Bucharda for a grinder what to do. How to use a puner to use bouchard

All about the Buchards. What is it, species, purpose and application

Hearing the name Buchard, an association with a culinary dish arises. However, this is not a dish at all, but a specialized tool with a narrow purpose. Structurally manual Bucharda resembles a locksmith hammer. The difference lies in the presence of protrusions, due to which useful work is performed by the tool. What is Buchard, and what types are, far from many people know. It is about manual and Buchard for the perforator that will be discussed in the material.

Bucharda is called a hand tool that has the appearance of an ordinary hammer, on the working surface of which there are teeth. Teeth have the shape of pyramids, and the base of the steel tool is made. A tool for processing concrete, stone and plaster surfaces is intended. Bucharda are treated flat surfaces in order to give them roughness. The process of giving the surface of roughness is called boocarding.

The tool in question is not popular, and it is often used by sculptors or repairmen who are engaged in finishing work. Through this tool, it is possible to solve a number of the following problems:

• To remove concrete protrusions, for example, when the concrete base is poured, after removing the formwork, bulges remain. To remove these protrusions, a specialized tool is used. Bucharda
• Giving roughness to smooth surfaces, which positively affects the quality of adhesion. This is done so that the finished smooth surfaces, for example, the steps, do not slip. In addition, after the booudration procedure, you can provide a reliable connection of marble or granite plates
• Preparing the surface of the walls for finishing processing. Bucharding allows you to remove old paint from the surface, thereby preparing the basis for further work
• Creation of notches based on further laying of ceramic tiles and tiles. The laid tile on the floor or wall is better grasped if the surface is rough at the same time
• Giving smooth surfaces of decorative roughness. Usually such roughness is performed on granite and marble
• Removing corrosion plaque from the surface of the metal. It will not work to clean the material completely from corrosion, but to produce primary processing is quite real. After the primary cleaning of the metal surface, metal brushes with grinder for finishing processing are used

To achieve the necessary result, on the processed surface, strikes with different power and intensity are caused. The principle of operation of the tool is simple, and it is based on the riding of concrete particles, thereby the surface from glossy turns into a matte.

It is interesting! Structurally manual bucharda has the shape of a hammer with two surfaces. Teeth or protrusions are not only pyramidal, but also conical shape obtained by casting.

Diamond disk for grinder for cutting tiles/stone

These are excellent cutting nozzles if you look at the price-quality ratio.

Sitting place-22.23 mm, disk diameters-105, 115 and 125 mm, thickness 1.1-1.6 mm.

They cut quickly and without chips, suitable for tiles, marble and granite. I want to remind you that it is strictly forbidden to use cutting circles of larger diameter than those indicated in the passport of the grinder. By the number of maximum revolutions, the cut.Out circle must also correspond to the passport data of Ushm.

Pendulum saw

The accuracy of high.Speed cutting of different materials and at the required angle is provided by a special device called a pendulum saw. At home, it can be made from a grinder with a capacity of 0.9 to 2.5 kW, having thought out a design that directly depends on the model of the Ushm. All that needs to be done is to make a metal platform with a slot, a corner, a pendulum and securely fix the tool itself on it. To do this, use holes for installing a handle on the grinder itself. Under their size, it is necessary to make a bracket, stripes, studs and bearings, with which to fix a grinder in the working position. Ushm device is ready.

Pneumatic Bucharda is what is pneumatic buchard?

Universal Russian-English dictionary. Academician.RU. 2011.

