Why The Mower Stalls

The brushcutter stalls when the throttle is pressed The brushcutter stalls when the throttle is pressed text_error The trimmer stalls when the throttle is pressed Those who have lawns on their personal plot know that the trimmer is quite a useful thing.

The brushcutter stalls when you press the gas

As you can see, there are many reasons why the trimmer can stall when you press the gas. That is why it is important to monitor the state of your assistant, check the state of all systems of the mechanism in time.

Lever metal shears

During construction work, there are situations when it is necessary to cut sheet metal. To cope with this problem will help such a convenient tool as lever scissors, designed for curly and straight cutting. Their characteristics are described in this article.

Trimmer disc

Typically, regular garden grass trimmers are used with a line. But if you need to cut young growth of shrubs or trees or very tough grass, you cannot do without a disc trimmer. Read about trimmer discs in the article.

Many novice seamstresses pay a lot of attention to the choice of a sewing machine, thread and fabric, and at the same time completely forget about scissors. But high-quality scissors are among the basic tools of a tailor. Our article will tell you more about them.

Loofah sponge

Cosmetic procedures at home, skin rejuvenation, getting rid of cellulite, all this becomes possible thanks to natural loofahs, which literally grow on branches. What are the advantages of loofah sponges, what are the subtleties of their use and cultivation in the article.

Ivan Kireev: shit

Igor Andreychin: Thanks for the competent review, everything is very clear and accessible !! I also took a Tatra Garden BCU-50 petrol cutter for myself, I have already passed the entire section twice, I am very happy with the choice! I advise everyone! I would like to advise everyone else to buy such tools with a guarantee from the office. Since the saved UAH 200-300.

The trimmer stalls when you press the gas

Why The Mower Stalls

Those who have lawns on their backyard know that a trimmer is quite a useful thing that will help you quickly and efficiently tidy the lawn or clear weeds from overgrown areas. And, like any mechanism, it also often fails due to various breakdowns. One of the most common complaints from device owners is that the trimmer stalls when you press the gas. We propose to understand the main reasons for this phenomenon and identify ways to solve the problem.

Why does the petrol trimmer stall

The benzokos starts up and stalls. What to do?

1. There is a spark, and everything seems to be normal, but the petrol cutter will not start, in such cases, you should check the air access valve to the fuel tank. A clogged valve leads to the creation of a vacuum in the tank, in which the carburetor does not receive enough gasoline, so the petrol brush will start, but then stall. To exclude this reason, you need to clean the valve and try to start a petrol cutter with a tank cap that is not completely twisted.
2. If the brushcutter does not start at the same time, you should remove and clean the fuel filter, as well as check all the carburetor parts, and then try to start. The petrol cutter will not start again, the air filter is disconnected, try to start without it, if the mower starts up, the reason is in the air filter, replace it.

The petrol cutter will not start, the spark is gone

The loss of a spark entails checking the contacts and the correctness of the gap between them, the conducting wires to the candle and the candle itself.
The way to check the spark is to unscrew the candle, connect a wire to it, put the candle sideways to the engine casing and pull the starter several times as if starting a petrol cutter, while looking at the coal and the contact of the candle, a spark should run between them.
If there is no spark, take a new candle, follow the same procedure, if the spark cannot be traced, then there is a problem in the wire or contacts, it is better to replace them.

The petrol cutter will not start or will start, but stalls. What is the reason?

To understand this, you need to know the principle of operation of the unit as a whole. It also happens that, just bought, a new saw does not start, and it starts running around the service centers, in such cases it is recommended:

  • Carefully read the instruction manual;
  • To study in detail the method of the first start-up and running-in of petrol cutters;
  • Try to understand how the product works;
  • How gasoline is pumped up and so on.

Reasons for malfunction of petrol cutters:

  • The quality of gasoline is poor;
  • Incorrect proportion of gasoline and oil;
  • Clogging of the fine filter;
  • The spark was gone.

The benzokos does not start on a cold

When starting a cold engine, it is not recommended to press the gas. Tilting the brushcutter so that the air filter is on top, press the fuel suction button 5-6 times, set the function switch lever to the start position, pull the starter cord several times until the engine starts. After a few seconds of running the motor, turn off the starting system.

The gasoline cutter won’t start after winter

In such cases, the unit must be serviced. Remove the fuel system, including filters (air, fuel), disassemble the carburetor, clean and rinse each unit. Blow out the filters with air. Pay attention to fuel quality and octane number.

It should be borne in mind that products of such well-known companies as STIHL, Husgvarna and other brands will not run on cheap gasoline with a low octane number.
Suitable fuel for them is from the AI ​​92 brand and above from car refueling stations and then from well-recommended ones, since there is also bad gasoline at refueling stations. The use of high-octane and high-quality gasoline will determine how long the brushcutter will be used and how long it will last.

