Why does the line fly out of the trimmer reel

Thread shape

It is necessary to choose a line not only in thickness, but also in shape, for this reason: the cord does not cut the stem, but interrupts it. The rotating string hits the surface of the stem many times and eventually separates the top of the stem. For this job, the shape of the incisal edge is an important technical characteristic.

• Round. the most common, as it is universal: you can choose it for mowing both fresh and dry grass. It is considered less noisy, especially spiral. But this parameter is not important in all cases. The line for a gasoline trimmer can be as noisy as you like, it is still inaudible while the engine is running.

• Polygonal. from 3 to 6 faces. Sharp incisal edges handle coarse, thick stems better. So, a square cord with a cross section of 2.4 mm is able to remove raspberry stems. It should be noted that with a higher efficiency, the polygonal cord is consumed faster, and it should be used only for its intended purpose.
• Curly. an asterisk, ribbed, in the form of a twisted square with notches, and so on. Their “specialization” is different, which it is advisable to learn about in the instructions before choosing. Thus, an asterisk is recommended for cutting fresh grass, as it is less traumatic: the grass after cutting does not dry out, as when using a round string. In the photo. a cord with a different shape.

Why lawn mowers?

This type of gardening equipment is designed for small areas where maneuverability is more important than performance. If we are talking about the same flower bed, then mowing the grass in the immediate vicinity of the flowers using a wheeled lawn mower is unrealistic. The trimmer, electric or petrol, will do the job just fine.

The essence of his work is as follows: the fishing line or knife rotates at a fairly high speed and cut off the stems. A string or cord is used specifically for cutting grass. Which trimmer line is best depends on the task. For soft and hard grass, respectively, you need a cord with different technical characteristics.

Trimmer line: features

There are several parameters to consider to choose the right string. Firstly, the characteristics of the device must indicate how thick the line can be. When trying to thread a cord with a large diameter, the thread on the spool will get tangled, the engine will overheat, and the bushings will wear out much faster. Secondly, the task matters. mowing the lawn grass or cutting dead wood. The power of the device itself also puts its limits.

Which trimmer line is better: which one to choose?

Caring for a lawn or flower garden includes not only watering and weeding, but also cutting the grass. Bare land on a flower bed or summer area looks unattractive. Smooth, soft, green “carpet” is certainly much better.

Choosing a trimmer line

But to make the lawn look like this, you need special equipment.

How to change the spool & line on the Flymo Mini Trim Auto ST grass trimmer

Manufacturing material

The line is made from nylon. polyamide, or polypropylene. In cheap products, there may be an additive of polyethylene. It significantly reduces temperature and wear resistance.

Long-lasting polypropylene trimmer line can become brittle. It is recommended to soak it in water for 30 minutes before use.

In strings with a large diameter of 4 mm, aluminum particles are added to increase strength.

Do not use cables or wire in lawn mowers: pieces of wire broken off at such a high speed easily pierce leather shoes.

Cord thickness

Trimmer line section ranges from 1.2mm to 4mm.

• 1.2 mm. 1.6 mm. a thin string designed for constant lawn care. It is used in low-power devices. up to 0.5 kW. This is a standard line for an electric trimmer.
• From 2 mm. 2.4 mm. suitable for devices with a power of 1 kW. This is the most common option, as it allows you to cut both young and rather tough grown grass. Since the lawn in the dachas is looked after a little less often than it should be, the 2.4 mm cord turns out to be very useful.
• 3mm. 3.2mm is used for powerful gasoline appliances. Their task: to cope not only with grass, but also with thick stems of weeds and dead wood.

Some manufacturers paint the cord with different cross-sections. So, the Stihl trimmer line with a diameter of 1.6 mm is blue, with a section of 2 mm. green, the popular 2.4 mm is colored orange.

The string is sold in a package. bays, the length ranges from 10 to 100 m. However, there are also options for selling “for a cut”. In the photo. various types of cord with a cross section of 2 mm, 3 mm, 4 mm.

