What a pitch of carving on a grinder. Selffixed nut

What a pitch of carving on a grinder

Passed the exam in 2012, very hard prepared and did not write off. In the necessary subjects received: 86 in history, 80 in social studies and 72 in Russian. It was in Russian that I pierced, because usually with all test and trial exams I made no more than 4 mistakes, and I made as many as 8! As a result, I handed over 238 points. In my “secondary” school, it was the highest ball, and even with a margin, but when entering the university, it turned out to be far from the highest.

In general, I decided to enter the philosophical at UrFU (Yekaterinburg) and already went to the last budget place. But then one girl wrote to me in a personal with the question “Will I have time to submit documents?”. I answered her that would have time, and it all decided. She had 239 points and she took my place. So I didn’t have enough one score. In the third year, having taken up the mind, he still transferred to the budget place to the fourth year.

How to work as a grinder correctly

Ushm. One of the best.Selling tools. The secret of the popularity of the Bulgarians in practicality and versatility. However, you do not need to “flatter” the visible simplicity of its design. With non.Compliance with the rules of operation and safety precautions, even the Bulgarian can harm even the Bulgarian. An annoying mistakes are made even by experienced masters, who often risk without any reason. This also applies to beginners who do not read the user management.

What to do if you have lost an open key

Precisely, how to unscrew the disk on a grinder without a key? There are three ways:

  • Make a bracket from a bar of a suitable diameter (a nail is suitable). With such a device, you can loosen the flange with the help of hands. If the tightening is too strong, insert the lever into the bracket.
  • Use the gas key. Growing around the external radius of the threaded flange, just slide the nut, and then it will unscrew with your hands.
  • Still the thread with accurate blows on the tangent. To do this, you can take a core or punch, install it in a hole for an ore key, and with light beats of the hammer to turn the flange.

All manipulations for changing the nozzle are carried out after disconnecting the network cord.

What is the thread on the grinder. What is the thread on the grinder diameter

The main working properties of the grinder should be considered in subsequent directions: the transverse of the working disk, power of the electric motor, the speed of rotation and the weight of the tool. The last feature plays an important role to choose the right grinder and is located depending on the diameter of the disk, on which, when other working properties of the grinder depend. After all, it is clear that the disc is not just a disk for metal, on wood or concrete, how just during operation he will be subjected to friction force, which the electric motor and tools should overcome.

In order to nullify our client, potential cases of injury while working with a grinder, it is necessary that the factory properties indicated on the tool body exceed such designations applied to the disk type you have chosen. For simplicity of the concept, we take a very all.Fought metal disk with a 125 mm dialect and popularity of the Bosch company (angular grinding machine).

We study the capabilities of Ushm Bosch, which are indicated on the hull tag as it is also called in the technical passport: power 2000 W, the engine speed 6500 rpm, power from the 220 V network, is designed for disc 230 mm with a diameter of 230 mm, thread on spindle m 14. Now we take the usual cutting disk for metal with a diane of 125 mm where the permissible speeds of 12250 rpm are indicated, the dimensions of the disk and linear speed are 80 m/s.

Areas of the use of corner grinding machine

At first glance, this “application” may seem completely superfluous, as it has very limited functionality. But is it? Your attention is offered ways to use Ushm with a cartridge.

  • Drilling in hard.To.Reach places is possible thanks to the angular gearbox of a grinding machine. Ushm includes a much less workspace with a cartridge, in comparison with the drill.
  • In the presence of a control regulator in the cartridge, you can fix the bat from the screwdriver, which will also allow you to get to hard.To.Reach places.
  • Clutching the cartridge holder of the end keys. We get a good gaykowert. Revolutions control. Required.
  • If you fix an abrasive ball in the cartridge, you can clean in hard.To.Reach places. It is noteworthy that this device will work much more effective than on a simple drill. In this case, everything solves high speeds, the device can be used without a speed regulator.
  • If you fix a flexible sleeve with a zanga under engraver cutters, we get a powerful drill. Graver nozzles can be attached directly in the cartridge, without using a flexible extension cord.
  • Another cartridge can be used to fix the woodworking onion cutter. There are several options: a) you can additionally make a movable supporting plate. As a result, we get a full manual run.In machine; b) in addition to the above improvements, you can hardly fix the grinder with a cartridge up. You get a stationary milling mill. 10 thousand. Rpm. Optimal indicator for milling machine.
  • Clutching the diamond cutter, you can process a stone, but then you can definitely need a speed adjustment.

