Coil for the lawn mower what to choose. Classification according to the method of refueling

Trimmer coils. species and features

The efficiency and performance of the household trimmer for grass on the site largely depends on the quality of the fishing line. It is located in a coil, or, as it is also called, a trimmer head. Manufacturers produce coils of different types. Each of them is distinguished by its constructive features and the individual principle of action. Having studied them in detail, the gardener will be easier to choose exactly the head that is suitable for specific operating conditions.

The device of household motorcycles begins with its working body, the role of which is most often played by a coil for a trimmer for grass.

There are 3 types of heads on the market that differ from each other by serving cutting fishing line:

• Automatic coils. in the nozzles of this type, the cord is supplied with an increase in the speed of the engine engine motor. At the same time, the operator himself does not accept the lengthening of the fishing line. this happens in fully automatic mode. Automatic heads are the most convenient in operation and are most often used by gardeners caring for large areas. Among the disadvantages of these nozzles, experienced users distinguish frequent breakdowns of the device and the highest cost among all types of trimmer coils;
• Semi.automatic heads. nozzles of this type work according to a fairly simple principle: to serve the cutting fishing line, the coil should rest on the surface of the earth. With the simultaneous press on a special button, a built.in anchor mechanism is driven. as a result, centrifugal forces arise, under which the fishing line for a trimmer lengthens and the operator can continue to work on the site. For the operation of these nozzles, a certain dexterity is required from the operator;
• manual coils. in the design of these heads, the cutting cord is lengthened by mechanically. Accordingly, to serve the fishing line, the operator must drown the motor motorcycles and pull the fishing line for a trimmer manually. Despite the inconvenience of operation, it is this type of coils that is recognized as the most reliable and popular among gardeners.

In addition to the listed types of mowing heads on sale, universal nozzles are found. They can be installed on any model of a household trimmer for grass, regardless of its factory configuration and purpose. The universal head is highlighted in high reliability and does not require frequent repair.

Types of heads by fishing line dressing

In addition to the difference in the feed algorithm, trimmer coils are divided by each other according to the method of refueling the cutting fishing line.

There are such types of nozzles on the market:

• “Fast”. these coils do not require removal from a trimmer for grass. To refuel the cutting cord into the head, the operator needs to stretch its end into a special hole in the side of the nozzle, and wrap the fishing line for a trimmer around the central axis of the head several times. At the end, the opposite end of the cord will need to be cut and continued to mow the grass;
• collapsible. to refuel a fishing line for a trimmer, the user needs to remove the coil from a trimmer for the grass and disassemble it. After that, it is necessary to wind the cutting cord, collect the nozzle and install it back on the motorcycle.

Often on the market you can find semi.automatic coils, in the factory device of which there are a housing, a pair of built.in parts and a spool. The built-in parts are equipped with springs, and the spills themselves can be one- or two-section. In single.sectioned rogues, a fishing line for a trimmer on each side is wound evenly. In two.section, each of the ends of the cutting cord is wound from the corresponding side. This type of nozzle is considered the most practical and convenient to operate, since the cutting fishing line for a trimmer inside them is never confused.

The design of a single.sectioned spool involves the possibility of its independent refinement. To redo it into two.section, the user will need a strong metal plate, on which he needs to measure the diameter of the existing spool and cut the blank along the applied contour. To get the thickness, you need to make measurements of the place for which the cutting cord is wound. In this case, it is necessary to make sure that nothing prevents the rotation of the circle. After this, you need to make a small incision and put it on the spool. For fastening the ring, it is better to choose the glue “moment” or a special adhesive tape. As a result, the manufacturer gets a homemade two.section head for a trimmer for grass. which can be installed on different modos models.

TOP-5 best models

The following rating includes the most popular coils in five different categories. The list was compiled based on sales indicators for the current 2021 and consumer reviews for these models.

The most affordable model

Among the best available spool stands out Patriot DL-1200. This semi.automatic collapsible coil from Patriot is suitable for benzos with straight rods. Threading parameters: M10 × 1.25 LH (left metric thread, diameter. 10 mm, step 1.25 mm). Fishing thickness. up to 3 mm. Compatibility with other devices: forester, Home Garden, Elg, Huter.

