tiller on big wheels do it yourself

Features and device

Tracks for the tiller greatly simplify both the transportation of the load and the movement of the device itself. Due to the fact that the track mechanism covers a fairly large surface, the tiller moves much more evenly, exerts less pressure on the surface and does not get stuck on difficult soils. the tiller on tracks is able to work even in bad weather, and in good weather it becomes even more maneuverable.

The maintenance and use of the tracked module does not cause any particular difficulties for the owners, and it is not difficult to do it yourself. It should be borne in mind that when the tiller is equipped with a tracked module, its speed decreases. However, the device’s ability to navigate difficult terrain, transport goods and even clear snow from the area increases.

Tillers with tracked modules are otherwise identical to conventional tillers. The engine must be four-stroke with the ability to lock the axles so that the device can turn without making a whole circle. There is also a requirement for water cooling to cope with high loads that cause the motor to overheat. This type is more effective than air. The clutch system, gearbox and gearbox for tracked mechanisms are presented in the traditional version. The tiller on tracks is controlled by a handle.

When creating tracks on your own, it is important to understand that if you design them too high, the tiller’s center of gravity will change, and he will begin to experience difficulties turning, and even tilt to one side or another. To prevent such a situation, the second driven axle will have to be made longer by a couple of centimeters. Also, with the help of a bushing, it will be possible to expand the wheelbase already existing at the tiller.

How to make a tiller on tracks with your own hands?

• Features and device
• What can be done?
• Step-by-step manufacturing instructions
• Recommendations for use

Step-by-step manufacturing instructions

To make a caterpillar mechanism for a tiller with your own hands, in addition to the materials used, you will need certain tools: an angle grinder, and sometimes a drill, a boot knife and a set of screwdrivers, bolts, nuts and wrenches, a welding machine, wire, chains and a sanding belt. Of course, drawings will also be necessary, which are easy to find on the Internet in the public domain.

If homemade tracks are made from car tires, then the first thing the tires are freed from the sides to the state of a running belt. a track for caterpillars. This is easier to do with a well-sharpened knife, for example, designed for working with boots. The adjustment process is lengthy, but it can be accelerated by periodically smearing the blade with soapy substance.

It is more convenient to cut the sides of the tires with an electric jigsaw, which has small teeth. At the next stage, the wrong side of the tire is also corrected: excess layers are removed from it. This should be done when the tape is too dense inside. Such a track attachment made of car parts turns out to be quite durable, since the tire is initially closed, which means that it will be more difficult to damage the tracks during operation. Unfortunately, the available tire width will not give the user the opportunity to use a large surface. However, some craftsmen solve this problem by using multiple tires.

The simplest track module can be made from a conveyor belt and sleeve-roller chains. First, depending on how powerful the engine is, the required thickness of the used belt is selected. This is followed by the processing of the edges, which can begin to shaggy and, because of this, fail earlier. For this, a fishing line is used with a pitch of ten millimeters. The finished edges are then sewn into a ring, with a special hinge, or simply along the end parts.

Despite some primitiveness of the mechanism, it will serve for a very long time. It is important to add that the thickness of the tape must exceed seven millimeters, otherwise the device will not be able to withstand the required loads. The optimal interval is considered to be from eight to ten millimeters.

The track module can be made from belts if they have a wedge-shaped profile. It is best to connect the parts with a lug, which is fixed on the straps with screws or rivets. Another common solution is to construct tracks from chains of equal size. Such a versatile part, as a rule, is abundant in any home workshop, so this method is also economical. To make caterpillars, you have to take a pair of equal chains and unclench their extreme links.

Now the two chains can be connected into one circuit, the links can be clamped back and for reliability everything can be welded. For greater strength, the chains can be fastened again with lugs, which, by the way, are also simply made from scrap materials. metal sheets of the required thickness. In general, this part can be not only steel, but wooden and even plastic. In the latter case, wood bars or plastic tubes are used as it. Which material will be most suitable can be determined depending on the purpose of using the tiller.

In the case when the cargo expected for transportation does not differ in large weight, the lugs should be made plastic. The same applies to moving devices equipped with weak motors. When the tiller is planned to be used as a tractor, and it has a rather powerful engine, steel parts should be preferred.

Sometimes homemade caterpillars are reinforced with pipes, which are welded together. Parts in this case are made of metal and have a rectangular cross-section. In this case, it is recommended to remove the drive shafts from the “Oka”, and take the spline part from the “Buran”. The equipment must be equipped with brakes that are mounted on the front shafts. This addition allows you to get a device with maximum capabilities.

It is worth mentioning that in order to convert a regular tiller into a tracked one on the go, you will first have to put two additional wheels on it, one on each side. The result should be a four-wheeled structure, on which the tracks are already put on. Some craftsmen prefer to make these additional wheels removable rather than weld on new mountings. This can be accomplished by attaching the wheels to the axle using a flexible or rigid transmission. It is impossible not to mention that it is not necessary to make the tracks yourself. no less economical solution would be to use parts from old equipment, for example, “Buran”.

