The trimmer coil for the grass is not unscrewed. How to disassemble and assemble a trimmer for grass

Repair of a trimmer coil for the grass with your own hands: how to remove, disassemble, change a fishing line for a trimmer, assemble and install back

In this article, we will describe in detail the procedure for how to remove the coil of the trimmer for the grass. Step.by.step instructions with the attached video will help a beginner and an experienced user to independently remove the element of the system and clean it or replace it with a new. Before you remove the trimmer coil for the grass, it must be drowned out. for gasoline samples or disables power. for electrimaters. We will demonstrate one traditional dismantling scheme, but in different models of trimmers, the method of attaching the coil to the tool may vary. With your own hands, you can not only remove the old sample of the coil, but also change it to a new one, if such a need arose. So, a step.by.step script:

Disconnect the tool from the network or turn off the engine (for benzos).
Carefully remove the cap of the coil, holding a spiral spring in place.
Click on clamps symmetrically located on both sides with one hand, and the second carefully remove the lid.
We are looking for a hole in the gearbox cup located on the side or from above, and combine it with the same hole in the shaft hub.
Using a playground key or a metal rod-we spread it into the gearbox hole, excluding the possible enlarge of the shaft.
Remove the mowing bobbin on which the fishing line for the trimmer is wound.
A slightly drowned screw will be visible in the depths. It can be unscrewed by a cruciferous or slotted screwdriver.
With one hand we hold the body of the head, and the second, counterclockwise, unscrew the screw.
Light swaying. remove the mowing head. Even if it acidified a little, we make delicately more efforts and with the same swaying. we remove it. Often movements are produced at the watch arrow, but coils are also found that are unscrewed in the other direction.
The assembly takes place in the opposite sequence.

Removing the bobbin has to be removed in cases of damage, winding of the fishing line (which is undesirable and indicates an illiterate selection of gear), and also when you need to wind a new cord with a new coil or replace the cutting tackle. Buy a coil for a trimmer for grass will always be inexpensively offered by the Kosikosa store.

The procedure for removing a mowing head of a trimmer for grass.

The design and fastening of the working part of the electric cocia differs significantly in different companies of manufacturers. But taking into account that in our markets there are many copies of acceptable recognizable brands, the order described can suit the owners and other portable garden equipment for the care of the lawn and grass.

Trammering head replacement tool.

For replacement, removing the head of the instrument, a nozzle in the form of a star will be useful to us, usually comes with the kit, or a flat wide screwdriver. Use a hexagon of a knife stars will not work, the nozzle slides, licking the edges of the sprocket on the screw.

Installation of a mowing head on a trimmer for grass Black and Decker.

Installation of a mowing head on a trimmer for grass is done in a flip sequence. When installing the screw in place, it is delayed by average effort.

I wish you a successful summer season and so that the garden technique does not fail. I hope my tips on how to remove the mowing head on the BlackDecker GL716 trimmer saved time and nerves for you.

Trimmer head with two antennae

After extracting the spray from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no principle distinction between bobbins with one and 2 grooves, but with a negligent refueling in a paired groove there is a place to be confused with the operation. Due to the likelihood of interweaving with a tool adjacent, a situation may appear when, after the wear of the workers’ antennae, it is unrealistic to extract new.

Regardless of the number of streams for refueling, a fishing line is taken for a trimmer from 1 length.5 to 3 meters. The winding needs to be created in a flip rotation of the head to the side, because the winding in the direction of movement will lead to the fact that the fishing line for the trimmer will not be removed from the bobbin. After the fishing line for the trimmer is tucked into the coil of the trimmer for the grass, free ends (15-30 cm) we stretch into special holes. Next, collect the head in the back of the order and check the performance. Do not worry if the ends of the 2nd antenpers are very different in size, since when the trimmer for the grass is launched, the knife installed on protection will cut off excess.

trimmer for stihl grass how to change a fishing line for a trimmer to a knife

How to replace a fishing line for a trimmer in any trimmer so, first we unscrew the nozzle. You need to do this, rotating the drum to the right. Here we have in our hands a drum with the remains of an old fishing line. We open it. Most often, the lid closes on the latches, which can be opened with a screwdriver by pulling it into the holes and slightly pressing it. Or you need to squeeze the lock and turn the lid towards the arrow. In this case, the cover itself must be held, t.to. There is a spring in the drums with automatically feeding the fishing line, which straighten up, can throw away all the internal parts of the drum. Gently taking out the coil, we remove the scraps of the fishing line from it.

