Trimmer Huter what a fishing line is needed. Conclusions about choosing the best fishing line

Table of Contents:

How to wind a trimmer line on a trimmer Huter. Antirun.Ru

It should be slightly said about the strengths of the gasoline trimmers of the aforementioned manufacturer. The main ones can be called the subsequent:

  • The presence of a two.Stroke engine with a power of more than three horsepower, having air cooling and electrical firing;
  • A tank made of translucent plastic, which allows you to know exactly how many fuel was spent during operation;
  • The opportunity for a person to work is comfortable-this is obtained due to the presence of an ergonomic handle according to the type of bicycle and a special mechanism of extinguishing various kinds of vibrations;
  • Here, a high.Quality cutting headset is used in the form of a cutting knife and trimmer line of the highest strength;
  • A wide capture of 25.5 cm is also used here, which makes it possible to perfectly and rapidly mow grass, shoots and other greens;
  • A protective casing that protects a person from the hit of mowed grass, pebbles and various garbage;
  • Shoulder belt, which allows the operator to work for a long time and not feel lethargy;
  • Simplicity of maintenance and work. The mechanism of work and the device of models from Huter are very ordinary, which will allow simply to understand their introduction even to a little.Known person;
  • Reliability-such a gasoline trimmer can work for a long period of time without stopping, with all this it does not heat up due to the features of the air cooling system;
  • The possibility of unhindered movement around the site. Taking into account that gasoline trimmers, unlike electronic ones, are completely independent of the presence of a socket, which guarantees a person freedom of movement.

At the same time, there are a number of shortcomings that cannot be mentioned, but specifically: specifically:

  • Noise during work. Gasoline trimmers not only from Huter, and in general, they vibrate very much and publish great noise, which makes uncomfortable working conditions;
  • Contamination of nature. Models working on combustible, during operation form various kinds of exhaust gases, which harm the environment;
  • The highest price-trimmers of the described type have the highest price due to the fact that they own the highest performance and good technical features.

Types of section

There are a lot of views of the trimmer line, you can not pay attention to the color of attention-as such general standards “color-characteristics” do not. An important factor is the type of cross section of the string, it is chosen depending on the type of grass.

  • Circle. Universal trimmer line. Smooth when mowing is characterized by an increased noise level, twisted, on the contrary, mows quieter, but is consumed faster (like any type of twisted trimmer line).
  • Square or polygon. Such a trimmer line is more effective than round. Sharp corners cut the stems faster and better.
  • Asterisk, ribbed or twisted square. Has maximum efficiency and haircut speed.

Manual or mechanical coils their purpose and application

The first trimmers were produced with manual types of coils that have a primitive design. They consist of a plastic or metal disk in which there are holes for fixing the trimmer line. The holes have the corresponding size, which allows the use of a cord (trimmer line) of a certain diameter. However, this is not the only drawback of equipment, since another minus is the need for frequent trimmer line refueling. Below is a variant of the simplest coil with a trimmer line for a trimmer.

Following the simplest coils, mechanical head heads appeared, inside which a bob is installed with a fishing rod. Such devices are excluded deficiency of the fast consumption of the cord, however, to serve a new trimmer line, you should interrupt the work on the injection of grass. To supply the cord, the head is equipped with a manual regulator, through which the trimmer line stretches. Today, the manual type models are rarely used, which is associated with their great drawback. The need to interrupt the work and drown out the engine in order to lengthen the cord.

What materials are used for the production of trimmer line and how it affects their reliability

For the manufacture of a trimmer trimmer line, nylon is used, which is based on polypropylene with polyamide. A distinctive feature of nylon is its following advantages:

  • Strength subject to storage conditions. Prolonged storage of material in the sun or at low temperatures cannot be allowed
  • Lightness, which allows you to develop high speed by inertia of rotation of the head
  • Wear resistance. The material is resistant to wear, and the cord damage occurs only in a collision with solid obstacles
  • Low cost is convenient, since the material is consumable, and the constant use of a new trimmer line is required

It is interesting! The nylon trimmer line when driving grass is torn into pieces that remain in mowed grass. These pieces are harmful to animals, so mowing grass with trimmer line for hay harvesting is not recommended.

Sometimes a cheaper polyethylene is added to the material, which reduces the reliability of cutting equipment. The polyethylene cord is we wear out faster, so the experience proves that it is more profitable to buy a trimmer line made of natural nylon (it is more expensive) than save and purchase a plastic cord.

Fishing lines with a thickness of 2.6-3.3 mm consist of nylon even of graphite or steel rods-a two-component cord. The presence of rods increases not only the efficiency of injection of grass, but also reduces the Rapid wear of the trimmer line. As a result, it turns out that a string with a large section lasts longer than a thin trimmer line. There are also cords with the addition of metal particles to the composition. These additives are also designed to increase the efficiency of grass injection, and increase the strength and wear.Resistant parameters of the material.

