Trimmer for grass stalls after a short work. Stalls a trimmer for grass on idle…

Trimmer for grass stalls at idle reasoning

A braid braid with a gasoline drive is a useful thing for owners of personal plots, lawns, and when a trimmer for grass suddenly stalls, the work on cleaning the territory stops from the grass. The device itself is a rather complex mechanism, so there are many different causes of its breakdowns. The most common problems contain instructions for operating. Know the reasons why the trimmer stalls for the grass, it follows to independently effectively perform the repair of the device.

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

• the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
• the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
• mechanical damage to wires, tubes, hoses;
• The ignition chain.

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

Read does not start a lawn mower of the video

A gasoline braid for grass does not turn a cold

It is not recommended to press gas when starting a cold engine. Tilting the brush so that the air filter is on top, press the fuel absorption button 5-6 times, install the functional lever to the Start position, pull the starter’s cord several times to run the engine. After a few seconds of engine operation, turn off the start system.

Gasoline does not start hot

If the bureau has worked recently and has not yet cooled down, but does not want to start, press the gas trigger, pull the starter abruptly several times until the engine starts, and only after that release the gas trigger hook. If a lot of time has passed, and the brush has cooled, it should be launched as if it were cold. If the above methods did not help, the cleaner has not started, then you should contact the service center.

• Blog
• About the service center
• Brands are served
• Diagnostics and price repair
• Delivery
• Spare parts
• Contacts

Specialized service. Complex warranty and post-warranty service of garden and communal equipment from world manufacturers! We sell spare parts with delivery throughout the braid for grass. A useful thing for owners of personal plots, lawns, and when a trimmer for the grass suddenly jams, the work on cleaning the site from the grass stops. The device itself is a rather complex mechanism, so there are many different reasons for its failure. The most common problems are contained in the operating instructions. Know the reasons why trimmers for grass grass should be able to effectively repair the device yourself.

Diagnosis of the candle channel

What to do if the used fuel mixture is in perfect order, but a trimmer for grass is still not started by gasoline? The reasons for the refusal of the mechanism may lie in excessive moisture of the candle channel. To diagnose and eliminate the problem, it is necessary to do the following:

• To twist the candle. Wipe it thoroughly, and then dry it.
• Drain excess fuel in the chamber through the corresponding candle hole.
• Clear the old candle if there is a dozen on its surface. Cope with the task will allow the use of a conventional ladies’ nail file or file.
• When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
• Collect a functional block back.
• Try to start a trimmer for grass.

It is recommended to perform a candle channel to dry for at least half an hour. However, in no case should you resort to the calcination of its elements. After all, heating the spark plug can lead to its final corruption. Что предпринять, если обслуживание функционального блока было выполнено в соответствии вышеуказанным рекомендациям, но триммер для травы не заводится, искра есть при этом? In this case, it should be treated with gasoline threaded connection. The latter does not need to be saturated abundantly fuel. It should only be slightly moisturized. Resort to such actions should be to ensure the ignition. After all, no matter how much the candle gives a strong spark, in an absolutely dry chamber there simply will not be something to ignite.

Even more information about the repair and choice of tools on our website www.Looktool.Ru, we are happy for everyone.

If even in this case a trimmer for grass does not start, it is worth evaluating the quality of the contact between the high.voltage wire and the candle. In the absence of a spark (in the presence of a reliable connection between the indicated elements), most likely, the problem is caused by breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the knot.

Asseting device and common malfunctions

The easiest way to give the lawn mower for repairs, allocating a certain amount of funds from the family budget, operational and high.quality repair with your own hands is no less simple and convenient to understand the design of the lawn mower and fix all the problems.

The massive and piece manufacture of trimmers is based on the use of generally accepted technology, the typical design scheme consists of certain elements and parts, it is important to know them when carrying out independent repair work:

• top part. The basis of the entire structure, where all important elements are collected, such as the starter, carburetor and the engine of the lawn mower;
• middle part. Hollow rod, inside it is a cable connecting the engine and gearbox, which sets the cutting fishing line for the trimmer. In this part there are mounts for the distribution of weight of the entire structure and a belt for fixing a trimmer for grass on a belt of a person using a trimmer for grass for its intended purpose;
• Bottom part. It has a gearbox and cutting elements that are hidden under a practical casing, which protects the user. The casing provides an increased level of safety, preventing large fractions of garbage, pebbles and glass in a person while working with a gas station.

