, it may also have breakdowns that will require repairs.

However, do not immediately run to the service center and pay a lot of money to the masters who convince you of a serious malfunction in the device.

The lawn mower stalls at high speeds

Perhaps the most common complaint related to gasoline trimmers sounds like this: “The lawn mower stalls”.

Of course, the reason for this may be a rather serious malfunction. However, most often the situation is much simpler than it seems at first glance.

To cope with such a problem, first of all, try to deal with its causes on your own, because, having found out the reason, it is much easier to fight the problem, and sometimes it is even self.destructive.

In fact, the reasons are when the lawn mower stalls at high speeds, there are quite a lot of these reasons.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

over, the lawn mower can stall due to poor fuel flow into the carburetor

Why then the device starts up, ask you?

The reason for this is that at first the fuel gradually falls into the carburetor and is enough for work with increased power.

However, then it is produced and at large speeds the engine begins to stall.

As for the carburetor, here the problem may also be that its body is too pulled.

The reason that the lawn mower stalls at high gas speeds may also be an air leak.

We are talking about the possible presence of a place through which air can pass during the heating process of the engine.

Among other things, do not forget to check the fuel intake hose. The problem may be that it is weak or cracked at all.

These are the main reasons why the gas mowl can stall.

The lawn mower stalls

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when lawn mower stalls at high speeds, there are a lot of these circumstances.

Trimmer for grass does not gain momentum, what to do?

1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

over, the lawn mower can stall due to poor fuel flow into the carburetor

Why then the device starts up, ask you?

The reason for this is that at first the fuel gradually falls into the carburetor and is enough for work with increased power.

However, then it is produced and at large speeds the engine begins to stall.

As for the carburetor, here the problem may also be that its body is too pulled.

The reason that the lawn mower stalls at high gas speeds may also be an air leak.

We are talking about the possible presence of a place through which air can pass during the heating process of the engine.

Among other things, do not forget to check the fuel intake hose. The problem may be that it is weak or cracked at all.

These are the main reasons why the gas mowl can stall.

In recent years, a gasoline trimmer for the grass has made the status of one book from the main tools in the arsenal of summer residents. And such an environment is logical, because a motorized braid for grass allows you to quickly put a personal plot in order. But with the form.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Operating advice

It is worth paying attention to several recommendations for working with a benzoca or a trimmer, extending the service life of the device to several times.

• As soon as you notice that the lawn mower or trimmer vibrates for the grass. immediately stop working and check the serviceability, performance of specific parts.
• Valves adjustment and checking the work of pistons and cylinders, cleaning and changing the nozzles perform, starting from the requirements set forth in the user guide and the recommendations of the masters of service centers.
• When air bubbles enter the system due to impaired fuel hose-give in to gas. With the combustion of gasoline with higher speeds of the gas bubbles motor will be less. But this is a temporary measure. As soon as possible, disassemble the unit and eliminate the cause of the suction of excess air.
• Do not work as a unit in cold weather, not heating the engine. under load it can often stall. The effect here is the same as in the case when the driver in.40 started the car and immediately drove off, without waiting for the engine heating.
• Do not leave the unit on the roadway. During the accident, the hit will immediately break, and this will make the purchase of a new unit for a forced measure. A car that has crashed into it at best will receive damage to the body and bumper.
• Avoid working with a motorcycle or a trimmer in a downpour. Water getting along with air in the worst case can lead to engine explosion. Similar situations arose with cars.
• Do not use unverified vehicles and lubricants. The mower warms up the engine more than it would do the car itself. when overheating, it will automatically lose its lubricants. It will turn into a burned out reagent. sticky, too viscous and viscous, like fuel oil. He will immediately stall (and drown out) the motor.
• If the oil is old, previously merged from the tank of the machine or other (or the same) lawn mower (on a 4-stroke engine)-defend it, filter to clean from dirt and metal. But at the first opportunity, purchase fresh motor oil.
• If the engine is two.stroke. observe the ratio of gasoline and oil. For compositions with mineral oils, this is approximately 34: 1, for semi.synthetics. 42: 1, for purely synthetic. 50: 1. Do not violate these proportions: “rewinded” gasoline will not burn out and quickly clog the engine, “under.appropriate”. will accelerate the wear of its mobile parts.
• In terms of viscosity to winter classes, they include marking oils: SAE-0W/5W/10W/15W/20W/25W. To the summer-SAE-20/30/40/50/60. For example, SAE 10W-40 is already all-season oil (when working mowers from spring to autumn inclusive). Be sure to check with the manufacturer exactly what oil is needed.
• Always use high.quality gasoline that has passed the manufacturer all stages of cleaning.
• Recommended octane number of gasoline-AI-92/95/98. The use of the 76th can lead to a non-power of the engine by frequent stalling if you are poured, for example, the 76th or 80th gasoline.
• If you are not sure of the independent solution of problems with a gas station (which does not gain move and often stalls)- call the master or contact the service center for repairing motor and garden equipment. Specialists do not get used to doing this work for you.