The listed options for use are far from the limit. Here the ingenuity of the master comes first. But, as you can see, a revolution regulator is very useful for this layout. Often, regulators installed on angular grinding machines at low speeds do not provide stable operation of the power tool. It is advisable to purchase a universal regulator (dimmer), combined with a power outlet. Over, this device does not differ in a high price. For those who are friends with a soldering iron and have basic knowledge in electronics, there are many simple and original schemes. Sometimes homemans in their indicators are much superior to products from the Middle Kingdom.

Findings

Ushm. A simple and useful tool for home or professional use. The most common problem while working with it is the bite of the nut that holds the disk. You can cope with this with the help of mechanical exposure to the mechanism (attacks on mounting, using a lever and stealing a disk), and chemical methods. Processing threads with oil or a solvent of rust.

Quick Tip. Carving with Harbor Freight Cup Wheel

This simple operation sometimes at a standstill of even experienced locksmiths or users of a grinder. The reason is that the disk is fixed by a special nut. There are 2 or 4 holes on the nut, into which a special key is inserted. This key has always been attached when buying a grinder. Perhaps he is still included in the sets.

According to the instructions for the grinder, click on the latch, which is located on the back of the gearbox. When the shaft is fixed, you need to unscrew the nut with a special key and change the disk. But it is difficult to promote the nut if it was not squeezed. And pinches it with such a nut almost always. An attempt to unscrew the disk leads to a breakdown of the fixator outside the gearbox.

What is the carving on the grinder. STEPMEB.Ru

The clamping nut on Bulgarian

The disk is spinning clockwise. The nut should also be twisted by the time, as it is still called against?

The nut clock, not a single one has been unscrewed, but quite the opposite.

Construction. This is when always something to do.

The nut is tightened clockwise. What a thread On the pedals of the bicycle? Right or left. Stall normally do not tighten the shaft. Often like oil does not want to unscrew than flies. Only once I had to disassemble my whole head at the grinder (at the same time I did not smell it) to twist it, the disk did not drag out so that I bent two keys (they were flimsy some).

H.S. Which Bulgarian spindle thread? That he refers this to the grinder and stupidly copied. Do not be too lazy to put on protection

Photos of accidents with a grinder eighteen!! Http: // handsurg.Org.UA/Index.PHP?Option = COM_DATSOGALLYETEMID = 26FUNC = WMARKMID = 209

Do not think that the construction will ever end.

The secret of light unscrewing the disk on

Bulgarian. [Life situations]

Here the video can be seen, just as and what, to clamp on the right Bulgarian. How to correctly change the nozzle on a grinder. What a thread on the spindle. Right or. This chip will help you get rid of

)))))))))))))))))? Clockwork. Nut, and the disk should spin towards.

If it is specifically bites, the divorce key can be unscrewed.

Когда разобрал голову и с другого конца зажал в тисках, открутил только газовым ключиком

It is naive to believe that the construction will ever end.

Cardboard circles help from biting, I currently with my hands in 99%. Stop with a button, and you turn away right behind the disk, there have never been problems.

And I heard that welded ones specially make the disk in another strip spin, but why? Don’t know.

An arrow is knocked out on a grinder (on the case). What is the thread on the spindle of the grinder?- forum. This is what side it is shown. In that direction and the disk is spinning. And in that direction you need to tighten the disk. To do this, just just hand the disk with your hand. All the nut is pulled on the nut right thread.

