Which Is Better Makita Or Bosch

BOSCH or MAKITA: which screwdrivers are better?

Bosch and Makita are world leaders in the production of household and professional tools. Over, the German company also produces kits

Dimensions and weight

The models of the German concern are slightly lighter and smaller due to the features of the gearbox. Similar Japanese models weigh 1.8 kg versus 1.7 kg of the German concern. The greater weight of Asian models is reflected in the duration of the tool. And the large size will interfere with work in hard-to-reach places.

Batteries

Both companies use similar lithium-ion batteries in their screwdrivers. 24V devices are used only by professionals. In the middle price segment, the battery voltage is reduced and without load is 18V with a capacity of 1.5 Ah. Bosch torque is 2030% higher than competitor’s due to gearbox features. Thus, large fasteners are tightened much easier and tightening them at low speeds is easier. The battery of the German holds a little longer, even taking into account the higher torque and is equipped with a charge indicator. When removing the Bosch battery, it is taken out to the side of the hand holding it, which is inconvenient.

Equipment

Models of both brands are sold completely ready-to-use and are equipped with approximately the same:

• Plastic case;
• Charging station;
• A pair of batteries.

Some Makita models come with a flashlight and a reversible bat. Both mid-range brands are equipped with illuminated work areas. The German case is equipped with compartments for storing documentation, bits, and accessories, but it is inferior in strength to the Japanese one.

Cartridges

The chuck of the Japanese manufacturer sits better on the shaft and does not dangle, the bit is clamped more reliably and without any gap. Unlike the German brand, the cartridge is more precisely centered, balanced and the runout is imperceptible. Keyless chuck up to 13 mm diameter allows one-handed tool change. The hammer drill mode will help you work with tough materials. A hole diameter of 13 mm expands the scope of the tool.

Only a 10 mm drill can be inserted into the German’s chuck. But the density of the jaws’ compression will allow the use of the thinnest rigging without adapters.

BOSCH or MAKITA: which screwdrivers are better?

Bosch and Makita are world leaders in the production of household and professional tools. Over, the German company also produces kits for turbines, auto parts and household appliances. The Japanese are highly specialized in tools and machine tools. The toolkit of these companies is considered a model of reliability and practicality. Which one to give preference when buying a screwdriver? In the article, we will compare average price household devices.

Bosch manufactures household and professional equipment lines. They differ in colors green for the home and blue for professional activities. Makita is no longer engaged in the production of a household series, completely abandoning it in favor of a professional one. Previously, the Maktes brand produced models with a simple structure and weakened materials.

In the production of new models, Bosch first runs them in the household series, then includes them in the Bosch Professional line. Thus, the tool undergoes a two-stage reworking and running-in. Makita 20 years ago was ahead of the development of the German company. Now production has been moved to Asian countries, which affected the quality of manufacturing and assembly. Consider the models of devices that are similar in price and characteristics.

Button quality

The buttons of Bosch products are massive, pleasant to switch. Their course is smooth without backlash. Are fixed clearly. The ergonomics of their design allows you to use the tool with great comfort. The rattling buttons of the Asian brand are more reminiscent of the Chinese manufacturer and do not correspond to the quality of the brand.

Makita about the brand and benefits

The Japanese brand Makita is known not only for quality technology, but also for constant innovation. There is no better technology in the world today than Japanese ones. The bright red Makita logo on the grinder indicates that the unit will function perfectly and will clearly provide comfortable operation. Japanese materials are known to be of high quality, factory assembly, strictly controlled. The service life is long, and the reliability has been proven by many decades of operation of Japanese devices, including angle grinders.

The assortment should be noted separately. Although we said at the beginning of the article which grinder is more suitable for the home, the brand’s catalog contains models for both domestic use and complex professional tasks. For household work, they are taken more for the simple reason that most angle grinders are compact in size, light in weight, and low in noise. And with a light and quiet machine, you can work for a long time and not get tired.

Among Makita grinders you can choose:

• Powerful networked machines for cutting metal, for grinding various surfaces. They are relevant for work indoors, or close to home. The power is excellent, but there is a network cable tie to the outlet.
• Small battery models. They are good because they are always ready to work anywhere, you just need to monitor the battery charge.

By design, one-handed grinders and two-handed angle grinders are presented.

A very generous arsenal of electronic functions is also pleasing:

• Adjustment of the spindle rotation speed, depending on what material is being processed;
• Smooth start (no jerk at the start);
• Support of constant speed (the engine does not stall under load).