It is interesting! When choosing a trimmer line for your trimmer, you need to pay attention to the head or coil. These details indicate the parameters of the cross section of the cord allowed for use.

How to store a trimmer line or increase the service life

Many give advice on how to choose a trimmer line for a trimmer, but few give information about how to store it. Incorrect storage leads to Rapid wear of the trimmer line when mowing grass. After buying a 15-foot coil, only a few ask how to store a trimmer trimmer line. When buying a coil of 250-500 meters, it is very important to understand storage conditions.

What will happen if the nylon trimmer line for the trimmer is stored incorrectly? The consequences are as follows:

  • Loss of properties, therefore, from high.Strength material, the equipment becomes fragile and quickly wear out
  • The efficiency of work is reduced
  • Accelerated wear leads to the need to buy and re.Lay more trimmer line in a trimmer

The loss of the initial characteristics of the line is a real nuisance, so let’s find out what can be done to extend the service life of your line during storage. Nylon material is most susceptible to ultraviolet radiation. The longer the line is stored in the open sun, the faster it loses its technical properties. Below are instructions for extending the service life of trimmer line for a trimmer:

  • At the end of the season, after a long break, wrap the cord into polyethylene, having previously soaked it with grease (glycerin). The trimmer line tightly wrapped and saturated with fat should be stored in a dark place at a temperature of 5 to 20 degrees (best in the refrigerator).
  • Do not store the line on radiators or heaters, since excessive heating leads to a deterioration in the technical properties.
  • To avoid the full effect of light on the line, it is better to wrap it in black, and not in transparent plastic. Instead of a package, you can use special plastic sealed containers

Trimmer line

When the season comes, remove the roll, wrap the required amount of material, wipe the lubricant and load it into the trimmer drum.

Rescuing a screech owl tangled in fishing line, New Jersey. 09/06/2015

Which form is better

Also, do not forget about the shape of the trimmer line. It affects the cost and efficiency of work. So, let’s talk about the main forms of section:

  • Circle is the most common, easy to manufacture and therefore cheap trimmer line. Perfectly suited to mow thin, young grass. However, when working, it is very noisy that it will hardly like the user of the trimmer and others. As a result, manufacturers released a round trimmer line with a twisted cross.Section. It is a little more expensive, mows tangibly quieter, but it is consumed faster.
  • A polygon or square is characterized by higher efficiency compared to round. Thanks to sharp corners, even rather thick grass will be cut off instantly. A square trimmer line costs a little more than round, thus, thus, a successful compromise between value, comfort and efficiency.
  • A twisted square or asterisk boasts the highest speed of mowing, and even dried or hard grass will not become an obstacle. Sharp edges will easily deal with it. Noise level is relatively low, but the cost of such a trimmer line is the highest. This scares away some potential buyers. In fact, the “Asterisk” fully justifies its cost when mowing hard grass, saving a lot of time to the user.

In addition, you can see a trimmer line of different sections on sale, but with special zazubins. They increase the efficiency of work, but at the same time they increase the cost of the material.

As you can see, it is quite easy to deal with the cross section. Remembering these simple rules, you will probably easily decide which trimmer line on a trimmer will be the best choice for you.

How to choose a trimmer line for a trimmer?

It is almost impossible to imagine the care of a garden plot or a adjacent territory without such a useful, saving tool and the time of the tool as an electric trimmer or benzocos, for which you will need such cutting consumables as trimmer line (or as it is also called. Cord, cord cord, mowing string, vein).

Today, various types of trimmer line for trimmer from different manufacturers are presented on the market. What are their differences, which trimmer line is better for a trimmer, how to choose the right trimmer line for a trimmer. We will talk about this with you further.

The choice of trimmer line for a trimmer is influenced by such parameters as the composition of the material, the thickness and shape of the section. Let’s figure out what they are and what are their differences.

See also  Carburetor Trimmer Setting

Famous manufacturers of garden equipment and inventory, as a rule, produce a trimmer vein from nylon with special additives, which provides the cord with flexibility, high wear resistance, and the strength of the gap. In addition, the material is easily stretched, perfectly tolerates the temperature difference and significant loads.

The standard trimmer trimmer line will perfectly cope with the haircut of the lawn, herbs in the garden, but if you need to dig up a particularly hard grass (hogweed, burdocks, reeds). It is better to use a reinforced trimmer line. But it should be noted that although the trimmer trimmer line with a metal core is more reliable, durable and wear-resistant than a nylon monoles, but its installation in an electric and benzotrimer with up to 1.5 kW is not recommended.