Reels for cord: characteristics

The trimmer head is, in fact, a special reel of line for the trimmer. Inside it, on a spool, a cord is wound. as a rule, up to 15 m. A thread of the required length is pulled from it when it breaks or is worn out. When the string ends, a new thread is inserted into the bobbin.

By the type of cord feeding, the drums are divided into:

• manual. to lengthen the string, the device is turned off, and the fishing line is manually pulled out;
• semi-automatic. activated by a favorite folk trick: you need to hit the mowing head on the ground. On impact, the anchor mechanism is released and the cord is automatically lengthened;
• automatic. here you need to reduce the speed, and then increase it again to the maximum: the spool will feed the thread when the speed increases.

The line trimmer drum is also refueled differently. In quick-charging ones, there is no need to disassemble the coil for refueling, in ordinary ones. you need to remove it and wind the cord manually. The video shows different ways to change the string.

3 comments on “Which trimmer line is better: which one to choose?”

What kind of fishing lines I have not used all are torn like devils, I honestly do not know at all what to do next. Either they “slip in shit” or “fake”. Any shit. If anyone knows how and where to find a “contractual” system. This is a BIG QUESTION.

2.4. Star. This is if you want to stock up on hay. And for grinding. round.

Curly cut more accurately. And the round ones throw around.

Trimmer line: types, ways of winding lawn mowers on a reel

The speed of electric and lawn mowers is largely influenced by the quality of the fishing line. The consumption of the cord itself, as well as the load that acts on the engine, depends on how correctly it is wound on the mowing reel. In this regard, each gardener needs to carefully study the rules for choosing and independently installing a fishing line on a reel. This will prevent premature breakage of the scythe and make its use in the garden more convenient and efficient.

Features of the use of trimmers

A trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, flower beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device, like a trimmer, exists in several variations:

• petrol;
• rechargeable;
• electric.

As the names suggest, trimmer types differ markedly from one another. But regardless of the type of this tool, a fishing line can be its cutting element. Of course, the line tucked into the trimmer reel is not endless. And sooner or later you will need to replace it with a new one.

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the trimmer, the more active the line is used in it. And, accordingly, the faster it will end. In this regard, the question arises: how to thread the line into the trimmer spool?

The first way to wind the line

The required amount of line has been cut off. Now you need to carefully examine the bobbin in order to understand what type it belongs to. It depends on how the line is to be wound on it.

There are two types of bobbins. In general, they differ slightly from each other. Regardless of the type, the coil is divided into two sections. upper and lower. In the first type, the dividing edge does not close into a ring and has a depression.

In the second type, it is solid, but near it there are small through holes on the sides on both sides. The method of winding the thread must be studied depending on which of the above types the coil belongs to.

• The previously prepared six-meter segment must be bent in half. It is best not exactly in the middle, but in such a way that one half is about fifteen centimeters longer.
• Then the place of the fold must be inserted into the recess in the dividing face. One half of the line should be at the top of the spool, the other half at the bottom.
• Now you can start winding directly. You need to wind in the direction of the arrow on the bobbin. When winding, you need to hold the threads so that they do not intertwine and the upper half winds up in the upper part of the spool, and the lower half in the lower part. Each half should have about fifteen centimeters free from the end.
• There are small indentations (or, in other words, grooves) in the upper edge of the bobbin for securing the consumable. The ends of the threads must be inserted into these grooves so that they are fixed against each other.
• The final stage of threading the consumable into the tool. the ends attached to the bobbin must be threaded into the corresponding holes in the trimmer head.
• That’s all. The winding process is complete. Now all that remains is to assemble the head into a single whole. The spring fits neatly back between the bobbin and the head. Then you need to insert the bobbin into the head and press them together.
• It is recommended that the free ends of the thread be pulled out more. To do this, pull the ends of the consumable one by one so that they are removed from the grooves of the bobbin. You can make sure that the cutting element is removed from the retaining grooves by trying to pull the threads a little. they should freely exit through the holes in the head.
• While pressing the bobbin down, you need to put the cover over it. The cover must be screwed to the head so that all the grooves on their bodies are aligned and the bobbin remains fixed between them.
• And finally, the very last action. the head is screwed back into place at the bottom of the tool.