Now you need to take 5 meters of a new fishing line and fold in half (to find the middle). In the middle part of the coil there is a recess (in some structures. a hole) for which you need to hook our fishing line for a trimmer. There is also an arrow on the coil showing the direction of winding. An important detail. if the coil has two compartments, then one half of the fishing line should be wrapped in one direction, and the second one in the other. Ending the winding, you need to leave 15-20 cm fishing line with free. There are also two recesses on the upper ring of the coil, through which these free ends need to be drawn. Directly with the winding itself, we coped.

The last stage of the process of replacing the fishing line is the assembly of the drum. First you need to install a spring and washers in your place. Then, holding the coil with one hand, the second you need to go through the ends of the fishing line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, pulling the fishing line for the trimmer and trying not to shift the spring. When all the internal elements of the nozzle will take their places you can close the drum with a lid. You just need to make some efforts so that the latches stand in their place. Voila! Kosyl nozzle is ready for work! When choosing a fishing line for your motor braid for grass (gasoline or electric), you should dwell on some points that we will talk about in detail about.

Fishing diameter. The engine power determines what maximum fishing diameter can be used for a given braid for grass. For example, the manufacturer of an electric trimmer for grass with a power of up to 1 kW recommends using a fishing line for a trimmer Ø2 mm, and with values of about 500 watts. only Ø1.5 mm. Also, the manufacturer of any powerful trimmer for grass with a curved rod recommends using a fishing line for a trimmer Ø2 mm. The gasoline engine is more hardy than the electric one. therefore, there you can install a thicker fishing line for a trimmer, which means a stronger one, which allows you to download more grass and work longer. You can select a fishing line for a trimmer for trawoks with a flat rod according to the next simple algorithm: the engine volume in dozens of cubic centimeters corresponds to the diameter in millimeters. For example, for the Husqvarna 128R travic, whose engine volume is about 25 cm3, a fishing line for a trimmer Ø2.5 ± 0.2 mm should be used. For more powerful black cutters with volumes of more than 40 cm3, only the geometric dimensions of the output of the mowing head are limited to the diameter of the fishing line. no more than 4 mm. So, a thin fishing line for a trimmer (about 1.5 mm) cuts out cultural lawn grass well, and a thick one (for example, 3.0.3.5 mm) successfully destroys weeds and even a young shrub.

Form of the fishing line. The simplest and cheapest in production is a fishing line for a trimmer of a round section. However, the requirements of ergonomics and environmental protection limit its use. due to its physical properties, it creates an unacceptably high level of noise (which is comparable to the noise of the engine itself). These are the classic round fishing line for the trimmer Husqvarna or Oregon Roundline or Chipmaster. To lower the noise level produced by the fishing line, they give it a special shape-they make it spiral as Oregon Duoline Plus (reducing the noise level by 15 dB) or with special transverse grooves as Husqvarna Whisper (-8 dB). Following the school laws of physics, the working part of the fishing line during the mowing process is only a end, not a lateral surface. However, to increase the severity of the fishing line, t.e. To increase efficiency, a cross.section from the round is changed to faceted: star.shaped, square or square with teeth. Oregon Starline, Nylsaw or Flexiblade. For example, according to experts, a fishing line for the Oregon Nylsaw trimmer, due to its square profile, is 27% more acute than its analogue of a round section, which clearly affects the increase in the speed of mowing.

#replace #any #diameter #form #trimmer for grass

How to wind a fishing line for a trimmer for a trimmer for grass correctly

Garden trimmer for grass is a useful tool that greatly facilitates the life of any gardener or owner of a private house. The grass is just rushing in the summer, especially after rains, so without it anywhere. But over time, sooner or later, the fishing line for the trimmer will end in it, and there will be a need to insert a replaced skein of a new fishing line. Some summer residents fall into a dead end. how to do it yourself correctly? So our article will help them.

Change a fishing line for a trimmer on a trimmer

This article will be able to tell you how to change the fishing line for a trimmer on a trimmer. For some people, this work may not be simple. But step.by.step instruction that is here will help you in this matter.

So, the first thing to do is remove the gearbox cover. Combine the hole on the side of the figure of the lower washer and axial seizure, insert the screwdriver to fix the shaft from the scroll. Now we unscrew the nozzle. The carvings on the shaft, as a rule, have a reverse cut, consider this when unscrewing.

