At what angle to cut the platband on the door.

Cashing on the door: the simplest method of cutting under 45 ° even without experience

Often during the repair you can encounter a situation where it is necessary to saw off a piece from the part, at an angle strictly 45 degrees. Usually, this is necessary to connect two parts at a right angle, 90 degrees, such as: door platoon, skirting, furniture and much more. An experienced master, professionally engaged in repair work, can often do without special devices, and almost by eye it is able to smoothly and clearly cut the necessary detail. But if you are a novice repairman, and you have a desire to make work as efficiently as possible, without damage to expensive details, then you just need to purchase a knock. a special device that allows you to saw off the material from a given angle without special tricks.

For work, you need to have: knock, hacksaw, a transport with a pencil, wood preparation, an electric screwdriver with screws or a clamp.

How to make a correct docking

If after gluing part of the baguette there is a certain distance to the corner, you must think about preventing a mistake. a small stock will not hurt. First, it is better to cut off a piece with a good margin of about 10-15 cm. Then, cutting off the angle with any convenient method, make it fitting on a dry surface. To do this, you should put the bar to the ceiling and mark the point where the border of shortening will pass. We perform cutting at right angles.

A competent coat of angles is no less important. Ready skirting boards are usually fixed at an angle, slightly smaller than 45 degrees, so inconsistencies of cut edges and the appearance of gaps are possible. Here, the primary pruning of the corners follows dry, if possible, the exact docking of the skirting boards is already on the ceiling itself. Problems usually arise when using wooden and plastic materials.

At the end of the rough joints of the fillets, they should be glued or fastened, and then, if necessary, use the help of putty and then to seal all available seams.

Ways to cut the platband under 45 degrees without resorting to the use of

The easiest way is to use an ordinary transporter, which is in every home where a school age child lives. With his help, making markings is not so difficult.

Important: it is important and drank it itself. To avoid the formation of cracks, it is recommended to use a hacksaw not on wood, but in metal. Yes, this method requires more time, but for that, the gap will be much more accurate and even more.

When the marking using the transporter is made, you need to place the platband on the horizontal surface so that the front side is at the top. It is recommended to make a cut along the entire platform of the platband.

If there are no office devices nearby, you can use ordinary tiles, with which you can draw an angle of 90 hundred degrees. Dividing it into 2 halves, we will get a template for a 45-degree angle, which can be used for marking instead.

If there is a ruler, the task is simplified several times at once. You just need to take the A-4 leaflet and draw a square, and then draw a corner bisector. To make it more convenient, you can take a small board and attach it to one of the corners, which will fix the structure. Well, then you need to attach the platband and start sawing.

How to make a knock at home?

If the above methods did not like it, you can make a knock at home on your own. Knock-a device resembling its shape, which has a P-shaped shape.

It is equipped with cuts for saws designed for sawing the material at a certain angle. The dimensions of the details are not very important, but the wider our home.made device, the wider and more precisely we will be able to saw wide racks.

Important: everything needs to be done wisely, it is also not worth overdoing, because if the width of the risen exceeds half the width of the hacksaw, it will be inconvenient to saw.

You can make markings resorting to the above methods, and then use small pieces of plywood and hacksaw. And in order to fasten everything, you can use self.tapping screws or even super glue. However, all this is more complicated and will take much more time, although it will provide the most accurate result (of course, if you do everything right).

Of course, this is a convenient and practical tool. It is sold in almost any construction store and has a low price, which absolutely everyone can pull.

However, if for some reason the situation has developed that it is impossible to get the tool as soon as possible-you can use improvised tools, such as a ruler, transporter or even tiles, with which it is easy to create a template with the desired marking or completely recreate a knock at home.

Conditions for replacing and returning low.quality products

What to do if the consumer bought a product from us, which does not suit him on any signs: design, size, configuration, etc.? The purchased goods were not operated, consumer parameters remained in its original state, the presentation did not deteriorate, the packaging was not damaged? In such a situation, within a two.week period, you can apply to the sale point and submit an application with a request to exchange the goods for a similar option or return the money, provided that the desired model is not available. Expenses associated with the delivery of goods for exchange, and the organization itself, the buyer takes on.

In this case, you can use the usual school transporter. With it, it is easy to measure the corners. However, the transporter may not be at hand if there are no schoolchildren in the house. In this case, the usual tile will help out, with which the strip at right angles is drawn, after which it is divided in half. The cut is best done on the front side, working with a hacksaw on the entire plane.

You can also use a regular line for marking. risks will turn out much more accurately than using tiles.