If sparks fly on you. Then the right thread and when impact (pulling out of the hands of the grinder) there is an automatic tightening of the thread.

pitch, carving, grinder

If sparks come from you. Disk when not complete tightening. Will be unscrewed. To avoid when your grinder knocked out of your hands and jammed the nut. It is necessary to put a cardboard gasket between the disk and nut (even from the pack of cigarettes will go)

Cartridge for a grinder, the use of an adapter (adapter)

The corner grinding machine (Bulgarian) has become an integral part of both home workshops and large enterprises. No wonder. High performance, wide functionality, a high number of revolutions on the spindle and a relatively low weight made Ushm leader in metal processing and other materials.

But progress does not stand still. New devices to expand the capabilities of the device are constantly on sale. One of these adapters allows you to install a clamping cartridge on a grinder. What will come of this and how to safely use such a tool is proposed to be considered in more detail in the context of this article.

  • The adapter device
  • Installation of a cartridge on a grinder
  • What you need to know about the grinder to use it together with the cartridge
  • Areas of the use of corner grinding machine
  • Safety precautions

The adapter device

The adapter itself does not represent a special constructive complexity. As a rule, it is embedded from the hexagon for the convenience of fixing with an open wrench when installing, and especially removal. On one side, the internal thread M14 is cut. It is designed to wind up an outer thread of the corner grinding machine spindle. The other end is protected for the standard external thread M12 corresponding to the thread of the clamping cartridge. A hole is drilled from the end and the left thread is cut under the bolt for additional fastening.

There are also conical pure adapters. Ushm for appropriate cartridges with conical fixation.

Installation of a cartridge on a grinder

To install the cartridge on the grinder, it is necessary to perform the following actions:

  • An adapter is screwed on the “naked” spindle of the angular grinding machine
  • At the other end of the adapter, the cartridge is wound
  • Previously dismissing the lip of the slope of the drill, a bolt of additional fixation is screwed up. This operation is convenient to carry out a screwdriver with a magnetized tip.

Note! All threaded connections should immediately be squeezed well. Since the system is “self.Settled” during rotation, it is necessary to exclude free thread on the thread during the starting jerk. Otherwise, the high.Speed machine is able to tighten the threads to such an extent that you can cut off the lock on the grinder when promoting. If it turned out to be excessive clamping, it is better to disassemble the Ushm gearbox and promote, after holding the gear in a vice.

What you need to know about the grinder to use it together with the cartridge

Before ordering this adapter, it is advisable to familiarize yourself with some features of corner grinding machines:

Depending on the model, the turns on the spindle of the grinder can fluctuate from 6 thousand. Up to 12 thousand. Rpm. In comparison with a conventional drill, this is, to put it mildly, a lot. For normal operation of the drill, on average, 300–900 rpm is necessary.

Many manufacturers equip their products with a speed regulator. In some cases, it is simply necessary. For example, when using Velcro disk for abrasive circles on a fabric base or when working with fiber circles. Such modifications are the most suitable for installing the clamping cartridge of the drill.

If it is decided to install the cartridge, then it is necessary to take into account these features. Without a revolution regulator, using a grinder instead of a drill, we get an excellent “drill killer”. By the way, if you have the necessary knowledge and skills, there is the possibility of an independent installation of a revolution regulator.

pitch, carving, grinder

Areas of the use of corner grinding machine

At first glance, this “application” may seem completely superfluous, as it has very limited functionality. But is it? Your attention is offered ways to use Ushm with a cartridge.

