Why does a trimmer spend a lot of gasoline. Gasoline consumption rate for a lawn mower

Why does a trimmer spend a lot of gasoline

The lawn mower. A very ordinary device. There is nothing special in it. And therefore, many acquire it for their own needs, since everyone will be able to master how to work with it, and everyone will be able to quickly.

One who has bet on gasoline trimmer, Must know that for him one of the important features is fuel consumption. And there is a common explanation. At first, the device should make its functions for a long time so that for a long time there is no need to do refueling. It is always comfortable.

Large fuel consumption with a benzocosa, a trimer, increased revolutions, one of the reasons.

Fundamentally! But in this case, of course, the fuel tank will be a huge volume. As a result, in general, its design becomes heavy. And this will make it difficult to work. Is it possible to find a wisest solution in this situation? You can solve the case by reducing fuel consumption.

Then we will talk about how it can be, what the fuel trimmer consumption depends on, we will also advise which gasoline is better to choose for work.

The spring may interfere

My first attempt to adjust the carburetor of the benzokos did not give anything, since the spring of the fuel mixture adjustment propeller prevented. The factory spring turned out to be too thick in a compressed state and did not make it possible to reduce the supply of fuel to the required level. I had to choose another spring and continue the adjustment after its replacement.

The adjusting screw for feeding the fuel mixture with the spring

In the photo above the factory spring, below the adjusting screw with a selected spring. I am writing about this, because I am not sure that this is an isolated case, and someone else may face the same situation.

Gasoline consumption rates for trimmers

Say, the Husqvarna 122C device, which has a two.Stroke engine with a capacity of 0.8 liters, consumes 630 g/kWh. Fuel consumption of the STIHL fs 50 CE gas tanks 20 percent lower. To everything, she throws 70 percent less harmful exhausts into the environment than models that have a two.Stroke engine.

Then there will be tips that specialists give users. They relate to the selection and use of the fuel mixture

Experts advise buying mainly gasoline of the AI-92 brand for trimmers. To prepare a mixture with a true ratio of oil and gasoline, you need to observe balance 1:30. Violation of this ratio leads to engine damage.

Store the mixture in containers that should be clean and safe. Since the fuel mixture sometimes defends, before making a refueling, you must definitely shake the canister.

It makes no sense to fill in gasoline more than you can spend. It is better then to add then than to clean the tank.

IMPORTANT! The lawn mower will last a long time and will be for a long time in the fuel consumption of one who strictly complies with the simple rules of storage of the trimmer.

The gasoline engine is a complex structure, and therefore requires constant care. That is why, before starting work, it is necessary to study the rules of operation of the device and follow the recommendations that the manufacturer developed.

It is necessary to constantly monitor the purity of the inner surface of the body. So that caustic juice from the grass does not corrode any parts of the device, experts recommend after the work is completed, clean the machine.

Before buying a mower, you need to determine the place where it will be stored. In this case, it is necessary to take into account what dimensions the unit has. It makes sense to take a closer look at the model that folds the handle. In this case, in any vault, she will find a place for herself. That is, for storing the device, this option is just perfect.

Device

There are models of gasoline lawn mowers without wheels. Their movement is carried out on the air cushion. Some have mulching knives grinding mowed grass, after which it is thrown out onto the lawn.

• Non.Self.Propelled ones that are moved by the lawn by hand by the operator.
• Self.Propelled ones that have a drive from the engine to wheels (often rear). The lever to control motion (turning on/off) is located on the handle.

Have vertical motors, therefore can be used on lawns, the slope of the surface of which does not exceed 15 °.

Gasoline consumption rates for trimmers

The consumption of all devices is approximately similar. To make sure of this, it is enough to compare several models.

Say, the Husqvarna 122C device, which has a two.Stroke engine with a capacity of 0.8 liters, consumes 630 g/kWh. Fuel consumption of the STIHL fs 50 CE gas tanks 20 percent lower. To everything, she throws 70 percent less harmful exhausts into the environment than models that have a two.Stroke engine.

Then there will be tips that specialists give users. They relate to the selection and use of the fuel mixture

Experts advise buying mainly gasoline of the AI-92 brand for trimmers. To prepare a mixture with a true ratio of oil and gasoline, you need to observe balance 1:30. Violation of this ratio leads to engine damage.