Necessary tools

To properly and carefully carry out this procedure, you will need:

• Flow. Do not know how to cut the platband at an angle of 45 degrees. with its help. It helps cut the product at the right angle. Can be wooden, plastic, metal. Outwardly resembles a box.
• Hacksaw. For metal, plastic, a hacksaw for metal is suitable, for wood. only on wood. You need to correctly sharpen it so that the cut turns out to be even.
• Nails/liquid nails.

If you can’t use a knock, then you can do with improvised materials: pencil, ruler, cardboard, hacksaw.

Liquid Nails

Another method of attaching platbands involves the introduction of special glue. The most popular option is the so.called watery nails. This composition provides brisk adhesion in fact with at least some surface.

Let’s see how to correctly fix the platbands without ordinary carnations. To do this, first you need to find a clear position of each element. Then apply a small amount of glue to the back of the bar and press it to the wall. If glue has appeared from under the platband, immediately wipe it. It is better to apply only a few points to prevent spreading.

Fastening platbands on watery nails simplify the process

How to correctly saw off the platbands on the door with your own hands: Instructions and videos

Many, setting the door, wondered how to cut the platbands. It would seem that this is a complex. Since not everyone is able to cut the platbands evenly, it is worth studying the main methods. When cutting, a knock, transportation, improvised materials are used. You can cut them in two ways. under 45 and at 90 degrees.

The necessary tools for drank platbands

To properly and carefully carry out this procedure, you will need:

• Flow. Do not know how to cut the platband at an angle of 45 degrees. with its help. It helps cut the product at the right angle. Can be wooden, plastic, metal. Outwardly resembles a box.
• Hacksaw. For metal, plastic, a hacksaw for metal is suitable, for wood. only on wood. You need to correctly sharpen it so that the cut turns out to be even.
• Nails/liquid nails.

If you can’t use a knock, then you can do with improvised materials: pencil, ruler, cardboard, hacksaw.

How to cut the platband with a bunker

The main advantage of the struck. it was marked in advance angles. Due to this, performing manipulations is not so difficult.

Cocking the platbands along the rushed lines can be as follows:

The slots are quickly shaken under the influence of the saw, so this is a one.time tool, but the price will allow you to stock up for the future.

How to cut the platbands yourself without the help of the stir

How to cut a platband on the door without using specialized equipment is a question that excites many newcomers in the construction business. It is more difficult to do this, but perhaps if you carefully follow the instructions:

• Take a sheet of cardboard, draw a flat square, draw diagonals, bring the sides of the square to the end of the side of the sheet. This is an impromptu ceiling suitable for washing a straight angle.
• Attach the platband to the bottom line of the square and saw with a hacksaw where one of the diagonals crosses it. This is the lower border.
• Put the other to the left side of the square, cut at the place of touch the same diagonal.
• Do paragraph 2 and 3 for the upper and right platband.

How to correctly saw off the platbands on the door at home at the steps

Tips and recommendations

Before installing the door, leave the wallpaper supply in case the gaps remain after the installation. the small ones are easily masked by them. To make the opening look better, it is recommended to choose special nails with a small hat. The hammer is also used small in size so as not to damage the lining. Cloves are covered with mastic in tone.

Cutting in place. applying the platband to the doorway, floor or wall. This is not the best option, because walls and floor are never perfectly even. The error that appears with this approach is great.

To cut the platband, the transporter is also used. the corners are already drawn on it.

Advice! Not always installation of planks is needed. It is unacceptable for rooms with tiles. better use the plaster.

Installation of platbands. a mandatory stage in the design of the doorway. The right choice can even delay the door installation time, because the view will be good.

Types of platbands and tools for their installation

To frame doors, you can use different types of platbands that differ both in terms of manufacturing and in their form. Material for platbands most often serves wood (whole or fraught) or plastic. Steel or aluminum platbands are produced, as well as from plywood or laminate.

The shape of the platbands can be flat, rounded and curly. Flat. the simplest and most democratic, they will not be striking in any interior. Rounded are different from flat in that they have a rounded frontal part, which gives them unusualness and some sophistication. The most beautiful are curly ones that are mainly made to order.

But all this variety of types of platbands can be divided into two large groups. The first includes platbands that have the shape of a rectangle in the end. Their advantage is that they can simply be jointed, without making angles in 45º.

The second group is platbands that have a semicircular or figure section on the end. Such forms look wonderful, but when installing intoleaned or cut carelessly, their central part will protrude above the lower end, which will immediately be striking. Therefore, their trimming is strictly at an angle of 45º is required.