Japanese grinders are safe to work because they are equipped with:

• Anti-jamming protection;
• Lock button against accidental activation;
• Spindle blocking when changing an accessory.

The more electronic lotions in the device, the higher its price, but it is a pleasure to work with such a grinder. But, to the credit of Makita, it should be noted that even the cheapest of their models are very ergonomic, with well-thought-out algorithms for protecting against injuries, and very functional.

Which grinder is better: Bosch or Makita

The grinder, as a cutting and grinding tool, is relevant for any repair, both home and professional. The device is universal, it all depends on which power grinder to use, and which attachment to install on it. They buy it not for one-time use, but for many years of service. In order not to get into a mess when choosing and not to get a cheap toy that breaks after several times of use, special attention should be paid to the manufacturer.

Today in Ukraine the most popular manufacturers of grinders are Bosch and Makita. Their tools are durable, practical to work with. Both companies are actively working to improve their technology. Thanks to the introduction of various technical innovations, the buyer receives not only a reliable angle grinder for work, but also excellent additional functions.

Which angle grinder is better, Bosch or Makita, is an ambiguous question, because both of these brands are winners of all kinds of ratings and trendsetters in the Ukrainian technology market. In short, for long-term loads and professional work, we recommend Bosch grinders, and for home use you cannot find a better machine than a small and functional Japanese Makita. Buying a Makita grinder means getting an excellent assistant both for home and for professional repairs and construction projects.

Than one another better compare similar models

For a detailed comparison, let’s take the most popular models from both manufacturers with similar technical characteristics:

1. Angle grinder Makita GA9020SF with a mains motor power of 2.2 kW and an admissible disc diameter of 230 mm.
2. Bosch GWS 22-230 JH angle grinder with the same output of 2.2 kW and the same outer disc diameter of 230 mm.

As you can see, the power of the drives is the same, which makes it possible to saw and grind with large wheels with a diameter of 230. Bosch and Makita cost the same, the price is the same, about 3.5 thousand UAH.

What do we get for such a cost:

• Reliable brushed motor with excellent power, Makita has more revving 6600 rpm;
• Robust dustproof housing;
• Adjustable protective cover;
• Reliable fastening with a turnkey clamping nut;
• Two handles front, which can be installed and fixed in three positions, and the back without adjustment;
• Three-year manufacturer’s warranty;
• Automatic shutdown when the disk is jammed.

As for the set of electronic additional functions, both grinders have a soft start and speed control (spindle speed).

The German manufacturer took care of safety and ruled out unintentional re-switching, the Bosch grinder has a lock button. But the Japanese angle grinder includes another very important function of maintaining constant engine speed. This means that the motor torque does not drop even when the unit is used at maximum load. Simply put, such a grinder will not stall, the revolutions will not fall, the power will not decrease, which is very important when cutting thick metal, with rough grinding.

When comparing the weight, it is clear that the Makita grinder is a little heavier, but it clearly wins in terms of comfort during work. She has an anti-vibration system installed. As a result, we get:

• Less vibration during stripping (2.5 versus 3.5 for Bosch) and when sanding (6 versus 7.5 for Bosch);
• Lower sound pressure level.

BOSCH grinders that meet European standards 100%

Bosch is a renowned German manufacturer. It is one of those companies that introduced the so-called excellent German quality technology to the world. Bosch grinders are fully consistent with the world idea of ​​the meticulousness and scrupulousness of the Germans, their assembly is ideal, everything is taken into account to the smallest wiring and screw, everything works and is designed for a long service life.

Among the developments there are expensive models that allow you to perform work with the highest comfort and very high quality. There are also budget grinders, with a smaller set of additional functions, for example, without a speed controller. Such a machine works only at one maximum rotation speed, but all its other indicators (power, durability) are at the highest level. It turns out that you can save money and buy an excellent professional device with good technical characteristics for a low price. Over, the inconvenience from the lack of a speed regulator arises only when grinding or when cutting very thin sheets of metal. And you can install it yourself.

The main advantages of Bosch grinders:

1. A varied price range is how to choose both very expensive and very cheap practical models, without electronic bells and whistles;
2. High quality materials and workmanship that meets European standards;
3. Effective security systems and protection mechanisms;
4. The functionality and power of solid professional tools.