Watch what is “pneumatic buchard” in other dictionaries:

Pneumatic (electric) bouchard. Pneumatic (electric) manual machine for cleaning and processing stone and concrete surfaces. [GOST 16436 70] The themes of the machine manual pneumatic and electric En Piston Scaler de Klopfer Technical Translator Handbook

Pneumatic (electric) bouchard. 60. Pneumatic (electric) boucard d. Klopfer E. Piston Scaler Source: GOST 16436 70: Machines manual pneumatic and electric. Terms and definitions Dictionary and reference point of the terms of regulatory and technical documentation

GOST 16436-70: manual pneumatic and electrical machines. Terms and Definitions. Terminology GOST 16436 70: manual pneumatic and electric cars. Terms and definitions of the original document: 42. Cutting pneumatic (electric) manual scissors D. Knabber E. Portable Nibbler F. Grignoteuse determination of the term from a dictionary-reference point of the terms of regulatory and technical documentation

Hand cars. A mechanized tool, a group of technological machines with built.In engines, with which their weight is fully or partially perceived by the hands of the operator that supplies and control the machine. R. M. Usually weighs from 1.5 Big Soviet Encyclopedia

Varieties of the tool

There are several types of products, which allows you to choose the best option for any budget.

Manual

As already mentioned, manual Bucharda looks like a regular hammer, but with two working parts and a surface with teeth. Some manufacturers into ledges interspers artificial diamonds. This increases the strength of the product and its effectiveness.

Manual bouchard has different dimensions, the number of teeth. The price of the tool is in the range from 1,000 to 10,000 rubles.

Mechanical

Depending on its type, the following models are distinguished:

Pneumatic device

The product functions from compressed air. The principle of action resembles a perforator. However, unlike this tool, Buchard is equipped with a compressor of lower power. The surface using the device is processed mainly due to its own weight of the device.

The case of the product practically does not heat up, which allows us to operate for a long period. The device is characterized by ease of use, high efficiency.

Typically, the kit includes several nozzles, which allows you to choose the best option for different types of work. The weight of the product is from 6 kg, the price is from 10,000 rubles.

Electric device

Such a tool on the principle of action resembles a grinder. The only difference is that instead of a disk, appropriate nozzles are used here. The tool works from electricity. Differs in the convenience of operation, durability, high efficiency. Disadvantage. High cost from 50,000 rubles.

Bucharding machines

Instrument used in production. It is not suitable for use at home. The product is highly powerful. Allows you to do a large amount of work without interruptions.

Nozzles

To perform a surface boiler, it is not necessary to purchase a special tool.

To carry out appropriate manipulations, you can buy special nozzles for certain devices:

This is a high.Power tool, which allows you to quickly perform appropriate manipulations. On the market there are nozzles with two types of tails. SDS Plus and SDS Max, which are selected, depending on the type of assembly of the device.

Such nozzles are practically no different from the previous option. In this case, the type of tail is also selected for the type of tool cartridge.

It is a special disk to perform boots. It is thanks to such a nozzle that even ordinary grinder can be used to carry out appropriate manipulations. This allows you to save on the purchase of a power tool and not lose in efficiency.

Pneumatic boucharda when used and what is pneumatic bouqueting

In addition to nozzles for a perforator, buchhards are also pneumatic. This type of tool is popular among professionals. The principle of operation of the device is based on turning the energy of compressed air into reciprocating movements of the working elements of a pneumatic tool. Such devices work from the compressor, and not only from powerful.

With prolonged use, pneumatic buchhards do not heat up, which is their main advantage. In addition, they weigh less than perforators and chipping hammers, which positively affects their operation. The second important advantage of the pneumobucard is the simplicity of their device. When breaking the tool, just fix it with your own hands. With wear of the working part, it is necessary to replace the bats. For the manufacture of the working part of the pneumobucard, tungsten carbide is used. The resource bit for the pneumatic tool is 500 m2, but when processing reinforced concrete, this resource is reduced.

How to work correctly with a pneumatic bouquet shown in the video below.

It is interesting!To increase the resource of nozzles-Buchard, manufacturers are covered with winning attacks.

Recommendations:

Bucharding. A special type of texture used by builders since time immemorial. Gives an aesthetic and interesting appearance to surfaces made of natural and artificial stones, creates a unique color game on crystalline materials. Therefore, “Bucharda“, as additional textured stone processing, is often in demand by designers both inside and outside the rooms. The surface can be processed (exacerbated) in whole or in part. According to the templates.