Store the mixture in containers that should be clean and safe. Since the fuel mixture sometimes defends, before making a refueling, you must definitely shake the canister.

It makes no sense to fill in gasoline more than you can spend. It is better then to add then than to clean the tank.

IMPORTANT! The lawn mower will last a long time and will be for a long time in the fuel consumption of one who strictly complies with the simple rules of storage of the trimmer.

The gasoline engine is a complex structure, and therefore requires constant care. That is why, before starting work, it is necessary to study the rules of operation of the device and follow the recommendations that the manufacturer developed.

It is necessary to constantly monitor the purity of the inner surface of the body. So that caustic juice from the grass does not corrode any parts of the device, experts recommend after the work is completed, clean the machine.

Before buying a mower, you need to determine the place where it will be stored. In this case, it is necessary to take into account what dimensions the unit has. It makes sense to take a closer look at the model that folds the handle. In this case, in any vault, she will find a place for herself. That is, for storing the device, this option is just perfect.

The reasons why the motorcycle consumes too much gasoline

We recommend that you familiarize yourself with this article to avoid problems like excessive gasoline consumption, and extend your life for your motorcycle.

Typically, the causes of excess gasoline consumption are problems with adjustment or mechanical problems. If you support the bike in good condition and use parts recommended by the manufacturer for repair, there is nothing to worry about. How you ride a motorcycle also affects fuel consumption.

One. Dirty air filters. This is the most common answer to the question of why a motorcycle spends so much fuel. If your problem is this, check the flow of air into the engine. With normal use, you need to change the filter every 30 thousand. Km. If you regularly drive in dusty areas, you should do this more often.

Poorly adjusted throttle. The motorcycle throttle is on the left side of the carburetor, but if it shifts, the bike begins to consume much more gasoline. If the motorcycle has not been used for a long time, it is not to get it without this lever. But after that, do not forget to return the throttle to the usual position to prevent the aforementioned fuel consumption.

Hard riding. If you drive aggressively, with unnecessary accelerations and braking, among other things, you will spend too much fuel. In addition, you will reduce the life of your vehicle: the engine and other spare parts will be wiser faster. It is also important to choose places for productive driving.

Inappropriate spark plugs. If you replaced the spark plug with a model not recommended by the manufacturer, this may cause problems. Thus, with any repair work, high-quality spare parts approved by the manufacturer should be used.

Cooper adjustment. Perhaps your motorcycle spends so much fuel due to an accelerated engine. You can adjust the idle speed using a disc on a carburetor. Find out from the manufacturer how best to do this: yourself or from a mechanic. Professional service costs will pay off a long bike service without unnecessary gasoline expenses.

Craftsman Weedeater leaking gas. Fuel line repair and replace.

Yamaha Motor Center Kirovsky © 2012-2018. The price agreement indicated on the site is not a public offer and can be changed. Clarify the relevant information on by phone. 8 (8452) 39-00-00.

Why is my car burning gasoline so quickly

When you buy your car, you must serve it well enough so that it reaches the maximum possible fuel savings. At first it may seem like an easy task, but in fact it is more complicated. You can ultimately neglect your car due to lack of time or money to invest in it. If your car does not pass the necessary preventive maintenance, you may ask yourself: “Why is my car burning gasoline so quickly”?

Why is my car burning gasoline so fast

Your car can burn more gasoline than usual.If your car burns gasoline more than usual, the problem can be mechanical or something else. Here are 10 main reasons why your car burns gasoline so quickly:

One. Low tire pressure

A low tire car carries the engine to increase the speed, which leads to a loss of miles on Gallon. Incorrect tires with the right PSI guarantees that your car will receive the best fuel savings. A good empirical rule is to pump tires four to five pounds per square inch less than the maximum value.The recommended tire pressure for your car is indicated on the sticker from the driver or on the tire itself. In addition, the presence of tires of the correct size also has a key value.

It requires replacement of motor oil? Visit our Car Fluid Guide website to find out about the importance of timely oil change, about which type of engine oil is best suited for your car, and much more.