The process is complete. The line is tucked into a reel. The trimmer is ready for further work.

How to wind the line onto the trimmer spool

At first glance, threading a line into the reel of a tool is not an easy task. But it is enough to carefully study this process. and in the future, all the necessary actions will be performed without any difficulties.

It is worth reading this guide to find out how to tuck the line into the trimmer. The step-by-step instructions below take into account the peculiarities of the coils of different types of trimmers, therefore, it is applicable to any tool.

So, the procedure is as follows.

• The line spool is the bottom end of the trimmer. First of all, of course, you need to remove this head from the device. To do this, you need to fix the rod (or, in other words, the shaft) on which the coil is attached. It is required to fix it in such a way that it does not scroll. The easiest way to do this is by placing a kind of stupor (preferably metal) between the shaft threads through a special hole. When the shaft is fixed, the spool can be unscrewed.
• At this stage, you have to remove the bobbin from the head, on which the fishing line is attached. To do this, you need to disassemble the head into elements. To do this, you first need to find a retainer on its body. It is located on the circumference of the product and is like a button. When the latch is found, you need to press it firmly. Keeping the latch pressed, turn the head cover clockwise. Then you need to remove the cover and remove the bobbin.
• A tight spring is placed between the bobbin and the head. It needs to be put aside for a while so that it does not interfere with the winding process. Before proceeding with the step of winding the line, it is necessary to inspect the bobbin. If there are remnants of old fishing line on it, they must be removed. When the bobbin is cleaned, you can start preparing a new bobbin.
• From a previously prepared skein of new fishing line, it is necessary to measure and cut off six (maximum. seven) meters. Keep the bobbin close at hand.

At this point, the key stage actually begins, which this article is devoted to.

What does the thickness of the cord affect??

The diameter of the fishing line determines its effectiveness when mowing various types of wild vegetation.

Today on the market you can find cords of the following thickness:

• 1.6 mm. fishing line for cutting young soft grass;
• 2 mm. a cord with this thickness is used mainly for mowing young wild vegetation and small weeds;
• 2.4 mm. This line is designed for removing young weeds and mowing large volumes of overripe wild vegetation;
• 2.7 mm. this type of cord is used for effective control of large weeds;
• 3 mm. line with this thickness effectively copes with the removal of small bushes and thick old weeds;
• 3.3 mm. this cutting line is suitable for removing thin shoots from young wild trees;
• 4 mm. the large thickness of this line allows it to cut large lumber weeds and thick shoots of wild trees.

It is important to remember that the larger the diameter of the cutting line, the higher its noise during operation. In addition, thick lines should only be used on high horsepower trimmers. For example, only mowing heads with a cord thickness of less than 2 mm can be used on electric line and knife trimmers. Otherwise, the garden tool engine will overheat quickly.

How to insert line into the trimmer?

Filling the mowing reel with cutting thread for a trimmer is not difficult, but novice gardeners will have to practice a little in order to be able to quickly insert the cord into an existing utility trimmer in the future.

There are several ways to refuel the trimmer cutter head. The first method is the easiest and works well for beginner gardeners.

In this case, the cord is inserted into the spool in the following sequence:

• First, you need to rewind about 6 m of trimmer line from a common spool, and then cut the resulting segment in half. The result should be 2 threads, each 3 m long;
• Then, at one of the ends of the first segment, you will need to make a kind of hook, and insert it into one of the through holes located in the upper part of the spool;
• Next, you need to start winding the line on the spool in the direction indicated by the arrow. During winding, you need to make sure that the line lies evenly on the surface of the spool, and does not go beyond its upper section. You do not need to wind the segment to the end, about 15 cm of thread should remain in your hands;
• The remaining free end of the wound cord will need to be inserted into one of the recesses located at the top of the spool;
• Further, the same procedure will need to be done with the second piece of fishing line. It will need to be wound around the lower section of the spool;
• As in the first case, you do not need to wind the line all the way to the bottom section. The remaining piece of thread will need to be inserted into the second groove of the bobbin.

