What oil for a chainsaw. Oil for twostroke engines STIHL HP

What kind of oil is it to choose for a chainsaw

The line of oils for lubrication of the chain includes three types of products, this is:

When working, it is necessary to use the type of lubricant that matches the conditions and duration of work as much as possible. Consider each of the oils for the Calm chain Read more.

Forestplus

Forestplus mineral oil for lubrication of the chain, it is a quality product that creates a reliable film on the tires and on the links of the chain, which is well held at the maximum speed of rotation of the chain.

Sets in three types of containers, a liter bottle and canists of five and twenty liters.

Forestplus has the lowest expiration date among the oil line oils, which is only three years subject to storage conditions.

BIOPLUS oil review overview

Bioplus is made on a plant basis, which allows it to decompose when it enters the soil for the minimum time. It is this property that is marked by the European sign of environmental safety. According to information that is available on the manufacturer’s website and is official, Bioplus has been tested according to OECD 301 b.

For maximum convenience of consumers, it faces 4 types of containers, this is:

• Liter bottle.
• CANISTRET three liters.
• A five.Liter canister.
• A plastic twenty.Liter canister for those who work as a chainsaw daily and spend a large number of lubricants.

The price of Bioplus may vary depending on the region of sale.

Bioplus shelf life is four years. Brown colour.

Synthplus

Synthplus is a semi.Synthetic oil that retains its properties even under the most difficult conditions. It is able to maintain working characteristics at a temperature of minus 25 degrees. Synthplus mixes well with Bioplus, which will easily move from one type of oil to another.

Synthplus, has a high shelf life, which, with proper storage, reaches seven years. Synthplus oil color, brown.

Shtil Synthplus is packaged in a container of similar container as Bioplus.

The principle of lubrication of the chain and tire

The main block of the system is the pump. The principle of its work is as follows. Когда частота вращения двигателя увеличивается, шестерня, установленная на главном валу, приводит вал насоса через червячную шестерню. In turn, the rotation of the shaft creates a certain pressure in the oil line, which makes the oil move along it towards the bus.

• Oil tank (located in the crankcase, oil needs to be poured into it so that it comes to the chain);
• Oil filter (installed inside the tank);
• Oil pipeline or oil.Conducting hose (made of rubber resistant to wear);
• Oil pump;
• Gear of worm gear;
• The tire of the chainsaw (it contains holes through which oil comes).

The oil channel ends where the chainsaw crankcase is in contact with the tire. There is a longitudinal groove in this site. When the tire is installed on the chainsaw, the oil channel coincides with this groove. The groove regulates the flow of oil to the tire of the chainsaw, and its number is in no way related to the degree of tension of the chain.

After the oil enters the tire, the chain is involved. It usually has holes from which the oil falls on the entire plane of the tire. The higher the number of roller roller speeds, the more oil will enter the circuit. Some models of chainsaws have special adjusting oil pumps, with which you can adjust the amount of oil entering the chain. This is how the degree of lubricant consumption is adjusted.

Shtil oil for use in two.Stroke engines

What is the difference between a large manufacturer and a company that sticks its nameplate on products, it is not clear where and it is not clear who? Probably one of the main differences is that in addition to some basic products, for example, an electric tool, a serious manufacturer produces materials and components to ensure the work of the main products.

All this can be fully attributed to the company STIHL (Shtil). This company has been the design and production of various electric and gasoline semi.Professional tools for many years, which does not need to represent. It can be found in the hands of summer residents, professional builders, lumberjacks and workers of other specialties.

The company has long mastered the production of saws, accessories for them. But the company went further and mastered the production of working fluids specially designed for uninterrupted, and most importantly, safe operation of its products. But I must say that these oils and lubricants can be successfully used to ensure the operation of the tool for the production of other companies that produce similar products.

The consumer may be sure that the company’s products will not let the company not let down in any case.