Read how to use a trimmer for grass video

Observing all these precautions, you will give your mower for many years of fruitful work, and yourself. the luxury of well.groomed lawns, comfort and convenience when mowing unnecessary vegetation in your site.

About the reasons why the lawn mower stall when you press gas, watch in the next video.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

• Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
• A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
• The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
• Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
• Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

• First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
• Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
• Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
• Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.
• If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
• After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Low quality fuel use

The benzotrimer does not gain speed in case of poor.quality fuel. He may stop or not start at all. To check the quality of the fuel, you need to inspect the candles. They are the main indicators for solving problems with the combustion chamber.

In the presence of sediment, a raid, plaque, the old fuel merges, and another, high.quality.

or gasoline cutter should be filled with good quality gasoline and the fuel brands that the manufacturer indicated in the technical passport of the device.

For your information! Candles should be thoroughly cleaned of plaque, and only after that they are again placed in the combustion chamber.

What to do if a benzotrimer is not gaining momentum

If you once purchased a trimmer for grass, working with gasoline, then you probably had to face the problem of turning on a trimmer for grass, as well as a problem as a benzotrimer does not gain momentum

That is why this article has been created.

So, what to do if a trimmer for grass, working for you for several years, suddenly just stops gaining momentum

, and the motor is simply stalling? In this case, you and I should consider a number of problems related to stopping the work of the motor.

The motor may stall under various circumstances. The lawn mower does not develop speed, the reason. | Funnycat.TV. Sometimes the reason for the incorrect operation of the trimmer for grass working from gasoline is the clogging of the air filter.

It is the filter that is one of the most important reasons why the operation of a gasoline trimmer for grass may stop

Various garbage very often gets into it, particles of dust that also clog the filter, so it needs to be cleaned and washed every month, and maybe more often, it all depends on what power the gasoline trimmer has for the grass, as well as then how often do you use this device.

Restoring the performance of electrical equipment

Mowers, inside of which electric motors are located, most often begin to be capricious due to oxidation of contacts. The terminals are covered with a layer of scale from excess humidity in the room or in another place of storage. It is also worth checking the absence of a break in wires in problem areas. For this operation, a multimeter or other tester type is used.

When a set of garden equipment contains a brush engine, we identify the performance. Brushes can wear out quickly, leading to a lack of contact. The reptity of them costs relatively little, and it is easy to find it in specialized stores, where they sell spare parts for such a technique.

Asynchronous engines are also in wait for the malfunctions. They refuse phase.drive capacitors. A similar situation is diagnosed at home is problematic. It can be detected by indirect symptoms:

• The sound of a buzz is heard;
• When starting, the case twitches slightly;
• significant heating of the motor occurs even at a slight load;
• Reduces are reduced.

It is worth diagnosing the condition on the tolerance/button and the voltage supply to the electric motor. Когда проведено тестирование описанных узлов, а нарушений в работоспособности не обнаружено, то вряд ли удастся исправить поломку газонокосилки своими руками. Then you will have to use the services of the corporate service.

At high speeds

The hole in the fuel cover (saepun) of a trimmer for grass

With a similar problem, it is worth paying attention to the fuel valve, which, when clogging, ceases to normally pass the fuel mixture. By solving this malfunction, it is weakening using a suitable tool. In addition, the problem with the circulation of the fuel mixture may cover in the contamination of the valve. To do this, just blow it with a stream of compressed air.

• etching of atmospheric air into the combustion chamber;
• problems with the circulation of a mixture of fuel;
• clogging the saapun in the lid of the fuel tank (cleaning the hole with a thin sewing needle);
• Incorrect carburetor adjustment.