Buchading is also an excellent solution for the fight against slippery steps and sites. When installing straight or patterning guides, a boucaric nozzle will help to make beautiful strips of anti.Excess with a clear contour. Such stripes are not erased over time and “work” in any weather for pedestrians safety. It should be noted that, in contrast to heat treatment (firing), boocation can be done on almost any stone (including already laid), while spending a much less time and effort.

At the moment, there are two types of boocaries: manual and mechanical. Mechanical, in turn, is divided into shock and using rotating tools. The processing principle is the same. Many strokes of carbide teeth create chips on the surface. The manual method is more accurate and gentle, and the mechanical method is less labor and more massive. The number of teeth on the shock nozzle affects the degree of roughness of the product. Basically, for natural stone and concrete, three gradations of boocharding are used. Fine, Medium, Coarse (small, medium and rude).

Information about promotions and special offers request from managers!

DIR.Made grinder devices

Choosing material for the bed

To cut metal, wooden, plastic sheets of large sizes, you should install a grinder on a moving carriage moving along the guides. It is advisable to use metal corners as guides of this case.

A stand for a corner grinding machine can have many options for execution. For its manufacture, a variety of materials and nodes can be used. It makes no sense to recommend a specific design, since each Ushma owner will adapt the grinder to his requirements.

You can use profiled pipes as the source materials for the device, as the most durable and reliable for this type of work. For guides, you can use corners, channel 5U or 6.5u.

For complex designs, you will need a welding machine, but it is easier to do with screw connections. If work does not require special accuracy, then the grinder can be used simply as a portable tool.

To carry out accurate work, for example, with a grinding nozzle, you may need a stationary device. A stand for the Ushm grinder (with your own hands you can assemble a simple collapsible machine, which will be composed and hidden in the allotted place after use). Such a bed is sometimes also made of wood. It is advisable to make a wooden bed if the frequent and prolonged use of Ushm is not supposed to.

Flowing from a grinder

If the countertop under the corner grinder perform a rotary, you get a great knock. Using such a device, you can quickly cut at a fixed angle the baseboard, baguette, profile from any material.

It is only worth installing the appropriate disk, fix the countertop at an angle of 45 degrees. And the cutting of the platbands for the Windows of a wooden house turns into pleasure.

Such a machine can easily cut the paving slabs diagonally, diversifying the ways of laying it.

Something similar is produced in the industrial version, but the cost of such devices will scare away not only the home master. But also a small team of locksmiths.

What may be needed for the manufacture of a bed

Before you start making a bed for a grinder, you should decide what types of work this machine will perform. Ushm stand, made with your own hands, can be much more functional than industrial products. Of great importance is the type of ushma mount on the bed. Vertical or horizontal. The cutting depth largely depends on this. The type of fastening also depends on the nature of the work performed.

For cutting materials on a stationary desktop, the Bulgarian is attached to the pendulum bracket from corners or profiled pipes. If it is necessary to cut large sheets of steel, textolite, plywood, then Ushma is attached on a movable carriage moving along guides made of corners or channels. Having decided on the design, you should prepare the necessary tools and materials in advance.

• Bulgarian;
• Drilling machine;
• Welding machine;
• Grinding wheel;
• Pliers;
• Screwdriver Set;
• Keys set;
• Measuring tools.
• Steel corner 40 × 40;
• Steel corner 50 × 50;
• Channel 5u or 6.5U (for guides of a moving carriage);
• Trimming of water pipes;
• Profile pipes 15 × 15, 20 × 20, 25 × 25;
• Bearings;
• Metizes;
• Tin trough;
• Textile.

Nozzle for connecting to a vacuum cleaner

This simple device will help you protect your breathing organs from dust during cutting wood, metal and other materials. The nozzle is installed on the cutting part of the grinder, closing it completely. A special pipe provides a connection to the vacuum cleaner hose, which allows you to remove dust quickly and efficiently.

