DIY Nazadka for a lawn mower. We get acquainted with the types of nozzles on Motokos

Homemade attachment for a trimmer for grass for weeding potatoes

People are increasingly trying to move away from manual cultivation of potatoes. This brings a lot of health problems, takes time. Landing, irrigation, as well as weeding, are increasingly becoming mechanized.

Do I need potatoes? Several facts:

Many people think that they will grow up, once they planted. But with all the variety of weed grass, it is not able to fully develop. In the early stages of growth and the formation of the bush, it is very important that the garden is clean, otherwise harmful vegetation will ruin the potatoes and will not allow the vegetable to gain momentum in full force.
Another fact why weeding is to carry out is stretching of nutrients from the soil. Rhizome, creeping, with abundant green mass of grass will absorb humus much faster than culture develops.
Weeds are a haven for the fruitful development of some insect pests, which in the fall lay their eggs on it, and in the spring are born and begin to earnly eat young potatoes.
With rapid growth, weeds will stand up with a “carpet”, then the potatoes will not receive in full light and air.

Usually weeding the garden is carried out several times a season, and until the moment when the bushes are getting stronger, rise, then they themselves will be able to inhibit weeds growing under them.

Reviews

Nadezhda, 52 years old: We have a large garden for planting potatoes. Therefore, you have to use mechanisms during the weeding. Otherwise, just can’t cope with such a area of landings. For weeding, we use one.axle tractor. He greatly simplifies the work.

Sergey, 42 years old: we have a small area for planting a small. Therefore, there is no need to use a one.axle tractor or a trimmer for grass. We are fully cope with ordinary pulls. This is convenient, you can immediately hill the bushes.

I was weeding when growing potatoes is a mandatory event. It eliminates weeds, allowing plants to receive the right amount of sunlight and air at the initial stage. With a large area of the site, it is better to use mechanized processing methods. If the area of the landings is small, the potatoes are torn by ordinary pulls.

Advantages and disadvantages of the nozzle-cultivator

The prefix-cultivator for a trimmer for grass is becoming more and more popular among customers. Here are some advantages of this device:

Simplicity in maintenance.
Noticeably cheaper in comparison with equipment for a motorbike.
Such a cultivator is simply indispensable for those people who have many greenhouses. Using this device, you can quickly loosen the ground in the greenhouse and saturate it with oxygen.
The design is made very high quality, which makes it possible to use the cultivator for a long time.
Protective shield. Protects from the garbage of the operator.
Each nozzle weights the structure, with prolonged work, a person will feel fatigue.
You need to select a nozzle and a trimmer for grass with the same connecting nodes.
Due to vibration, control the button of the trimmer switching for grass and holding a difficult unit is often uncomfortable.

Important! The model of the cultivator nozzle should be produced by the same company as the trimmer for the grass. If the loosening tool is produced by Husqvarna, and the lawn mower is Oleo-Mac, then it will not work to process the soil: the nozzle simply cannot be attached

Features of work by nozzle

Any nozzle-cultivator for a trimmer for grass significantly increases the weight of the entire device assembly (at least 5 6 kg). Therefore, long.term work with such a tool is not possible for everyone. The calculation must also include mechanical restrictions on the power of the trimmer drive for grass. If the engine is designed for a power of not more than 1,500 watts, then the cultivator can only be processed by regularly loosened soil, or limit yourself to hovering breasts, potato bushes, etc. P.

Since the drive of gasoline trimmers is located behind the worker, and the drive bar is quite long, vibrations constantly occur in the process of cultivation. Their value is determined by both the length of the bar and the change in the load on the wheels or cutters. These vibrations through the shoulder belt are transmitted to the user’s hands, so it is not always convenient to control the trimmer button to turn on the trimmer for grass and hold the canopy. Therefore, prolonged cultivation of soil using a cultivator nozzle is unsafe for health.

But not everything is so bad: the mobility of a gasoline trimmer for grass allows you to easily process the soil in the rowles, and the absence of wheels on a hinged cultivator does not damage plants on the beds.

Cultivator nozzle “does not like” creamy soil, and at the first introduction into such soil, the bar abruptly discards. Therefore, disk cultivators are equipped with a safety casing (gear mills are more likely to bend than break, although in this case a low protective shield from the legs would not have prevented). The presence of a safety screen worsens the visibility of a working with a cultivator.