When air sunses, when I operate ICE, it is necessary to check the tightness of the pipes and the integrity of the gaskets in the CPG. The problem with the circulation of the fuel mixture can be solved by the elimination of blockages in the fuel pipes leading to the carburetor. If a vacuum occurs in the tank and not receipt of the fuel mixture to the carburetor, it is enough to clean the soundtress with a thin needle and blow it with air.

If the lawn mower stops when pressing the gas, then the reasons may be the following.

• The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
• The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
• Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

When a braid for grass stalls at high speeds, this is due to the following problems:

• clogging or clutching a valve located on the gas tank lid;
• The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
• problems with the circulation of the fuel mixture;
• atmospheric air
• The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

Most often during the periods when the lawn mower stalls when the gas is added, the cause will be the air damper, more precisely, its condition: it clogged. Structurally, the part is located in the place where the resulting fuel is sprayed behind it, and, accordingly, the product collects all inclusions in low.quality gasoline.

• a clogged air damper;
• The clogged filter is fuel, and when you give gas, this is especially noticeable;
• the air of the crankshaft shaft occurs;
• damaged gasket between the cylinder and the carb.

When you cleared, washed and blowing the elements, but again the lawn mower stall when you press the gas-replace them with new ones, check the quality of the fuel, as well as the literacy of the proportions of the cooked mixture. When opening the air damper, the tool will stall for the following reasons:

• Dosage carburetor.
• The appearance of cracks on the fuel hose caused air leaks.
• The occurrence of problems with the oil seals.

In the process, there are situations when the lawn mower at high speeds is subject to a similar sharp stop. It occurs for the following reasons:

• due to problems with the circulation of the fuel mixture;
• with air leaks;
• The fuel intake hose is poorly connected or cracked and cannot be used;
• stab or clogged the valve of the cover of the gasoline tank;
• The carburetor was resolved.

In most cases, nevertheless, the cause will be a carburetor and related filter, hoses. If you need cutting gear or trimmer heads, then our site will also offer them to buy them with gasoline tools and components for them.

Why and what to do if a trimmer stalls for grass

There are several reasons why the trimmer for grass stalls when the grass. Usually the problem is provoked:

• wear of engine elements. piston, bearings, crankcase;
• malfunctions with fuel supply. a carburetor can fail in the device, sometimes a malfunction causes a clogged filter;
• mechanical damage to hoses, tubes and cables;
• disobedience with the ignition chain.

Most often, under a load for one reason or another, an old trimmer for grass, which has long been in operation, stalls for a particular reason. But sometimes the owners of new gasoline devices face problems.

Why is a trimmer for grass stalling when pressing gas, increasing speed

If the trimmer for the grass stalls when you give gas, then the problem is usually a malfunction of the carburetor adjustment. The malfunction often occurs if the device was inaction for a long time, and then received a significant load. Sometimes the unit stalls immediately after increasing speed, if before that it was operated in difficult conditions in violation of the rules.

The following reasons are also leading to problems with the performance of the device:

With stretching or rupture of the fuel hose in a gasoline trimmer, the elements that have become unusable must be changed. If the reason is in the clogged valves and filters in the unit, they are quite simple to clean.

If the reason that the trimmer stalls for the grass is caused by problems with the carburetor, the problems are accompanied by vibrations

Another common problem is that the trimmer for grass stalls with increasing speed due. In this case, you need to find the instructions for the device and carry out the reconfiguration of the unit. Often it is enough to weaken the tightening of the carburetor body.

Why does a trimmer for grass stall at idle

Garden trimmer for grass often stalls even at idle. The reasons for the malfunction are usually simple. First of all, the improper adjustment of the carburetor affects performance. it leads to problems both at high speeds and in idle mode. Turning off the device can provoke clogging of an air filter or throttle.

Sometimes a trimmer for grass stalls if incorrect fuel is used for it. The gearbox for this reason overheats and reduces momentum.

If a malfunction occurs, it is necessary, first of all, to inspect the carburetor unit and perform mechanical repair or configuration. If the cause is of poor.quality fuel, you need to replace the mixture with a more suitable.

What to do if the trimmer for the grass starts and immediately stalls

If the trimmer for the grass does not gain momentum and stalls immediately after starting, the problem usually consists in improper tuning the carburetor. In this case, fuel in the system comes unevenly, the gasoline unit vibrates and cannot work normally. Repair consists in reconfiguring a carburetor unit according to the instructions from the manufacturer.