  • Drilling in hard.To.Reach places is possible thanks to the angular gearbox of a grinding machine. Ushm includes a much less workspace with a cartridge, in comparison with the drill.
  • In the presence of a control regulator in the cartridge, you can fix the bat from the screwdriver, which will also allow you to get to hard.To.Reach places.
  • Clutching the cartridge holder of the end keys. We get a good gaykowert. Revolutions control. Required.
  • If you fix an abrasive ball in the cartridge, you can clean in hard.To.Reach places. It is noteworthy that this device will work much more effective than on a simple drill. In this case, everything solves high speeds, the device can be used without a speed regulator.
  • If you fix a flexible sleeve with a zanga under engraver cutters, we get a powerful drill. Graver nozzles can be attached directly in the cartridge, without using a flexible extension cord.
  • Another cartridge can be used to fix the woodworking onion cutter. There are several options: a) you can additionally make a movable supporting plate. As a result, we get a full manual run.In machine; b) in addition to the above improvements, you can hardly fix the grinder with a cartridge up. You get a stationary milling mill. 10 thousand. Rpm. Optimal indicator for milling machine.
  • Clutching the diamond cutter, you can process a stone, but then you can definitely need a speed adjustment.

The listed options for use are far from the limit. Here the ingenuity of the master comes first. But, as you can see, a revolution regulator is very useful for this layout. Often, regulators installed on angular grinding machines at low speeds do not provide stable operation of the power tool. It is advisable to purchase a universal regulator (dimmer), combined with a power outlet. Over, this device does not differ in a high price. For those who are friends with a soldering iron and have basic knowledge in electronics, there are many simple and original schemes. Sometimes homemans in their indicators are much superior to products from the Middle Kingdom.

Nuts for bells

All products choose a store Show:
Sort by: popularity rating increase in price decreasing prices Display: 20 40 80 goods

Helpful information

Here you can choose nuts for the Bulgarians necessary for fixing the disc on the spindle. If the factory nut is damaged or lost, choose the equipment based on the tool model, taking into account its main parameters. A properly selected nut provides a reliable mount for equipment, reduces the beating of the disk and increases the safety of work.

Choice parameters

Type. There are fast.Sounding nuts for Ushm that do not require the use of the tool during installation, and there are nuts for fixing the key. Depending on the type of equipment to a particular model of a grinder, choose a nut of the corresponding type.

Thread. To fix the element on the spindle, it is necessary to choose the appropriate thread diameter. The most common standard thread M14.

Disk diameter. Each fast.Sounding nut for grinder is designed to keep the equipment of a certain size, for example, with a diameter of 180 to 230 mm or from 115 to 150 mm.

Pitch

I am interested in t.To. It is necessary through third hands (not always understanding) to explain to the turner which thread to cut in the cartridge. And all the Bulgarians (mostly are interested in small ones) is the same?

The thread is the same everywhere. M14 with a standard step.

2is thanks, otherwise I already bought the cartridge on which M12x2 is written.5 (I write from memory) I thought about the step, and I measured m14 with a rod!

2peter m. You can say the turner M14x2, this will be enough, plus the length.

To peter m. The cartridge on which is written m12x2.5 (I write from memory)

And there is definitely a step 2 mm? I know for sure that the standard step for M12 1.75 mm, and for M16. 2 mm, but for M14 I do not remember. But the fact that the Bulgarian has a step M14 is standard, that’s for sure.

2is Just specially measured 100%. Bulgarian Mil AG9-125MX, domestic threaded.

Dr.No wrote: 2peter m. You can say the turner M14x2, this will be enough, plus the length.

Thanks again for exhaustive information! I will only say not me, but a woman so it will be better to write all this on a piece of paper.

And such a question for reference. Whether the cartridge from the drill at 10,000 about. Which are developing a grinder? Otherwise I am all this to a greater extent to use the existing flexible drive with the Outstrack from the Dremel.

Peter m. Do not be afraid to subsequently wrap up on this cable?

pitch, carving, grinder

M121.25 is a small thread (for car candles), but I don’t really believe something in 2 mm, most likely it should be-1.75.

TSN wrote: Most likely it should be. 1.75.

I got to the directory. Standard step: M101.5, M121.75, M142, M162. Over, according to GOST, M10, M12 and M16 are the first row (preferred), and M14 is the second row (there is another third row, there is exotic type M11 and M15). For spark plugs, M14 with a small step is used: M141.25. The standard of domestic cartridges for driving m121.25.