Correct proportions

Most often, when preparing fuel for the work of saw, 1:50 and 1:40 are used to work. This means that one part of the oil is added to 50 or 40 parts of gasoline. Calculations are made as follows: 1 l = 1000 ml, 1000/50 = 20 ml or 1000/40 = 25 ml, that is, in the first case, pour 20 ml into each liter of gasoline, and in the second. 25 ml of oil. If there is no instructions and you do not know the proportion to prepare the mixture, then use the following recommendations:

• Tool and oil of one brand. For example, for the Shtil chainsaw, the ratio of gasoline and STIHL oil will be the same as indicated on a container with butter, usually 1:50.
• The substances used for the mixture have different brands. The proportion of 1:40 is selected.
• There is one brand, but there is no information about the ratio of substances on the oil. They are divorced 1:40.
• In the absence of any data on the saw and oil, the mixture is bred in a proportion of 1:40. The only thing you need to make sure that the oil is intended for two.Stroke engines.

To carry out the run.In a new saw at the first three gas stations with fuel oil, add 20% more. In this case, instead of a ratio of 1:50, it will be 1:42, and the proportion 1:40 turns at 1:33. 24 or 33 ml of oil, respectively, will require a liter of gasoline. Other countless events with a new saw do not conduct. Manufacturers advise working only at the largest speeds always. After the instrument run, the usual proportions are used 1:50 or 1:40. In some cases, the manufacturer of the equipment also indicates other ratios, for example, 1:25 or 1:32, they must be observed.

The principle of lubrication of the chain and tire

The main block of the system is the pump. The principle of its work is as follows. Когда частота вращения двигателя увеличивается, шестерня, установленная на главном валу, приводит вал насоса через червячную шестерню. In turn, the rotation of the shaft creates a certain pressure in the oil line, which makes the oil move along it towards the bus.

• Oil tank (located in the crankcase, oil needs to be poured into it so that it comes to the chain);
• Oil filter (installed inside the tank);
• Oil pipeline or oil.Conducting hose (made of rubber resistant to wear);
• Oil pump;
• Gear of worm gear;
• The tire of the chainsaw (it contains holes through which oil comes).

The oil channel ends where the chainsaw crankcase is in contact with the tire. There is a longitudinal groove in this site. When the tire is installed on the chainsaw, the oil channel coincides with this groove. The groove regulates the flow of oil to the tire of the chainsaw, and its number is in no way related to the degree of tension of the chain.

After the oil enters the tire, the chain is involved. It usually has holes from which the oil falls on the entire plane of the tire. The higher the number of roller roller speeds, the more oil will enter the circuit. Some models of chainsaws have special adjusting oil pumps, with which you can adjust the amount of oil entering the chain. This is how the degree of lubricant consumption is adjusted.

Oil for chainsaw

To begin with, it would be nice to mention that all the chainsaws were created with quite small sizes, but with their dimensions, they have a very impressive power. Thanks to this feature, the chainsaws are in great demand.

Despite the high quality, durability of the chainsaw depends on the use of the correct lubricant and fuel. The first problematic question that the owners of this technique face is: what kind of oil and fuel to choose for their chainsaw? In this article you will learn about which oil is better to use for your chainsaw, and about which fuel is better to fill in your “baby”.

Choose oil for chainsaw oil

The first thing you should know about is that almost all the romances of the calm are equipped with a carburetor two.Stroke engine. There are also two separate tank in them: the first for oil, and the second for gasoline.

The first, and most importantly, remember that a simple oil is poured in the model of domestic production, which is usually poured into the tanks of motorcycles, and their proportion should be no more than 1 to 25. As for the chainsaws produced abroad, they will need to buy branded oils, the proportion for which is 1 to 40. Of course, you can try to pour oil for domestic saws in an imported saw, in which case, the power of your tool may noticeably fall. The best advice that can be given when buying oil for such a technique is to contact the manual to use your tool.

A good choice will be synthetic oil for two-stroke air cooling engines of the API-TB and API-TC class. Having come to the store, ask the seller about the presence of such brands as STIHL, Husqvarna, Hahotek, Champion, Alco, etc. In no case do not greedy on the ingredients, it is better to spend money on a quality product than then spend a lot of money on repairs.