Next, it follows the disassembly of the nozzle. There the lid is fixed with clamps through the holes. So you just need to second these latches in the holes, and the lid will be removed. If the nozzle has automatic \ semi.automatic modes of fishing line, then there is a spring inside, which when opening the lid can just fly out, be prepared for this. We lay out all the removed parts carefully in order.

Now it’s time to take a fishing line for a trimmer and unwind 5 meters from it, cut off this piece. Pay attention to its thickness, do not wrap a fishing line for a trimmer of greater thickness on the unit than indicated in the guide to the tool. Otherwise, an increased load on the engine and a higher fuel consumption during operation will be obtained. We bend the measured fishing line for a trimmer in half to find the middle and get a loop.

How to quickly refuel a fishing line for a trimmer trimmer for STIHL grass

First of all, in order not to resort to frequent replacements, it is better to use a denser fishing line for a trimmer. The number of its species and manufacturers is simply amazing. The main parameter of the fishing line for a trimmer for grass is its diameter. He varies from 1.6 to 3.2 mm. The most common view is a 2-mm fishing line for a trimmer. However, its selection must be carried out depending on your type of trimmer for grass.

Distinguish several variants of the cross.line section. So, it can be round, square, in the form of an asterisk with sharp faces. The last option is the most effective. However, it is worthwhile only on powerful braids and at the same time you need to know how to fill the fishing line for a trimmer into a coil of a trimmer for grass. Therefore, we can conclude that the more powerful your lawn mower is, the more the fishing line for the trimmer should be thicker.

A process such as winding a fishing line on a trimmer for grass is not difficult, but has its own characteristics. First you need to choose the right fishing line for a trimmer, the diameter of which is registered in the device passport.

First, unscrew the coil lid. Be careful, since the thread can be both left and right. The left thread is necessary so that during operation the head of the braid for the grass does not spin.

How to refuel a fishing line for a trimmer in a coil of a trimmer for grass and which is better to use for this?

Very often those people who have summer cottages, gardens in personal ownership, are faced with the need to care for the lawn on the site. In such cases, you just can not do without a regular hand braid for grass or a trimmer for grass. The first is slowly fading into the background, and the people who use it are getting less and less. The trimmer for the grass is automatically operated and does not require large expenses. over, the presence of a special skill is not necessary for its use.

How a trimmer for grass works?

The principle of operation of such a device is that the grass is mowing a special fishing line for a trimmer, installed on a fast.minded head. The number of revolutions per minute can reach 8000. For a short time, a fishing line for a trimmer is unusable, more precisely, erased. Then the summer residents have the question: how to fill the fishing line for a trimmer to the coil of a trimmer for grass?

Fishing line refueling in a trimmer for grass

Before filling the fishing line for the trimmer to the coil of the trimmer for the grass, measure 5 m from a skein (so many fishing line is installed on average on trimmers). Then fold it exactly in half in order to find the middle. The resulting center must be inserted into a special slot, which is located on the coil. After that, wind the fishing line in the direction of the arrow, which is on the head.

From what was written above it follows that the process of replacing the fishing line is not composed. Having carried out such a manipulation as winding the fishing line on the coil of a trimmer for grass, several times, you will bring this process to automatism. The only thing is to constantly monitor the condition of the fishing line in order to avoid its break at the time of work on the site, when a spare motor is at hand may not be.

Now you know how to tuck a fishing line for a trimmer to the coil of a trimmer for grass, and you can do it yourself without much effort!

How to refuel a fishing line for a trimmer to a trimmer coil for STIHL grass

How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction

Warranty production of the factory refueling of a trimmer for the grass will be in demand for fishing line substitutions. Having a very approximate idea of how to tuck a fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. How to wrap a fishing line for a trimmer to a trimmer coil for the grass, how to season a fishing line for a trimmer to a trimmer coil for grass. Autocut for a trimmer for STIHL FS 55 grass refueling the fishing line in a trimmer coil for grass 2 part winding of the fishing line on. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate this process.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

How to put a fishing line for a trimmer in a stihl mower.FS-38

He took out a mower from the barn, but there was no fishing line in it, I had to put a fishing line for a trimmer and took a small one in the occasion

Preliminary preparation

First, for winding the fishing line, it is necessary to remove the coil (bobbin, spool) from the trimmer for the grass. certain acts will depend on the difficulty of configuration and the type of product itself:

Small electronic trimmers for grass with a working location of the motor and coils at the bottom, usually have side buttons on both sides of the bobbin. With the simultaneous press on their highest part of the coil, coupled with the internal contents for winding the fishing line is disconnected, while the lower one remains on the trimmer. The analysis of the bobbin is better to create in an even smooth place, so that the spring does not jump out and not be lost;
Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, usually have coils with a special lamb: in similar structures, you should with one hand with one hand to hold the rogue in a motionless position, and the other counterclockwise twist the fixing bobbin on the staging barack. How to refuel a fishing line for a trimmer trimmer for grass? How to refuel a fishing line for a trimmer to a trimmer coil for grass. It is clear how to charge a fishing line for a trimmer for a trimmer for grass. After disconnecting the nut, the whole bobin is removed.
Electronic and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and with unhurried rotation, such mutual placement is achieved when the screwdriver enters the holes and the bobin is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

How to remove a mowing head from a trimmer for STIHL grass

Warranty production of the factory refueling of a trimmer for the grass will be in demand for fishing line substitutions. Having a very approximate idea of how to tuck a fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. How to wrap a fishing line for a trimmer to a trimmer coil for the grass, how to season a fishing line for a trimmer to a trimmer coil for grass. Autocut for a trimmer for STIHL FS 55 grass refueling the fishing line in a trimmer coil for grass 2 part winding of the fishing line on. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate this process.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The most ordinary option and a light sequence of actions:

The dimensions of the bobbin and the length of the unique factory winding determine the length of the fishing line recommended for winding. 2 5 m.
One end of the fishing line is inserted into the squeezer.located squeling fixing technological hole.
The fishing line for the trimmer is wound on the drum in reviting the spilles on the trimmer product direction. usually, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
The small section of the fishing line is left free to withdraw it out. it is fixed in the special side on the inside of the bobbin created to keep the winding when assembling a spool in working condition.
The left end of the fishing line is passed through the hole of the outer part of the bobin.
Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding.In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves.Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves.Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Automatic winding of the fishing line on the reel

There is a type of coils, in which the automatic mechanism performs winding without the help of others. it is quite only to correctly season the fishing line for the trimmer from the user. How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction. How to remove a coil from a trimmer for grass? How to wind a fishing line for a trimmer in in order to refuel a fishing line for a trimmer. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are tied through the hole on the outer case, the bobbin is assembled, and when rotating the winding button for the trimmer, the snitches are wound without the help of others. It is unrealistic to make the winding erroneous in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

Warranty production of the factory refueling of a trimmer for grass will inevitably require replacement of fishing line. Having a very approximate idea of how to fill the fishing line for a trimmer to the coil of the trimmer for the grass on their own, beginners are reluctant to take this matter. However, with some skills, the development of this simple science does not represent any difficulties, and the presented instruction below will facilitate this process as much as possible.

How to wind a fishing line for a trimmer to a trimmer coil for grass

Trimmer for grass is an excellent solution for those who have a large garden or lawn near the house, which must be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, there will be a need to replace certain elements, and this will have to learn.

How to do it? To replace the main cutting element, first you must choose the right it. In principle, in the operating manual for motorcycles, the diameter of the thread should be used in it.

When you purchased the necessary cutting element, try installing it correctly. It should be noted that on the Internet there is a huge number of videos that will help you figure out how to correct the fishing line for the trimmer to the coil of the trimmer for the grass.

How to change a fishing line for a trimmer on a trimmer

Below we have brought step.by.step instructions for replacing a thread of a trimmer for grass.

The first thing to do is disconnect the tool from the network and turn off the engine. Then it is necessary to remove the head of the trimmer for the grass. This can be done using a simple screwdriver lowering it into the gearbox hole to exclude the turn of the shaft. And then just unscrew

Removing the handle

Direct disassembly of the STIHL 180, begins with the removal of the handle, which is attached to the chainsaw housing using three rubber shock absorbers. To remove, it is necessary to remove the plastic plugs from the inner cavity of shock absorbers, after which with the help of a powerful screwdriver, squeeze the upper shock absorber first, then the one which is closer to the posterior handle.

A gas trigger is installed in the back of the handle, which is connected to the carburetor through the wire traction in order to disconnect the thrust from the gas trigger, it is necessary to unwind two screws and disassemble the handle.

When the handle remains on one shock absorber, it is necessary to turn the chainsaw housing from the inside of the handle and breaking to the side, remove the case from the last elastic band.

