When the air damper is closed, the trimmer stalls

Main reasons

Possible reasons for the lawn mower or trimmer to stall when trying to restart and resume interrupted work:

  • engine problems;
  • failure in the gasoline and oil supply system;
  • damage to pipelines (capillaries, hoses, nozzles);
  • faults in the ignition system.

A general description of scythe or trimmer problems is not enough here. A clear and immediate repair, high-quality service is impossible without specifying the identified cause.

Immediately after the start

The stalling of a lawn mower or trimmer immediately after the start is due to the following reasons:

  • imbalance of previously adjusted valves;
  • initially incorrect setting of the valve mechanism;
  • clogging of the fuel supply valve by deposits;
  • the hose is worn out or loosely connected.

How to Install a Forced-Air Bypass Damper | This Old House

Due to a broken fuel injection algorithm, the lawn mower or trimmer vibrates strongly during operation.

Diagnostic features

A well-posed question is already half the answer. The fact will significantly speed up the search for a solution. under what circumstances does a petrol trimmer or lawn mower stall, namely:

  • immediately after the start;
  • when it has been idling for some time. after one or several minutes;
  • when you press the gas button (or knob). or shortly after starting work at high, near-maximum speeds;
  • under heavy load (for example, to prune bushes, mow dense and tall weeds);
  • when warming up in the cold. it heats up unnecessarily (the lawn mower has stalled due to overheating);
  • after opening the air damper.

Depending on which of the circumstances was clarified during the pre-diagnosis, the elimination method looks for a more specific cause of the lawn mower or trimmer malfunction.

In the process of warming up the engine

If the engine heats up too quickly, overheats. the lawn mower or trimmer works unevenly, as if in jerks. After which it will stall. The reason may be as follows:

  • boiling gasoline;
  • the ignition wire is damaged (poor insulation);
  • the coil in the ignition system has noticeably burned out, interturn short circuits have appeared.

The same heating is observed when using a rotary (rather than a disc) damper.

damper, closed, trimmer, stalls

When the air damper is opened

The mower or trimmer stalls when the shutter is raised for the following reasons:

  • pumping excess air due to a cracked fuel suction hose;
  • oil seals are worn out;
  • improper functioning of the fuel and air metering unit when they are mixed.

Just Flight DC-8, Part 2 ( FSX )

In this case, the lawn mowers stop immediately.

When idling

When you run the trimmer or lawnmower at idle, you find that the device will start. but stall after, say, 5-10 minutes. The reasons may be as follows:

  • clogging, violation of carburetor adjustment;
  • initially incorrect setting of the carburetor valve mechanism;
  • clogging of the air filter;
  • reduction in the speed of the gearbox (if any). the wrong ratio of the air-fuel mixture;
  • clogging of the throttle;
  • the penetration of excess air into the fuel system;
  • running out of fuel in the tank (and oil in the tank if the engine is four-stroke).

If there are problems directly with the carburetor, the machine will stop both after a cold start and after starting on an already running engine.

When gassing

You press the gas. and the trimmer stops working, does not develop speed. Possible suspected causes are:

  • the carburetor setting is out of order, which appears with an increasing load on the drive itself. after its long idle time or when working in extreme conditions;
  • the fuel valve is clogged with deposits;
  • the carburetor cable is loose and sag;
  • the fuel supply hose is unnecessarily stretched, possibly torn;
  • the check valve (breather) is clogged with deposits. fuel does not flow into the fuel tank.

Important! Malfunctions in the carburetor itself give themselves away by vibration of the lawn mowers.

At high revs

When the scythe stalls at high speeds, this is due to the following problems:

  • clogging or sticking of the valve located on the gas tank cap;
  • the carburetor is out of alignment under the influence of vibrations arising from the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • suction of atmospheric air;
  • the fuel intake hose is cracked or loose.

Adjust the carburetor referring to the trimmer operating instructions. For adjustment, it is often enough to loosen the tightening of its housing. If there are problematic points with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its development, the engine stalls at high speeds.

Immediately after wound up

The unit may stall immediately after starting if the carburetor is misaligned or incorrectly adjusted. this causes an uneven fuel supply. The result is that the device vibrates distinctly. For troubleshooting, the carburetor is reconfigured, following the instructions for the mechanism.