In the shape of the cross section, the cord cord happens:

Round trimmer line for trimmer It is considered universal, as it is suitable for mowing all types of vegetation. It fits well into the coil of benzos, it is economically consumed and has an extensive choice of sizes. A significant drawback of the round trimmer line is an increased noise when cleaning grass, therefore, to protect the hearing organs, you should get special headphones or beurushas.

Figure line for a trimmer (square or asterisk) Due to the presence of acute faces, it has higher cutting properties, makes less noise, easily copes with fresh, overripe and rough grass, but is less durable than a round trimmer vein, more often abrasions and breaks.

Twisted trimmer line for a trimmer, Having high aerodynamic characteristics, creates 50% less noise than a round cross.Sectional cord, which is appreciated with prolonged work. This type of cord cord is perfect for cutting thin vegetation.

Standardly braid cord is made with a diameter of 1.6 mm, 2 mm, 2.4 mm, 2.7 mm, 3 mm, 3.3 mm.

It is used mainly in electric trimmers and batteries with a capacity of up to 0.7 kW.

It is used in the equipment of electrimmers with a capacity of more than 1 kW and benzocos with a capacity of up to 0.9 kW.

Designed for medium.Power motorcycle. Up to 1.4 kW. The most popular veins of this diameter of the twisted section or round.

Designed to equip semi.Professional motorcycle.

Used in powerful professional motorcycles.

Used only on professional models of electric and gasoline trimmers of high power. Such a trimmer line has a round section and is sold in large bays.

A trimmer line for a trimmer should be ideally approached by a coil in parameters. Too small option is unacceptable for use, as it provoke confusion inside the coil and will also lead to a breakdown of the working unit or the entire trimmer. At the same time, if the cord is too thick than recommended by the manufacturer, it will increase the load on the engine, and will also not allow the trimmer to develop the required speed. Therefore, the choice of the diameter of the trimmer vein should be approached as responsibly as possible.

The trimmer line can be of different colors, but this characteristic does not affect the work of garden technology. Unless the dirt is less visible on the black trimmer line, and the bright equipment is clearly visible in the grass.

trimmer, huter, fishing, line, needed, choosing

So we have figured out which fishing line is better to use for a trimmer and what main parameters affect the choice of trimmer line trimmer. It remains only to find out where you can order accessories for benzo and motorcycle?

You can buy a trimmer line for a trimmer inexpensively in the AGROVINN online store. We offer you to purchase a spit cord of the Polish manufacturer Bradas, in the assortment of which there is a trimmer trimmer line of various diameters, with a different cross section, with a metal core and without winding from 15 to 481 meters.

By calling our managers by the phone indicated in the contacts, you can not only find out the cost of the trimmer line and order a mowing string, but also consult and find out which trimmer line is better to put on your trimmer.

You can pick up the trimmer line to the trimmer from our own from the Agrovinn warehouse in g. Vinnitsa. If you do not live in Vinnitsa, we will be able to deliver to you the spare parts for the trimmer with the New Mail services or “Intime” to Kyiv, Odessa, Nikolaev, the amount, Kherson, Kirovograd, Cherkasy, Poltava, Zaporozhye, Kharkov, Dnepropetrovsk, Ternopol, Khmelnitsky, Khmelnitsky, Khmelnitsky, Khmelnitsky, Khmelnitsky Zhytomyr, Chernivtsi, Lviv, Uzhgorod, Ivano-Frankivsk, Lutsk or to any other settlement of Ukraine.

Therefore, if you need a good trimmer line in a trimmer for adequate value and with delivery in Ukraine. Contact Agrovinn!

The main parameters of the trimmer trimmer line

Fishing lines can be classified according to the following parameters:

The thickness of the thread

You can find out about it by reading the operational characteristics of the trimmer or focusing on sizes and inscriptions on a universal bobbin. Typically, threads with a diameter of 1.2-4 mm are used for trimmers. True, for each device you will have to select a trimmer line of a certain diameter.

trimmer, huter, fishing, line, needed, choosing

The thread for the trimmer, thinner than the required, the engine will not disable immediately, although it will significantly increase its wear. If you use the thread thicker than necessary, the resistance of rotation will increase, the engine will operate more intensely, overheat and, as a result, will break. True, a lot depends on the engine itself.

You can find out the approximate diameter of the trimmer line for the type of engine. If the trimmer works from electricity or battery and its power is 1 kW, you need a cutting thread with a diameter of 2 mm, and if its power is less than 500 W, you use a trimmer line not more than 1.6 mm.

For a gasoline trimmer, the trimmer line is chosen with a certain diameter. 2.4. 3 mm. The choice of such a thick trimmer line is associated with the features of gasoline units. They are more powerful and productive than their electrical counterparts. You can operate a thick trimmer line for a long time, in addition, it will easily overcome a long.Term dry.