Vacuum leak

Vakuum leak in the car leads to the impoverishment of the air-fuel ratio. As soon as this happens, the oxygen sensor binds to the electronic control unit to increase the fuel supply so that the engine does not work on the lunch mixture.This leads to a richer fuel mixture, which leads to a decrease in fuel consumption.

In most cases, you will notice that the engine has an uneven idle or idle up and down, as when searching. All these are signs of vacuum leakage. Other sources of vacuum leaks are seals of fuel nozzles, collector laying and laying of the throttle body. Elimination of vacuum leaks will increase fuel consumption and eliminate problems with idle.

Lenten fuel nozzle

Lenten fuel nozzle will definitely lead to a decrease in fuel consumption.Fuel nozzles are responsible for fuel injection into the combustion chamber. If they proceed, more fuel will be sprayed, and this fuel will be wasted. Some people prefer to repair their fuel nozzles instead of replacing them. Personally, I will always buy a new fuel nozzle.

Polluted or contaminated spark plugs

Polluted or contaminated spark plugs can cause poor fuel consumption. This happens when the fuel is injected into the combustion chamber, but the spark does not ignite the fuel.When the fuel is added to the cylinder and it does not burn, it is wasted. This leads to poor gasoline consumption. Replacing the spark plugs with new ones will provide good idle passage and better fuel savings.

Dirty air filter

Dirty air filter will definitely lead to poor MPG. When the air filter is dirty and clogged, the engine works with difficulty. This can even get out of poor conditions, causing engine overheating. Replacing the air filter with a new or its cleaning, if it is a KN filter, can increase the number of miles by Gallon to ten percent.It was reported that clean air filters can save up to 32 cents on Gallon or add up to 23 miles to the tank.

Jammed brakes

The jammed brake pads and calipers may not sound as you heard, but this will definitely lead to poor fuel consumption. I personally saw a loss of up to 15 miles on Gallon because of the stuck brake calipers. After the guides and brake calipers were clean and installed correctly, fuel consumption increased from 18 miles to Gallon to 36 miles per gallon.

In most cases, this may be the result of excessive lubrication of the guide bolts of the caliper. This leads to the formation of air s that do not allow the caliper to remain in the correct position, and leads to the fact that the brake pads are pressed against the rotor. In some cases, the brake caliper fails and requires replacement. Proper assembly of brake clamps and guide bolts of the caliper will help to achieve maximum fuel savings.

Free gas tank cover

The untouched gas tank cover can lead to a decrease in fuel consumption.This is because gas vapors are able to evaporate from the gas tank. Think about it as an open air alcohol. If medical alcohol is not sealed, then it will quickly evaporate. The principle is the same as with gasoline. Turning the lid of the gas tank into three clicks, you will make sure that the gas tank cover is securely closed and the gas pairs do not disappear. Studies show that a loose gas tank cover can lead to a decrease in fuel economy to 10%.

Eight. Cold engine driving

The car reaches the maximum fuel savings after the engine reaches the optimum temperature.Some engines warm up faster, some slower. Before the trip, it is important to warm up the engine. Now, if you have 5.6 short trips during the day, then you will have to warm the engine 5.6 times. This is where your day planning enters the game. If you plan your short trips and group them together, you will not have to warm up the engine so many times a day.

Nine. Avoid using the air conditioner

Try to ride without air conditioning when the weather allows.If you live in a hot place, driving without air conditioning may be impossible. But, if you live in a country with moderate temperature, try lowering the Windows and traveling so when it is possible.

Ten. Avoid sharp accelerations

This is the last reason that your car burns more gasoline than usual, but it may be the most important. You may be the biggest obstacle to the maximum efficiency of using your car fuel. If you like sharp acceleration, speed exceeding and do not go at a constant speed, all this can affect the fuel economy of your car.Try to accelerate smoothly and try to maintain a speed of 55 miles per hour. This speed is the best if you want to have a good MPG.

Why gasoline quickly leaves?

The catalyst can either be simply faulty (from low.Quality Russian gasoline he is very fast Convenurate), or is already knocked out. The absence of a catalyst increases the power slightly, but adds fuel consumption.

First of all, consumption fuel depends on the speed of the car. If we go too slowly or too fast. Fuel leaves more. Speed ​​at which a minimum of fuel is consumed. 60 km/h for the city and 90 km/h for the highway; Secondly, the higher the engine speed-the more consumption Fuel and lubricants.