Also, the engine stops when the fuel supply valve becomes clogged. In such cases, it is sufficient to simply clean it. If the mower started working at first, but then immediately stalled, then it is possible that the fuel enters the carburetor unit with some difficulty. The weakening of the valve helps to solve the issue, which ensures free circulation of the mixture in the system.

The stoppage can also be caused by air leaks in the presence of mechanical damage to the hose (holes, cracks) that takes the fuel. In this case, add more revolutions to the drive in order to quickly expel air bubbles from the system.

When heated

the lawn mower often stops when it heats up. At the same time, it starts up, works “jerky” and gradually stops. This process occurs when the gasoline in the carburetor boils or the damper is installed in a rotary rather than disc type. In the latter case, the part is changed.

It happens that the trimmer heats up if the ignition circuit wire or coil is damaged. In order for the device to start working normally, replace parts.

What could have broken

Problems with the lawn mower due to the fact that this device does not start are classified in a certain way by service specialists. They highlight faults with the following components of the mechanism:

  • an engine in which the piston and bearings may wear out or fail, crack the crankcase;
  • the fuel supply system, while the filter may be clogged or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • ignition circuit.

To correctly determine the node where the breakdown occurred, you need to pay attention to the circumstances under which the trimmer stalls.

Idle

At idle, common reasons for stopping the trimmer are as follows:

  • contamination, misalignment or incorrectly adjusted carburetor adjustment;
  • clogged air filter;

Replacing the air filter for lawn mowers

Trimmer air filter

  • reducing the speed of the gearbox when it heats up, which is a consequence of the use of an unsuitable fuel mixture;
  • clogged throttle;
  • air ingress into the system;
  • not enough fuel to operate the lawn mowers.

If the problem area is the carburetor, then the equipment will stop at both “cold” and “hot” start.

When you hit the gas

If the lawn mower stops when the throttle is pressed, the reasons may be as follows:.

  • The most common option is carburetor adjustment failure, which occurs when the drive is under heavy load, after prolonged inactivity of the mechanism, or when it is used in difficult conditions.
  • Clogging of the fuel valve, which is eliminated by loosening it, as a result of which gasoline begins to flow normally through the system.
  • Loosening and drooping of the cable in the carburetor. The fuel hose may also be stretched to the point of rupture due to significant stress.
  • Clogged breather (check valve), as a result of which fuel does not enter the tank.

If the problem is with the carburetor assembly, the lawn mower vibrates to recognize it. When the hose bursts or the cable is stretched, these components are replaced.

Why does the petrol trimmer stall

A scythe with a gasoline drive is a useful thing for owners of home gardens, lawns, and when the trimmer suddenly stalls, the work to clear the area from grass stops. The device itself is a rather complex mechanism, so there are many different reasons for its breakdown. The most common malfunctions are contained in the operating instructions. You should know the reasons why the trimmer stalls in order to effectively repair the device yourself.

The chainsaw stalls at high speeds. simple carburetor repair

The carburetor of the instrument is exactly the mechanism that most owners are afraid to disassemble on their own. The reason is that this mechanism consists of many small parts, the location of which must be remembered when carrying out dismantling work. However, not everything is as scary and difficult as it might seem. To understand how the carburetor has to do with the problem of stopping the engine when the engine speed increases, you need to find out its principle of operation, described on the website.

The chainsaw stalls when you press the gas due to the carburetor, if:

  • Diaphragm damaged
  • Clogged filter element (mesh in the carburetor). This malfunction can be encountered by owners of tools who do not have a fuel filter or it is simply disconnected from the fuel hose.
  • Needle sticking, which may be due to the use of an outdated fuel mixture
  • Clogged nozzles or clogged carburetor
  • Bending of the connecting part connecting the membrane with the needle to supply fuel to the fuel chamber of the carburetor. This part is also called a foot, since under the influence of the membrane on it, the needle moves and the channel opens. During operation, this foot can bend (work out) or break (the engine will not start if it breaks). If the foot is bent, then it can be unbent, but this does not guarantee that the problem will soon recur, therefore it is recommended to replace the part

It is recommended to clean and wash the chainsaw carburetor, as well as replace defective parts and elements. After that, you can put it back, not forgetting to also replace (if worn out) the gasket between the carburetor and the adapter.

What to do if the chainsaw stalls when you press the gas

Despite the high performance of chainsaws, sometimes there are times when the tool stops working normally. In particular, a common situation is the fact that the chainsaw starts to stall when you press the gas. For experienced owners of tools, this problem is known, but beginners who are faced with this for the first time will have to seek help from specialists. But do not rush, in the material you can find all the important causes of the malfunction, as well as try to eliminate them.