The shape of the section

The most commonly selected trimmer line for electric ships with a round section. It is inexpensive and the most popular, sprinkles fresh grass well. Its main disadvantage is in the published level of noise, which is heard during the work of the trimmer. The noise of the trimmer line is close to the engine hum. For the best noise use, manufacturers offer to use a spiral trimmer line.

trimmer, huter, fishing, line, needed, choosing

Today also produces a trimmer line for a trimmer. Of other forms, quite often rectangular and starry. Particularly productive fishing lines with zazubins and sharp edges are. Such faces cut the grass more evenly.

There are also options for trimmer line with notch and dents. They can download large weeds. The noise level published by such a trimmer line is low, and due to the increased properties of aerodynamics, the trimmer is given additional power. Such a cutting element is installed on powerful trimmers, which are planned to carry out work in overgrown, neglected areas.

To work with a trimmer line of this type, special heads are installed on the motorcycle. The trimmer line is wound on them. She copes with herbs of any kind (especially weeds) and shrubs. But its cost is quite high. The consumption of such a trimmer line is also high, since when serving from the coil, difficulties can arise with its extraction. It is usually used with disks in which it is inserted in small segments.

There is also a two.Component twisted trimmer trimmer line. Its purpose is a high.Quality mowing of dry. It is distinguished by a round section, resistance to ruptures and increased strength. It comes with the core produced from other material. Twisted trimmer line is suitable only for gasoline trimmers. She is able to cope even with small shrubs. Its main drawback is the high cost. For daily work, purchasing a twisted trimmer line is quite expensive.

The composition of the trimmer line

It is the composition that determines the life of the trimmer line. Often it is made of nylon. It slowly wears out and increases the efficiency of performance at high temperatures and high loads. The material retains its working properties for a long time, low temperatures do not affect it, as well as prolonged work.

The trimmer line of the coaxial group for trimmers is considered one of the strongest. It has a dense core, and therefore wears out gradually. Such a trimmer line is difficult to cut with a knife and when working creates little noise. There is also a trimmer line now, which includes intersperses of aluminum.

The best manufacturers of trimmer forests

For the effective operation of the lawn mowers, you need to pay off high.Quality threads of trusted brands. There are many manufacturers whose fishing lines are popular at the expense of their many advantages:

  • “Oregon”. A world manufacturer of various equipment for garden equipment. Fishing lines are produced for both household and professional use. A large range of threads for high.Quality lawn mowers is produced.
  • “Husqvarna” is a well.Known brand of garden equipment with extensive experience that produces all types of forests for lawn mowers.Threads have a special classification by color solution depending on the diameter. The manufacturer is also patented by the sewn.Out processing of threads, which makes them stronger and more elastic.
  • Champion is a relatively young manufacturer who has established itself in the market thanks to high-quality garden equipment. Produces fishing lines for a trimmer of all types with high wear resistance and strength. There is a yellow and red series of threads with different sections.
  • Dolmar is a popular manufacturer who has been producing various garden products for more than half a century. The threads for the trimmer are distinguished by high technical characteristics. You can purchase fishing lines of this company both for working in well.Groomed lawn areas, and for cutting launched grass.

Champion trimmer trimmer line

A properly selected trimmer line for a trimmer will allow you to cut not only soft grass, but also hard, dry.

Learning to properly wind the trimmer line on the coil of the trimmer and benzo.Coat instructions for installation

Owners of private houses know how necessary such a type of tool as a trimmer is. It can be gasoline and electric, and they differ in the design of power units. For injection of grass in areas where there are stones, trees and other obstructing objects, trimmer line is used as a cutting device. This consumable in the process of use wears out, therefore, how to wind the coil of the trimmer, we will consider in detail in the material.

Fishing lines is called consumable, which consists of nylon, and serves as a cutting device. Through this equipment, the grass grows, which is ensured due to rotation of the instrument head with a high frequency. This material has a different thickness, which depends on its use on the corresponding tools of low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers with motorcycles (from 2.4 to 3. 2 mm).

Fishing LINE Types 101 | When to Use Mono, Fluoro, or Braid

The more powerful the tool, the accordingly there should be a cutting equipment. This affects not only the quality of the injection of grass, but also on the life of the material. If you ask the question of how to wind a trimmer coil, then it’s time to change the reload of the tool. With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the step.By.Step instructions for replacing the trimmer line in the coil of the trimmer.

Characteristics of a trimmer trimmer line

To understand what trimmer line for a trimmer is needed for your mowing model, it is enough to determine its main parameters: the thickness of the thread, the shape of the section, the composition. Consider all components in more detail.