Thanks to a special design, the device provides 99% of dust removal. The nozzle is easy to install and compatible with most power tools. The transparent case provides good visibility of the working area. This device supports the adjustment of the cut depth.

How to make a simple stance for the ear with your own hands

With the help of the most ordinary tools and using improvised materials, a simple Ushm stand can be made with your own hands. To fix the grinder on the bed, you will need corners, metal or textolite plates. If two metal plates are used, then you can replace the screws with a welded connection. The plate serves as a mobile platform is made of steel sheet or duralumin with a thickness of up to five millimeters.

If you use textolite instead of a metal sheet, then the workpiece should be up to ten millimeters thick. The second plate must be metal, as it serves as an emphasis. For manufacture, steel is used five millimeters thick, since the main load is applied precisely on it. You can not use thinner metal due to vibrations and possible deformation, which makes work with the device unsafe.

For reliable fixation on the platform, several through holes with a diameter of five millimeters are drilled on one half of the plate. The second half of the plate is marked so that then in the center it drill a hole with a diameter of eight millimeters. All holes drilled in the platform are drilled on the back of the hidden screw heads. It is allowed to put a corner instead of the second plate, drilling it accordingly.

If the welding cannot be used, the corner or plate is firmly attached to the platform so that the distance from the edge of the device to the detachment of the disk is at least five millimeters. In this case, the corner should be bent in relation to the rack of 60 °. To exclude the turning of the bolt and vibration of Ushma, it is fixed in the upper part with a bolt with a puck of a grover or a counter.

Assembly procedure for a grinder

Preparation of the platform from the duralumin plate. ✓ Cut the plate size 300 × 120 mm.

✓ Six Ø4 mm holes with a deepening under the hats of self.Tapping screws. These holes are needed to attach corners, bar and handles. ✓ from the duralumin corner 30 × 30 × 420 mm make an angle.

To do this, make a cutout in the form of an equilateral triangle in one of the shelves in order to bend it at a right angle of 90º. ✓ Drinkly fasten the handle (120 × 60 × 23 mm) with bar (270 × 28 × 35 mm) using screws 3 × 35 mm. 2 pcs.

✓ Reciprocated M-shaped details and a duralumin plate we collect together. Everything is attached with screws 3 × 20 mm. 4 pcs. The base of the device is ready. Final assembly of the device for a grinder ✓ Treasury must install metal corners 55 × 30 × 75 mm. 1 pcs. 60 × 60 × 45 mm. 1 pc. On the received platform for attaching a grinder. Pay attention to the corner of 60 × 60 × 45 mm must be bent a little from 90º to 60º.

Otherwise, do not fix the grinder. The grinder is attached to the corners on one side using its own handle, and on the other hand, using a bolt with a counter.Thaw m 8 × 20 mm.

Ruthagica is necessary so that the bolt does not unscrew on time of work.

Ruthagica handle is not needed, t.To. You hold it with your hand.

That’s all. A device for cutting a grinder is ready. I think that many will have a reasonable question: “Why do such a device when there is a manual electrical disk saw?”” I agree with such a question, but if you often use such an electric saw, then you can purchase. And when from case to case, it is better to have such a device. By the way, such a device can be used not only, for example, to shorten the doors, but also for work with ceramic tiles or with plastic panels. It is only necessary to change the cutting disk.

This article is all. There will be questions, contact the feedback form (blue button on the left) or through the “Contacts” page. Somehow later I will write about how to make a small sawing machine from an electric jigsaw. So subscribe to the site news is free. You can also read more articles.

What is Bucharda in construction?

Not only to simplify the work, but also to accelerate their conduct, manufacturers produce not only manual boucars. To accelerate and simplify work, manufacturers produce boots for a perforator. This is a type of nozzle for a perforator, which allows you to expand the functionality of the tool. Why the nozzle was made for a perforator? Since it is this electrical tool that has a jack of chipping hammer.