How to refuel a fishing line for a trimmer to a trimmer coil for STIHL grass

How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction

Failure of spark plug. an algorithm of action

The relatively high price of STIHL products can be scared away by many, but if you think about what is more important. reliability and good result or savings that are in harm with the quality? But, if you set out to save money, we offer you an option for the lawn mower with your own hands, collecting the device with your own efforts you will know all the nuances and the structure of the tool.

Of course, you can choose cheaper Chinese counterparts, but then no one can vouch for the result of the final work and for the life of the service, which is very short.lived among such models. So it is more profitable to purchase a mow from an authoritative company once, which is certainly Stihl, and enjoy stable work for many years of operation.

Trammers for grass professional and light

It is sometimes impossible to make a choice in favor of a device without elementary information on the main technical parameters of equipment that interested the user.

It will be advisable to compare these two categories of devices, choosing two from a number of models, on an example of which you can trace all their similarities and differences. The most popular model from the group of low.power gasoline trimmers STIHL is FS 55.

The devices that are popular due to optimal power and performance and used for processing large areas include FS 250. The main differences characterizing these two units are laid down in the constructive features of the engines.

So, in a household trimmer for grass FS 55, an improved type 2 MIX, which ensures a decrease in harmful exhausts and increases the efficiency of fuel consumption, is equipped with a direct drive shaft. The engine is working on the oil bosinzin mixture.

The engine power of this model is 1 liter. With., and volume. 27 cubic meters. cm, which allows you to successfully use it not only in the garden, but also on small lawns.

The duration of the average working session of this device is 2-3 hours of work in an area of up to 6 acres.

This is also facilitated by a tank for fuel with a volume of 0.33 liters.

trimmer, coil, grass, unscrewed, disassemble, assemble

The FS 250 device is equipped with a 2.15 liter with the previous model with a gasoline two.stroke 2 MIX engine. With. and with a volume of 40 cubic meters. cm.

The hard shaft and the piston group persistent to wear and significant loads allow the use of the unit in territories with an area of up to 20-25 acres for 6 hours of continuous operation.

Fuel container contains 0.64 l of fuel. The trimmer for the grass copes with advanced vegetation in any climatic conditions.

Most often, equipment of this type is trusted by complex communal work on the improvement of the territories of city parks and forest parking zones.

The similarity of the engines of these models is the presence of a smooth starting system Elastostart. This allows you to minimize uncomfortable jerk.shaped movements at starting, loading the muscles of the hands and back of the user.

The presence of the fuel pump for the trimmers in question provides the ability to pump fuel to the carburetor manually, which greatly facilitates the launch of the engine after a long break in operation.

The ergostrat mechanism, which is equipped with the FS 55 model, is responsible for the light and quick start of the engine thanks to the spiral spring in the design of the starting device.

The FS 250 unit is equipped with an anti.vibrational STIHL system, using special rubber linings of the extinguishing harsh shocks and fluctuations that occur during operation.

Due to this, the high efficiency of the operator’s long.term work is achieved without the sensations of fatigue and stress. Also, the structural features of the described trimmer for a professional class grass include a special regulatory authority. a compensator.

It prevents the saturation of the fuel mixture when filter pollution by harmful substances, providing a long.term period of operation. The surface of the filter surface is required to reach the level of pollution in 80 %.

Both of the under consideration trimmers are not inferior to each other in terms of convenience of use. The multifunctional handle present in the models is equipped with all the necessary controls, which gives the operation an operational and effective move.

Attention! The handle here is T-shaped, double, providing maximum maneuverability and adjustability. It is this type of handle that is optimal for frequent mowing of grass in vast territories

Equipment component by practical shoulder diluted belts with soft pads allows the operator to work for a long time without fatigue. These belts are also equipped with a convenient carrying system.

If necessary, it is possible to use portable belts with a tool bag and the mechanism of quick removal and fixing the trimmer for grass. All STIHL technique is necessarily equipped with special glasses that ensure the safety of the operator during operation.

The described trimmers for the grass are close and in their overall indicators. So, the STIHL FS 55 model has a length of 172 cm without equipment, and the FS 250 device is 177 cm. Without tools, the weight of a light model is 5 kg, professional. 6.3 kg.

Both units have a straight bar, cutting head Autocut 25-2, the ability to equip a GSB 230-2 with a two-blade knife and fishing line. The width of the herbs mowing is, respectively, 30 and 45 cm.