Choose gasoline for a chainsaw calm

When choosing gasoline for its chainsaw, you should pay attention to, of course, the quality of the gasoline itself and, its octane number. It is best to take gasoline with octane AI92

You can try AI95, but too many questions arise about its quality. If you doubt the quality of AI95, then AI92 will be the best choice for you.

We do not advise you to use gasoline, which has long been in any container for a long time, whether it be a canister, tank or something else. For the fuel mixture, only fresh gasoline must be used, otherwise, it can lose all its useful qualities: octane number, etc. If you still use not fresh gasoline, then your chainsaw will work at incomplete power. In the case of a rude breakdown, due to the use of such fuel, you will have to spend a lot of money on its repair, since such a case does not apply to warranty, and you will better purchase a new tool.

Making the fuel mixture of gasoline and oil

Before proceeding with the creation of the fuel mixture for the ribbon of the manufacturer Shtil, pay your attention to the manual from the manufacturer. Why do you need to do this? The thing is that with insufficient oil content in gasoline, the cylinder and the piston will heat up hard, which will occur in the bullying, which will lead to a breakdown of the CPG, and as a result-to expensive repair

In order to prepare a high.Quality fuel mixture, you need to mix oil and gasoline in a clearly verified proportion. If the oils are more than necessary, then this can lead to the appearance of soot on pistons and candles. If you overdo it a little with gasoline, then expect the ambulance of your engine. For example, on average, one liter of gasoline should be mixed with 20-50 ml. Oils. For a train, it is recommended to pour 4 liters. Gasoline. 100 ml. Oils. In this ratio, a mixture for chainsaws is prepared up to 1.5 kW. If the power is more than 1.5 kW, 100 ml should be poured. Oils for 5 liters. Gasoline. But these are all approximate calculations, always use the proportions indicated in the manual to your saw, if you yourself do not understand how much and what is needed. But do not really believe the numbers indicated on the oil label.

Conclusion

We examined all the oil line oils, and found out that the most popular lubricant for 2 strokes is STIHL HP. It is it that needs to be used in ordinary conditions, t. To. At the same time you do not have to overpay, and the engine will be reliably protected.

The saw chain, ordinary users, must be lubricated using Bioplus, t. To. The remaining options are intended for difficult conditions or work in the winter period. Also, we figured out that the correct ratio of gasoline with butter is 1:50, but during the period of the time it can be slightly changed and the mixture is made in a proportion of 1:40, t. E. 25 ml per 1 liter of gasoline. We learned how to distinguish a fake of Bioplus Calm from the original.

Oil for two.Stroke chainsaw engines

Modern garden chain saws can be pre-equipped with 2- and 4-stroke power units. The engines of these two types are slightly different in terms of action and the scheme for using the added lubricant material. In powerful gross chainsaws with a 4-stroke ICE, the engine crooked-shawl is lubricated with oil, which is in the crankcase of the factory motor during the active operation of the gas tools. In 2-stroke factory ICE, the lubricant comes from gasoline directly to the cavity located under the standard piston-it is there that there is a crooked-shaped group equipped with a pair of bushings and bearings requiring continuous lubricant. That is why in the gasoline used for refueling for 2-stroke factory ICE you need to add motor oil.

In order to accurately choose a specific lubricant for the continuously rubbing parts of the power supply of the chainsaw, its owner must study the most important properties of the material:

• The volumes of the resulting ash. During the combustion of gasoline, the exhaust gas vapors appear, and when combustion of oil. Ash and tarry deposits. They accumulate on the walls of the cylinder and the piston, which makes it difficult to make its unhindered movement up and down. Some manufacturers do not guarantee sufficient grease combustion, however, branded products are almost completely burned;
• The level of purification from extraneous impurities. In the composition of oils, may contain not only useful additives, but also harmful substances. A lubricant is considered high.Quality, in which the percentage of harmful components will be minimal;
• Anti.Dimensional, anti.Corrosion and continuously lubricating properties. The oil should cover the rubbing parts of the power unit with a thin film, thereby protecting them from increased wear, heating and exposure to rust.