How to dilute gasoline (AI 92) for Benzo braids, trimmer

At least briefly tell me the sequence

Let’s after the weekend? Write lot necessary. In fact, your property received free of charge. Your income. It is necessary to write off gasoline, how gasoline is issued to write off gasoline for a snow removal machine. I doubt the assessment of this income. Not to call an appraiser. Accounting for fuel and lubricants. That companies can write off gasoline and lubricants how to use. We must watch the normative. And you have nowhere else to write off this gasoline?I will add. It makes no sense to give all this body. Why? Yes, because in expenses you never write this property. Again why? It was received free of charge, but not paid. So you get a tax with the amount of free property received, but you can’t write off. The cost of gasoline will only reduce your tax base by 15%.Which is cheaper?There is another way out if you really want to write off gasoline. You can take this haying grinder for rent, let’s say from the founder, free of charge, t.E. Having issued a loan agreement. Evaluate it in the contract in the amount of 21t.R. How to dilute gasoline from technical conditions for trimmer contain gasoline with oil for. And for leased property, you can write off the costs of

Thank you, I understood with a mower, there is a small amount. It can be taken into account for accounting in order to give me the accountant the amount spent on the purchase of gasoline. But in tax accounting not to take into account. But I also have a purchase of acetylene for welding work. There is 25 thousand. Rub. Through the bank. Respectively, somehow should be present on the balance of the tank for welding. Maybe also skip out of the founder from lease? And they must be written off according to the acts of work performed or again you need to consider the hours of work, the consumption of this gas, etc.D.?

Carburetor device trimmer gasoline

Motokosa carburetor adjustment is a process that needs to be mastered for the full operation of the trimmer. Trimmer is a completely simple device that can break in only a few places and require mechanical repair or replacement of part. Adjustment of the carburetor device of the float.Type motorcycles may require knowledge of certain subtleties. The nuances due to the model and the specifics of its functioning will ensure a clear mixing and supply regime of the fuel mixture.

Carburetor of the lawn mowing Champion, how to adjust? This is just a trimmer of a float type. A common option designed to mix air and fuel in the proportions provided. The main problems arising during the operation of the motor are approximately similar to the problems that overtake the carburetor in the car:

• The motor can stall immediately after it managed to start. The reason is that gasoline is supplied in insufficient quantities. This is called “poor” fuel;
• Excessively fed gasoline leads to its incomplete combustion, excessive density of the mixture and uneconomous consumption.

Repair of the carburetor

Important! It is necessary to regulate the carburetor under different circumstances: a change in the temperature regime, octane fuel or type of oil, after winter or end of the run.In, load or spontaneous turning of the screws from strong vibration of the body. Some owners prefer to configure the module before each use to make sure of its correct work.

Gas consumption factors

This is a lot, given that another version of this device, electric, works for no more than twenty minutes.

As a rule, gas trimmers are usually equipped with two.Stroke engines. For them, experts advise using fuel with an octane number of at least AI-92, which is mixed with butter.

There are four indicators that affect gas mileage.

POWER. The higher this figure, the more fuel the unit is required. However, are the increased values ​​of this characteristic always preferable? Since four.Stroke engines consume more fuel than two.Stroke, they have greater power.

Devices in this sense are usually divided into groups, each of which corresponds to a certain area of ​​use. The engine can be:

-Light (one horse force or less, for example, Makita EBH 253 U),-simple (within 1-3 horsepower, for example, Redverg RD-GB330S),-reinforced (more than three horsepower).

It turns out that low.Power devices should have a fairly long period of work without refueling. However, in order to make these models cheaper and reduce their weight, the manufacturer sets not only small fuel tanks on them, but also engines, which in any case should be stopped. After all, they need to be cooled.

1-3 horsepower machines are usually classified as semi-professional. For them it is very usually installed more economical advanced engines.

In such devices, fuel consumption, of course, is more economical. As for the size of the tank, they are usually designed for one hour of continuous activity. Sellers and buyers polls showed that this category of units is the most popular.

THE MAIN THING! Due to its status, professional equipment is usually equipped with a powerful engine and a large tank. To simplify the user’s work, you can enter an option such as a wide shoulder belt.