What can be done?

When choosing material for tracks, it is important to consider that it should not be excessively heavy. Since the tiller itself does not have a powerful engine, it simply cannot cope with weighty material and, most likely, will break. The caterpillar mechanism, as a rule, is made of motorcycle tires, chains, pipes, belts, or a conveyor belt in combination with a sleeve-roller chain.

Most craftsmen create tracks from tires. these parts are easily converted to the desired design. It is necessary to choose tires for large trucks, taking into account the existing tread pattern and shape, because the correct pattern will improve grip. It is better if these are spare parts that previously belonged to tractors or other large-sized models.

A properly selected tread will be able to make good contact with wet ground, ice-covered and snow-covered surfaces. In addition to materials for the tracks, a tiller with a gearbox, as well as a pair of additional wheels, will be required to construct a full-fledged device. If necessary, an additional cart is attached to the tiller and, if desired, even on skids to transport goods in deep snow.

Recommendations for use

When using the tiller tracks, it is necessary to constantly check how well the chain is tensioned, and also regularly oil the parts whose friction occurs during movement. In addition, it is recommended each time before use to check whether any damage and breaks have appeared on the chain. After the trip, a routine inspection should also be carried out in order to detect any damage or broken hooks in time. When using the tiller, you should avoid driving over roots and stone massifs, as well as hemp, otherwise the track module will be torn very quickly.

For an overview of the tiller-all-terrain vehicle on tracks, see the following video.

Wheels on the tiller, which fit and how to put it yourself

• Methods for attaching car wheels to tillery. What wheels are needed for a cultivator.
• Choosing wheels for a tiller and do-it-yourself replacement
• Criterias of choice
• Do it yourself

Having become the proud owner of a light tiller with a 6.5 hp engine. the first season will be a test for everyone, all the pros and cons of factory performance will be on the face, to understand this you do not need a lot of experience. Truth is learned in action.

We will talk about the wheels. the set includes most often herringbone chamber tires on light rims of the 8th or 10th diameter. These wheels are actually rather weak. insufficient weight, I consider lightness a disadvantage. Installation of additional weights is required. The width of the tire is narrow, the permeability is low. the tiller slips and buries on a wet surface. To travel long distances outside your vegetable gardens, be patient. the speed is low. Tire production China. enough for one or two full seasons, these tires burst along the side under heavy loads, while the tread itself remains unchanged. Simply put, “oak” rubber for sale.

Alternatively, you can use car rims, wheels. We choose the diameter according to the principle. what is in the garage))) A plus will be the presence of a good mud protector. The higher and narrower your wheel is, the more comfortable it will be to control the tiller, the ride will become softer. The clearance will increase. this will be a huge plus.

The rework process itself does not take much time. The presence of a special tool is not required.

Step by step: unscrew the hubs from the factory wheels. usually these are bolts and nuts (12-13)

Next, we fix them with the help of more durable bolts and nuts on a turnkey basis by 17 to the disk from the car, having previously drilled more holes in the hubs. We select discs according to the number of holes on your hubs (4-5)

We check whether the cotter pin is freely inserted to fix the hub through the extension. The track will become wider, we check if the new wheels touch the parts and parts of the tiller, in this case the wings

Excellent weighting materials. weights will be obtained from old brake discs

We install them if it is necessary to transport a heavy load, or for earthworks for plowing and hilling. On these wheels, the tiller easily copes with the tasks set, the experience of the first season shows that this rework will be!

All ingenious is simple! Oh, if only the protector is like on a tractor. but this is the next topic for conversation in future articles. By the way, the market offers tires with a tractor pattern of a larger diameter. R12,13,14,15. The price tag is correspondingly high, whether it is worth it or not is up to you. Successful alterations, light outdoor activities on your hacienda. tiller to help you)

Thank you for reading to the end? Like it? subscribe to the channel.

Installation of Zhiguli wheels on a factory trolley for tiller1

Choosing wheels for a tiller and do-it-yourself replacement

When purchasing a tiller on a farm, people focus on engine power and equipment performance. However, the performance of the unit is directly affected by the wheels for the tiller. The undercarriage allows the unit to move around the personal plot.

Factory models are usually equipped with a suitable wheelset. But given the loads on this structural element, the wheels often break. Accordingly, the farmer has to buy the failed part on his own.

We will advise you on how to choose the right wheels and suggest DIY options for making a running gear.

Methods for attaching car wheels to tillery. What wheels are needed for a cultivator.

put the tiller on wheels from the car

that’s what happened

Wheels for tiller. Do-it-yourself lugs.

Criterias of choice

• Pneumatic. Such products have a rubber tire and a camera.
• Rubber. One-piece construction that consists of a rim and durable rubber.
• Grousers. Metal elements aimed at increasing the cross-country ability of vehicles.

The complexity of the choice lies in determining the operating conditions of the equipment. For example, for working on clayey or wet soil, it is recommended to use lugs.

a tiller equipped with conventional rubber wheels will not perform well in difficult conditions. In addition, attention should be paid to the wheel radius and tread pattern.