TSN wrote: M121.25 is a small thread (for car candles), but I don’t really believe something in 2 mm, most likely it should be-1.75.

Dr.No absolutely right on the spindle Ushm thread M14x2 (main) And in car candles (not to know ashamed) M14x1.25

It’s guilty, at the expense of candles. Of course 14 mm, just Ivan wrote M121.25. I thought that he attributed this to the grinder and stupidly copied, paying attention only to a step, but did not look at the diameter.

There is another third row, there is exotic type M11 and M15).

Which should be twisted with keys to 15 and 20 would kill these standardizers. Keys for 5.5, 7, 8, 9, 10, 11, 12, 13, 14, 15, 17, 18, 19, 20, 21, 22, 24! Seventeen varieties, and everything is found, everything must have to be able to be able to do this row. Sorry for the off

Peter m. Wrote: Whether the cartridge from the drill at 10,000 about. Which are developing a grinder?

2serg thanks, I expected your answer! Now the question is removed, you can contact the turner with a calm soul.

Cut the thread?? As in the years has shown instrument?? I will also give the cartridge tokar, for cutting threads.

They say he plays the cartridge slightly, to make an analogue of the milling cutter will not work. Instead of a corner drill to Bolene I have a bell with my native thread M121.25 I’ll look there, but until my hands reached

Crazyalone wrote: they say plays the cartridge slightly

The adapter must be sharpened. And should do a Smart turnerInner thread is cut in the blank, under the spindle of the grinderThe thread is pulled out by the cutter, the blank is tightly welded and the outer is pulled out, under the cartridge. This will not beat like that.

The essence of the idea is to put a cartridge on a grinder and drill in uncomfortable places due to a small length. All adapters are completely. It’s easier to buy a drill or milling mill at once. The internal thread for the spindle is perfectly cut in the cartridge, there the problem is that the metric carvings of the tolerance are not like that small, on which cartridges and ts are screwed. Simply because it is designed for collapsible fasteners, which can be corroded. And must still be unscrewed and twist. Too tightly made thread simply will not climb in this case.

Crazyalone wrote: There the problem is that the metric carvings of tolerances are not like that small, on which cartridges and ts are wound.

Wood Carving Chain Disc Demo 2021- Does it work ?

Cartridges are wound not on some special thread. This is an ordinary inch thread, only with a small step. Inch 1/2 x 20 UF diameter (nominal. ) 12.7 mm, step. 1.27mm Metric m12 x 1.25 diameter (nominal. ) 12 mm, step 1.25mm The accuracy of the metric thread (however, like inch) does not depend on the size and step.

How to unscrew the nut of the disk on the grinder (Ushm) if it is jammed?

I can’t unscrew the nut on the grinder (Ushm).

How to unscrew the protracted nut-flanets on a grinder (Ushm)?

A disk broke on a grinder (Ushm), and the nut dragged on. How to unscrew it?

I will tell you the simplest and most convenient method of unscrewing such a nut- “jammed”. This method will not demand from you something additional (where to get a vice working in the basement, somewhere on the road, or a gas key, a chisel, etc.D.). Yes, and the chisel is not the best way out, how much I have grown over the Bulgarians with the “ducked” nuts, with broken stoppers. It’s scary to look at them. Heating is the right direction (proposed). But the wrong execution method. I think it will not be difficult to break the disk to the base of the nut, then we find in a wooden block, or something like that, turn on the grinder and nut, as it were. As a rule, there are enough minutes for good heating, the nut is unscrewed by “once”. One inconvenience, can “need”.

Mini Grinder Showcase Video

Learning to remove threaded cartridges from drills and screwdrivers important nuances

Nozzles on a grinder for grinding wood: varieties and choices of choice

At first it should be noted that by type of fixation of the elements considered on the shaft of power tools, they are classified into threaded and conical. Threaded ones are more popular, but conical devices are considered reliable. Conical mounts are used on drifts and drilling machines.