The best automatic coil

The best coil of the automatic group is Denzel 96308. It is suitable for gasoline and electrical equipment with a mount for the nut M8 × 1.25 RH (diameter 8 mm, right thread). The maximum cross section of the fishing line is 1.6 mm, the length is up to 15 m. The cord is automatically lengthened when the mower is turned on.

The best semi.automatic model

In this category, the Spool is the lead Stihl Autocut C 5-2, which is designed for trimmers FSE 60/71/81, FS 38/45/50 of the same brand. It is designed for a fishing line for a trimmer 2 mm thick and is characterized by a light refueling without disassembling the head.

The best manual model

Among the handicraft coils, a larger number of positive reviews were collected by Shpul Strog-226, aluminum. This is a spider type reel with the number of cutting ends. 8. It is suitable for electric and motorcycle, does not rust and does not deform even in the most difficult working conditions. To replace the cord, ignition/power of the device must be turned off.

The best universal model

Of the many universal spool, Denzel 96316 is particularly popular. This is a semi.automatic coil for a fishing line for a trimmer up to 3 mm long. The diameter and step of the thread (left). M10 × 1.25, but thanks to the adapters, this coil can be placed on trimmers for grass with nuts and screws with a diameter of 8, 10 and 12 mm. This spool is suitable for many models of motor and electric.

So, the exit of the trimmer head is out of order is an unpleasant, but easily eliminated obstacle on the way to a neat area or a prepared sen. Even if the desired model is not in the store, you can always make the coil with your own hands, although with the current variety of goods for the garden you have to resort to this method very rarely.

Types of semi.automatic heads

Semiautomatic.type mowing head. As a rule, it consists of a case, inside which several springs and a spool are located. Shpuli, in their execution, are divided into:

Many owners of household trimmers remake single.sectioned spills for two.section. To do this, you need to find a solid metal plate, and apply a circuit with a bursal diameter on it. After that, the plate is cut along the contour so that the thickness is located near the cord winding area. As a result, the resulting circle must move freely around its axis. Further on the resulting ring you will need to make a cut and put the spool inside the ring. Both parts must be interconnected using a tape or fast.drying glue. As a result, the manufacturer gets a spool, a fishing line for a trimmer in which can be wrapped in two sections.

Classification of coils for a trimmer for grass

Since trimmers for grass are produced in a wide variety, the spills on them also have several types. They are classified according to various signs: if the user is necessary in the process of serving the string, according to the material of manufacture, by design (for semi.automatic models) and by the method of winding the cord per coil.

For feeding the cord

By the method of serving fishing line, trimmer heads are divided into:

A manual coil appeared before other options. Its design is simple and reliable, but you need to unwind the fishing line for the trimmer to replace the used. To do this, you have to change the trimmer motor for the grass and stretch both ends to the suitable length.

The semi.automatic coil allows you to lengthen the cord without turning off the engine, right during operation. To do this, you need to press the head to the solid surface so that the mechanism that releases the ends of the forest works. The centrifugal force unwinds the cord, and the person again raises the head of the device above the ground, when the length is sufficient. The whole procedure takes a matter of seconds.

The automatic coil works when the braid lowers the engine speed (the gas mower has such an opportunity, but not an ethletric trimmer for grass) or starts it. The fishing line for the trimmer is advanced until the user again increases the moment.

Important! Some cutting heads are available only for specific models of trimmers, but there are coils that are suitable for instruments of different brands and types. Such devices are called universal.

According to the material

According to the material from which the working heads are produced, plastic and metal coils are distinguished. For the manufacture of the former, shockproof plastic is used, for the latter. aluminum and steel.

By design

Spilles of semi-automatic coils are one- or two-section. On a single.section cord is wound evenly, the turns are distributed along one groove. Two.sectional bobbins are divided in half, so that the fishing line for a trimmer is laid in two grooves, and when lengthening the working part, each end is fraught out of its compartment. For such a spool, the uniformity of the turns is not important.

By type of winding

By the method of winding fishing line on the bobbin, there are the following types of coils:

To refuel a collapsible bobbin, you will have to turn off the trimmer for the grass, remove the cutting head, get the coil from it, remove the remnants of the worn fishing line and manually wrap up a new one. Then collect everything in the reverse sequence and continue the mowing.