When developing lubricants to maintain the operation of 2-stroke engines, manufacturers are guided by 2 standard: 2T and TC-W3. The second type of oil is used for operation in standard engines equipped with liquid cooling. Such an internal combustion engine is equipped with hydraulic cycers and boat engines. 2T standard oils are used mainly for lubricating engines with constant air cooling. Chainsaws, trimmers and other types of household appliances.

In the market, oils of such brands are the most popular among experienced gardeners and rollers:

Husqvarna. This Swedish manufacturer never saves on quality. Direct evidence of this is not only a proprietary garden technique, but also high.Quality products for lubricating its parts. The oil of this brand. Husqvarna HP. Contains a large number of additives aimed at stabilizing the work of the internal combustion engine. This oil is produced on a carefully prepared semi.Synthetic basis and has substances that reliably protect the power unit from corrosion and increased wear. During continuous operation, the lubrication of the Swedish manufacturer burns almost completely, forming minimal volumes of ash;

• STIHL is the most famous brand manufacturer of garden technology. The lubricants of this brand have a balanced company composition, which contains all the required additives. STIHL HP oils can work properly during the operation of the saw at a temperature of up to.10⁰C;
• Partner-oils of this manufacturer of chainsaws are compatible with all 2-stroke power units. They are distinguished by increased lubricant properties, a high content of anti.Corrosion and anti.Intonate additives, as well as the ability to work stably at a temperature of up to.15⁰C.

When choosing oil for 2-stroke chainsaw engines, it is important to pay attention to its expiration date. The gardener should alert the manufacturer’s marks that the terms of the operation of its lubricant can be 3-5 years or more. After all, the additives contained in the oil have a tendency to evapon and loss of basic working properties

As a rule, well.Known brands are advised to use their lubricants for 6-12 months, since after this time the oil becomes unusable

After all, the additives contained in the oil have a tendency to evapon and loss of basic working properties. As a rule, well.Known brands are advised to use their lubricants for 6-12 months, since after this time the oil becomes unusable.

Storage of a chainsaw

A few words about conservation for the winter. Before sending a chainsaw to the shelf, it is worth performing the following actions:

One. Clean the chain and tire with a chain. 2. Drain the remaining fuel from the fuel tank. After that, start the engine until it itself is stalled.

Cool the engine (5-7 minutes). Then unscrew the candle and pour a small amount of oil for two.Stroke engines into the candle hole.

Pull the engine starting handle several times and install the candle in place.

Air filter should also be cleaned and drunk with oil.

STIHL HP Ultra Fully Synthetic 2. Cycle Engine Oil

Store the tool in a dry, ventilated room. Preferably at a temperature of at least 1 degree Celsius.

The ratio of oil and gasoline for chainsaws of well.Known brands, correct proportions, and also what should not be diluted

The preparation of the fuel mixture is a very important process, on compliance with the correct proportions of gasoline and oil, both gasoline consumption and the service life of the chainsaw. Many are used to interfering 1:50, but this is not right, t.To. The ratio of these two components, all manufacturers have different. Within the framework of the article, we will figure out what the most famous manufacturers are recommended, in what proportions, as well as give an example of how to dilute and cook fuel correctly.

Exclusively motor oil for two.Stroke engines is added to fuel for chainsaws. Oils for four.Stroke engines are categorically not suitable. The reason is that in two.Stroke ICE, the oil burns together with gasoline.

In car and other four.Stroke ICE, it is poured into the crankcase, has many special additives, it is not initially designed to combat. If it is poured into a chainsaw, it will smoke, will not burn out completely and quickly form a thick layer of carbon monoxide, which in the end can disable the chainsaw.

In addition to the general specification “for two.Stroke engines”, the manufacturer of the chainsaws may recommend using on their model oil of a particular brand. It can have special combustible additives and additives extending the service life of the ICE saw.

This is what oil for 2-stroke engines of chainsaws from the famous Champion brand looks like

In the old two.Stroke engines of the Soviet period, motor oil was also used, as in four.Stroke, for example M8. Old motor oils did not contain such a number of fireproof additives as modern. So that such non.Specialized oil provides sufficient lubrication of chainsaws, increased dosages were used.