After the operation has been completed, the coil will need to be installed on the trimmer and wound up. To check the reliability of the thread attachment, you will need to press the throttle lever all the way so that the engine reaches maximum rpm. If the line does not fly out of the head, then the line is held securely, and it will not fly out of the mowing reel when mowing the grass.

Second winding method

• A previously prepared segment of six meters in length is required to be bent exactly in the middle and cut. Thus, two segments of the same length are obtained.
• At one end of each segment, you need to make a small “hook”. To do this, it is necessary to bend a couple of centimeters from the edge and fix it for a short time so that the “hook” does not unbend.
• Then one segment is taken. The hook is inserted into the through hole at the top of the bobbin.
• Now you can proceed to the key stage. winding. The direction in which to wind is indicated by an arrow on the bobbin. It is important to ensure that the line is wound strictly within the upper part of the reel. You do not need to wind the thread to the very tip. about fifteen centimeters should remain free from the end.
• In the upper edge of the spool there are small recesses (so-called grooves) for fixing the consumable. The loose “tail” of the thread must be inserted into one of these grooves.
• The top of the coil is tucked in. Now you need to do the same procedure with the bottom. Take the second piece of thread. The “hook” is threaded through the through hole at the bottom of the bobbin.
• After that, you can start winding the fishing line (within the lower compartment). And for this segment, you also need to leave about fifteen centimeters free from the end. This remaining “tail” must be inserted into the notch opposite to the one into which the end of the first segment was inserted.

The subsequent steps for this type of coils are exactly the same as described for the previous type in paragraphs five to nine.

This is how the line in the trimmer spool changes. There is nothing complicated in the process. And already after several refuelings, all actions will come to automatism.

To visually study the process described above, you can turn to the Internet for help. On the popular YouTube portal there are many different videos showing how to wind the line on the trimmer reel.

How to wind the line around the trimmer cutter head or lawn mowers

Master class: weaving the “Tree of Life” pendant from wire

Spring has fully entered into its legal rights and we thought that today’s master class on weaving a wonderful “Tree of Life” pendant made of wire would be just right for the theme. After all, what is spring if not the rebirth of life after a long sleep? The ancients reasonably imagined the annual cycle of the seasons precisely as the sequential movement of nature from birth to death, and spring quite naturally symbolized precisely its birth.

The very same symbol “Tree of Life” is found in almost all world cultures.

Whatever it was, but the image of the Tree has a uniquely positive meaning, symbolizing the unity of nature and the eternal cycle of life.

In our master class, we will use the Celtic version of this symbol, which is most widespread in the modern world and is often used in the production of decorative products, jewelry and cult attributes.

We wish you pleasant and, most importantly, successful creativity.!

Sketches of the “Tree of Life”, they are easy enough to find on the Internet.

Why does the line fly out of the Stihl trimmer reel

Let’s take a look at the representatives of the world’s most famous spool brands on the Russian market:

Stihl Line Trimmer- How to Quickly Exchange the Head in 20 seconds.

Having met the cord with hard objects, it sharply stops, under the influence of which the forest gets inside the device. It lies under the spool and sticks together. To improve the situation, it will be necessary to suspend work and lay the line again. In the role of prevention of similar inconveniences, it is recommended to treat the forest with silicone grease before installing it into the coil.

In the device of the Autocut trimmer head, as well as in other automatic models, two parts of the main element are distinguished: the body and the spool. Spring mechanisms are provided in both parts. The spool can be produced in several configurations:

• Modifications with one section. Under these circumstances, both ends of the line are wound together.
• Models with a pair of compartments. Here who’s edge is wound on a certain element. This design is more effective, makes it possible to avoid tangling of the forest and its sintering.

It is possible to redesign a single-section spool to a version with 2 chambers. For this purpose, you will need a strong plate, from which a circle is cut with a diameter similar to the thickness of the spool. This part is in free movement. Then a cut is made on the ring, mounted on the head and fixed with tape or glue.

The universal trimmer head can be equipped with holes from 2 to 4 pieces. They are opposite each other. The ends created for mowing are derived from these parts. Apart from the indicated types of bobbins, there is a head designed for a certain size of the scaffold. In such coils, the number of whiskers increases to a dozen. Among users, the views were divided about such devices.