The most common and often encountered, subject to independent correction of the breakdown of the unit can be called the following problems:

• engine malfunction, due to which the lawn mower is not started and does not work;
• enhanced vibration of the bar motorcosa, which complicates its targeted use;
• increased overheating of the gearbox, its accelerated heating during operation;
• slow and weak functioning of the cutting fishing line at insufficient speeds;
• the clogging of the starter grill causing the engine overheating and its refusal to work;
• rapid and frequent clogging of the carburetor due to the use of poor.quality fuel;
• clogging of the air filter in case of non.compliance with measures to care for the device.

All these problems can lead to the fact that the device will lose its ability to work before ordering the necessary spare parts for non.bosomeds should be carried out by a visual inspection and diagnosis of the device.

Special attention is required by individual spare parts and assemblies of the device, to verify them, you will not have to turn to a professional master, a complex of diagnostic measures will help to identify a consequence of the occurrence of a loss of performance.

Features of diagnosis

A well.posed question is already half the answer. The fact that the gasoline trimmer for the grass or the lawn mower stalls, namely, will significantly accelerate the search for a solution

• immediately after the start;
• when it works for some time idle. after one or several minutes;
• when pressing the gas button (or handle). or shortly after the start of work at high, submasymal speeds;
• under an enhanced load (for example, to cut the bushes, mow thick and high weeds);
• when warming up in the cold, it heats out excessively (the lawn mower stalled around overheating);
• After the opening of the air damper.

Depending on which of the circumstances was clarified during the pre.diagram, the exclusion method is looking for a more specific reason for the malfunction of motorcycles or a trimmer for grass.

With an increase in speed

If the lawn mower (or a trimmer for grass) has stalled when the engine speed is added, check the device according to the following signs:

• clogging or sticking a valve built into the gas tank cover;
• valve adjustment violation;
• A failure in the work of pistons and cylinders. from vibration during the work of a braid for grass or a trimmer for grass, random blows directly in the session of the mowing of grass;
• violation of the supply of fuel mixture;
• excess air pumping into the motor;
• cracking of the fuel intake hose, weakening its compounds.

When the fuel.heating mixture is served with the right portions to the engine in a timely manner. it burns the amount that has managed to enter from the moment of the last gallpling, and he stalls again.

Features of diagnosis

A well.posed question is already half the answer. The fact that the gasoline trimmer for the grass or the lawn mower stalls, namely, will significantly accelerate the search for a solution

• immediately after the start;
• when it works for some time idle. after one or several minutes;
• when pressing the gas button (or handle). or shortly after the start of work at high, submasymal speeds;
• under an enhanced load (for example, to cut the bushes, mow thick and high weeds);
• when warming up in the cold, it heats out excessively (the lawn mower stalled around overheating);
• After the opening of the air damper.

Depending on which of the circumstances was clarified during the pre.diagram, the exclusion method is looking for a more specific reason for the malfunction of motorcycles or a trimmer for grass.

In the process of warming the engine

If the engine heats up too fast, overheating. a lawn mower or a trimmer for grass works unevenly, as if jerking. After which she stalls. The reason may be as follows:

• boiling gasoline;
• The ignition wire was damaged (poor insulation);
• The coil in the ignition system has noticeably burned out, inter.seal circuits appeared.

The same heating is observed when using rotary (not disk) damper.

With gazeaming

You click on gas. and the trimmer for the grass stops working, does not develop momentum. The following alleged reasons are possible:

• The tuning of the carburetor was lost, which appears with an increasing load on the drive itself. after its long downtime or when working in extreme conditions;
• The fuel valve is clogged with deposits;
• The carburetor cable is weakened and sag;
• Excessively stretched, possibly torn off the fuel supply hose;
• The check valve (sapun) clogged with deposits. fuel does not enter the tank with fuel.

Important! Problems in the carburetor itself give themselves out the vibration of the lawn mower

When working idle

Having launched a trimmer for grass or a motorcycle at idle, you find that the device is starting up. but it swallows, after working, say, 5-10 minutes. The reasons here may be as follows:

• clogging, violation of carburetor adjustment;
• Initially incorrect configuration of the valve mechanism of the carburetor;
• air filter clogging;
• reducing the speed of the gearbox (if any). the incorrect ratio of the fuel mixture;
• clogging the throttle;
• penetration of excess air into the fuel system;
• The fuel ends in the tank (and oil in the tank, if the engine is four.stroke).