A quick.shot reel is not required to remove the cord for wrapping. It is enough to draw the ends of the new forest in the holes on the reel body, wind it on the bobbin in the right amount and cut off the excess length or cut the loop.

Attention! It is necessary to wind up the cord when refueling only in the direction that is opposite to the working movement of the coil. The desired side is most often indicated on the rogue itself with an arrow.

Coil with automatic winding of fishing line for a trimmer for grass

How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction

Warranty production of the factory refueling of a trimmer for the grass will be in demand for fishing line substitutions. Having a very approximate idea of ​​how to tuck a fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate the myth of the process.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. certain acts will depend on the difficulty of configuration and the type of product itself:

• Small electronic trimmers for grass with a working location of the motor and coils in the bottom, usually have side buttons on both sides of the bobbin. With the simultaneous press there, the highest part of the coil, coupled with the internal contents for winding the fishing line, is disconnected, although the lower one remains on the trimmer. The analysis of the bobbin is better to create in an even smooth place, so that the spring entering the design does not jump out of it;
• Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, you have coils with a special lamb: in similar structures, you should hold a spool in a motionless position with one hand, and turn the fixing bobbin on the stalk a barack nut. After disconnecting the nut, the whole bobin is removed.
• Electronic and gasoline trimmers for grass with the ability to install a knife on a straight rod (nettles, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and with unhurried rotation, such mutual placement is achieved when the screwdriver enters the holes and the bobin is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third options of coil, depending on the design, are versed in different methods. In the bobbins with a lamb, lamb is twisted, in the reels with the latches, the fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then they are quite turned with their hands in the back sides until they are completely developed.

Coil with automatic winding of fishing line for a trimmer for grass

How to refuel a fishing line for a trimmer to a trimmer coil for grass? Video instruction

Warranty production of the factory refueling of a trimmer for the grass will be in demand for fishing line substitutions. Having a very approximate idea of ​​how to tuck a fishing line for a trimmer to the coil of a trimmer for grass without the help of others, the new ones without hunting take up this matter. But with some abilities, the development of this simple science does not represent any difficulties, and the similar annotation presented below will greatly facilitate the myth of the process.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. certain acts will depend on the difficulty of configuration and the type of product itself:

• Small electronic trimmers for grass with a working location of the motor and coils in the bottom, usually have side buttons on both sides of the bobbin. With the simultaneous press there, the highest part of the coil, coupled with the internal contents for winding the fishing line, is disconnected, although the lower one remains on the trimmer. The analysis of the bobbin is better to create in an even smooth place, so that the spring entering the design does not jump out of it;
• Electronic and gasoline trimmers for grass with a curved rod without the ability to install a knife, you have coils with a special lamb: in similar structures, you should hold a spool in a motionless position with one hand, and turn the fixing bobbin on the stalk a barack nut. After disconnecting the nut, the whole bobin is removed.
• Electronic and gasoline trimmers for grass with the ability to install a knife on a straight rod (nettles, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and with unhurried rotation, such mutual placement is achieved when the screwdriver enters the holes and the bobin is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third options of coil, depending on the design, are versed in different methods. In the bobbins with a lamb, lamb is twisted, in the reels with the latches, the fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then they are quite turned with their hands in the back sides until they are completely developed.

Criterias of choice

Before buying a spray, you should contact the documentation for a trimmer for grass, which indicates the recommended parameters of the mowing heads, the thickness of the fishing line, the diameter of the landing hole for the coil, type of mount, thread (left or right) and a fixation axis (stiff or rotating at 90/180/ 360 degrees). The same information is indicated on the packaging of consumables along with models of technology, on which you can install a specific head.

• Of the three types of coils by the method of serving fishing line, it is better to choose semi.automatic. They are more convenient. Among these spools are quick.charged models, as well as universal samples designed for different trimmers and with holes for a fishing line for a trimmer of various thicknesses. With this head, you can mow two or three types of grass: soft lawn, wild and tall, with hard stems. For each type of thicket, you will need to buy only a cord of a suitable section, and not a separate coil.
• If only vegetation of a certain type is to mow, you can stop on a coil under a fishing line for a trimmer of one diameter. Knives or discs will cope with other tasks.
• Too cheap cutting of brittle plastic heads quickly break, so excessive savings can turn into new expenses.
• You should not install the coils of little.known brands for trimmers for grass from eminent manufacturers. Popular companies are produced by components that are best for equipment of the same brand.