When running the engine, 1:20 proportion was used, after 1:25. Large quantities of universal oil, not created under complete burnout, led to Rapid hair toxing and sticking piston rings, the formation of a carbon on the upper part of the piston, light of the ignition, in the exhaust Windows of the cylinder and a silencer. For the same reason, a spark on a chainsaw candle may disappear.

In advanced cases, Windows and muffler could be completely tightened by the car. The thick layer of the carbon on the piston significantly reduced the volume of the combustion chamber.

At the same time, the engine remains clean for a long time and serves for a long time, despite the lower supply of mechanical strength in modern ICE in comparison with the old.

We also recommend reading an interesting article about which oil to use for the chain of the chainsaw and how it can be painlessly replaced.

List of the best

And now, in fact, let’s get acquainted with the most optimal both in terms of quality and price category with oils that are widely used for the ribbon of the manufacturer Calm. And we will directly give them a small description, so:

This kind of oil is widely used directly for small.Sized four.Stroke engines. It can be used regardless of the time of year, but it must be remembered that the air temperature should not be lower than.15 ° C. Such oil is sold directly in bottles with a capacity of 0.6 liters and costs within 360 rubles.

Oil for two.Stroke engines 100 ml

This oil can be bought in a bottle that is one hundred milliliters for only 90 rubles. It needs to be added directly to gasoline. The ratio of their quantity should not exceed 1:50, that is, 20 g. Oil and one liter of gasoline.

Over, this kind of lubricant was developed specifically for the technique of the manufacturer. Its main component is minerals. But it can also be used in other models of other manufacturers. The main thing is that these chainsaws have a two.Stroke engine.

STIHL oil for two.Stroke engines 1l

The mass of the container in which the oil is sold is equal to one liter. It is intended directly for the ribs on the rosop, but is also perfectly used for tools of other manufacturers. Diluted directly with gasoline 1:50. And the basis of this oil is minerals. You will cost you this kind of assistant within 500 rubles.

STIHL oil for two.Stroke engines 1l. With a dispenser

Sold in a bottle, the capacity of which is one liter and which has a direct dispenser for three and five liters. Diluted with gasoline in a direct ratio equal to 1:50. Making oil specially for two.Stroke engineer engines of the manufacturer Calm. It was also made on the basis of mineral additives.

It is also widely used for models of tools of other manufacturers. The main thing is that these chainsaws have two.Stroke engines. It costs 600 rubles.

Is it possible to pour STIHL HP Ultra oil for two.Stroke engines 100ml

This kind of oil can be purchased in a bottle with a capacity of one hundred milliliters. It needs to be added directly to gasoline in a ratio of equal 1:50. Manufactured directly for the ribbon of the manufacturer Shtil.

It is a full synthetic oil, which directly has a high level of lubricant advantages. It can also be used directly for other models of chainsaws that have two.Stroke engines. Costs this kind of oil within 120 rubles.

Motor oil for a Shtihl saw for two.Stroke engines 5l

Sold directly in the canister, which has a volume of five liters. Designed for dilution with gasoline in a ratio of 1:50. Rospites with mineral additives and was created specifically for two.Stroke chainsaw engines. It is also widely used for lubrication of chainsaw engines of other manufacturers. The price category is 1,500 rubles.

STIHL HP Ultra chainsaw for two.Stroke engines 1l. With a dispenser

Oil is sold directly in a bottle, which has a peculiar dispenser for three and five liters. Designed to dilute with gasoline, the ratio of the number of these additives should not exceed 1:50.

How to use STIHL oil to lubricate the chain 1l

Sold in a bottle a container, which is one liter. It is an oil, on a synthetic basis, and which has a high level of lubricating characteristics. Over, with the help of this kind of oil, you can fully prevent the direct sample of the chain during its long operation (see. How to sharpen a chain). The price category is 215 rubles.