If there are problems directly with the carburetor, the machine will stop both after a cold start and after launch on the already worked engine.

Checking performance

Before the diagnosis of Magneto, you need to make sure that the problem is actually in this node. To do this, check the entire chain and make sure that there are no other reasons for the breakdown of the trimmer for the grass.

• First, you should carefully examine the coil for the presence of cracks and other external defects on the case. Next, you will need to study all the elements and nodes conducting the current and make sure that they are clean.
• The next step is the inspection of high.voltage wires. They must be working and reliably attached to the contacts, without traces of rust and with intact insulation.
• The next action will be checking the candle cap. As a result of careless actions, the user often tears it off from the high.voltage wire, and then improvises and creates a home.made mount. You need to understand that any poor.quality connection in this place significantly reduces the power of the electric arc of the candle.
• Then you should make sure that the candle itself is working. If you refuel a low.quality motorcycle with gasoline, the service life of this part is significantly reduced. In addition, it can be flooded or have a large incapacitance that prevents work. Sometimes the candle even takes up and does not unsc.
• Next, you need to inspect the circuit switch. On trimmers and chainsaws of Chinese.made, it very often breaks.

Replacing the seals of the Chinese trimmer for grass.

One of the main causes of air leaks into the engine are crankshaft oil seals. In general, this problem is the most common on Chinese trimmers, and in some cases, seals begin to pass the air in the first year of service. All the fault of low.quality rubber products of such mowers, well, no one has canceled natural wear.

Essle for different sizes were installed on both sides of the crankshaft (12227mm small and 15307mm large). You can safely sin on the seals if it begins to “snot”. Another indicator of their malfunction is floating turnover when working for “hot”. Next, we will consider in detail the process of replacing.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

• The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
• The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
• Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

The lawn mower stalls at high engine speeds

During use, a situation appears when, when you press the fuel consistency button, the speed of the aggregate begins not to increase, but to decrease. The malfunction of such a disposition can be caused:

Fuel hoses for a filter

• Etching of atmospheric air into the combustion chamber;
• Difficulties with the circulation of fuel consistency;
• Clogging of the soundtrack in the lid of the gas tank (cleaning the hole with a narrow sewing needle);
• Incorrect adjustment of the carburetor.

When air leakage when I operate the internal combustion engine, you need to check the density of the pipes and the integrity of the gaskets in the CPG. A non.circulation of fuel consistency can be solved by the method of eliminating blockages in fuel pipelines leading to the carburetor. If a vacuum appears in the tank and the fuel mixture does not enter the carburetor, rather clean the soundtress with a narrow needle and blow it with air.

Elimination of the reasons why the lawn mower is not started

The fuel mixture should be prepared with accurate observance of gasoline and oil proportions. In this case, you cannot use another brand of fuel. To exclude dirt, gasoline should stand in a glass or metal dish 2 days. Cannot be used for storage of fuel plastic dishes. Distribute the oil with a medical syringe without a needle. Use only a freshly prepared mixture, without leaving an unexplored fuel in a tank. If the engine is capricious, the lawn mower stalls, when you press gas, it may be guilty of fuel.

If the step-by-step algorithm for searching for a malfunction has not given a result, and your braid for grass still does not start or stalls, it is worth examining the carburetor and the engine itself. A clogged carburetor can become one of the reasons, unstable operation of the tool. Three main problems can be distinguished here:

• Clogging of channels or nozzles. All this is cleaned with special flushing or blown by a powerful stream of compressed air from the compressor. Do not use needles and wire, so the passing sections can be damaged;
• Wear of the carburetor laying. Trimmer for grass stalls when you press the gas. Output. replacing the failed laying;
• Violation of tightness. To check this indicator, you can use the usual household tonometer, replacing the pressure gauge on it with the right. A trimmer for grass is not started a gasoline dry candle. Garden gasoline trimmer rating. Follow the testimony: if they do not change, everything is fine, and since the pressure will begin to fall, then some part of the carburetor is faulty. Will have to find it and replace it with a new.