Often market leaders produce coils for trimmers of other companies. In this case, the replacement will work no worse than the original. For example, the Denzel 96304 working head is suitable for gasoline and electrimmers of the same brand, but is also recommended for use on mower mowers Greenline and MTD.

On a note! Some coils are designed to work only with trimmers of one manufacturer, although the lineup can be quite wide. So, the T25 head for the Husqvarna 128R gasoline apparatus is suitable for three dozens of travo.shirt models of the same company.

Among the best manufacturers, it is worth highlighting German companies Al-ko, Bosch, Stihl, Gardena, Swedish Husqvarna, American Black Decker, Patriot, Japanese Ryobi, Makita, Champion, Denzel, Huter, Hooper, Ukrainian Foresta.

Appointment and device

Trimmer coil (spool) holds a fishing line for a trimmer for mowing grass. On some devices, the cord is wound with turns, ready.made segments are attached to others. In the first case, the length of the fishing line is 1-8 m, and in some models up to 15 m, in the second-several tens of centimeters for each fragment. The coil itself is the central part of the trimmer’s working head for grass, but these terms are often used as synonyms.

A spool with a fishing line wound on it is enclosed in a case, which includes two parts: the base and cover that are connected using latches. The cord is threaded through the holes in the case, which can be 2 or more, for example, to use a fishing line for a trimmer of different diameters without replacing the coil. There is a spring between the bobbin and the lid, thanks to which the fishing line for the trimmer comes out or stretches out to replace the wore end. The design is screwed to the trimmer bar for grass with a bolt.

Criterias of choice

Before buying a spray, you should contact the documentation for a trimmer for grass, which indicates the recommended parameters of the mowing heads, the thickness of the fishing line, the diameter of the landing hole for the coil, type of mount, thread (left or right) and a fixation axis (stiff or rotating at 90/180/ 360 degrees). The same information is indicated on the packaging of consumables along with models of technology, on which you can install a specific head.

• Of the three types of coils by the method of serving fishing line, it is better to choose semi.automatic. They are more convenient. Among these spools are quick.charged models, as well as universal samples designed for different trimmers and with holes for a fishing line for a trimmer of various thicknesses. With this head, you can mow two or three types of grass: soft lawn, wild and tall, with hard stems. For each type of thicket, you will need to buy only a cord of a suitable section, and not a separate coil.
• If only vegetation of a certain type is to mow, you can stop on a coil under a fishing line for a trimmer of one diameter. Knives or discs will cope with other tasks.
• Too cheap cutting of brittle plastic heads quickly break, so excessive savings can turn into new expenses.
• You should not install the coils of little.known brands for trimmers for grass from eminent manufacturers. Popular companies are produced by components that are best for equipment of the same brand.

Often market leaders produce coils for trimmers of other companies. In this case, the replacement will work no worse than the original. For example, the Denzel 96304 working head is suitable for gasoline and electrimmers of the same brand, but is also recommended for use on mower mowers Greenline and MTD.

Among the best manufacturers, it is worth highlighting German companies Al-ko, Bosch, Stihl, Gardena, Swedish Husqvarna, American Black Decker, Patriot, Japanese Ryobi, Makita, Champion, Denzel, Huter, Hooper, Ukrainian Foresta.

Classification of coils for a trimmer for grass

Since trimmers for grass are produced in a wide variety, the spills on them also have several types. They are classified according to various signs: if the user is necessary in the process of serving the string, according to the material of manufacture, by design (for semi.automatic models) and by the method of winding the cord per coil.

For feeding the cord

By the method of serving fishing line, trimmer heads are divided into:

A manual coil appeared before other options. Its design is simple and reliable, but you need to unwind the fishing line for the trimmer to replace the used. To do this, you have to change the trimmer motor for the grass and stretch both ends to the suitable length.

The semi.automatic coil allows you to lengthen the cord without turning off the engine, right during operation. To do this, you need to press the head to the solid surface so that the mechanism that releases the ends of the forest works. The centrifugal force unwinds the cord, and the person again raises the head of the device above the ground, when the length is sufficient. The whole procedure takes a matter of seconds.