When we are talking about such a gas trimmer, we mean that fuel consumption in it cannot be economical. After all, high power, as well as a large bevel width, inevitably lead to that such a device will require a lot of fuel.

You will pay much more than buying a four.Stroke engine than buying a two.Stroke. However, it works so that it does not create many emissions. In the end, fuel, which did not burn and remains unused, disappears with them.

If it is possible to choose a mode of operation, it also saves a gas trimmer. In this case, fuel consumption adjustment is carried out as necessary.

The surface of the region and its size. The lion’s share of the devices is designed to work on a flat surface. However, there are no ideal conditions. You can often find, for example, bricks and stones, branches and stumps, as well as other objects.

This automatically leads to fuel costs. And so, if someone has a violation on the site, then you need to make sure that the gasoline trimester has large wheels. They could provide the car with increased intersection capabilities. Thus, the trimmer will not strain and consume more fuel.

A set of functions. Most modern versions have additional options. This can be, for example, the ability to mow grass in hard.To.Reach angles or switch from one speed to another. It is clear that this can greatly facilitate all the work. However, such options may require additional fuel consumption.

Characteristics that affect gasoline consumption

The following parameters affect fuel costs:

Engine power and mowing width. First of all, fuel consumption depends on the type of engine. The more powerful it is, the more gasoline will need when working.

In addition, powerful engines are capable of providing a greater capture of grass. Knowing the width of the mowing, it is easy to calculate how many passages can be treated with the entire territory and what time will take for this. Based on the data specified in the instructions, you can establish how much fuel will be required to put the entire site in order.

Many modern modeling models are equipped with additional functions such as mulching or aeration. They significantly facilitate the care of the lawn. Along with this, all additional functions are very energy.Consumed. Accordingly, gasoline consumption will be greater when using them. It is also worth noting that self.Propelled models require more fuel than non.Self.Propelled.

The relief and size of the site also affect the amount of fuel spent when the mowing. Most lawnmands are created to work on a flat surface. If there are pits and bumps on the site, then it will be possible to avoid increasing fuel consumption if you purchase a model with enlarged wheels. They will easily overcome obstacles, and gasoline costs will remain the same. It is worth noting separately that front.Wheel drive apparatuses are more suitable for working with complex relief. They have greater maneuverability than the rear.Wheel drive models.

Several recommendations for choosing and using the fuel mixture

Favorable cooperation with the online store “Buy to the cottage”

The catalog on our website presents a rich assortment of gasoline trimmers. In order to make an order, just select the model you like and send it to the basket, and then wait for the manager’s call. We deliver goods to any region of Russia with the help of transport companies, in Moscow and Moscow. Our own courier service.Contact the specialists of our store, and they will definitely help you choose a model of a trimmer of the desired capacity with the desired consumption of gasoline. Call us right now by phone: 7 (495) 256-21-06 or 7 (495) 256-21-07. We work daily from 10.00 to 20.00.

Documents that justify the write.Off of the fuel and lubricants

Currently, it is not required to apply the norms of the Ministry of Transport of Russia when debiting gasoline costs. At the beginning of this year, the Ministry of Finance of Russia abandoned their long.Term categorical position and agreed that the Tax Code of the Russian Federation does not limit the company in accounting for fuel spent on official trips (letter of the Ministry of Finance of Russia of January 30, 2013. No. 03-03-06/2/12).

Gasoline Remote control robot lawn mower for garden

Representatives of the ministry confirmed their position in a letter of June 3, 2013. No. 03-03-06/1/20097. What should now be a complete set of documents in order to establish impeccable accounting of the fuel and lubricants, we showed in detail below. This includes documents from the driver, the primary from the seller of gasoline, depending on the method of acquiring fuel and lubricants and the company’s own papers.

In the article you will find ideal examples of two important documents that will help the accounting to justify the inspectors why the company attributes such a amount of gasoline. And in details they said that it is necessary to take into account when they are designed.

Act of control entry

From profitable clarifications of the Ministry of Finance of Russia, it should still be concluded that in the endless quantity, the costs of fuel and lubricants cannot be taken into account. They must be reasonable. This means that organizations need to introduce their standards. What are the sizes. The matter of each company, the main thing is that when checking it can be confirmed by their reasonableness documented.