If a threaded type is on a drill, then it will not be difficult to remove it, if you know one main feature. Before taking off the cartridge from the drill, you should know that it is screwed in a non.Standard way. To remove such an element from a drill or screwdriver, you will need to act according to the following instructions:

To unclench the lips as much as possible so that access to the inner part of the element is opened

Inside is a fixing screw. This screw has a non.Standard thread. Left

To unscrew it, you need to apply the force not in the right, but the left side of the screws have a different design of the hat, so to find out which screwdriver you need to twist it, you should highlight and look inside the device

If the device is unscrewed from the screwdriver, then it is very important to transfer the rattle or the regulator to the maximum mode. If this is not done, then it will not be possible to twist the cartridge from the shaft

After the screw is removed, it remains to twist the cartridge from the drill. He divorces to the left side (t.E. Fine)

If there is no fixing screw inside the drill cartridge, then to dismantle the part, you just need to twist the part from the shaft. To do this, you will need an open key for “14”, as well as a trumpet key, and make a little physical effort. With an open key, the shaft between the tool body and the cartridge is fixed, and the twisted element itself rotates with a pipe tool.

When carrying out work, it is recommended to use the lubrication of WD-40. In such ways, devices are removed on many drums and screwdrivers. However, there are executive organs that have a conical joint design. How conical devices are removed, we will consider further.

What a carvings on a grinder?

The corner grinding machine (Bulgarian) has become an integral part of both home workshops and large enterprises. No wonder. High performance, wide functionality, a high number of revolutions on the spindle and a relatively low weight made Ushm leader in metal processing and other materials.

But progress does not stand still. New devices to expand the capabilities of the device are constantly on sale. One of these adapters allows you to install a clamping cartridge on a grinder. What will come of this and how to safely use such a tool is proposed to be considered in more detail in the context of this article.

  • The adapter device
  • Installation of a cartridge on a grinder
  • What you need to know about the grinder to use it together with the cartridge
  • Areas of the use of corner grinding machine
  • Safety precautions

The adapter device

The adapter itself does not represent a special constructive complexity. As a rule, it is embedded from the hexagon for the convenience of fixing with an open wrench when installing, and especially removal. On one side, the internal thread M14 is cut.

It is designed to wind up an outer thread of the corner grinding machine spindle. The other end is protected for the standard external thread M12 corresponding to the thread of the clamping cartridge.

A hole is drilled from the end and the left thread is cut under the bolt for additional fastening.

Attention! The standard of cartridge thread M12, although the most common, is far from the only. When choosing an adapter, pay attention to the marking of the selected cartridge, at least you can come across a couple more standard threads: M12 × 1.25 and 1/2. 20 UF.

There are also conical pure adapters. Ushm for appropriate cartridges with conical fixation.

Installation of a cartridge on a grinder

To install the cartridge on the grinder, it is necessary to perform the following actions:

  • An adapter is screwed on the “naked” spindle of the angular grinding machine
  • At the other end of the adapter, the cartridge is wound
  • Previously dismissing the lip of the slope of the drill, a bolt of additional fixation is screwed up. This operation is convenient to carry out a screwdriver with a magnetized tip.

Note! All threaded connections should immediately be squeezed well. Since the system is “self.Settled” during rotation, it is necessary to exclude free thread on the thread during the starting jerk.

Cartridge for a grinder, the use of an adapter (adapter)

The corner grinding machine (Bulgarian) has become an integral part of both home workshops and large enterprises. No wonder. High performance, wide functionality, a high number of revolutions on the spindle and a relatively low weight made Ushm leader in metal processing and other materials.

But progress does not stand still. New devices to expand the capabilities of the device are constantly on sale. One of these adapters allows you to install a clamping cartridge on a grinder. What will come of this and how to safely use such a tool is proposed to be considered in more detail in the context of this article.