The automatic coil works when the braid lowers the engine speed (the gas mower has such an opportunity, but not an ethletric trimmer for grass) or starts it. The fishing line for the trimmer is advanced until the user again increases the moment.

Important! Some cutting heads are available only for specific models of trimmers, but there are coils that are suitable for instruments of different brands and types. Such devices are called universal.

According to the material

According to the material from which the working heads are produced, plastic and metal coils are distinguished. For the manufacture of the former, shockproof plastic is used, for the latter. aluminum and steel.

By design

Spilles of semi-automatic coils are one- or two-section. On a single.section cord is wound evenly, the turns are distributed along one groove. Two.sectional bobbins are divided in half, so that the fishing line for a trimmer is laid in two grooves, and when lengthening the working part, each end is fraught out of its compartment. For such a spool, the uniformity of the turns is not important.

By type of winding

By the method of winding fishing line on the bobbin, there are the following types of coils:

To refuel a collapsible bobbin, you will have to turn off the trimmer for the grass, remove the cutting head, get the coil from it, remove the remnants of the worn fishing line and manually wrap up a new one. Then collect everything in the reverse sequence and continue the mowing.

A quick.shot reel is not required to remove the cord for wrapping. It is enough to draw the ends of the new forest in the holes on the coil body, wind it on the bobbin in the right amount and cut off the excess length or cut the loop.

Attention! It is necessary to wind up the cord when refueling only in the direction that is opposite to the working movement of the coil. The desired side is most often indicated on the rogue itself with an arrow.

Criterias of choice

Before buying a spray, you should contact the documentation for a trimmer for grass, which indicates the recommended parameters of the mowing heads, the thickness of the fishing line, the diameter of the landing hole for the coil, type of mount, thread (left or right) and a fixation axis (stiff or rotating at 90/180/ 360 degrees). The same information is indicated on the packaging of consumables along with models of technology, on which you can install a specific head.

• Of the three types of coils by the method of serving fishing line, it is better to choose semi.automatic. They are more convenient. Among these spools are quick.charged models, as well as universal samples designed for different trimmers and with holes for a fishing line for a trimmer of various thicknesses. With this head, you can mow two or three types of grass: soft lawn, wild and tall, with hard stems. For each type of thicket, you will need to buy only a cord of a suitable section, and not a separate coil.
• If only vegetation of a certain type is to mow, you can stop on a coil under a fishing line for a trimmer of one diameter. Knives or discs will cope with other tasks.
• Too cheap cutting of brittle plastic heads quickly break, so excessive savings can turn into new expenses.
• You should not install the coils of little.known brands for trimmers for grass from eminent manufacturers. Popular companies are produced by components that are best for equipment of the same brand.

Often market leaders produce coils for trimmers of other companies. In this case, the replacement will work no worse than the original. For example, the Denzel 96304 working head is suitable for gasoline and electrimmers of the same brand, but is also recommended for use on mower mowers Greenline and MTD.

On a note! Some coils are designed to work only with trimmers of one manufacturer, although the lineup can be quite wide. So, the T25 head for the Husqvarna 128R gasoline apparatus is suitable for three dozens of travo.shirt models of the same company.

Among the best manufacturers, it is worth highlighting German companies Al-ko, Bosch, Stihl, Gardena, Swedish Husqvarna, American Black Decker, Patriot, Japanese Ryobi, Makita, Champion, Denzel, Huter, Hooper, Ukrainian Foresta.

Features of coils for trimmers EFCO 8100

This coil for a trimmer for the grass is universal (photo shown below) is sold with a special adapter for connecting. In this case, the wrapping system is provided by automatic type. The mounting diameter is 6.2 mm. The height of the head in the model is 76 mm. Directly a fishing line for a trimmer is used with a diameter of 1.3 mm.

The device is mounted by a screw method. The protective casing of the coil is packed from shock.resistant plastic. The cup of the presented model by the manufacturer is not provided. If you believe the reviews of buyers, then the coil is connected without problems. The model copes with fine grass very quickly. However, large weeds should be avoided. The user is capable of buying the presented coil for 1300

What are the coils

The main advantage of the trimmer for grass is maneuverability and mobility. Its purpose is grass growing in summer cottages, aligning lawn grass and mowing meadow.