It is necessary to take into account one more fact that with a long storage of a diluted fuel mixture, its working qualities fall, which also leads to consequences in which the petrol cutter will not start. Therefore, it should be diluted in portions, that is, the amount of the mixture that is produced at a time.
The operating instructions clearly describe and explain the mixing ratio of gasoline and oil. Strict observance of the correct proportions will at least save you from several questions about why the petrol cutter will not start and what to do in such cases.

The benzokos does not start when hot

If the brushcutter was recently in operation and has not yet had time to cool down but does not want to start, press the gas trigger, pull the starter cord sharply several times until the engine starts and only then the gas trigger is released. If enough time has passed and the brushcutter has managed to cool down, then it is necessary to start it as if it were cold.

The petrol cutter will not start, the spark is gone

The loss of a spark entails checking the contacts and the correctness of the gap between them, the conducting wires to the candle and the candle itself.
The way to check the spark is to unscrew the candle, connect a wire to it, put the candle sideways to the engine casing and pull the starter several times as if starting a petrol cutter, while looking at the coal and the contact of the candle, a spark should run between them.
If there is no spark, take a new candle, follow the same procedure, if the spark cannot be traced, then there is a problem in the wire or contacts, it is better to replace them.

The benzokos starts up and stalls. What to do?

1. There is a spark, and everything seems to be normal, but the petrol cutter will not start, in such cases, you should check the air access valve to the fuel tank. A clogged valve leads to the creation of a vacuum in the tank, in which the carburetor does not receive enough gasoline, so the petrol brush will start, but then stall. To exclude this reason, you need to clean the valve and try to start a petrol cutter with a tank cap that is not completely twisted.
2. If the brushcutter does not start at the same time, you should remove and clean the fuel filter, as well as check all the carburetor parts, and then try to start. The petrol cutter will not start again, the air filter is disconnected, try to start without it, if the mower starts up, the reason is in the air filter, replace it.

The benzokos does not start on a cold

When starting a cold engine, it is not recommended to press the gas. Tilting the brushcutter so that the air filter is on top, press the fuel suction button 5-6 times, set the function switch lever to the start position, pull the starter cord several times until the engine starts. After a few seconds of running the motor, turn off the starting system.

What could have broken

Problems with the petrol brush, due to the fact that this device does not start, are classified in a certain way by service specialists. They highlight faults with the following components of the mechanism:

  • An engine in which the piston and bearings may wear out or fail, crack the crankcase;
  • The fuel supply system, while the filter may be clogged or problems with the carburetor;
  • Mechanical damage to wires, tubes, hoses;
  • Ignition circuit.

At high revs

When the scythe stalls at high speeds, this is due to the following problems:

  • Clogging or sticking of the valve located on the gas tank cap;
  • The carburetor is out of alignment under the influence of vibrations arising during the operation of the mechanism;
  • Problems with the circulation of the fuel mixture;
  • Suction of atmospheric air;
  • The fuel intake hose is cracked or loose.

Adjust the carburetor according to the trimmer operating instructions. For adjustment, it is often sufficient to loosen the tightening of its housing. If there are problematic points with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its development, the engine stalls at high speeds.

Immediately after wound up

The unit may stall immediately after starting if the carburetor is misaligned or incorrectly adjusted, this causes an uneven fuel supply. The result of this is that the device vibrates distinctly. For troubleshooting, the carburetor is reconfigured, following the instructions for the mechanism.

Also, the engine stops when the fuel supply valve becomes clogged. In such cases, it is sufficient to simply clean it. If the brushcutter first worked, but then immediately stalled, then perhaps the fuel enters the carburetor unit with some difficulty. Weakening the valve helps to resolve the issue, which ensures free circulation of the mixture in the system.

The stoppage can also be caused by air leakage in the presence of mechanical damage to the hose (holes, cracks) that takes the fuel. In this case, add more revolutions to the drive in order to quickly expel air bubbles from the system.

Why does the petrol trimmer stall

A scythe with a gasoline drive is a useful thing for owners of home gardens, lawns, and when the trimmer suddenly stalls, the work to clear the area from grass stops. The device itself is a rather complex mechanism, so there are many different reasons for its breakdown. The most common problems are contained in the operating instructions. You should know the reasons why the trimmer stalls in order to effectively repair the device yourself.

When you press the gas

If, when you press the gas, the petrol cutter stops, then the reasons may be as follows.

  1. The most common variant is carburetor adjustment failure, which occurs when the drive is under significant stress, after prolonged inactivity of the mechanism, or when it is used in difficult conditions.
  2. Clogging of the fuel valve, which is eliminated by loosening it, as a result of which gasoline begins to flow normally through the system.
  3. Loosening and drooping of the cable in the carburetor. The fuel hose can also be stretched to the point of rupture due to significant stress.
  4. Clogged breather (non-return valve), as a result of which fuel does not flow into the tank.