How to lubricate a trimmer gearbox for grass / Gearbox gearbox / Reducer Motokosa

Lubricate a trimmer gearbox for the grass at least once a year, but it is better to inspect the lubricant after every 20-25 hours of work or when the gear noise in the motorcade gearbox appears. How to lubricate the gearbox gearboxes. For lubrication, at first you need to clean the cork itself and the place around the traffic jam and the remnants of the grass, so that they do not fall inside the gearbox when filling it with grease. Then you need to turn out the cork for the lubrication of the gearbox (for example, the Echo lawn mower is a key for “17”, in Husqvarna-a 6-garnet on “5”, for Chinese lawn mower-the key on “12”). It is better to use the same manufacturer as your trimmer for grass or just from world-famous brands, such as Oleo-Mac, Stihl, Husqvarna, Oregon, Liquimoly, Litol-24, Azmol 158 and T.D., If only it was not a fake! The tube, if new, print, removing with your fingers a cork or piercing the cover with the back of the lid in the nose of the tube. Then we put a trimmer for the grass on the left side, and rotating the knife with one hand (so that the gears are smashed and the entire volume is filled), squeeze the lubricant from the tube with the 2nd hand through the hole inside the gearbox before its full filling. Then we twist and clamp the trimmer gearbox for the grass and a tube plug with a lubricant. If the lubricant is not in the tube (and, for example, in the jar), take a honey syringe without a needle, take out the piston, fill the lubricant (with your finger) in the syringe, and then fill the gearbox of the trimmer for the grass from the syringe from the syringe.

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

DIY: How to replace ignition coil and spark plug to a grass trimmer NAC

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections

Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

HOW TO FIX THE FUEL LINES/ FUEL LINES OF GRASS CUTTER/ BRUSH CUTTER/STRING TRIMMER/STRIMMER,

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

How to remove the coil and replace the fishing line for the trimmer

The owners of the trimmers, mainly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or fishing line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.by.step instructions given below.

Before refueling the fishing line for the trimmer to the coil, drown out the engine of motorcycles or de.energize the ethletric trimmer for the grass to avoid injuries that may occur in case of accidental rotation of the cutting tool.
Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, to twist the coil of the trimmer for the grass should be right, that is, clockwise.
Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
Cut the required amount of fishing line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the fishing line, since this will lead to increased load on the engine and greater consumption of gasoline.
Find the middle of the segment of the cord, folding it in half. You will get a loop.
Special grooves are cut out inside the coil (there may be holes). Insert the loop from the fishing line into this groove.
Wind a fishing line for a trimmer to a coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the fishing line about 20 cm long and fix them in the grooves located on the sides of the coil.
Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
Dress the lid and fix it with latches.
Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Tighten the coil of the trimmer for the grass will need to go to the left (against h. Arrows).

We offer to familiarize yourself with the tomato match characteristic and description of the variety

Two working antennae

In this type of squelpies, you should find the number of grooves for winding the fishing line lying on the inside of the coil:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding.In the presence of fixing grooves, the ends of the fishing line are threaded into them or hold the fingers of the free hand, spread into the through hole of the outer half of the bobin, the spool is locked and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves.Both strains of the fishing line are wound each on their own groove, fixing antennae and assembly of the coil is similar to the option considered above with one groove.

The 1st implementation of this procedure may seem to be long and quite laborious, but over time and experience, this problem will be solved significantly more freaky and easier.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Solving possible problems with fishing line

Most of the problems associated with the fishing line are similar to different trimmers and are solved in a similar way.

Turning the string

the presence of solid objects in mowing grass: branches, stones, etc.D., contact with which the string breaks off;
Powder of grass is close to the fence, and if it is mesh, then the fishing line for the trimmer is torn even faster;
low.quality cord. it is necessary to replace with a new reliable consumable;
wear of the output holes in the mowing head, as a result of which the fishing line for a trimmer breaks off from friction on the sharp edges of the bushings. it is required to replace parts with a new.

Large fishing line

Typically, a fishing line for a trimmer ends very quickly if you constantly knock a semi.automatic coil on the ground or press it with an effort to the surface. In this case, the head is unlocked, the cord is lengthened, and the knife cuts it. The second version of the fast consumption of fishing line is a trimmer for grass with an automatic coil is incorrectly used. If the mower regularly lowers the engine speed, the string is constantly lengthened and cut and as a result is quickly consumed.