If everything is in order with the carburetor, then the gasoline trimmer for the grass may not be launched due to wear of the piston group. If chips, scratches or bully are found, on the piston or cylinder they should be replaced. Piston rings are subject to mandatory verification. A small rally piston when swaying the connecting rod indicates that the time has come to change the rings. This procedure is best entrusted to the specialists of the service center.

What to do if the lawn mower or saw stalls at high speeds (under load)

Group for repairing garden equipment Video about the reasons for the sudden stop of a two.stroke.

The lawn mower does not start hot. press the gas trigger and pull the cord abruptly several times until the engine earns, then lower the trigger. Not starting. specialized repair is required.

Checking the ignition system, if the lawn mower is not started, is carried out sequentially:

• Clean the removed candle from soot and dirt, dry, set a gap of 1 mm;
• Connect to a high.voltage wire and check on a spark, twitching a few times;
• In the absence of a spark, check the high.voltage wire for integrity;
• replace the candle;
• dry the candle channel;
• At the same time, the operation of the ignition coil is checked, it is faulty if the working candle does not spark.

It is in the case of a malfunction of the ignition coil that the lawn mower does not start hot, stalls, works with interruptions.

Cleaning or replacing the air and fuel filter will provide the necessary consumption of ingredients entering the carburetor. Air filter can be washed in soapy water or replaced. If the nylon canvas is used, it is washed, the porous felt filler is replaced. Why does the lawn mower stall when you press the gas: the causes and their solutions. The lawn mower stalls (trimmer for grass): the fuel filter is carefully changed, without leaving an open suction pipe. Whether the replacement of the air filter is needed, it is possible to determine if the engine with the air purifier removed is launched. Whether it is necessary to change the grid on the fuel supply, if the lawn mower is not started, a dry candle will tell.

Sapun, a hole for air intake into a gas tank. If it is clogged, discharge is created in the tank and the mixture does not enter the carburetor. The hole can be blown with air or cleaned with a needle. Clean the exhaust channel, remove the anti.icper mesh of the muffler.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

Read gasoline trimmer for grass Brait 520 Videos

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

• clogging or clutching a valve located on the gas tank lid;
• The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
• problems with the circulation of the fuel mixture;
• atmospheric air
• The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

The lawn mower stalls in other words suffocates when pressing the gas

If the inconsistent is associated with the carburetor node, then it can be recognized when the lawn mowing appears when the vibrations appear. When a hose bursts or a cable stretches, a change of data data is made.

When a braid for grass stalls at large speeds, this is due to the following problems:

• clogging or clutching the valve placed on the gas tank lid;
• The carburetor was drained under the influence of vibrations that occur during the operation of the mechanism;
• obstacles with the circulation of fuel consistency;
• atmospheric air
• The hose created to fuel fuel cracked or slightly connected.

The carburetor is regulated by focusing on the operational annotation to the trimmer. For the option, it is often enough to weaken the tightness of its body. If there are problematic issues with the circulation of the fuel consistency, then it can gradually enter the carburetor. After its production, the engine stalls at huge speeds.

At single speeds, all.fought trimmer stopping the grass are subsequent:

• pollution, drainage in another incorrectly configured adjustment of the carburetor;
• clogging of the air filter;
• reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel consistency;
• clogging of the throttle;
• air entering the system;
• insufficiently fuel at the work of a lawn mower.

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

The unit can stall immediately after starting, if the carburetor is resolved as it was also called incorrectly configured. this causes an uneven supply of fuel. The result will be that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting by annotation to the mechanism.

Filters

Blocking air filter ─ another reason for the unreliable operation of the device. To check the involvement of this element in the malfunction, you need to start the lawn mower without it. The contaminated filter can be washed in gasoline, dried or replaced with new.

The clogged fuel filter does not let the fuel into the cylinder, and the engine with full gas stalls due to elementary lack of gasoline. This element is located inside the tank on a fence hose. To eliminate the problem, instead of the old filter, put on the new hose or rinse carefully the one that was removed.

Advice! When trying to pull out a cork in the tank, the hose along with the filter can fall into the tank. You can get them with tweezers.

What to do if the lawn mower starts and stalls?

Now we will consider all the above problems described in more detail.