Stalls under load

If the chainsaw starts to stall under load, then the reason for this is, first of all, an incorrect carburetor setting. If this reason is eliminated, then in addition to problems with the carburetor, the reason for the inoperability of the tool under load may be damage and wear of the crankshaft oil seals or carburetor gaskets, through which air is sucked into the system.

It is recommended to start troubleshooting by checking the oil seals and gaskets, and only after that check the correctness of the carburetor setting. Another reason why the chainsaw starts up and immediately stalls under load may be the chafing of special hoses, through which the impulse is transmitted from the crankcase to the fuel pump. But such hoses are not installed on all models of chainsaws, but only mainly on professional ones. It is recommended that this hose be replaced to rectify the problem. How to do it correctly is discussed in the video:

When heated

the lawn mower often stops when it heats up. At the same time, it starts up, works “jerky” and gradually stops. This process occurs when the gasoline in the carburetor boils or the damper is installed in a rotary rather than disc type. In the latter case, the part is changed.

It happens that the trimmer heats up if the ignition circuit wire or coil is damaged. In order for the device to start working normally, replace parts.

Adjusting the carburetor when the engine stalls when accelerating

If the check showed that the fuel supply system, muffler and spark plug are in good working order, then you need to look for a breakdown in other places. Initially, do not rush to disassemble the cylinder-piston group or change the carburetor. It is recommended to start repairs by adjusting the carburetor. For this, all chainsaws have special adjusting screws. They are designed to adjust the idle speed, as well as adjust the fuel supply at low and high speeds. A detailed description of how to adjust the carburetor of a chainsaw is described on the website.

Today we will consider the features of setting the carburetor at maximum speed. You can make sure that the chainsaw is not developing full power using a tachometer. If there is no device, then you can make sure that the engine does not develop maximum speed by ear. We are interested in the screw on the carburetor. Which is for setting high rpm. It is usually denoted by the Latin letter “H”, which is abbreviated from the word “High” (high or large).

To adjust the high speed of the chainsaw, you will need to perform the following manipulations:

  • Tighten screw H clockwise until it stops.
  • Next, you need to loosen it by 1.25-1.5 turns
  • Run the tool and test the speed performance

It is recommended to adjust the tachometer, but if it is not there, then you can check the maximum speed when the tool is working under load.

It is interesting! If you often work with a chainsaw, then you will need to purchase a tachometer, since it allows you to set the most efficient engine operation, which affects fuel consumption and unit power.

After the trivial setting of the carburetor, you can fix the problem with the termination of the engine when the speed rises. It should be noted that it is necessary to adjust the carburetor of the chainsaw regularly, depending on the frequency of operation of the tool. It is not difficult to do this on your own, but you can achieve accurate tuning in one case. if you use a tachometer.

The chainsaw engine stalls when you press the gas

The chainsaw is a highly efficient tool for working with wood. However, the high-speed motor of this tool can be used for a variety of other tasks, which is achieved through special attachments. Sometimes a malfunction such as the chainsaw stalls when you press the gas, which can be triggered by some factors. In order not to have to disassemble the tool completely, we will consider all sorts of reasons for this problem with a detailed description of how to fix them.

Idle

At idle, common reasons for stopping the trimmer are as follows:

  • contamination, misalignment or incorrectly adjusted carburetor adjustment;
  • clogged air filter;

Replacing the air filter for lawn mowers

Trimmer air filter

  • reducing the speed of the gearbox when it heats up, which is a consequence of the use of an unsuitable fuel mixture;
  • clogged throttle;
  • air ingress into the system;
  • not enough fuel to operate the lawn mowers.

If the problem area is the carburetor, then the equipment will stop at both “cold” and “hot” start.

At high revs

When the scythe stalls at high speeds, this is due to the following problems:

  • clogging or sticking of the valve located on the gas tank cap;
  • the carburetor is out of alignment under the influence of vibrations arising from the operation of the mechanism;
  • problems with the circulation of the fuel mixture;
  • suction of atmospheric air;
  • the fuel intake hose is cracked or loose.

Adjust the carburetor referring to the trimmer operating instructions. For adjustment, it is often enough to loosen the tightening of its housing. If there are problematic points with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its development, the engine stalls at high speeds.

damper, closed, trimmer, stalls