Wheelsets belong to the category of quick-change equipment, so it makes sense to purchase two types of chassis. For example, lugs and pneumatic wheels. This will allow you to work with equipment in different weather conditions.

What wheels can I put on a tiller? Much depends on the intended use of the technique. If the unit is needed for planting and harvesting work, you can stop on pneumatic wheels.

These products are ideal for working on soft ground. The recommended radius is about 40 centimeters. At the same time, we recommend choosing wheels with deep tread, which will increase maneuverability and cross-country ability.

For primary cultivation of virgin land and soil with increased m stones, it is better to use cast wheels. They practically do not receive mechanical damage due to the lack of an internal chamber.

However, such elements have increased weight, therefore they are installed on medium and heavy tillers.

The lugs not only increase the vehicle’s cross-country ability, but also increase its productivity. The tines enter the soil, which creates additional force to move the machine in a given direction.

Such elements are used mainly for arable work on large tracts of land. It is impractical to use lugs on a small personal plot.

Do it yourself

Now let’s talk about how to make the wheels for the tiller yourself. Let’s clarify right away that the creation of pneumatic and cast wheels at home is, in principle, impossible.

And why reinvent the wheel when you can equip garden equipment with tires from a car or motorcycle. You just need to install a suitable hub and you can get to work.

Another thing is when it comes to lugs. Such homemade wheels for a tiller can really be made by yourself. Here’s a basic assembly diagram:

• We take old disks from the car. Please note that only the rim is needed. The diameter of the wheels depends on the power of the tiller, given that the design will be all-metal, the weight will be considerable.
• We weld metal plates to the discs. The edges of the plates should touch the edge of the rim. This is an important structural element, therefore the plates are welded along the entire outer radius, you can fix them with bolts to increase reliability.
• We weld the teeth to the metal plate. They can be made from a corner, after cutting it into pieces of the desired length. Please note that the distance between the teeth should not exceed 15-20 centimeters. Otherwise, the efficiency of such wheels will be reduced to zero.
• We weld the axle shafts into the disk, supplement the structure with bearings and install the chassis on the tiller.

You can make lugs from an old gas cylinder. In this case, you need to cut out two rims, about 6-7 centimeters wide, and then proceed according to the above scheme.

In general, lugs can be constructed from any material at hand that has the shape of a circle. The main thing is to show desire and apply a little skill.

Engines to tillers

Being the best choice, the diesel engine is distinguished by long working life (even at low displacement), maximum power and low cost in terms of refueling. Single-cylinder engines on 4 wheels have good power with low fuel consumption.

Chinese Tiller Diesel Engine Device

Engines of two competing countries. the USA and China. are in demand. They practically do not differ in quality, but there are significant differences in the price category. In order to save money, it is better to give preference to Chinese models, the leading of which are:

You should pay attention to Honda and Agromotor, which have excellent performance, high quality and availability.

Features of 4 Wheels Diesel Tillers

tiller is an indispensable assistant at the summer cottage of gardeners and truck farmers. There are 2 types of such special equipment: gasoline and diesel tillers. Diesel tillers on 4 wheels are preferred due to their economy and maneuverability.

Cons of tillers

Diesel tillers on 4 wheels also have disadvantages, including:

• increased cost (compared to a gasoline engine);
• expensive repairs;
• noise and vibration during unit operation;
• emission of more exhaust gases.

Heavier models limit the tiller’s maneuverability, and units with larger dimensions need some space.

Features and Benefits of Tilers

Diesel cultivators are powerful heavy tillers, adapted to work on difficult and hard ground. Equipment weighing 100 kg is equipped with an internal combustion engine with a capacity of 9 horsepower or more, as well as a full-fledged gearbox.

Homemade 200cc WHEELBARROW !? PART 1

The volume of the fuel tank is 4–8 liters. In many models, the distance between the wheels and the height of the handles are adjustable. Special equipment provides for a disc clutch and a gear reducer. Diesel four-wheel models are used for plowing and cultivation, pumping liquids and moving loads, digging up root crops, etc.

Operation of a four-wheel diesel cultivator

The advantages of diesel technology:

• power indicators are higher than that of gasoline;
• reliable engine cooling system;
• advanced functionality;
• ease of use.

Formation of four wheeled tillers

Dump

The dump is necessary not only for removing snow in winter, but also for clearing various debris. To make it, we need ordinary sheet metal, the thickness of which will be about 2 mm. Inside it you need to weld 4 ribs of the same steel, but about 4 mm thick.

They need to drill holes through which the blade with the rods will be attached. The lower part of the structure is best sheathed with sheet metal to prevent the blade from burrowing into the ground.

Build a Cargo Tractor 168cc 6.5HP

The disc hillers must be attached to a homemade cart with wheels. They are made from ordinary sleeves and pipes, welded together.

Attachments to tillers and motor-cultivators, homemade products of which you can completely make yourself, are of various types:

• Weeding equipment.
• Potato diggers and potato planters.
• Snow blowers, etc.