Buchard’s nozzle for a perforator constructively consists of two parts. Working and fasteners. The working part has a similar design with a manual tool, and the fastener is presented in the form of a shank for fixing in a perforator cartridge. Manufacturers produce nozzles for perforators with two shanks. SDS Plus and SDS Max.

A distinctive feature of nozzles-butuchards for a perforator with SDS Max and SDS Plus Salaries is an equal number of cone-shaped protrusions, which are 16 teeth. These 16 teeth are located in a row 4 by 4. Bucharda size for a perforator with a number of teeth 16 pieces is 48×48 mm. There are nozzles for a perforator with a smaller and large number of teeth, however, the most popular are precisely 16-green devices. The nozzles with 9 teeth provide more rough surface treatment, and with 25 links allow you to give the surface of the light roughness. Varieties of nozzles Buchard for a perforator are presented in the photo below.

Like any type of tool, nozzles have an appropriate operational resource, which is equal to the processing of a section of 1000 m2. After working out such a resource, the quality of work worsens due. The teeth are not subject to sharpening, therefore, when the resource declared by the manufacturer is developed, the nozzle should be replaced.

It is interesting! Nozzles for the driving punch are whole.Lit with sDS tailings or detachable (collapsible). The second option will cost cheaper, and its main advantage in the possibility of replacing nozzles with a different number of teeth.

It is possible to work with a bucharda on a perforator on concrete or granite exclusively in shock mode. A jackhammer. If you enable the rotation mode, this will lead to the Rapid wear of the teeth, as well as the injury to the operator. How much does a boucard cost to a perforator. Masters ask this question, choosing between a nozzle and a manual tool. The nozzle costs from 1000-1500 rubles, which depends on the manufacturer, quality and number of teeth. In addition, SDS Max’s nozzles are more expensive than SDS Plus. Manual bouchard costs about the same that it depends on the type of handle. Wooden or metal.

Excerpt characterizing boucaring

And both friends told each other. One about their hussar wrappers and military life, the other about the pleasantness and benefits of service under the command of high.Ranking persons and t. P About the guard! Said Rostov But what, went for wine. Boris grimaced. “If you certainly want,” he said. And, going to the bed, he took out a wallet from under clean pillows and ordered to bring wine. “Yes, and give you money and a letter,” he added. Rostov took a letter and, throwing money on the sofa, leaned on the table with both hands and began to read. He read a few lines and looked angrily at the berg. Having met his gaze, Rostov covered his face with a letter. “However, they sent you a decent money,” said Berg, looking at a heavy wallet, clinging to the sofa Here we are and a salary, count, break through. I will tell you to myself “That’s what is my dear Berg,” said Rostov, “when you get a letter from home and meet your person, whom you will want to ask about everything, and I will be here, I will leave now, so as not interfere with you. Listen, please leave somewhere, somewhere to the hell! He shouted and immediately, grabbing his shoulder and gently looking into his face, apparently trying to soften the rudeness of his words, added:. You know, do not be angry; Dear, darling, I say from the bottom of my heart, as our old acquaintance. “Ah, have mercy, Count, I really understand,” said Berg, getting up and speaking in his throat voice. “You will go to the owners: they called you,” Boris added.

Today we will consider what granite boocaries are. The word is what you say, but about everything in order. What answer to us Wikipedia gives us.

Bucharding. Processing surfaces made of concrete, reinforced concrete, natural stone, etc. Materials to give the necessary roughness that prevents sliding, or to remove the upper layer of worn material using a carbide tool in the form of stars. Subsequent grinding with diamond cutters and polymer protective compounds are possible. The term came from FR. Boucharde, which literally means a metal tetrahedral hammer, two shock surfaces of which are covered with pyramidal teeth.

From the description of this term, you realized that this is a special processing process.

First, we will heat the coating. And with the help of a burner granite, roughness will return, though the paint will become dull, but this should be sacrificed so that the legs do not slide in the future. You only need to decide to process the steps completely or only the edges.