  • The adapter device
  • Installation of a cartridge on a grinder
  • What you need to know about the grinder to use it together with the cartridge
  • Areas of the use of corner grinding machine
  • Safety precautions

Safety precautions

Having fixed the clamping cartridge on the corner grinding machine. We get a powerful, convenient, universal tool, which, by negligence of the owner, is able to cause irreparable harm to human health. Pay special attention to this section. Knowledge of elementary safety regulations can get rid of serious problems.

  • Grinding machines, due to their targeted use, are not equipped with “rattles”, like screwdrivers, or emergency stop systems (they are sometimes found on grinds). This means that with any jamming of the tool fixed in the cartridge, the rotational movement will be transmitted to the power tool case, which can seriously injure the operator’s hands. It is advisable not to use powerful machines. If Ushm is up to 800 watts, a person will keep the average complexion without problems, then a tool of 2.5 kW when jamming becomes uncontrollable.
  • Use personal protective equipment (PPE). How to not regret to state, but our compatriots are very disregarded to this point. And this is with many examples of damage to the eyes, hands injuries and the like. Probably everyone who worked with a grinder may recall more than one similar case that happened to them or their acquaintances. Do not be lazy to use glasses, gloves, headphones and, if necessary, respirator.
  • It must also be understood that the instrument contains details rotating at high speed that can in an instant to wrap up any material that fell into their area of ​​action. For this reason, overalls are necessary, with sleeves tightly adjacent to the wrists. Excluded work with hanging parts is excluded. It is forbidden to work in three.Fingered mittens. If necessary, use working gloves made of genuine leather or substitute.
  • Adapter plus a cartridge with a clamped tool will significantly shift the vectors of efforts during operation. This means that your angular grinding machine will behave in a completely different way, in comparison with the classic use. Having installed this nozzle, first you need to adapt to new dynamics in the operation of the power tool. Over, each interchangeable nozzle will add innovations to work. First time start the minimum speed, gradually increasing them.

TB rules are not something special. In principle, they are applicable to almost the entire line of manual power tools.

In conclusion, one can say one thing. Any serious master tries to expand the capabilities of his tool. In the case of an adapter under the cartridge, the functionality of the grinder increases incredibly, but even more entertaining yourself to come up with how else you can use such a complete set.

I discovered on the Internet such a saitk Kassoniks.Ru, on which drill cartridges for the spindle of the grinder are sold As one day, such an adaptation was very urgently needed, but having run around the shops, I never found this giddle and in general all the sellers were surprised and answered that it was never on sale of such cartridges. I decided to look on the Internet, and also underwent a certain fiasco. This is a fiasco brother))) Goggling the entire Internet, as a result, he could not find anywhere on sale. In general, he reconciled with this and left this venture And somehow one day again, I needed this device, well, again, all the roads brought me to the Internet and again googling a little on the internet, suddenly happened. Oh miracle! This time I was overtaken precisely. O Happiness! Right immediately, on the move, the search engine gives me this wonderful modest site. Kassoniks.Ru, where the coveted adaptation awaits me unpretentiously! Of course I darted immediately to buy this happiness for myself))) When the package reached me, I immediately rushed to check and measure the cartridge on my Bulgarian And how well everything was pancake fit. Having wound a cartridge on the Ushm, I checked this device right away in work And how various nozzles behave in this cartridge. All sorts of balls there, they would have been shrugged and various mills and all sorts of marines And here is the most interesting thing, this is what is in This cartridge was perfectly suitable for a flexible shaft. It turned out a bad bourgeois ! Literally in a matter of seconds, I realized that I incredibly expanded the possibilities of my grinder I realized 100% and made sure that this was just the same as I needed. Now this stray is always in my case with a Bulgarian, with me to all types of work.

What I recommend to everyone! FRIENDS! I wrote this fiction will simply share with all the men, because in the know that many such a bubbling is looking everywhere and cannot find it anywhere ! And on that site there is so I recommend stagnant in the above Internet magaz and use this placement for yourself in the convenience of work!))) All success and good luck!