Engine stop causes fuel supply valve. The element must be carefully cleaned, and then installed back in place. If the lawn mower still stalls immediately after starting, perhaps the valve is too tight and it needs to be loosened. In this case, the fuel mixture will begin to circulate through the system freely, and problems with the performance of the unit will disappear.

In some cases, a gasoline trimmer for grass stalls due to the fact that the hose contains damage that pass the air. During the repair, you need to replace the fuel tube with a new.

Attention! If the damage in the hose is insignificant, it is allowed to simply add a revolution drive. This will allow you to drive out air bubbles from the fuel system.

What to do if the trimmer works and stalls for the grass

Owners of garden gasoline units are faced with the fact that a trimmer for grass stalls at large speeds after a short work. First, the device begins to function with jerks, and then gradually stops.

Typically, the reason is the overheating of the system. gasoline in the carburetor simply boils. A trimmer for grass can heat up if the ignition circuit coil or wire is damaged. There is no point in repairing worn details, they are simply changed to new working.

The use of a trimmer for the grass does not lead the use of not disk, but rotary damper in a carburetor

What to do if the trimmer for the grass overheats and stalls

If a hot trimmer stalls for grass, the situation is a great danger to the performance of the unit. Repair should be carried out immediately, otherwise the device will be completely unusable, and it will be more difficult to restore it.

Overheating of the unit usually cause the following reasons:

• The use of inalitions. pour fuel into the tank with precisely with such an octane number that is recommended by the manufacturer;
• a large amount of air in the system. for this reason, the enriched mixture releases an excess of heat;
• non.compliance with the proportions of oil and gasoline in the preparation of fuel;
• The thick layer of soot on the muffler. soot is a good heat.insulating material, the gasoline braid for the grass during operation is very hot and stalls;
• The displacement of the axis of the spit.headed head inside the bar. for this reason, the rotation slows down, and the load on the engine increases.

If the gasoline unit stalls, you need to carefully examine it and eliminate first of all possible deformations of the structure. Then it is necessary to study the fuel parameters. If they do not correspond to the recommended, gasoline is replaced with a more suitable. If unnecessary air gets into the system, it is necessary to independently or with the involvement of specialists to adjust the position of the carburetor damper.

Sometimes a gasoline trimmer for the grass overheats and stalls because there is too old fuel in the tank. Use a fresh mixture for the unit, which was stored no longer than two weeks.

Attention! A trimmer for grass will overheat if you use it for too long, or mow with a weak device hard thick grass.

How to avoid breakdowns

Many breakdowns of a gasoline trimmer for grass can really be eliminated if you remove the causes, but if possible, it is recommended to, in principle, avoid faults. Simple measures allow to maintain the unit in a working state:

• You need to use a trimmer for grass in accordance with the recommendations of the manufacturer. It is impossible to use a weak device for removing hard weeds on the site, it is also not recommended to use motorcycles in excess of the due time. The gasoline unit needs to be turned off regularly and allow it to cool down.
• During the operation of the device, it is necessary to monitor the state of the cooling system. To maintain performance, the channels in the case are regularly cleaned, like the starter’s ribs. The clogging of the system often becomes the reason that the unit stalls from overheating.
• After using the gasoline trimmer for the grass, too, you need to clean. In this case, the procedure is not carried out for a hot unit, at first it must completely cool. For cleaning, use solvents, kerosene and other products allowed for use by the manufacturer.
• Before cleaning, the motorcycles for storage must be drained from the tank, the remains of unused fuel. If this is not done, the gasoline mixture will fall into heavy components and will clog the channels of the carburetor, which will subsequently cause malfunctions. After draining the fuel, the device is launched at idle and waited for it to turn off.

With the onset of autumn, a gasoline trimmer for grass must be correctly removed for storage. First, the residues of the fuel mixture are drained from the device, and then the unit is disassembled, rinse and clean all removable components.

Before harvesting gasoline motorcycles for storage, you need to evaluate the condition of its parts, carry out the necessary repair and replacement of nodes. Air filter needs to be cleaned. The engine is partially disassembled, rinsed and blown by moving elements, and then applied a new grease. To maintain the piston part, the candle is unscrewed and the piston itself is lifted to the top point, and a little oil is poured into the opening opening and the crankshaft is twisted several times.

Store a gasoline trimmer for grass in winter is necessary in a warm room