If the problem is related to the carburetor unit, then it can be recognized by the appearance of vibrations of the brushcutter. When the hose bursts or the cable is stretched, these components are replaced.

Idle

At idle, common reasons for stopping the trimmer are as follows:

  • Dirt, misalignment or incorrectly adjusted carburetor adjustment;
  • Clogged air filter;

Replacing the air filter of brushcutters

Trimmer air filter

  • Reducing the speed of the gearbox when it heats up, which is a consequence of the use of an unsuitable fuel mixture;
  • Clogged throttle;
  • Air ingress into the system;
  • Not enough fuel to operate the petrol cutter.

Why the petrol cutter won’t start troubleshooting

Caring for the personal plot, summer residents periodically encounter the fact that the petrol cutter does not start. There are many reasons for tool failure. For the correct diagnosis of the problem, the owner of a useful unit in the country needs to know the device and the principle of operation of its individual parts.

  • How to start diagnostics of brushcutters
  • Checking the fuel mixture
  • We carry out diagnostics of a candle and a candle channel
  • Diagnostics of filters for petrol cutters
  • Breather and exhaust port
  • Complex reasons for the failure of petrol cutters
  • Rules for the operation and storage of petrol cutters

Breather and exhaust port

Often, delicate branded petrol brushes do not start and stall due to a dirty breather. The main function of this element is to equalize the pressure in the gas tank. When this unit becomes clogged, a vacuum is created in the tank, preventing the supply of fuel. You can eliminate the malfunction by cleaning the breather. You can use a regular needle for cleaning.

Normal operation of streamers with internal combustion engines can be disrupted due to dirt entering the exhaust channel or a clogged silencer mesh. There is such a problem on older generation models. The issue can be resolved by traditional cleaning and removal of the anti-spark grid.

How to start diagnostics of brushcutters

If the brushcutter does not start or immediately stalls after starting, it is necessary to sequentially check all the main components and assemblies. The verification algorithm is as follows:

  • Fuel tank (fuel quality);
  • Candle and candle channel;
  • Air filter;
  • Fuel filter;
  • Breather;
  • Outlet channel.

These nodes are most often the source of major problems that can be eliminated after a thorough inspection.

We carry out diagnostics of a candle and a candle channel

If the quality of the fuel mixture is not in doubt, and the brushcutter stalls when starting, then a flooded candle may be the cause. Here, for repairs, an ordinary candle wrench is suitable (every motorist probably has) and a spare candle.

  • We unscrew the candle and wipe it;
  • Dry it thoroughly (do not ignite);
  • We drain the excess fuel in the chamber through the spark plug hole and dry it;
  • We clean the old candle from carbon deposits using a file or a lady’s file;
  • We expose a gap with a distance of 1 mm (you can check with any coin);
  • We put everything back in place and try to start the trimmer.

If the candle is working, the socket where it is located is completely dry, and the petrol cutter does not want to start, lubricate the threaded connection with gasoline. It should be slightly damp. No matter how wonderful a spark the candle may give out, there is simply nothing to ignite in a dry chamber.

If the trimmer motor still does not start, you should exclude such a reason as the absence of a spark due to poor contact between the spark plugs and the high-voltage wire. If the connection is good and there is still no spark, most likely your ignition unit has flown. Here it will not be possible to do without a master, since the part is not repaired, but sold as a single unit.

Complex reasons for the failure of petrol cutters

If the step-by-step troubleshooting algorithm does not work, and your scythe still does not start or stalls, it is worth inspecting the carburetor and the engine itself. A clogged carburetor can be one of the reasons for erratic tool performance. There are three main problems here:

  • Clogged ducts or nozzles. All this is cleaned by special washes or blown by a powerful jet of compressed air from the compressor. Do not use needles and wires, as the bore may be damaged;
  • Worn carburetor gasket. Exit replacement of a failed gasket;
  • Violation of tightness. To check this indicator, you can use an ordinary household tonometer, replacing it with a suitable pressure gauge. Watch the readings: if they do not change everything is fine, but if the pressure starts to drop, then some part of the carburetor is faulty. We’ll have to find it and replace it with a new one.

If everything is in order with the carburetor, then the petrol trimmer may not start due to wear of the piston group. If chips, scratches or scuffs are found, the piston or cylinder should be replaced. Piston rings are subject to mandatory checks. A small backlash of the piston when rocking the connecting rod indicates that it is time to change the rings. It is best to entrust this procedure to the specialists of the service center.

Checking the fuel mixture

Before starting the engine of the gasoline streamer, check the presence and quality of the fuel mixture. Do not save, do not be greedy and do not be clever in this matter. Repair or replacement of the piston group will cost you too much (sometimes up to 70% of the cost of a new tool). Prepare the oil-fuel mixture strictly according to the instructions. Calculate its amount based on real needs. Excess gasoline left over after work loses its quality over time.