And then just Start and make a boocarlation procedure. Special grinding machines with disks come to the rescue here. Translated from Italian, Buchard means a hammer for stone. This is a special tool that is ideal for opening the crumbs in concrete floors, applying strips against slipping and removing old coatings. And this is thanks to two details: there is a tool of two plates, and shock absorbers are between them. Depending on the purpose that is pursued, 2 types of milling elements are represented by the company. The milling can be performed as an intermediate phase before grinding with diamond discs, thanks to which the surface becomes even and flat. During the boots, the drums are spinning, tapping at granite and removing polishing. You will naturally have a question now: how is beauty? So, in order not to bring the stone to the asphalt color, the burchanding can be made with stripes with a width of about 45 to 75 mm.

Sometimes, to avoid slipping, you can also apply this technique: knock out stripes on the steps, t.E. Make engraving, using the disks installed on the machine, are made along the edge of the steps of the cut. The surface is embossed, and walking along it becomes safer. And if rubber gaskets are also placed in the cuts, then there will be practically no sliding.

Therefore, now you understand what granite boocaries are, and ordering certain services or products from us, you will have an idea about it, and understand how much this service is necessary for you.

Pneumatic tools. Industrial model

The construction of multi.Storey buildings is usually large volumes of concrete work. Although the usual perforator provides assistance to the builders in some cases, with strong monolithic structures, he, as practice has shown, does not cope. Especially for such work, pneumatic boochard is usually used, which is capable of working with a large load and with large surface areas.

230mm Angle Grinder Start Up Guide

The distinctive features of such a tool are that it works for air pressure, which creates a compressor. This work can only be compared with the operation of a jack of a chipping hammer, although in the case of a boomcling with a pneumatic tool, you can use a compressor of smaller capacities. Over, if you use an electric tool in the work, we will subject it to large loads, as a result of which overheating and failure can occur.

This will not happen with a pneumatic tool, on the principle of operation, air through the hoses enters the tool, where the shock force is created. It is also worth considering that such equipment has a fairly decent weight, usually it reaches 6 kilograms, this is another of the features of the industrial model. In this case, it is precisely the weight of the tool itself that is involved in pressure on the processed surface.

Typically, pneumatic boucharda is already sold with a finished set of nozzles for work, it is a set of nozzles with longitudinal cutting plates, as well as a set with nozzles on which pyramidal teeth are installed. It is worth noting that such a tool is practically eternal, due to the minimum use of components in the unit device, it practically does not break.

Buchard for a perforator. Design and views

Not only to simplify the work, but also to accelerate their conduct, manufacturers produce not only manual boucars. To accelerate and simplify work, manufacturers produce boots for a perforator. This is a type of nozzle for a perforator, which allows you to expand the functionality of the tool. Why the nozzle was made for a perforator? Since it is this electrical tool that has a jack of chipping hammer.

Buchard’s nozzle for a perforator constructively consists of two parts. Working and fasteners. The working part has a similar design with a manual tool, and the fastener is presented in the form of a shank for fixing in a perforator cartridge. Manufacturers produce nozzles for perforators with two shanks. SDS Plus and SDS Max.

A distinctive feature of nozzles-butuchards for a perforator with SDS Max and SDS Plus Salaries is an equal number of cone-shaped protrusions, which are 16 teeth. These 16 teeth are located in a row 4 by 4. Bucharda size for a perforator with a number of teeth 16 pieces is 48×48 mm. There are nozzles for a perforator with a smaller and large number of teeth, however, the most popular are precisely 16-green devices. The nozzles with 9 teeth provide more rough surface treatment, and with 25 links allow you to give the surface of the light roughness. Varieties of nozzles Buchard for a perforator are presented in the photo below.

Like any type of tool, nozzles have an appropriate operational resource, which is equal to the processing of a section of 1000 m2. After working out such a resource, the quality of work worsens due. The teeth are not subject to sharpening, therefore, when the resource declared by the manufacturer is developed, the nozzle should be replaced.