Safety precautions

Having fixed the clamping cartridge on the corner grinding machine. We get a powerful, convenient, universal tool, which, by negligence of the owner, is able to cause irreparable harm to human health. Pay special attention to this section. Knowledge of elementary safety regulations can get rid of serious problems.

  • Grinding machines, due to their targeted use, are not equipped with “rattles”, like screwdrivers, or emergency stop systems (they are sometimes found on grinds). This means that with any jamming of the tool fixed in the cartridge, the rotational movement will be transmitted to the power tool case, which can seriously injure the operator’s hands. It is advisable not to use powerful machines. If Ushm is up to 800 watts, a person will keep the average complexion without problems, then a tool of 2.5 kW when jamming becomes uncontrollable.
  • Use personal protective equipment (PPE). How to not regret to state, but our compatriots are very disregarded to this point. And this is with many examples of damage to the eyes, hands injuries and the like. Probably everyone who worked with a grinder may recall more than one similar case that happened to them or their acquaintances. Do not be lazy to use glasses, gloves, headphones and, if necessary, respirator.
  • It must also be understood that the instrument contains details rotating at high speed that can in an instant to wrap up any material that fell into their area of ​​action. For this reason, overalls are necessary, with sleeves tightly adjacent to the wrists. Excluded work with hanging parts is excluded. It is forbidden to work in three.Fingered mittens. If necessary, use working gloves made of genuine leather or substitute.
  • Adapter plus a cartridge with a clamped tool will significantly shift the vectors of efforts during operation. This means that your angular grinding machine will behave in a completely different way, in comparison with the classic use. Having installed this nozzle, first you need to adapt to new dynamics in the operation of the power tool. Over, each interchangeable nozzle will add innovations to work. First time start the minimum speed, gradually increasing them.

TB rules are not something special. In principle, they are applicable to almost the entire line of manual power tools.

In conclusion, one can say one thing. Any serious master tries to expand the capabilities of his tool. In the case of an adapter under the cartridge, the functionality of the grinder increases incredibly, but even more entertaining yourself to come up with how else you can use such a complete set.

Safety precautions

Having fixed the clamping cartridge on the corner grinding machine. We get a powerful, convenient, universal tool, which, by negligence of the owner, is able to cause irreparable harm to human health. Pay special attention to this section. Knowledge of elementary safety regulations can get rid of serious problems.

  • Grinding machines, due to their targeted use, are not equipped with “rattles”, like screwdrivers, or emergency stop systems (they are sometimes found on grinds). This means that with any jamming of the tool fixed in the cartridge, the rotational movement will be transmitted to the power tool case, which can seriously injure the operator’s hands. It is advisable not to use powerful machines. If Ushm is up to 800 watts, a person will keep the average complexion without problems, then a tool of 2.5 kW when jamming becomes uncontrollable.
  • Use personal protective equipment (PPE). How to not regret to state, but our compatriots are very disregarded to this point. And this is with many examples of damage to the eyes, hands injuries and the like. Probably everyone who worked with a grinder may recall more than one similar case that happened to them or their acquaintances. Do not be lazy to use glasses, gloves, headphones and, if necessary, respirator.
  • It must also be understood that the instrument contains details rotating at high speed that can in an instant to wrap up any material that fell into their area of ​​action. For this reason, overalls are necessary, with sleeves tightly adjacent to the wrists. Excluded work with hanging parts is excluded. It is forbidden to work in three.Fingered mittens. If necessary, use working gloves made of genuine leather or substitute.
  • Adapter plus a cartridge with a clamped tool will significantly shift the vectors of efforts during operation. This means that your angular grinding machine will behave in a completely different way, in comparison with the classic use. Having installed this nozzle, first you need to adapt to new dynamics in the operation of the power tool. Over, each interchangeable nozzle will add innovations to work. First time start the minimum speed, gradually increasing them.