See also  How to Mount a Disc on a Huter Trimmer

Free thickness (cord)

You can find out the desired thickness by looking into the characteristics of the trimmer or by reading the inscriptions on a universal bobbin. Most often, cords with a diameter of 1.2 to 4 mm are used. Over, for each individual model, there is its own diameter for a trimmer. The fact is that if the thread is thinner than the necessary, then you will increase the engine wear, due to the increased number of speed revolutions. If, on the contrary, it will be too thick, then the resistance to rotation will increase, and the engine will begin to overheat and ultimately fail. To determine the exact diameter of the thread, it is best to navigate by type of trimmer engine. Thus, it turns out the following:

  • For an electric trimmer with a lower location of a “engine” with a power of less than 500 W, a thread of 1.3 mm thick will be needed. If you have not found one, then you can use a thicker trimmer line by 1.6 mm, but no more.
  • For an electric trimmer with an upper engine of about 1 kW engine, select a thread with a diameter of 2 mm.

It doesn’t matter what kind of electric trimmer the type of shaft, bent or straight (allows you to install knives).

Advice! If the tool is initially installed in the tool with a diameter of 1.6 mm, then you can put a thread for 2 mm, this will not affect the engine operation.

If we are talking about a gasoline model, then in this situation it is necessary to determine which mowing is the shaft. For bent, filaments are most often used 2 mm thick. But a trimmer line for a 3 mm or 2.4-2.5 trimmer is installed on a tool with a straight shaft. The thicker trimmer line is usually placed on more powerful tools (from 1.3 kW).

If we talk about which trimmer line is better coping with young grass or perennial dry, then you can conditionally divide the cords into the following categories:

  • Fields from 1.2 to 1.6 mm. This is the thinnest thread that is used to adjust the lawn.
  • 2. 2.4 will allow you to cut off both young grass and more rigid. Suitable for periodic use.
  • Thread from 3 to 3.2 mm will allow you to mow grass and thick stems of weeds or dryness if you rarely leave the country.

Less common, there is a trimmer line for a trimmer of 4 mm. This is due to the fact that rarely anyone has to deal with such serious thickets. However, if you are the owner of a powerful gasoline “mowing” and did not appear in the country for several years, then the trimmer line for 4 mm will be the best option.

The shape of the section

There is a large selection of a cord with a different section, depending on which the trimmer can mow this or that grass:

  • The cords with a round cross section are the most popular, while such fishing lines are cheaper than the rest, from 68 rubles (12 m). They mow fresh grass well, but they cope worse with ducklings and shrubs. The lack of such a trimmer line lies in a fairly strong noise that resembles a rumble from a running engine of a machine.
  • The spiral (twisted) cord is noisy, but does not differ in high strength. Therefore, such a trimmer line is suitable only for thin young grass, for which you constantly care. There is such a trimmer line from 100 rubles.
  • Square, rectangular or star trimmer line allows you to mow a low noise lawn evenly. True, such products also cannot boast of strength. Such a thread will cost about 147 rubles per 12 meters.
  • The jagged cord with sharp edges is used for large weeds in neglected areas. At the same time, the trimmer line will not publish much noise, and thanks to the increased aerodynamic properties, the mower will be given additional power. Such a thread worth a cost of 200 rubles is suitable for a powerful trimmer. The jagged cord is considered durable and reliable.
  • A two.Component trimmer trimmer line with an internal core with a round section is considered the most durable of all. Thanks to the core made of other material, the cord can mow even small shrubs. True, such a trimmer line is suitable only for gasoline trimmers. Due to the high cost (from 250 rubles) of such a cord, it is impractical to use it daily.

The composition of the trimmer line

It directly depends on the composition of the fishing line how much it will last. Most often, threads are made of nylon. This material wears more slowly and is characterized by high performance in high temperature conditions and high loads. The duration of work also does not affect the properties of nylon.

Coaxial fishing lines are considered the strongest. They can be distinguished by a dense core, thanks to which such cords wear out longer than nylon. It is difficult to cut such a trimmer line with a knife, and during the mowing process it makes a minimum noise.

The most expensive fishing line is the one in which aluminum goes, or rather, its interspersed. Such a cord appeared on the market relatively recently, but already with confidence we can say that it is the most durable.

Types of cords

Of course, the option to come and show the fishing line to the seller is reliable, but he is not entirely correct. And this is explained by the fact that the choice of trimmer line depends not only on the trimmer head, which is used in the design, but also on the power of the unit.