It is interesting!Nozzles for the driving punch are whole.Lit with sDS tailings or detachable (collapsible). The second option will cost cheaper, and its main advantage in the possibility of replacing nozzles with a different number of teeth. It is possible to work with a bucharda on a perforator on concrete or granite exclusively in shock mode. A jackhammer. If you enable the rotation mode, this will lead to the Rapid wear of the teeth, as well as the injury to the operator. How much does a boucard cost to a perforator. Masters ask this question, choosing between a nozzle and a manual tool. The nozzle costs from 1000-1500 rubles, which depends on the manufacturer, quality and number of teeth. In addition, SDS Max’s nozzles are more expensive than SDS Plus. Manual bouchard costs about the same that it depends on the type of handle. Wooden or metal.

How to choose a boochard?

For domestic use, it is best to choose nozzles for a perforator or grinder.

Almost every master has these tools, which means that a full.Fledged boucard for the home will be relatively cheap, and at the same time completely functional.

Sculptors who bring their works to the ideal manually should acquire a set of manual tools.

For professional activities in the construction sector, it is better to choose, depending on working conditions, an electrical or pneumatic version, which has a great shock and work speed.

You also need to have various nozzles for performing various kinds.

Buchard for a perforator. Design and views

Not only to simplify the work, but also to accelerate their conduct, manufacturers produce not only manual boucars. To accelerate and simplify work, manufacturers produce boots for a perforator. This is a type of nozzle for a perforator, which allows you to expand the functionality of the tool. Why the nozzle was made for a perforator? Since it is this electrical tool that has a jack of chipping hammer.

Buchard’s nozzle for a perforator constructively consists of two parts. Working and fasteners. The working part has a similar design with a manual tool, and the fastener is presented in the form of a shank for fixing in a perforator cartridge. Manufacturers produce nozzles for perforators with two shanks. SDS Plus and SDS Max.

A distinctive feature of nozzles-butuchards for a perforator with SDS Max and SDS Plus Salaries is an equal number of cone-shaped protrusions, which are 16 teeth. These 16 teeth are located in a row 4 by 4. Bucharda size for a perforator with a number of teeth 16 pieces is 48×48 mm. There are nozzles for a perforator with a smaller and large number of teeth, however, the most popular are precisely 16-green devices. The nozzles with 9 teeth provide more rough surface treatment, and with 25 links allow you to give the surface of the light roughness. Varieties of nozzles Buchard for a perforator are presented in the photo below.

Like any type of tool, nozzles have an appropriate operational resource, which is equal to the processing of a section of 1000 m2. After working out such a resource, the quality of work worsens due. The teeth are not subject to sharpening, therefore, when the resource declared by the manufacturer is developed, the nozzle should be replaced.

It is interesting!Nozzles for the driving punch are whole.Lit with sDS tailings or detachable (collapsible). The second option will cost cheaper, and its main advantage in the possibility of replacing nozzles with a different number of teeth. It is possible to work with a bucharda on a perforator on concrete or granite exclusively in shock mode. A jackhammer. If you enable the rotation mode, this will lead to the Rapid wear of the teeth, as well as the injury to the operator. How much does a boucard cost to a perforator. Masters ask this question, choosing between a nozzle and a manual tool. The nozzle costs from 1000-1500 rubles, which depends on the manufacturer, quality and number of teeth. In addition, SDS Max’s nozzles are more expensive than SDS Plus. Manual bouchard costs about the same that it depends on the type of handle. Wooden or metal.

How to choose a boochard?

For domestic use, it is best to choose nozzles for a perforator or grinder.

Almost every master has these tools, which means that a full.Fledged boucard for the home will be relatively cheap, and at the same time completely functional.

Sculptors who bring their works to the ideal manually should acquire a set of manual tools.

For professional activities in the construction sector, it is better to choose, depending on working conditions, an electrical or pneumatic version, which has a great shock and work speed.

You also need to have various nozzles for performing various kinds.