In principle, the reasons why the engine of motorcycles stops working when pressing gas can be a huge number. Here we will consider only the most common.

Perhaps the air damper just clogged. And to eliminate the problem, it will be enough to simply clean the air damper. The engine also stalls due to the clogged air filter. To clean it, the filter should first be washed in the solvent, and then blow the stream of compressed air.

A similar procedure should be carried out with the clogged fuel filter, which prevents the intake of the fuel in the proper volume with an increase in engine speed.

The engine can stall for other reasons. Firstly, the spacer is worn between the cylinder and the carburetor, and secondly, the crankshaft oil seals began to suck in air.

We have already indicated that in this case the problem is in the carburetor. In it, due to increased temperatures, gasoline begins to boil, which is why the air-fuel mixture ceases to form or its quality is critically reduced.

In addition, this problem may arise due to the fact that the carburetor is equipped with a rotary rather than a disk damper. If the problem has acquired a chronic character, then it should be solved radically. by buying a new carburetor with a disk barrier.

Most likely, access to the fuel tank is difficult or completely absent, which is why a reduced pressure zone is formed in it, due to which the engine stops receiving fuel in the required amount and because of this you stop working.

The engine at idle can stall for the following reasons:

News ONENEN ONENEN ONENY ONENY ONE ONE ONE

LSI and began to prepare not quite normal gasoline solution, which is why they began to fall on the drum;

You will need spare parts to eliminate most problems, and the Well Part will be ready to provide them with the best cost to you.

Why stalls the chainsaw

If the chainsaws start and stall, the reasons can be different. An external inspection should be carried out before attempts to fix the tool.

If the saw stalled during operation, you should check the presence of a mixture of oil with gasoline in the tank. If the fuel mixture is over, the device will not work. In those situations where gasoline still remained, the quality of the tool should be evaluated until the moment of is turned off. The occurrence of extraneous sounds and the subsequent sharp stop should alert.

The formation of soot on electrodes can also cause difficulties in the operation of the tool. Carefully inspect the device, clean if necessary.

When pressing gas

In cases where the chainsaw stalls when you press the gas, you should check the silencer and the fuel filter. A possible cause of problem is a violation of the tightness of the fuel hoses. In some cases, the addition of revolutions helps.

Sometimes checking all the details does not give a result, the tool is suffocating, zooiling when gas is added. If the device stalls when a person presses gas, it is possible to supply fuel in insufficient amount for normal operation. This phenomenon occurs due to clogging of the carburetor or filter.

Damage can occur due to clogging with air filter dust. When you give gas, the device stops working. Do not eliminate the problem yourself, since each model has individual characteristics.

Calling may cause failure or lack of lubrication on the chain of the chainsaw. If the circuit is dry, the channels should be cleaned through which the oil is supplied to the device tire. If the oil proceeds, the presence of cracks, defects on the pipes is noted, you need to treat them with sealant.

Under load

In situations where the device stalls at load, the problem can be with a gas tank or filters. Check the quality of the fuel and change the filter.

Often the saw does not gain momentum due to the fact that the mixture flooded in the gas tank has a low octane number. There is not enough power, sufficient heating does not work, the chainsaw stalls under load.

Often, malfunctions of the component parts lead to the fact that the device stalls under load. You should check for the presence of a sucker hoses, seals, gaskets. If the details are faulty, you can try to fix them or replace them.

In cases where the chainsaw is started and immediately stalls, the fuel is not enough, the device does not heat up. Turn the device

It is important to use a suitable mixture. Different types of fuel are better suited for different models

It is necessary to familiarize yourself with the instructions, recommendations, reviews of people whose device works normally

It is necessary to familiarize yourself with the instructions, recommendations, reviews of people whose device works normally.

At idle

In those situations where the chainsaw stalls at idle speeds, it is necessary to examine the state of the muffler. If the part is contaminated, the spent gases are poorly displayed, the engine cannot continue to work, stops.

The saw stalls idle and in cases where the carburetor is incorrectly configured. It is better for beginners to fix the repair to specialists, since there is a chance of incorrect setup, because of which the tool will not be able to work. Tachometer is required to adjust the carburetor.