The string does not hold

If the spring weakens the semi.automatic type in the coil of the semi.automatic type, the fishing line for the trimmer does not stay and is unwinded during operation. The cord is extended, cut off with a knife, as a result, the owner of the equipment notes that the thread quickly ends.

Advice! To check the tool, you need to remove the protective casing and start the engine. if the fishing line for the trimmer is advanced, this means that the spring must be changed to a new one.

a fishing line for a trimmer flies out

If the string flies out with kosbe, this is another evidence that the spring in the bobbin is weakened or completely lost with an inaccurate analysis of the head. As a result, the cord does not hold and pops up when rotating.

The string is not advanced

In the coils of automatic and semi-automatic cords, the cord is served without stopping the trimmer for grass. If this does not happen, then:

The fishing line for a trimmer in the head is wound wrong, so the coil does not spin;
The winding of the fishing line is made unevenly, so the cord stuck between the turns and does not go out. so that this does not happen, you need to wrap the thread carefully, preventing distortions, a turn to the turns;
The ends of the cord emerging from the holes are very short, centrifugal force is not enough to extract them, so the fishing line is not served-before turning on the trimmer for the grass, it is important to control the length of the thread and slightly lengthen it, if necessary;
The cord is stuck.

The coil does not spin

The reasons why the coil does not spin are similar to the lack of fishing line. This is the wrong or uneven winding of the string, its sticking, as well as the short ends of the cord, emerging from the holes.

Trimmer fishing line sticks together

If when working a fishing line for a trimmer sticks together, the main reason is the installation of a low.quality cord. In the course of work, the coil is heated, and a poor.quality string melts and glued. The second reason is the clash of the cord with solid objects. In this case, its sharp braking occurs, the thread is drawn into the head and picks up.

Advice! To avoid problems, you can apply mineral oil to the surface of the fishing line or, after winding on the head, spray it with silicone. A more competent solution will be the acquisition of a good high.quality head, which will forget about such problems.

So, replacing a fishing line for a trimmer on a trimmer will not be difficult if you know how to disassemble the coil and wind the cord winding. This process is similar for technology of different brands. A detailed description can be found in the instrument operation instructions or watch on the video.

Self.manufacture of bobbin

Quite often, a trimmer for grass is operated in the distance from places where you can purchase spare parts for a spitt with its breakdown. In this case, instead of a broken mechanism, you can install a simple coil made in design made by yourself. To do this, you need a sheet of plywood (textolite, metal, etc.), eyes, screws or screws. The process includes several stages.

A disk is cut out of the plywood sheet, which corresponds to the failed spool with a diameter.
A hole is drilled in the center of the disk, which matches the diameter with a shaft of a trimmer for grass.
Small eyes are attached to the opposite sides of the disk, which will serve to refuel the fishing line.
Through the eyes, pass the fishing line for the trimmer and fix it with ordinary screws or screws. The coil is ready for work.

Important! It must be remembered that to tighten or unscrew the nut without hard fixation of the shaft.

To replace the fishing line on a home.made bobin, you will have to release fixing screws, insert a new section of the string and tighten the fasteners again. It is not necessary to remove the coil from the shaft of the trimmer for grass, however, it is necessary to exclude the possibility of spontaneous launch of the motor.

So, above was step.by.step with the pictures described methods of repairing the string head. As you can see, the process is not complicated. And most of the breakdowns are directly related to the inaccurate refueling of the string and its unsatisfactory quality. You can clearly see all the stages of the process on the video.

Sources:

https://tehnostroiplus.ru/sad-ogorod/kak-razobrat-trimmernuyu-golovku.html
https://programka.com.ua/instrukcija/oborudovanie/kak-pomenjat-lesku-na-trimmere-jelektricheskom
https://programka.com.ua/instrukcija/oborudovanie/kak-snjat-golovku-s-trimmera-STIHL
https://domdetaley.ru/kak-snat-katusku-s-trimmera-STIHL/
https://domdetaley.ru/kak-snat-katusku-s-trimmera-stil/
https://domdetaley.ru/kak-snat-kosilnuu-golovku-s-trimmera-stil/
https://labequip.ru/kak-snat-kosilnuu-golovku-s-trimmera-stil/
https://xnb1a4ace.xnp1ai/nozhi/kak-snyat-katushku-s-trimmera-shtil.html

Grass Trimmer assemble, coil, disassemble, grass, trimmer, unscrewed