Some consider a similar unit to be more effective. Others are convinced that the line consumption will be significantly higher with an incomprehensible increase in the quality of work. Already today, in order to change the forest, the process must be interrupted. When choosing a trimmer, consider the terrain and vegetation properties. Subsequently, it will not be difficult to find an option that normally fits in a certain situation.

What do consumers say about the Husgvarna T45X trimmer head? As the owners note, this element has practically no drawbacks, except for the higher price. But there are a lot of advantages in this part. Among them:

This model is suitable for summer residents, gardeners, utilities. It is used with braids, the diameter of the working shaft of which is 3-3.4 mm.

My own master

Tool for giving and home

Why The Line Doesn’t Come Out In The Trimmer Head

Trimmer heads contain a cutting element, a special rod, a propeller and a control mechanism with a handle. The unit is intended for cutting grass in the courtyard area and garden plots. The compactness of the device and ease of control allow you to do excellent work in the most inaccessible places. When using this unit, it is possible to prune shrubs and a young garden. Adjustable elements allow you to set the desired cutting height for grass on lawns and grounds.

In the process of selecting trim heads, the following characteristics are assessed:

Husqvarna trim heads are classified according to line feed method, specifically:

• Manual type. The line is fed in this option by the mechanical method. To lengthen the cord, you will need to pause the device and pull out the edges of the cutting part by hand.
• Semi-automatic. Such instances allow you to create a change of cord without touching the head of the ground surface. This function is feasible using a special button and an anchor mechanism, which makes it possible to lengthen the working part of the line through the use of centrifugal action. In principle, the whole procedure is carried out with the unit turned on.
• Automatic trimmer heads are distinguished by the fact that during their operation, the cord lengthening is performed in the automatic mode after lowering the engine speed. Line feed is carried out as a rule.

Of the above devices, the manual option is not entirely convenient and comfortable. Automatic options are also not popular due to the huge line consumption. A good version would be automatic execution.

Why does the line fly off the trimmer

How to make a coil yourself

The basis of a homemade reel is a disc made of durable material. It is best to use textolite about 5 mm thick for these purposes. It is strong and reliable enough. The size of the disc depends on the size of the trimmer and personal experience. how is it more convenient to work.

Next, a hole should be drilled in the center of the disc. The diameter of the hole should be equal to the diameter of the rod axis (the latter is attached to the rotating shaft of the motor). In this case, it is extremely important to determine exactly the center of the disc. After that, 4 holes should be drilled for the line. Their diameter will be equal to the diameter of the fishing line, and they will be located in pairs on opposite sides of the axis (2 on one side, 2 on the other from the axis of rotation). In this case, the design of the reel is greatly simplified: it is not required to wind a large amount of fishing line, but it is enough to fix (tie) a small piece of it through the ready-made holes.

To give the structure the necessary strength and reliability, it is recommended to find a spring, the inner diameter of which will be equal to the diameter of the shaft, and install it on the shaft over the finished disc.

After the line is tucked in and secured to the disc, you can start testing. The fishing line does not need to be fixed on the disc: even when threaded through the holes, it will not fall out, because the engine gives high revolutions to the shaft, and the centrifugal force is enough to hold the fishing line under load.

This design, instead of a purchased trimmer coil, has many advantages: you can install any line (both thin and thick) into it, the device itself is practically “indestructible”, and it will not take a very long time to acquire a new coil.

The disadvantages of this homemade product include the following:

• the need to cut a pair of pieces of fishing line of the same length;
• when installing without attaching the fishing line, it is necessary to make sure that equal lengths of fishing line hang from the reel.

Video about winding the line on the trimmer reel:

The body can be used from an old coil. it rarely breaks.

How to wind the line around the trimmer cutter head or lawn mowers

The video shows in detail how to wind the line on a trimmer reel or lawn mowers. Refueling with mowing line.