Conclusions

As you can see, at a similar price, there is not much difference between professional grinders from Bosch and Makita. Is that the Japanese engine is more resourceful, and, moreover, these rpm do not drop under increased loads. This function will allow you not to worry, giving a load to the motor. Also, the Japanese angle grinder makes much less noise and vibrates, so you can work with it for a long time, while the user is less stressed and less tired.

Categories hunted by masters

In fact, in order to get a positive rating, a tool must have only a few categories:

• Affordable price;
• High resource;
• Maintainability;
• Ergonomics.

According to the first indicator, Makita wins unambiguously. With regard to the resource, everything is not so simple. The fact is that Bosch has two lines of tools for household and professional (yellow and blue).

It is she who sells household tools. It turns out that manufacturers are equal in this category.

As any professional repairer will tell you, most Bosch equipment is more complex in design. But it also provides a little more functionality. In comparison, the Makita is simpler. However, this simplicity and provides a huge resource, the tool simply does not break.

Makita or Bosch which is better?

There is a dilemma when choosing a hand tool today. By and large, there are two leaders on the market who do not want to concede an inch to each other. We are talking about such venerable manufacturers as Makita and Bosch. On specialized forums, disputes constantly flare up, which result in intense discussions. Someone assures that there are no better tools than Makita. Others claim Bosch’s reliability and ergonomics. Whose side is the truth on?

An authorized Makita dealer is able to provide a wide range of equipment on favorable terms. Bosch prices are slightly higher. This is understandable, because most of the technical innovations that are used by many brands in hand tools were first applied in Bosch.

Continuity is very important

Regardless of whether a professional tool or a household one, if long-term work is required, the master must be able to perform it. This indicator largely depends on the ergonomics of the instrument.

Any tool (unless it is pneumatic) has a very significant weight. And if, for example, it is necessary to perform work under the ceiling, holding the tool at half-outstretched hands, you get tired very quickly.

But due to the use of special handles, the tool can be taken differently. As a result, hand fatigue builds up much more slowly. In terms of ergonomics, both brands are also equal. So it turns out that with a minimal advantage Makita wins.

An experienced craftsman will deliver his verdict in an ongoing dispute between Bosch and Makita adepts:

Comparison of drills Bosch and Makita or which one is better to choose

Author: Sergey Khilik

Expert category: “Hand and power tools”

A hammer drill is good when it is convenient to use, performs several functions (moreover, with the same efficiency) and serves for a long time, without breakdowns and repairs.

Since today no construction site or even minor repairs can do without a perforator, the issue of its choice is very relevant. With this device (mains or battery), you can drill, and make holes in the surface, and easily dismantle a wall or other types of partitions. In this device, as a rule, there are several modes. Functions are switched by pressing a special button located on the handle. Choosing the desired mode, you can carry out drilling, drilling using an impact mechanism, the impact itself (such as a jackhammer).

When choosing a perforator, it is necessary to take into account its performance indicators: power, impact force, pay attention to the design and power supply of the drive.

However, in this article I emphasize that there is one more important characteristic of any unit of technology. It is quality. I mean, both the build quality and the materials used. It depends on them how long the tool can work, how quickly you take it to the service or (in case of an unscrupulous manufacturer). To the landfill.

After reading the article, you will understand why you need to pay attention to quality and brand. Indeed, in order for the perforator to serve for a long time, you need to choose models from a trusted manufacturer.

In this article, I will inform you about the quality and performance of two of the most sought-after brands of rock drills. These are German Bosch and Japanese Makita. Their models are in great demand among the population and business.

Design features of Bosch and Makita rotary hammers

The design of each rock drill includes the following details:

• Motor (stator and armature);
• Gearbox (barrel, pneumatic piston, rolling bearing and a set of springs and couplings);
• Electrical cable;
• Carbon brushes;
• Power button.