To install the platbands on the door, you will need a tool:

Cutting with improvised means

Do not always need to perform a large amount of work. Why spend money if you need to cut off a few tiles. In this case, you can use the following tools:

Important! It is recommended to use a drill with a winning attack. Thanks to it, you can give a deeper scratch to the surface of ceramics better

How to cut with glass cutter with ceramic tiles? The algorithm of actions is this:

An extra fragment is measured. Marking is applied on it. A metal line is superimposed along the fishing line

It is important to do it perfectly evenly. It remains to have a one.time with glass cutter or other sharp improvised material vodollineye. In the process, the ruler should be well held

As a result, you get a noticeable scratch. The tile is located on the edge of the table or workbench. Scratch on it should coincide with the edge line of the table. A strong, confident and sharp movement of the hand should be pressed on the edge of the tile.

The desired piece will break out. It is clear that making a cut perfectly will not work. But you can save money. And after that, just wipe the cut with sandpaper. In addition, if you put tiles in clean water for only an hour, then the cutting process will become better.

note! Some ask whether it is possible to cut ceramic tiles with a jigsaw. Yes, but the cut will not work as high quality as I would like

The use of an electric jigsaw is rational when adjusting the tiles laid in an inconspicuous place. But, there are special saws with diamond spraying for manual or electric jigsaw. This option is allowed.

Figure breakdown

Sometimes you need to make curves of a mowing fishing line. Kosilian fishing line can be not only straight, but also semicircular. Such breaks are more problematic when they do not start from the edge. In such cases, you will have to first make a hole and then break out of it.

For curly breakdown, it is recommended (if possible) in any way to apply deep risks of the breakdown. This will reduce the number of possible chips.

There is a special tool for breaking off. tweezers with a wheel. But for one.time work to purchase a special tool is inappropriate. Therefore, you can do with ordinary pliers.

Breathing technology is very simple. Plafers (or forceps) are strongly compressed, the material is crumbled, or compressed and sharply rotated (only far from the braid fishing line, at least 5 mm). Small pieces are broken off. When trying to break off a large piece at once, you can ruin all the work. Part may break off the risks.

Long, straight, narrow pieces through all tiles are broken off by a sharp turn of the pliers to the side. Previously holding them on a mowing fishing line risks (scratch, of course, should be applied). In this case, the tiles may not break off for the entire length and the procedure will have to be repeated on the rest. Then they also carefully break the remaining sharp ledges.

The easiest way is to apply risks and a blow to an acute angle. In this way you can easily and quickly prepare most of the elements.

Two ways to drink cashes, easily and simply!

Hello, dear friends! In this article I will tell you and show you how easily you can cut out cashes at 90 degrees, for door decoration or something else. Interesting, then let’s go!

Hacksaw (preferably with a small tooth, the cut will turn out to be thin and neat)

The first method using the end saw.

I divided our cashing out for example, into equal 4 parts of 30 cm. Put one segment on the end table of the end, turned on the laser fishing line for a trimmer, turned the saw 45 degrees and made a washed. With the second segment, I do the same, but I put the saw 135 degrees and make it, I am ready.

The second method of washing without the help of the end saw.

I think this method will be more interesting for you, since not everyone has a end. Until some time I had no time, I coped with a bang! So we take the two segments of our caster (it is advisable to reduce them in advance by marking them with a square), lay them on each other and combine them on the sides and in the corner, so that everything is exactly the smoothness of our Wall. Put, combined and mark with a pencil

Next, take our square and draw a flat fishing line for a trimmer from the corner to the mark

All the markup is ready, the floor is in the hat! Now we take a hacksaw with a small tooth (I once sawed the metal with a hacksaw, tired of course, but the cut was so clean), and slowly we make an incision along our line, keep everything tightly, and then the hacksaw will play and you can leave the bullying. We try to saw at an angle as acute as possible, the cut will be smoother.

We sawed off, now we do the same with the second segment. We combine two segments into a single corner and rejoice at the seen! So easy and simple, without ending, you can make an angle of 90 degrees. Thank you for your attention, successful repairs and until new meetings!

How to cut the corners in platbands using

We talked about cutting tools above, and now we will discuss the process of cutting angles itself. The latter in the case of platbands are 45 degrees, and try to cut them by eye without appropriate experience is not worth. But this is not necessary, since there is an excellent tool for this tool.