What is a trimmer

Under the trimmer, lawn mowers or electric mowers are assumed. In practice, this is one of the types of lawn mowers (hand mower), which are designed for mowing grass. This is a modern braid. Initially, they were developed for agricultural work, but the main application of trimmers was specifically lawn mowing.

For the first time the idea to make a trimmer came to mind of the South American businessman J. Bollas. Driving through an automatic car wash, he saw that the spinning brush principle could be used to mow crops.

Then he assembled a simple trimmer from a tin can (as a spool) and a line threaded through the holes drilled in it. He installed the resulting structure on a pole, on which the engine from a moped was previously mounted. The device mowed not only wheat, but also grass. The trimmer spool device and comes out of the spool. The line is not why it stalls. Realizing that he would earn huge amounts of money on the sale of the scythe, the businessman improved his product and gave him the title “Weed killer”. A feature of the invention was the ability to mow the grass around the trees. the forests cut the grass perfectly, but did not injure the bark.

The main purpose of such a tool was to mow grass in small areas in places where traditional wheeled equipment cannot be applied:

• in the presence of a huge number of shrubs;
• in gardens with a huge number of trees;
• near fences and fences;
• if the site has uneven terrain.

All trimmers are equipped with a barbell. the main structural element. A gasoline or electronic engine is attached to the bar from the 1st end, and a reel with a fishing line is put on the other. the main working element. With all this, the type of transmission can be at least some. it is limited only by the capabilities of the manufacturer and commercial parameters.

How to wind the line around the trimmer cutter head or lawn mowers

The video shows in detail how to wind the line on a trimmer reel or lawn mowers. Refueling with mowing line.

How to wind the line around the trimmer cutter head or lawn mowers

The video shows in detail how to wind the line on a trimmer reel or lawn mowers. Refueling with mowing line.

Why The Line Is Not Coming Out Of The Trimmer Head

Step by step annotation on how to wind the line on the trimmer spool

With the arrival of spring, you often spend your time at the dacha or in your personal plot. The trimmer will protect you from obstacles such as grass and weeds. This tool easily trims and mows grass in difficult areas, where an ordinary lawnmower cannot do it. The trimmer is a very effective and successful tool for mowing grass along fences, flower beds, houses and aisles in the garden. the cord spontaneously comes out of the trimmer on the ground of the line of the head. The line may not. A number of types of garden trimmer have been invented (gasoline, electronic and battery). It would seem that everything is fine, in your arsenal there is such an excellent assistant, but over time, the cutting element wears out and it becomes necessary to replace the finished line. And how to fill the line in the trimmer, not everyone knows. Line feed system from trimmer rather than trimmer line, I can’t understand why. We suggest using a step-by-step annotation with attached photos.

Instructions on how to wind the line on the trimmer spool

• 1. First you need to disassemble the trimmer head. Click on the latch on the product body and turn the cover clockwise. Removing the bobbin.
• Now we have to figure out how to wind the line on the trimmer reel. We measure out about 6-7m of fishing line and insert its end into the hole of the bobbin.
• We reel the fishing line from both sides. The winding direction is always indicated by an arrow on the bobbin.
• Leave the ends of the 15 cm long cutter free. Do not wind too much line. Leave 6mm between the outer edge of the bobbin and the line.
• Insert the remaining two ends of the line into opposite holes in the bobbin.
• We fix both ends in the grooves on the head body.
• The spring is carefully placed back into the bobbin guides and into the head body.
• In order to thread the line into the trimmer correctly, it is necessary that the bobbin goes back into the head body (press it lightly). Pull the loose ends of the line out, if necessary. Pull the ends of the cutting element sharply one by one so that they come out of the grooves in the bobbin and pass freely through the holes on the head.
• So, we figured out how to wind the line on the trimmer reel. It remains only to align all the grooves on the head body and close the lid. Then we press on the bobbin and begin to rotate it counterclockwise until it stops. While holding the bobbin, turn it slightly clockwise and release it. The fishing line comes out Inspection of the head if the fishing line does not come out of the spool itself during carrying. If there was a clicking sound, then it snapped into the head. If this did not happen, then you need to repeat the action again.
• Pull out the loose ends of the line until they stop.