The safest option is to FOCUS on the norms approved by order of the Ministry of Transport of Russia of March 14, 2008. No. AM-23-r. The inspectors will definitely not have questions. You can fix your choice in accounting policy for tax accounting or drawn up by order of the head, but take into account that the Ministry of Transport must be adjusted depending on the region, the load of routes, the population, the time of year, etc. D.

Over, according to some folk brands of officials, there are no officials at all, for example, for Nissan Juke, Renault Duster, Hyundai Solaris, Nissan Qashqai, Lada Largus and others. In this case, the norms can be approved independently taking into account the brand, modifications of the operated cars, the degree of wear, working conditions, transported goods, routes, etc. D. You also have the right to do if the indicator for the service car, indicated at disposal No. AM-23-R, does not suit (letter of the Ministry of Finance of Russia dated January 30, 2013. No. 03-03-06/2/12).

User manual

This document is a mandatory application to any model of mowing for grass. The instructions for the operation of a gasoline lawn mower contains:

• Description of the design of the unit, characters on its case, in t.H. Brands of the installed engine, gasoline consumption, oil;
• Instruction instructions with clarifications for the appointment;
• Safety precautions when handling a gas station;
• The procedure for spinning the grass;
• Maintenance of the device, care for it.

A mandatory section in the leadership is a list of possible malfunctions and options for their elimination.

Motokos on the mowing

Senocos continues-a suffering time for many villagers and owners of garden plots. One must prepare hay, the other should bake the site and lay the compost. Most of us have a familiar braid, some of us, some supports a senior, but trouble-free horse mowing in working condition, someone manages to use motoblock units in the case. For me, the “test” of the factory mower was already deplorable on the first day: after six hours of work it was smashed by the sudden vibration that arose suddenly.

The craftsmen explained to me that the mower scattered due to the fact that before operation I did not go through it, and the factories supply products collected in a hurry. Did not download the rights, but tried to quickly restore the mower. Moscow representatives of manufacturers quickly cooled my impulse, saying that enterprises supply units on sale only assembly. And these are already other prices.

The second time I did not want to step on the rake, so I decided to replace the walk.Behind mower with a manual motorcycle. According to information on the Internet, made an unexpected opening: domestic enterprises of manual motorcycle do not produce. Having rummaged into imports, he soon found what was needed: some trimmers with trimmer line equipped with special nozzles do not hammer mowed grass in fluff-prales, but neatly put them in rolls, like a manual scythe.

After consulting with sellers by phone, I chose the tool and immediately made an order. And he did not regret it: Senos spent on time and without much stress. In order not to make unauthorized advertising, I do not call the company, but I advise you to buy a professional motorcycle with a gasoline engine with a capacity of at least 1 kW, with wide shoulder belts, straight shaft and bicycle handles for a long mowing. Only with such handles can the capture be taken when running more than 1.5-1.8 m per passage. A little more expensive model with a two.Stroke engine, but it is easier and more powerful, moreover, it can be turned in your hands, as you like.

I will give other facts that vote for this tool: labor productivity is several times higher than that of a manual braid, since it cuts the grass in any direction, that is, motorcycles do not have idle. She is much more maneuverable “Lithuanian”, does not require a skill even from a novice mowing. She does not have a blade that would have to be constantly undermined, it can be easily mowed along the dew and dry grass, there is no much difference.

Without imposing my own opinion, I will give the characteristics of the main models of motorcycle and the calculation of their payback, I will also tell about the technique of the mowing

Motokos can be divided conditionally into household and professional, which are approximately twice as much. How to explain this?

Professional tool is designed for serious loads and constant use, it is reliable and repaired, its maintenance is technologically advanced. Sometimes unclean sellers give out household models for professional. With a careful examination, the discrepancy will necessarily be found. Why, for example, the carburetor is screwed to the plastic case on self.Tapping screws? There should not be a motorcycle professional for professional models.

When choosing a tool, ask the seller to show how to replace the nozzles, maintenance, check whether the air filter, the spark plug are conveniently changing, let him talk about the features of the assembly of benzos and its operation.