The following varieties of forests are distinguished:

  • Cords with a cross section up to 1.6 millimeters. They are used mainly in electric trimmers, where engine power does not exceed 500 watts. The tools do perfectly with the trim of lawn young grass in small areas. You can buy a trimmer line for a trimmer on the website of the online store.
  • Cords with a cross section from 2 to 2.4 millimeters. They can be found in gasoline or electric trimmers, in which the power indicator lies in the range from 500 to 1,000 watts. Basically, such a technique is in demand when cutting thin or thick grass, to eliminate the site from weeds. If you set the trimmer line with a cross section of 1.6 mm in such units, it will quickly become unusable, and it will need to be changed.
  • Cords with a cross section of 2.4-3.3 millimeters. Used in gasoline trimmers in which the power indicator exceeds 1,000 watts. Such a trimmer line copes well as with grass, so with thick and dried stems, allowing you to trim shrubs and trees.
  • Manufacturers also produce a trimmer line with a diameter of more than 3.3 millimeters, but it is used very rarely. It is better to buy it for a high.Power trimmer.

What is important to know when working with trimmer line?

In order for the tool to serve you for a long time, you need to know some features of its device, storage and maintenance:

  • The head of the trimmer during operation should be located parallel to the ground so that the trimmer line does not hurt the ground and stones. It is advisable not to touch hard objects, borders, fences.
  • Electric trimmers are most sensitive to damp, so you can’t work in rain and raw weather.
  • After the end of the work, you need to carefully clean all the parts of the mechanism of dirt, grass, wipe all the wires and trimmer line so that everything functions well at the next time.

TOP-15 Rating of the best forests for trimmer 2021-2022

Place Name Price
The best fishing lines for a trimmer for price/quality for 2021-2022
one Bosch F016800431 3.5 mm Find out the price
2 DDE Classic Line 2 mm 63 m Find out the price
3 Husqvarna T25 M10 (5784461-01) Find out the price
The best fishing lines for a trimmer 2 mm
one DDE Hard Line Circle 2 mm 15 m Find out the price
2 Elitech 0809.002100 2 mm 15 m Find out the price
3 Husqvarna Whisper Twist 2 mm 112 m Find out the price
The best fishing lines for a trimmer 2.4 mm
one DDE Speed ​​Line 2.4 mm 116 m Find out the price
2 Huter S24 Star 2.4 mm 12 m Find out the price
3 DDE Classic Line 2.4 mm 44 m Find out the price
The best fishing lines for trimmer 3 mm
one Elitech 0809.006200 3 mm 12 m Find out the price
2 Huter S30 Star 3 mm 12 m Find out the price
3 DDE Hard Line 3 mm 120 m Find out the price
The best fishing lines with a core for a trimmer
one DDE Hard Line 2.4 mm 180 m Find out the price
2 Elitech 0809.006000 2 mm 15 m Find out the price
3 Sturm! GT3535-3.0-0M-10 3 mm 10 m Find out the price

When buying trimmer line for a trimmer, it is necessary to take into account the main features of a quality product.

  • The thickness of the thread. You will find the indicators of the desired thickness in the instructions for the device. Each trimmer model works with a trimmer line of a certain diameter. For an electrical device, you need a thread with a diameter of 2 mm, but for gasoline trimmer line you need to choose a thickness of 2.4-3 mm. Then the load on the consumer is distributed correctly and it will be convenient to work with the trimmer, without propelled grassy grass.
  • The shape of the section. Most often, users prefer trimmer line with a round section. It pleases with an affordable price and quickly copes with the bevel of fresh grass. However, devices working with a round trimmer line will make a loud noise. If you want to reduce the noise level, then you can try a fishing line with a square or rectangular cross.Section, however, it is a little more difficult to find them than with a round. If you have to work with dry.Resistant, it is better to give preference to the option with a twisted two.Component trimmer line, which is stronger and resistant to breaks, but due to this, its price is higher.
  • The composition of the trimmer line. The composition determines the service life. Most models are made of nylon. Such a trimmer line gradually wear out, but effective at large loads. Need a strong trimmer line for working with thick weed stems? Choose a coaxial trimmer line, it is considered one of the most durable, it is difficult to cut even with a sharp knife, and the noise level during the operation of the trimmer is significantly reduced. Such a trimmer line is used by communal services or owners of large sections with a large amount of vegetation.
  • Manufacturer. We will talk about the best just below, but experts recommend using “native” fishing lines for the trimmer, produced by the same brand as the device itself.

Characteristics of a trimmer trimmer line

To understand what trimmer line for a trimmer is needed for your mowing model, it is enough to determine its main parameters: the thickness of the thread, the shape of the section, the composition. Consider all components in more detail.

Date of publication: January 25, 2016. Category: Articles.

A beautiful lawn is the face of a summer cottage, so most gardeners prefer to sow special silky grass on their land, which not only pleases the eye, but also displaces annoying weeds. In addition to feeding and watering, lawn grass needs care, respectively, it must be periodically mowed. For these purposes, you can choose an electric trimmer Or a lawn mower. Many prefer trimmer. The reel with a trimmer line is the main tool for this device, it allows you to quickly cut off an even layer overgrown grass. In addition, using a trimmer, you can equalize the lawn in the most inaccessible places: in areas along the tracks and fence, around and bushes, trees or well.