Using this device, you can mow grass in those places where a gasoline lawn mower cannot get. In addition, using a trimmer for grass, you can easily process irregularities and slopes. If you replace the cutting element with a disk, then they can even cut and trim the bushes and flower beds.

The structure of the trimmer for the grass begins with the cutting part, then there is a bar, an engine and a handle with a control mechanism. To work with the lawn on a trimmer for the grass, a coil is installed (head). As a rule, three types of coils are different by the method of feeding fishing.

• Manual. The principle of operation is easy to determine by name: a fishing line for a trimmer is served mechanically. In order to lengthen the cord, you should interrupt the operation of the device and manually lengthen the ends. Despite the apparent inconvenience, this type of coils is the most reliable in work. Their use requires a certain dexterity, but, having learned to work with manual heads, in the future there will be no difficulties.

Having examined all three options for coils, you can come to the following conclusions: manual are the least preferable to use in terms of convenience. Semi.automatic, although less reliable, but provides basic comfort. Automatic is the most convenient, but when operating such a coil, users usually complain of increased fishing line consumption. Most users and experts agree that the most preferable and optimal is the semi.automatic coil.

As already mentioned above, there is also a universal coil for a trimmer for grass. A distinctive feature of this type of head is a wider area of ​​application. Simply put, they are not suitable for one model of trimmers, but for several. To make sure if a universal head is suitable for your trimmer for grass, you should study the marking of the part itself. If it coincides with the model of your trimmer for grass, then you can safely purchase this coil.

The advantage of universal coils is their relatively low price and widespread prevalence. The deficiency can be considered the declared support of the trimmer model for grass, although in fact they may be incompatible.

To exclude confusion, it is recommended to consult with the seller, calling him a model of his trimmer for grass in advance.

Before buying an consumable, you should study its features in advance. For example, many universal coils of metal, not plastic. Although they have a fishing line for a trimmer, as a rule, from the same universal material as most manufacturers.

Opinion about coils for trimmers Flymo 15

This coil for a trimmer for grass (universal) is made with an automatic wrapping system. The cup in it provides for a small thickness. Buyers complain that she wears out very quickly. However, it is important to consider the small price of the goods. The height of the installed head is 74 mm. A small dimeter is used directly for the trimmer. The core in this case is made completely of metal. Suitable head for garden trimmers of various manufacturers. You can find the indicated coil in the market for 700

The trimmer means motorcycles or electrocos. In fact, this is one of the variety of lawn mowers (manual mower), which are designed to mow grass. This is a modern braid braid. Initially, they were developed to carry out agricultural work, however, the main use of the trimmers was precisely the mowing of lawns.

For the first time, the idea to create a trimmer for grass came to the head of an American entrepreneur J. Bollas. Passing by car through an automatic car wash, he noticed that the principle of rotating brushes can be used for beveling agricultural crops.

After that, he collected a primitive trimmer for grass from a tin can (as a coil) and a fishing line flowed into the holes drilled in it. He installed the resulting design on a pole on which the engine was previously mounted from a moped. The device is a mowing not only wheat, but also grass. Realizing that on the sale of braids for the grass he will earn a lot of money, the entrepreneur improved his product and gave him the name “Destroyer of weeds”. A feature of the invention was the possibility of a bevel of grass around the trees. the forest perfectly cut the grass, but did not injure the bark.

The main purpose of such a tool was the bevel of grass in small areas in places where classic wheel technology cannot be used:

• in the presence of a large number of shrubs;
• in gardens with a large number of trees;
• near fences and fences;
• If the site has an uneven relief.

All trimmers for grass have a bar. the main constructive element. A gasoline or electric engine is attached to the rod from one end, and a coil with a fishing line is put on the other. the main working element. over, the type of transmission can be any. it is limited only by the capabilities of the manufacturer and commercial parameters.

Features of coils for trimmers Flymo 22

This coil for an electric trimmer for grass (universal) is made with a reliable wrapping mechanism. The mounting diameter in this case is 6.5 mm. The height of the installed head is 72 mm. A model for trimmers “Hyundai” and “Makita” is suitable. If you believe customers, then the head is unwound very quickly. The model copes with the one.year.old grass without problems.

According to the owners, the casing of the coil uses high.quality. In this case, the cup practically does not wear out. However, when working, it is important to beware of large weeds. The user is capable of purchasing this model for 1200