How to properly weed potatoes with a trimmer

The implementation of the rules for the correct weeding of potatoes with a trimmer will avoid mistakes and work quickly, easy:

It is better to weed potatoes in a respirator and goggles, since when rotating milling dust, weed vegetation particles take off up.
Processing using a trimmer for grass is carried out at least once in 14 days, since it is yet lended on for weeds that have not yet been rooted.
The best time for weeding is an early sunny morning.
Simultaneously with the elimination of weeds, the loosening of potatoes is carried out if the cutting elements are deepened by more than 1.5 cm.
The smaller the engine power, the more often you should arrange a break, giving it a rest.
Before work, cutters are treated with silicone lubricant, and on heavy soil such weeding is not carried out.
Trimmer nozzles for grass must be periodically treated with a disinfectant that will destroy the pathogens of the disease.
During work, other people should not be nearby.

Important! A clash of the nozzle with a solid object. a stone or a metal element. will lead to a breakdown of motorcycle

The principle and effectiveness of the weeding method

Weeding as a cultivator processing aims to destroy the weed by weed by exhausting. plants after processing need time in order to recover and gain the desired force. At this time, potatoes or other vegetable crops will be able to continue successful growth.

The weeding of potatoes with a trimmer is usually carried out by three methods:

sparing weed grass with a mowing head or disk nozzle;
cultivator processing with a drum nozzle;
Cultivator processing with saber or disk nozzles.

Speasing is usually carried out when weeds reach a height of 7-10 cm. In this case, only the part that is above the ground is mowed, and the roots remain in an untouched state. Usually after this begins rapid growth of green mass, so that the effectiveness of such processing is small.

How to build a HOMEMADE LAWN SPRAYER. 5 nozzle boom

When the weeding with a trimmer is carried out using a drum cutter, the roots of weeds are also processed. A big plus of this method is that the upper soil layer is scared, and thus increases the air exchange of soil. The effectiveness of this method is much higher than a simple weeding manually or work by a mechanical cultivator. The drum mill allows you to loosen the soil to a depth of 3-5 cm.

When using saber or disk nozzles, effectiveness increases even more-the processing depth increases to 5-7 cm. At the same time, the roots of plants, like the green mass of weeds, are repeatedly grinded, which contributes to the rapid decomposition of plant residues in the ground. After such a weeding, repeated weeding is usually carried out after at least 10-14 days. True, there is one nuance that needs to be taken into account. when working with drum mills, the width of the processed strip is about 30 cm., But when working with saber or disk mills, the width is no more than 15-20 cm.

Varieties of cultivators

Tornado

Tornado is the simplest version of the cultivator, which can be made with your own hands. Outwardly it looks like a corkscrew, which is fixed on a vertical tripod. The design is equipped with a horizontal handle on top. For its manufacture, use simple pitchfork and nozzle for the cuttings. You can buy a nozzle at a hardware store. It has the shape of a handle and is used to work with forks and shovels.

In the cultivator, the handle should be long. Therefore, the nozzle must be increased. For lengthening, use a plastic pipe, slightly larger diameter than the thickness of the plastic nozzle. The length of the pipe should be about 0.5 m. So that the pipe can be put on the handle of the handle, it is carefully cut along and twisted.
The pipe is chopped with island. Fixed, during operation it will not slide, and jump from its place. The finished handle on both sides will turn out protrusions about 25 cm long.
Using a simple hammer, the teeth of the foriles are changed under the shape of a corkscrew. Stronging strong blows to metal teeth, they will begin to bend in the necessary direction. Original photo of the cultivator, help to repeat its exact bends.

Cultivator from a bicycle

The design of this manual cultivator is more complicated. It is made from parts of the bicycle: frames and wheels.

A do.it.yourself cultivator head from sharp metal rods is fixed on a bicycle frame. As a head, you can take a part from the old cultivator. From a small plow create a frame of the device.
From a metal or aluminum pipe with a diameter of 2 to 2.5 cm, the handle is built.
All compounds are rigidly fixed by bolts. Structural elements should not hang out.
A medium.sized wheel is fixed on the frame. As fasteners, barashika nuts or simple counter-hacks are used as fasteners. The wheels are too large or small do not fit here.