Which line to choose for a trimmer and motorcycles

Regardless of whether you use a regular tool equipped only with trimmer line, or electric trimmer With a knife and trimmer line, sooner or later you will have to change some elements of such a device. Unfortunately, by this moment, the instructions from the portable lawn mower, where all the necessary requirements are indicated, is already lost and many are faced with the question of buying a “correct” trimmer line.

See also  Trimmer Shaft Lubrication

Free thickness (cord)

You can find out the desired thickness by looking into the characteristics of the trimmer or by reading the inscriptions on a universal bobbin. Most often, cords with a diameter of 1.2 to 4 mm are used. Over, for each individual model, there is its own diameter for a trimmer. The fact is that if the thread is thinner than the necessary, then you will increase the engine wear, due to the increased number of speed revolutions. If, on the contrary, it will be too thick, then the resistance to rotation will increase, and the engine will begin to overheat and ultimately fail. To determine the exact diameter of the thread, it is best to navigate by type of trimmer engine. Thus, it turns out the following:

  • For an electric trimmer with a lower location of a “engine” with a power of less than 500 W, a thread of 1.3 mm thick will be needed. If you have not found one, then you can use a thicker trimmer line by 1.6 mm, but no more.
  • For an electric trimmer with an upper engine of about 1 kW engine, select a thread with a diameter of 2 mm.

It doesn’t matter what kind of electric trimmer the type of shaft, bent or straight (allows you to install knives).

Advice! If the tool is initially installed in the tool with a diameter of 1.6 mm, then you can put a thread for 2 mm, this will not affect the engine operation.

If we are talking about a gasoline model, then in this situation it is necessary to determine which mowing is the shaft. For bent, filaments are most often used 2 mm thick. But a trimmer line for a 3 mm or 2.4-2.5 trimmer is installed on a tool with a straight shaft. The thicker trimmer line is usually placed on more powerful tools (from 1.3 kW).

If we talk about which trimmer line is better coping with young grass or perennial dry, then you can conditionally divide the cords into the following categories:

  • Fields from 1.2 to 1.6 mm. This is the thinnest thread that is used to adjust the lawn.
  • 2. 2.4 will allow you to cut off both young grass and more rigid. Suitable for periodic use.
  • Thread from 3 to 3.2 mm will allow you to mow grass and thick stems of weeds or dryness if you rarely leave the country.

Choose a trimmer line for a trimmer of gasoline (motorcycles | Benzokos): 1.6, 2, 3 mm. Round, star, square

Less common, there is a fishing line for a trimmer of 4 mm. This is due to the fact that rarely anyone has to deal with such serious thickets. However, if you are the owner of a powerful gasoline “mowing” and did not appear in the country for several years, then the trimmer line for 4 mm will be the best option.

Five things that will make your trimmer trimmer line better, trimmer line and reel

So that your trimmer trimmer line works in the best way in the next season, we list five things to maintain high performance of the trimmer trimmer line for your reference.The trimmer line is known as the trimmer line, the eating line of weeds, the line, the line for removing weeds. Time. Money, and when commercial landscape designers spend more and more time on setting up, replacing or repairing a trimmer trimmer line, this begins to cost money! One of the simplest ways to maintain the working capacity of the trimmer begins with the trimmer line itself.

Proper storage of a trimmer trimmer line

Do not store a trimmer trimmer line under direct sunlight. If the reel of the trimmer line is stored under direct sunlight, there is a risk of damage to the trimmer trimmer line in UV rays, which will make it brittle.The industrial class trimmer line will withstand stones, weeds and other obstacles, but the trimmer line for the trimmer, which fades in the sun, will require more time and attention. The trimmer and especially the head of the trimmer are subjected to unnecessary wear, when the user requires more trimmer line with shock feed.

The professional trick in servicing the trimmer is to remove the trimmer trimmer line and leave it to soak in fresh water during the winter season. Thus, he will retain his flexibility, withstand a large load and last longer Trammer trimmer line made of nylon and can be a mixture of polymers to ensure maximum flexibility and the necessary rigidity. A strange feature of nylon is its affinity to water. Some polymers can absorb up to 12% of their weight. Water acts as a plasticizer or softener and, thus, reduces the likelihood of destruction or cracking of the cord when used and actually gives the cord some stretching. To some extent, the physical properties of the polymer in the line can be restored by soaking, but over time it will not work.The old line cannot really be returned to its original state. The same applies to a trimmer line from mononity.

|| choose the best size of trimmer line || পারফেক্ট লাইন সাইজ কত? || best trimmer line diameter ||

As a rule, the thicker the trimmer line, the longer you will have to impregnate it, and 24 hours are actually not enough. Store it in a polyethylene bag with a wet cloth is a good idea. Previously, the trimmer line quickly dried, became fragile and easily torn. Soaking was an old trick many years ago, which worked pretty well. The modern trimmer line is not so much subject to drying.