How the rupture “Shtil” refuels

In the technical passport of the tool, the manufacturer indicates how much fuel and lubricant should be used. According to the manufacturer, AI-95 gasoline is the best fuel for the STIHL chainsaw.

However, in domestic gasoline, to get the right octane number, various additives are added. As a result, its quality is reduced. Therefore, AI-92 gasoline is used as fuel for STIHL saw.

The type of oil depends on the engine power. For a two.Stroke engine, the original fluid “Shtil” is considered the best. It can be of two types:

What gasoline to fill in a chainsaw, the equipment manufacturer indicates. The mixture is usually prepared in a ratio of 1:50. In other words, 50 g of oil is required per liter of gasoline.

Useful recommendations

To ensure the longend work of the rupture “Shtil” it is necessary to adhere to certain rules:

Fuel should always be fresh. You can not fill gasoline from the canister, which has stood for more than a month. It is strictly forbidden to pour lubrices intended for four.Stroke engines in STIHL. The combustion of oil will be incomplete. Nar will begin to form, the piston group will quickly fail. For a two.Stroke engine, in which the combustion of lubrication should be complete, the manufacturer recommends the use of synthetic products. They form a minimum number of combustion products. When the mixture is divorced, it is desirable to increase the volume of oil

However, you need to do this carefully. 5 g per liter of gasoline is enough

If you add more, it is possible to form a carbon. A smaller volume of fluid, even 5 g, can cause overheating of the piston system. It is forbidden to fill a mixture cooked more than a month ago. You can not use lubricating liquids for mopeds. They are designed for a very small number of revolutions. When seasonal work is finished, the mixture must be drained or fully consumed. This is done to prevent wear of seals.

Choosing gasoline

The first question that the user faces before starting work is what gasoline to pour in a chainsaw.

Gasoline for a chainsaw of a calm is poured exclusively by.Ethyl high.Octane, t. E. With octane number above 90. If you refueled by low.Octane, this is fraught with an overheating of the engine, jamming the piston and output of the motor. Therefore, it is optimal to fill the gasoline of the AI-92 or AI-95 brand in the chainsaw, but the question of the quality of fuel arises here.

The poor-quality AI-92 may “not reach” to the declared octane number, and AI-95 often contains many additives that do not bring any benefit to the engine. In addition, if the additives are poor.Quality, they do not act long, and after a few days the acquired fuel can turn into a low.Octane, which is not suitable for the chainsaw engine.

At the same time, a good 95 can harm the piston system. To “burn” it. Thus, some users found a way out: to refuel a gasopyle of AI-92 gasoline mixed with AI-95. This is how the optimal balance between the octane number and the number of add.On impurities is achieved.

List of oils in terms of price and quality

Lubricants for 2-stroke engines:

• Volume 100 ml. You can buy it for 90 r., It is necessary to add 1 to 50 (20 grams of oil per liter of gasoline) to gasoline). This type is designed specifically for chainsaw. The main component is minerals. It is also possible to use for other models of various manufacturers.
• STIHL (volume 1l) intended for the saw of the manufacturer Shtil. Diluted 1 to 50. The basis of the lubricant is minerals. The price varies within 500 r.
• STIHL with a dispenser (volume 1l). Diluted in a ratio of 1 to 50. The price is about 600 r.
• STIHL h. P. Ultra (volume 100 ml), ratio 1 to 50. Also made for chainsaws. This is synthetic oil. It has a high degree of lubricant advantages. It is also used for other models of chainsaws with 2-stroke engines. The cost of this lubricant varies within 120 r.
• STIHL (volume 5l), the ratio of the product of lubrication to gasoline is 1 to 50. Component. Mineral additives. Created directly for chainsaws with a 2-stroke engine. Apply for others. The price is 1500 r.
• STIHL h. P. ULTRA with a dispenser (volume of 1l), diluted in a proportion of 1 to 50, made for the manufacturer’s chainsaw. Can be used for other brands. Cost 1100 p.

Gasoline and oil proportions for a trimmer calm

The German manufacturer of high.Quality cutting tools of calm, in addition to chainsaws, produces motor mowers. This is an indispensable tool for mowing grass and trimming the lawn, characterized by lightness and mobility.