1. Makita has taken care of the convenience of technology. Rubberized handle, so you can work without special gloves, because the tool does not slip out of your hands;
2. Also, Japanese technology has a special rubber pad on the gear part. You say. It is a decorative element. Not. It is, first of all, taking care of the instrument. Namely. It is needed so that when working in narrow places or in an uncomfortable plane, the plastic case is very strongly wiped off the puncher, which leads to further deformation, cracks and breakages;
3. If you noticed, HR2470 has a rubberized protrusion near the mode switch knob, which is the most ingenious and simple solution to protect the switch itself, since working near the wall can accidentally move the knob and disrupt the operation;
4. But the German manufacturer decided to distinguish himself as follows. The cable at the entrance to the handle has a special hinge, therefore, in whatever planes the machine is working, the cable in this place has a minimal chance of refraction, and in fact almost all instrumental equipment suffers from this “disease”;
5. Although the Bosch handle is not rubberized, the drilling depth limiter has a separate locking button. This helps to quickly set the length you need without unscrewing the handle of the tool itself;
6. The reverse switch is not completely covered with plastic (like Makita’s), this allows you to clean and blow out the brush assembly without removing the back of the handle, which is also convenient when there is a lot of work, but it must be done quickly.

Comparison of drills from Bosch and Makita. This is the same time-consuming task as comparing Audi and Toyota or Mercedes and Lexus, because the range of tools from both manufacturers is very wide and the number of technical solutions, know-how, their design and equipment will suit the work of any professional builder. The matter is small. Choose the option you like.

Bosch and Makita rotary hammers warranty

The number of service centers that serve both brands is also sufficient throughout the country, so there are no special problems with fast and high-quality repairs.

And some information about the cost of spare parts. Makita in this regard is partly cheaper, since original spare parts for the tool are produced at a factory in China.

The difference in quality

Comparing a professional quality tool is as difficult as the German and Japanese car industry. The German instrument is distinguished by the fact that it has a consistent shape, angular design and, say, controversial elements of convenience. The Japanese are opposite. Have more soft lines, a streamlined shape and some useful little things. Above, I already wrote that Bosch is popular because most rotary hammers proudly say “Made in Germany”, and this today very much attracts customers, because everyone appreciates European quality, and especially if it is also assembled in Germany. Makita is the opposite. On punchers of small models, you can find on the nameplate the mysterious three letters PRC, which stands for Peoples Republic of China (in folk. China). This, for some reason, scares our person away from the acquisition. Although I note that Makita opened a plant in China in 1986 and it was the second to be built after the main office.

Today, the main competitors on the market, like many years ago, are two models: Bosch GBH 2-24 DRE and Makita HR2470.

The Bosch hammer drill has the following technical characteristics:

• Works with a power of 790 W;
• The impact mechanism hits the material with an impact force of 2.7 Joules;
• In rotation mode, the tool makes 4200 rpm;
• Equipment SDS plus;
• Drilling diameter in concrete. 24 mm, metal. 13 mm, in wood 30 mm; working crown 60 mm;
• Price 3999 UAH

As for the hammer drill from the manufacturer Makita brand HR2470, it belongs to professional tools and has the following characteristics:

• Power 780 W;
• In rotation mode, it makes 1100 revolutions per minute;
• The impact mechanism makes 4050 strokes per minute and hits the material with a force of 2.7 Joules;
• Concrete will be drilled with a diameter of 24 mm, metal. 13 mm, wood. 32 mm;
• Price UAH 4099

A little about Bosch

Bosch is a German company. The firm was founded in 1886. Rotary hammers from this manufacturer occupy one of the most important places in the professional power tool market. The company specializes in creating tools for both small household repairs, where the models come mainly with the SDS-Plus chuck, and for work on large construction sites, where the company presents a wide range of tools with models with all popular SDS-Plus, SDS- Max, SDS-TOP HEX.

Why are Bosch tools so good? This is really proven German quality over the years, and on most models you can find the inscription “Made in Germany”, which everyone loves. But since today the company is so wide and has over 200 of its own factories around the world, the equipment can be produced in other countries, for example, the household line (green) can be assembled in Hungary, China and Russia.

Makita brand. Real japanese build

Makita is a Japanese brand that specializes in the production of gasoline and electric tools for the home and professional use. The company was founded in 1915. At the beginning of its activity, the creators of the brand specialized exclusively in the repair and sale of lighting equipment. For the first time its own products under the Makita brand entered the market in the twenties of the last century.

Brand overview

Bosch

Bosch (or rather, Robert Bosch GmbH) is a group of German companies that specializes in the production of high-tech equipment in various fields. The company was founded in 1886 and initially focused on electrical engineering and precision mechanics. It is not surprising that starting in the 1890s (the start of electrification in Germany), Bosch’s business began to develop rapidly, occupying new market niches, including those related to the design and production of power tools.