We are talking about such an element as a muffle. It has the shape of a tray made of wood or plastic, in which grooves are made at different angles, greatly simplifying the work. After you cut off the desired platform length, just attach it to the inner wall of the stir and, choosing a hole with the right angle, saw off the excess. You do the same with the rest of the fitting elements, then apply them to each other to verify the absence of gaps.

How to cut the corners in platbands using

We talked about cutting tools above, and now we will discuss the process of cutting angles itself. The latter in the case of platbands are 45 degrees, and try to cut them by eye without appropriate experience is not worth. But this is not necessary, since there is an excellent tool for this tool.

We are talking about such an element as a muffle. It has the shape of a tray made of wood or plastic, in which grooves are made at different angles, greatly simplifying the work. After you cut off the desired platform length, just attach it to the inner wall of the stir and, choosing a hole with the right angle, saw off the excess. You do the same with the rest of the fitting elements, then apply them to each other to verify the absence of gaps.

Secrets of installing platbands on the door with your own hands

Platbands play a decorative role, giving the doorway the completed look. The bar is different with the material of manufacture, shape, color, as well as the method of fastening. The platforms of the interior doors are installed after the end of the wall decoration, but before laying the floor skirting board.

To correctly install platbands on interior doors, first you need to choose the right elements. First of all, they pay attention to the material of manufacture:

• Natural wood products are considered universal. Glane can be painted to the color of the doors. Fasten wooden elements with nails without hats. If the walls are well leveled with a door frame, platbands are planted on an adhesive. “liquid nails”.
• Laminated trims made of wood.fiber slab with appearance resemble natural wood. Decorative elements are selected to the color of the door. Fasteners are attached with adhesive composition or nails without hats, having previously flinged the undersized holes.

Most strips give a standard flat, rounded or figure shape.

By the method of fastening cashing, there is an overhead or telescopic. The first type of elements is fixed directly to the door frame. Second. equipped with installation grooves.

Little tricks

When choosing wooden platbands, you should pay attention to the quality of the drying of the board. Poorly dried wood:

In order not to spoil the workpiece, the length of the cashing length should be performed with a margin of at least 1 cm, which is useful when combing the angles of the connected parts.

Cut off excesses easier from the opposite end of the bar.

Do not use a moisture.resistant marker for marking on the front side. Removing the drawn lines with ordinary erasure will be hard.

Carriage of platbands is best done with an end electric saw.

It will provide a clean cut without chips. Neatly adjust the cut corners easier than a tape grinding machine. With its help, you can achieve perfect combustion in the corners.

If gaps formed when installing the platbands on the door, they can be made almost invisible, using a mixture based on bee wax, which is purchased in a construction supermarket.

Heated and brought to a state of plastic mass, it will perfectly fill the resulting cracks.

Visually, cashing, towering above the doorway by 10 centimeters, and the unified style of the premises in the apartment will provide the same platbands on all doors.

Several practical tips

Naize the first nail in the middle of the platband, this will turn it a little for a tight connection in the corners of washed down. Only after the corners fell on the doors from all sides, you can drive out nails for their fixation. The distance between the nails is approximately 15 ÷ 20 centimeters. Check the distance with light tapping by the platband. You will immediately find out in which places there is a loose fit of the platband, drive additional cloves into them.

If during the clogging the nail did not come to the end and bent. do not pull it out. Gently clamp the rest of the pliers, rotate it left/right until it breaks. Why not pull out? The nail could not clog along the “good” reason without dependent on you, this means that the second one will not enter this place to the end. It is much better to score a new one at once, fewer holes will be in platbands.

You can increase the adjacence of the adjacent platforms over the entire width with mounting foam. Apply it on the back of the platbands with a thin strip along the entire length from the side of the wall, give three to four minutes for a partial drying out. Otherwise, the foam will not stick to the surface. Next, arrive platforms in the recommended way. After the installation foam completely dried up, carefully cut the visible part, the gap can be closed with sealant. Although, if you do not overdo it with foam, then it should not speak. During pressing, the ability of foam to increase volume is significantly reduced.

Let’s give practical tips on working with a pneumatic gun. It is arranged in such a way that there are holes for the air exhaust from the side. The piston is constantly lubricated with machine oil, during the exhaust of the air, its smallest particles come out. Когда шпильки нужно вбивать в торец наличников, на белой стене всегда образуется маслянистое пятно от выходящего воздуха. Be sure to put clean paper between the gun and the wall.

Pneumatic pistol for Makita Af505 nails

If you have a white platbands. do not lubricate the nails with oil, the oil will leave the spot at the entrance to the entrance.