Comparative characteristics of some professional models of benzos

Each model has its own advantages: EFCO has an affordable price; Husqvarna’s models have a catalyst, a wide dealer network and reliability; STIHL. High specific power and low weight; Oleo-Mac-a favorable ratio of price and quality. Over, some models of Husqvarna and Jonshed are absolutely identical.

I must note that Motokosa is a modern high.Tech tool. Therefore, not cheap. But it is easy for them to work. It allows you to not only mow grass or lawn, but also cut small trees and shrubs. With motor skots of some models, such as OLEO-MAM, you can use special nozzles-a cultivator or a high-precision saw. But most of the bush and motorcycle can use 5 main types of nozzles.

When working with a trimmer nozzle, you must definitely wear goggles. So that in the evening you do not buzz with tin, protect your ears with headphones, or at least insert the bears.

Two.Stroke engines of motorcycle requires high.Quality 92 gasoline in a mixture with special oil. If this gasoline is mixed with ordinary engine oil for four.Stroke engines, this can damage the tool engine. It is not worth refueling this tool with ninety.Fifth gasoline, I will say it by its experience. It will not be better: this fuel variety causes uneven operation of the engine and overheating. First of all, before work it is necessary to fit the shoulder belts: they must tightly fit the body, otherwise they will constantly slide. Then we hang the tool, fix it with a latch by the eye and achieve balance.

The German company STIHL recommends cutting off the grass, leading the knife of the braids from right to left, which facilitates the process of mowing and forming the roll on a beveled surface (see. Scheme 1). I am a cat in this way that recommends for the ineffective herbastens Jonshed (see. Scheme 2), it certainly requires a lot of effort, but the speed of the mowing increases, since the grass is mowed when the braid moves in both directions.The right to the left and left to right to the right. In this case, 2 rolls turn out: on the left. Thicker, on the right. Thinner. It depends on the rotation of the disk counterclockwise, which throws the grass to the left. If the grass is too thick, you have to use a single.Sized method (scheme 3). I, a physically fairly strong person, had to mow the easily confused clover with a yield of up to 40 centners per hectare in a two.Way way.

What is the fuel consumption of motorcycle? Mine, according to the operating instructions, “eats” 500 g per kilowatt hour. This means that with a power of 1.3 kW of a benzokos will spend 0.8 liters of fuel per hour, that is, a tank with a volume of 0.5 liters is enough for 35-40 minutes. Of course, when working with a trimmer or a shrub of fuel, much more is consumed than with a kosbe of grass.

It is unequivocally impossible to say what time your Motokos will pay off for: it is one thing if you work for yourself by crowding the site, there will be a completely different account when you and your scythe go to work, which is quite possible. In 10 days of vacation, I managed to calmly infuse about 4 tons of hay, if necessary, could more. I think that a good professional tool will pay off fast enough. Good luck on the mowing!

Motokos on the mowing

Senocos continues-a suffering time for many villagers and owners of garden plots. One must prepare hay, the other should bake the site and lay the compost. Most of us have a familiar braid, some of us, some supports a senior, but trouble-free horse mowing in working condition, someone manages to use motoblock units in the case. For me, the “test” of the factory mower was already deplorable on the first day: after six hours of work it was smashed by the sudden vibration that arose suddenly.

The craftsmen explained to me that the mower scattered due to the fact that before operation I did not go through it, and the factories supply products collected in a hurry. Did not download the rights, but tried to quickly restore the mower. Moscow representatives of manufacturers quickly cooled my impulse, saying that enterprises supply units on sale only assembly. And these are already other prices.

The second time I did not want to step on the rake, so I decided to replace the walk.Behind mower with a manual motorcycle. According to information on the Internet, made an unexpected opening: domestic enterprises of manual motorcycle do not produce. Having rummaged into imports, he soon found what was needed: some trimmers with trimmer line equipped with special nozzles do not hammer mowed grass in fluff-prales, but neatly put them in rolls, like a manual scythe.