The presence of its own engineering department in the company has served well in the expansion in the market of household and professional tools. It was under the Bosch brand that such devices as a jigsaw, a rotary hammer, a variable grinder, a cordless rotary hammer, etc. Were first released. This also includes the SDS-Plus perforating drill attachment system, it was developed and first introduced by German engineers.

In general, Bosch power tools fully comply with our ideas about German quality standards, they are reliable and durable, therefore the purchase should be considered as a fairly long-term investment.

Makita

Makita Corporation (Japan) was founded somewhat later in 1915, and initially focused on the manufacture of generators and electric motors. In 1958, the first line for the production of power tools was launched: the first electric planer was released under the Makita brand, which at that time had no analogues.

Today the company produces more than 1000 brands of tools of 350 different types. Technological capacities are partially moved outside Japan and are located in Great Britain, Romania and Germany.

Comparison by key parameters

Professional and household lines

For a correct comparison between Bosch and Makita, it is worthwhile to figure out which lines of tools these corporations produce.

• Blue series professional equipment. Actually, this is the very Bosch, which is characterized by high power, long service life and safety margin.
• Green series power tools for household use. Due to limitations in power and functionality, as well as the use of less durable materials, the manufacturer seriously reduces the cost of products. But their safety margin also suffers, in any case, in comparison with the professional line.

Sometimes models are released in the green series, which they then plan to bring to the professional market. Therefore, the household segment often serves as a testing ground for new products.

• It produces only professional tools under its own brand, so it should be compared only with the blue Bosch series. The performance parameters of the products are at the highest level, so that there are almost no significant claims from the craftsmen.
• In the 90s, Makita Corporation attempted to launch a line of household power tools under the Maktec brand. The products turned out to be cheaper, but they were significantly inferior to their professional counterparts in terms of power and reliability.

Cost and other factors

• Power. In principle, it is equivalent for both brands (at the same level of energy consumption). In rare cases, Bosch outperforms the Makita in certain parameters (for example, efficiency on concrete).
• Ergonomics. The Makita is in a better position here, primarily because of the lighter tool mass. With long-term work, this plus becomes quite significant.
• Resource. Bosch with its German quality is noticeably better. Despite the fact that Makita has good control over production in different countries, the overall level of reliability of the tools is still somewhat lower.
• Functionality. This parameter can be assessed in two ways: Bosch is the first to have new functions, Makita brings them to mind perfectly, but with a significant time delay.
• Prices. Bosch costs a little more on average (if we talk about tools of a comparable class). On the other hand, the difference is usually not so significant, and it can be compensated by finding a retail outlet with a more democratic pricing policy.

Which is better: Bosch or Makita?

In any environment, professionals often get into arguments about which brand is better. For graphs, this is, of course, the eternal confrontation between Nikon and Canon, for owners of Apple smartphones with its iOS and Samsung with Android, etc.

Builders and finishers also do not stand aside, and quite often they discuss the advantages and disadvantages of certain brands of tools. But if you compare, then compare the best representatives, so we turn to the results of the survey on the site. As of May 2017, in a survey of their preferred brand of construction tools, 31% of users voted for Makita and 23% for Bosch. So we will choose the leader from these two brands and try to decide which is better than Bosch or Makita.

Instead of a conclusion

To answer unequivocally the question What is better than Bosch or Makita, probably, will not work: both brands produce sufficiently high-quality, reliable and functional tools, which rightfully occupy a leading position in this market segment. So, when choosing between Bosch and Makita, we choose not between good and bad, but between good, also good, but slightly different.

Features of the Bosch brand:

Germany. The assembly is usually Malaysian;

Basically three years warranty (one year in Makits);

Better performance characteristics and, as a consequence, more weight.

Rotary hammer Bosch or Makita, which is better?

In this market segment, you can compare the BOSCH 2-24D and Makita HR2470 models.

Maximum drilling diameter (mm)

Rotation speed (max rpm)

As you can see from the table, the difference between the models is very small. However, for the sake of fairness, it should be noted that the chiseling function is better developed in BOSCH 2-24D. In contrast, we can say that the Makita HR2470 is equipped with special carbon readouts that increase the service life, and this model is also lighter and faster. What is more important for professional use, since it is important during long-term work and will save money in the future. Hence, in this example between bosch or makita, the last brand wins.

Grinder Bosch or Makita, which is better?

Moving on to the next pair, this time let’s compare the Bosch GWS 850CE and the Makita GA5030.