Motokos, or trimmer, also has a two.Stroke engine and is seasoned with a fuel mixture. For the STIHL trimmer, 1:50 proportion is recommended (5 liters of gasoline 100 ml of oil).

What parts of the chainsaws need oil

If you look closely at the working chainsaw, then its main moving part is immediately striking. The saw chain, which glides along the tire during sawing. Since the law of friction still exists, both details gradually wear out. To slow down this process, it is customary to use a chain oil specially created for lubricating saw chains.

Chainsaws can be equipped with four.Stroke engines. As two.Stroke. In 4-stroke units, the lubrication of the crooked-shaped group occurs with oil in the crankcase of the engine. Two.Stroke engines are slightly different in their design and the principle of operation. Gasoline in this type of drive enters directly into the space under the piston, where there is a crooked-shaped mechanism that has several bearings and bushings that need lubricant. Therefore, oil for two.Stroke engines of chainsaws is added to gasoline so that it, falling on the rubbing parts of this block, lubricates them.

List of the best

And now, in fact, let’s get acquainted with the most optimal both in terms of quality and price category with oils that are widely used for the ribbon of the manufacturer Calm. And we will directly give them a small description, so:

This kind of oil is widely used directly for small.Sized four.Stroke engines. It can be used regardless of the time of year, but it must be remembered that the air temperature should not be lower than.15 ° C. Such oil is sold directly in bottles with a capacity of 0.6 liters and costs within 360 rubles.

This oil can be bought in a bottle that is one hundred milliliters for only 90 rubles. It needs to be added directly to gasoline. The ratio of their quantity should not exceed 1:50, that is, 20 g. Oil and one liter of gasoline.

Over, this kind of lubricant was developed specifically for the technique of the manufacturer. Its main component is minerals. But it can also be used in other models of other manufacturers. The main thing is that these chainsaws have a two.Stroke engine.

The mass of the container in which the oil is sold is equal to one liter. It is intended directly for the ribs on the rosop, but is also perfectly used for tools of other manufacturers. Diluted directly with gasoline 1:50. And the basis of this oil is minerals. You will cost you this kind of assistant within 500 rubles.

Sold in a bottle, the capacity of which is one liter and which has a direct dispenser for three and five liters. Diluted with gasoline in a direct ratio equal to 1:50. Making oil specially for two.Stroke engineer engines of the manufacturer Calm. It was also made on the basis of mineral additives.

It is also widely used for models of tools of other manufacturers. The main thing is that these chainsaws have two.Stroke engines. It costs 600 rubles.

Is it possible to pour STIHL HP Ultra oil for two.Stroke engines 100ml

This kind of oil can be purchased in a bottle with a capacity of one hundred milliliters. It needs to be added directly to gasoline in a ratio of equal 1:50. Manufactured directly for the ribbon of the manufacturer Shtil.

It is a full synthetic oil, which directly has a high level of lubricant advantages. It can also be used directly for other models of chainsaws that have two.Stroke engines. Costs this kind of oil within 120 rubles.

Motor oil for a Shtihl saw for two.Stroke engines 5l

Sold directly in the canister, which has a volume of five liters. Designed for dilution with gasoline in a ratio of 1:50. Rospites with mineral additives and was created specifically for two.Stroke chainsaw engines. It is also widely used for lubrication of chainsaw engines of other manufacturers. The price category is 1,500 rubles.

STIHL HP Ultra chainsaw for two.Stroke engines 1l. With a dispenser

Oil is sold directly in a bottle, which has a peculiar dispenser for three and five liters. Designed to dilute with gasoline, the ratio of the number of these additives should not exceed 1:50.

How to use STIHL oil to lubricate the chain 1l

Sold in a bottle a container, which is one liter. It is an oil, on a synthetic basis, and which has a high level of lubricating characteristics. Over, with the help of this kind of oil, you can fully prevent the direct sample of the chain during its long operation (see. How to sharpen a chain). The price category is 215 rubles.