At high speeds

If the device stalls at high speeds, pay attention to the state of gasoline and air filters, the serviceability of the fuel hoses

Polluted air filter can be washed under warm running water

It is important to thoroughly dry the part before installing it so that the water does not violate the serviceability of the tool

If the liquid stops flowing through the fuel hose, it clogged. You can clean the part or replace with a new.

In cases where the saw stalls at large speeds, but the liquid flows through the hose, and the air filter is clean and working, look for the cause of the breakdown in the fuel filter. Install a new one in its place or clean.

In some cases, the problem is hidden in a gasoline pump. With the wear of the component part, the fuel begins to flow through the walls. If this phenomenon is noted, a new pump should be installed.

When tilted

If the saw does not develop speed when tilted, turns off, stops working, you need to check the fuel level in the tank. If it is not too high, the device is not supplied in an inclined position is not supplied with a sufficient amount of fuel, since the fuel tube is above the mixture level.

The causes of the malfunction and their elimination

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

Why does a trimmer for grass stall when you press the gas?

As you can see, the reasons why the trimmer for grass can stall when pressing for gas, a lot

That is why it is important to monitor the state of your assistant, to check the condition of all systems of the mechanism in time

Before you understand why any of the instruments of a summer house or a professional working with a motorcycle (benzocosa) stalls-it is worth distinguishing between two main situations when it happens. First, this is when the tool does not start after you have made the purchase, and the second. being in operation. So, we will analyze both.

• After starting.The case stalls the case if the carburetor is incorrectly configured or it was swollen. Fuel is supplied unevenly, respectively, distinct vibrations occur.
• When heated. The situation when the mechanism starts and works, but gradually “chokes” and stalls on the go. when gasoline boils in the carburetor, or the damper in the carburetor is not disk, but rotary view. In such cases, it is better to replace the carburetor itself. There is an air leakage option. when a coil or wire is broken in the ignition.
• At high speeds. This also occurs from the rounding of the carburetor or clogging the lid on the gas tank. It is worth trying work with a slightly parted valve. Be sure to check the fuel intake hose. it can be a crackling or poorly attached to the base.
• He is not gaining momentum. As the main reason why the engine is not gaining momentum. an air filter clogged. It is possible to subside a cable in a carburetor, a breakdown of a carburetor and the occurrence of problems with the motor drive mechanics.

There are times when the detail of the mechanism requires mandatory replacement, so we are always happy to offer spare parts for the lawn mower

It is important to understand that sometimes saving on minor elements can lead to a breakdown of such global components as a carburetor or engine. Therefore, competent operation and timely replacement of the necessary particles will provide you with full work with pleasure

Little tricks

If you are unable to twist/loosen the adjusting screws normally, perhaps the matter is too thick and hard. Then you can choose a more suitable instead of it. If your unit needs not pure gasoline, but its mixture with engine oil, strictly observe the proportions indicated in the operating instructions. There is one little thing: the recommended ratio is 1: 25 (for all grades of oil) or 1: 50 (for “native” oils). Try first the first ratio. If, with such a recipe, oil flow appears on the motor, and a strong carbon fiber forms on the candle, reduce the fraction of the oil in half. This usually contributes to the disappearance of traces and a decrease in the number of soil. To clean the electrodes of the candles from combustion products, you can use fine.grained “emery”

First wipe them with a dry rag, and then carefully clean it with sandpaper. If the space between the device body and the insulator is also clogged, the usual straightened office paper clip will help clean it. To do this, soak the candle for a short time in diesel fuel, and after scrape the pollution

If the clog is small, one procedure is enough. With strong pollution, sometimes you have to repeat it several times. After complete cleaning, the candle must be wiped dry from the remains of diesel fuel, and then can be used as intended. Keep in mind that the lawn mower (gasoline, electric or battery) requires a little more care than domestic. In particular, many persistently recommend the adjustment of the carburetor of a two.stroke engine to professionals, especially if your purchase has not expired the warranty period of service. And finally, another advice: follow all the recommendations of the manufacturer for the operation and maintenance of the device. So you extend its trouble.free functioning.