The correct winding of the head of the trimmer prevents jamming, tears and uneven distribution of trimmer line.If the trimmer line is wound too tight or even too free, one side of the trimmer trimmer line will stuck in the head of the trimmer. The use of the right technique will be more effective, since the loading of a trimmer trimmer line takes much less time. When trying to fix with the help of shock supply, the trimmer line is distributed only in one direction, which leads to an unbalanced trimmer that does not work. Wrap the trimmer trimmer line on the head as directly as possible. Preservation of the trimmer line without excessive tightening will provide uniform feeding of a trimmer trimmer line.

Proper winding of trimmer line for a trimmer is a skill that requires some practice and dexterity to do everything right. It is not easy to do this right, so give yourself some time to find out how to do it best. The trimmer head looks a little complicated in disassembled form, but by dismantling and collecting it several times, you will see how this should be done so that everything works correctly.

Avoid the work of the trimmer for full gas

The head of the trimmer, rotating at full speed, emits quite a lot of heat.The trimmer line in the head of the trimmer will melt and connect with itself in the process called trimmer line. After the trimmer line melted, the head of the trimmer has to be disassembled for a laborious repair.

Set the trimmer thrimmer’s thrummer shutter to cut off the plants that you cut. If you run the trimmer faster, the trimmer line will not last so long, and you will have to cope with a lot of noise and vibration, without getting any benefit. For most pruning works, you do not need full gas; You may need to install a full gas to clean the brush.

Get more power and a cleaner cut when cutting closer to the end of the trimmer line. In other words, cut as far as possible from the center of the head of the trimmer. A more effective haircut means a smaller wear of the trimmer and allows you to use the trimmer line as it was conceived.

Cut high grass from top to bottom

When cutting grass or weeds with a height of more than 8 inches, use short blows to first cut off the tops of the plants, and then move down to the base, instead of trying to cut the entire plant in one pass.

Use a blade for heavy pruning

Replace the commercial trimmer line of a trimmer with a metal blade for weeds when cutting thick grass, more heavy weeds and lignified shrubs with a diameter of up to 1/2 inch. To get the best results with a trimmer blade, keep it sharp and use full gas. Keep your legs firmly and at a convenient distance from each other so as not to lose balance if the cutting blade hit the object and bounces.

The choice of the type of trimmer trimmer line depends on personal preferences.Due to the variety of shapes and sizes, there are many options to meet the needs of any operator and/or work site. Another consideration when buying a trimmer trimmer line is its color. Green or darker lines are a popular choice, because scraps disappear in the grass, unlike brighter lines.

How to work with a trimmer line

Speasing the grass with a trimmer, it is important to avoid the contact of the trimmer line with stones, fence or wood. Contact leads to grinding the cord, reduces its service life. Whatever quality trimmer line, she still has a resource. Therefore, it is important to know how to correctly change the trimmer line on the trimmer.

First of all, it is necessary to extract the bobin from technology. The removal procedure is determined by the model:

  • If the drive is located below, then to remove the upper part of the coil, you must simultaneously press the button located on the sides.
  • For devices with a curved rod, hold the bobbin with your hand, and turn the lamb to the left free (counterclockwise).
  • At the unit with a straight handle, a groove is found from the bottom of the coil and set a screwdriver in it. Turning the body of the coil to the left, remove the bobbin.

After successful extraction, the bobin is disassembled in an even, free place from vegetation. You need to act carefully. Inside the coil is a spring that is easy to lose. As a result of the analysis, several parts are obtained: the casing, case and directly the wiper itself.

Trimmer line refueling on the trimmer occurs in accordance with the model of technology.

Coil with one hole under the trimmer line. A thread 2-5 m long is cut off from a skein. The end of the cord is turned into the groove of the coil and pressed with a finger, and the thread is wound in the direction of the reverse working rotation (indicated by the arrow on the case). The turns should fit tightly to each other. At the end, the body of the bobin is installed, in the hole of which the working end of the thread is displayed.

Winding is carried out opposite to working rotation in one or two grooves in accordance with the design of the spool. Когда нить станет подходить к концу, ее хвостики выводят сквозь 2 отверстия верхней части катушки.

There are coils with automatic winding of the cord. It is enough to correctly insert the end of the trimmer line, and the turns will be formed independently after acting a special mechanism.