After consulting with sellers by phone, I chose the tool and immediately made an order. And he did not regret it: Senos spent on time and without much stress. In order not to make unauthorized advertising, I do not call the company, but I advise you to buy a professional motorcycle with a gasoline engine with a capacity of at least 1 kW, with wide shoulder belts, straight shaft and bicycle handles for a long mowing. Only with such handles can the capture be taken when running more than 1.5-1.8 m per passage. A little more expensive model with a two.Stroke engine, but it is easier and more powerful, moreover, it can be turned in your hands, as you like.

I will give other facts that vote for this tool: labor productivity is several times higher than that of a manual braid, since it cuts the grass in any direction, that is, motorcycles do not have idle. She is much more maneuverable “Lithuanian”, does not require a skill even from a novice mowing. She does not have a blade that would have to be constantly undermined, it can be easily mowed along the dew and dry grass, there is no much difference.

Without imposing my own opinion, I will give the characteristics of the main models of motorcycle and the calculation of their payback, I will also tell about the technique of the mowing

Motokos can be divided conditionally into household and professional, which are approximately twice as much. How to explain this?

Professional tool is designed for serious loads and constant use, it is reliable and repaired, its maintenance is technologically advanced. Sometimes unclean sellers give out household models for professional. With a careful examination, the discrepancy will necessarily be found. Why, for example, the carburetor is screwed to the plastic case on self.Tapping screws? There should not be a motorcycle professional for professional models.

When choosing a tool, ask the seller to show how to replace the nozzles, maintenance, check whether the air filter, the spark plug are conveniently changing, let him talk about the features of the assembly of benzos and its operation.

Comparative characteristics of some professional models of benzos

Each model has its own advantages: EFCO has an affordable price; Husqvarna’s models have a catalyst, a wide dealer network and reliability; STIHL. High specific power and low weight; Oleo-Mac-a favorable ratio of price and quality. Over, some models of Husqvarna and Jonshed are absolutely identical.

I must note that Motokosa is a modern high.Tech tool. Therefore, not cheap. But it is easy for them to work. It allows you to not only mow grass or lawn, but also cut small trees and shrubs. With motor skots of some models, such as OLEO-MAM, you can use special nozzles-a cultivator or a high-precision saw. But most of the bush and motorcycle can use 5 main types of nozzles.

When working with a trimmer nozzle, you must definitely wear goggles. So that in the evening you do not buzz with tin, protect your ears with headphones, or at least insert the bears.

Two.Stroke engines of motorcycle requires high.Quality 92 gasoline in a mixture with special oil. If this gasoline is mixed with ordinary engine oil for four.Stroke engines, this can damage the tool engine. It is not worth refueling this tool with ninety.Fifth gasoline, I will say it by its experience. It will not be better: this fuel variety causes uneven operation of the engine and overheating. First of all, before work it is necessary to fit the shoulder belts: they must tightly fit the body, otherwise they will constantly slide. Then we hang the tool, fix it with a latch by the eye and achieve balance.

The German company STIHL recommends cutting off the grass, leading the knife of the braids from right to left, which facilitates the process of mowing and forming the roll on a beveled surface (see. Scheme 1). I am a cat in this way that recommends for the ineffective herbastens Jonshed (see. Scheme 2), it certainly requires a lot of effort, but the speed of the mowing increases, since the grass is mowed when the braid moves in both directions.The right to the left and left to right to the right. In this case, 2 rolls turn out: on the left. Thicker, on the right. Thinner. It depends on the rotation of the disk counterclockwise, which throws the grass to the left. If the grass is too thick, you have to use a single.Sized method (scheme 3). I, a physically fairly strong person, had to mow the easily confused clover with a yield of up to 40 centners per hectare in a two.Way way.

What is the fuel consumption of motorcycle? Mine, according to the operating instructions, “eats” 500 g per kilowatt hour. This means that with a power of 1.3 kW of a benzokos will spend 0.8 liters of fuel per hour, that is, a tank with a volume of 0.5 liters is enough for 35-40 minutes. Of course, when working with a trimmer or a shrub of fuel, much more is consumed than with a kosbe of grass.

It is unequivocally impossible to say what time your Motokos will pay off for: it is one thing if you work for yourself by crowding the site, there will be a completely different account when you and your scythe go to work, which is quite possible. In 10 days of vacation, I managed to calmly infuse about 4 tons of hay, if necessary, could more. I think that a good professional tool will pay off fast enough. Good luck on the mowing!