Bosch GWS 850CE

Disc size (max, mm)

In this comparison, the GWS 850CE looks like a clear leader due to the higher power, but there are many complaints about it. In particular, on a switch that is too hard, as well as on the factory lubrication of the gearbox. The latter applies only to the Russian assembly. In addition, professionals blame the lack of a complete set of this model.

Relative to the Makita GA5030 model, it has a clear advantage of its low weight, which is explained by the small size of the tool. Thanks to this, the hands do not get so much tired. Otherwise, these grinders are almost identical in terms of performance and functionality. Therefore, choosing only between them, it is difficult to point out the unequivocal advantage of this or that model. However, if we take the approach, then the choice again tends in favor of Makita, due to the primacy of simplicity and convenience over purely technical characteristics.

Makita or Bosch screwdriver, which is better?

When comparing screwdrivers of these brands, perhaps you should not resort to the previously selected method, because if you compare, then you need tools that are close to each other. And in this case, they are difficult to find, except for the Bosch GSR 10.8-2-Li and Makita DF330DWLE models. But these are old-style instruments and their technical characteristics are already outdated. Therefore, comparing screwdrivers, it will be better to summarize the pros and cons of Bosch or Makita.

Which is better Bosch or Makita: specific examples

The modern market for construction power tools offers a very large selection, both in terms of the brands presented and in terms of specific models. But which brand is better, only experienced professionals know. And this is a big problem, a beginner who made the wrong choice can lose not only his money, but also something much more. Since poor-quality construction or repair work in some cases leads not only to injuries and financial losses, but also to death. And to prevent this from happening, the tool used in such robots must be of the best quality.

Between two

For example, you can compare Bosch and Makita by the brands of rotary hammers, grinders and screwdrivers they sell.

Makita Brand Features:

Japan. The assembly is usually Chinese;

Affordable prices (compared to Bosch).

As you can see, the difference between brands in their approach. For Bosch, this is German precision, reliability and power. Makita is characterized by convenience, economy in terms of price and excellent equipment. In other words, the former are guided by the tool itself, and the latter by whoever will use it. That allows you to give a clear answer to who is better. Namely:

If a tool is needed for a beginner and not for frequent use, then Makita should be chosen.

While professional builders are better off choosing Bosch, the 3 year warranty and reliability are more important when using power tools permanently.

Which is better: a Bosch or Makita jigsaw?

The choice of jigsaws of these two brands in general comes down to the choice between the manufacturers themselves. We will talk about their features below. Well, and some practical material based on Bosch PST 800 PEL and Makita 4327.

Features of Bosch and Makita

The characteristics of these brands as a whole will be considered in the context of the range of products provided, its level (household or professional) and the use of new developments (innovation).

1. Range of products.

If Bosch is the largest corporation that internationally produces a wide range of products (power tools, household appliances, auto parts and turbine components), then Makita has a narrower specialization. The Japanese corporation is focused on the production of tools, machine tools and equipment. With regard to the range of power tools, it is equally wide and varied at both Bosch and Makita. Makita is four times ahead of Bosch in jackhammers alone (20 models), while Bosch remains the leader in tooling production.

1. Household or professional?

Only Bosch has the distinction between domestic and professional tools. Positioning the same Makita manufacturer of professional power tools. Bosch household tools are also called (according to the color of the equipment produced) green series, and professional blue series. Given the limited functionality of household power tools, it makes sense to compare only the professional Bosch and the professional Makita.

In the 90s, Makita launched a household power tool line, but under the Maktech brand. In this case, the best developments of the models of the parent brand were used, but the devices were supplied with a simplified design and from cheap materials. Thus, the main advantages were retained along with lower costs for the end user.

1. Innovative technologies and product quality.

The only obvious advantage of Bosch over Makita is the introduction of new technologies due to the presence of a good research base. A prime example of this is the SDS-plus chuck, which incorporates a system for securing rock drills.

Actively participating in the development and implementation of new technologies, Bosch successfully uses its range of household power tools in order to test their new products, and only then launch them into serial production on a professional tool. The benefits for residential and professional users are obvious: the former get advanced solutions for a price that is quite elevated for the home user, the latter pay a decent price for functionality that has already passed field tests and will not fail at the most inopportune moment.

So, choosing between Bosch and Makita in general is a matter of taste. After all, both there and there are quite decent quality. It will be more important to pay attention to a specific model of a specific instrument. We will do this on the basis of the Makita 4327 and Bosch PST 800 PEL jigsaws.