To do this, soak the candle for a short time in diesel fuel, and after scrape the pollution. If the clog is small, one procedure is enough. With strong pollution, sometimes you have to repeat it several times. After complete cleaning, the candle must be wiped dry from the remains of diesel fuel, and then can be used as intended. Keep in mind that the lawn mower (gasoline, electric or battery) requires a little more care than domestic. In particular, many persistently recommend the adjustment of the carburetor of a two.stroke engine to professionals, especially if your purchase has not expired the warranty period of service. And finally, another advice: follow all the recommendations of the manufacturer for the operation and maintenance of the device. So you extend its trouble.free functioning.

What to do if the gasoline trimmer for the grass does not gain momentum, you will learn later.

Rules for the operation and storage of a lawn mower

In order for the lawn mower to start well and continue to provide it with good storage and operation conditions:

• During operation, carefully monitor the cooling system, carefully and in time, clean the channels in the case, as well as the ribs of the starter;
• If necessary, use solvents, kerosene and other detergents for cleaning;
• Do not clean the “hot” tool. let it cool;
• Stactly comply with the requirements of the instructions for the operating mode, otherwise you can overheat the engine;
• If you do not plan to use the lawn mower in the next month, the fuel mixture from it needs to be drained, t. to. Over time, it breaks up into heavy fractions, which will definitely clog the channels of the carburetor;
• After draining the fuel, let the trimmer work at idle until it stalls, this will help to completely remove the rest of the working mixture.

Before winter storage, take the following steps:

• completely disassemble the braid, rinse and clean all the details you can;
• Inspect the details for damage, if necessary, eliminate distortions, impulses, bent and any other malfunctions;
• Pour a sufficient amount of oil into the gearbox and clean the air filter;
• You can partially disassemble the motor, rinse, blow and smear all the moving parts;
• In order to lubricate the piston, you need to unscrew the candle, raise the piston with the outlet to the extreme dead point, pour a little oil into the candle hole and scroll the crankshaft a couple of times;
• If you store the lawn mower not in the house, wrap the engine with an oiled rag.

Remember, careful compliance with the rules will allow you to forget that the lawn mower is bad for several seasons.

The lawn mower is not started, the spark is gone

The loss of the spark entails a check of contacts and the correctness of the clearance between them, conducting the wire to the candle and the candle itself. A method of checking the spark. to unscrew the candle, connect the wire to it, attach the candle sideways to the casing of the engine and pull the lawn.mower as if starting the starter several times, while you need to look at the corner and contact of the candle, the spark should run between them. If there is no sparks, take a new candle to do the same procedure, if the spark is not traced, the problem in the wire or contacts means it, it is better to replace them.

When pressing gas

In cases where the chainsaw stalls when you press the gas, you should check the silencer and the fuel filter. A possible cause of problem is a violation of the tightness of the fuel hoses. In some cases, the addition of revolutions helps.

Sometimes checking all the details does not give a result, the tool is suffocating, zooiling when gas is added. If the device stalls when a person presses gas, it is possible to supply fuel in insufficient amount for normal operation. This phenomenon occurs due to clogging of the carburetor or filter.

Damage can occur due to clogging with air filter dust. When you give gas, the device stops working. Do not eliminate the problem yourself, since each model has individual characteristics.

Calling may cause failure or lack of lubrication on the chain of the chainsaw. If the circuit is dry, the channels should be cleaned through which the oil is supplied to the device tire. If the oil proceeds, the presence of cracks, defects on the pipes is noted, you need to treat them with sealant.

The lawn mower is not started after winter

In such cases, it is necessary to conduct maintenance of the unit. Remove the fuel system, including filters (air, fuel), disassemble the carburetor, clean each node, rinse. Pour the filters with air

Pay attention to the quality and octane fuel number

It must be taken into account that the products of such well.known companies as Stihl, Husgvarna and other brands will not work on a cheap with a small octane number of gasoline. For them, suitable fuel from the AI ​​brand. 92 and higher with car gas stations and that, with well.proven ones, since gas stations are also bad gasoline. On the use of highly octane and high.quality gasoline, it will depend on how long the lawn mower will be used and how much it will last.

One more fact must be taken into account that with the long storage of diluted fuel mixture, it falls working qualities, which also leads to the consequences in which the lawn mower will not start. Therefore, it should be diluted with portions, that is, the amount of a mixture that is produced at a time. The operating instructions clearly describe and are given clarifications on the proportion of mixing gasoline and oil. Straighten compliance with the correct proportions will at least save you from several questions, why the lawn mower will not start and what to do in such cases.