The cultivator is designed to remove weeds. It processes a row.

Disk rotary equipment

The disk rotary cultivator is designed for harrowing, and alignment of the surface of the earth. They are good to break large soil pieces. Assembly of technology:

Convex spherical disks installed in the cultivator is the main working tool. It is very difficult to make discs yourself. Metal plates with a thickness of 44 mm from a simple form, you need to make a spherical. Stronging strong beats with a hammer in the center of the plate, they knock out the bowl. Convex discs are obtained. Ready elements are welded to the axis dressed on the axis.
The axis is inserted into the brackets and fixed with chlobs.
A special ledge is located in a large bracket. A pipe with handles passes through it.
Rod, 24 mm in diameter, 25 cm long to a small bracket.
A 16 mm thick rod is screwed into the rod. A small part of the rod will protrude above the crossbar.

The angle of disk installation can be adjusted using a barashka nut, which is installed on the crossbar. Turning the nut, the rod will rise up and the big bracket bend, changing the direction of the disks.

Cultivator from a meat grinder

In addition to the manufacture of manual devices, you can assemble an electric model yourself. The design of the cultivator assembled from a meat grinder is very simple.

For the manufacture of handles, two corners are screwed to the gearbox, and two pipes are welded to them.
For convenience, the ends of the pipes are bent, and a suitable segment of the pipe is welded between them, which will create an additional strength to the handles.
Wheel axis is welded to the corners. The size of the wheels choose the average.
The nozzle from a meat grinder is beaten with a sledgehammer until the sleeve becomes cast.iron.
The shaft is pulled out of simple scrap and set it in the nozzle. A screw-zaucard screw is also welded here.
To make a cultivator conveniently turn on and off, the engine switch is installed on the handle.

If you need to do neatly loosening the earth, the cultivator is slowly moved. Grury plowing is obtained with the rapid movement of equipment, while the earth is soldered by large Комментарии и мнения владельцев.

From a chainsaw

The basis of the design is the engine from the chainsaw. Additional details that you need to buy: a metal corner, a tube and fuel tank, wheels, a moped star and a star with 41 teeth.

From the metal corners we make a frame size 32 × 32 cm. The shape of the frame should resemble a cube. The engine is installed on the transverse corners, and the fuel tank below the brackets. Intermediate shaft. mount on vertical corner racks. Bearings are attached to the longitudinal corners. They are designed for the running shaft. The same.based tractor with the center of gravity on the wheel is ready.
Handles are made from a pipe with a diameter of about 30 mm.

Stars for the intermediate and running shaft, as well as the rest of the parts are collected in a single mechanism. The garden cultivator is ready.

How to make a manual cultivator for processing a row

To process narrow places between the rows, first of all, the cultivator must be compact. For such work, a manual device called “hedgehog” is well suited. Having all the necessary details, it is easy to make it yourself. For the assembly of the “hedgehog” you will need: the bracket of the P-forms with holes, shaft, stalk and wheels with metal spikes.

So that the one.axic tractor easily moves around the site, you need good wheels. To do this, take a medium.sized steel pancakes and weld metal spikes to them. The spikes are easy to make, you need to sharpen the fittings in the shape of a cone.
Ready cutters put on the axis.
The axis is inserted into the bracket and fixed on both sides.
The mount is welded to the end of the bracket and the stalk is inserted.

The technique is collected and ready for cultivation and weeding between rows.

From a trimmer for grass

A made cultivator from a trimmer for grass with your own hands will help to quickly and easily and easily and easily. You can assemble it from improvised materials: a working gasoline trimmer for grass, corner grinding or welding, garden forks, steel tubes.

For the manufacture of cutters, the teeth from the foriles are bent in the desired shape. Usually the soil is loosened to a depth of 10 to 15 cm, so the length of the teeth should be no more than 15 cm.
Next, we make the working part. The teeth of the foriles are flattened to the width of about 1 cm.
The mills are pulled with emery and fixed on a round heel.
A nickel with a diameter of 10 cm should be perfectly flat in shape. Mills in the amount of three pieces are located evenly on the heel. If you put more than three pieces, then the device will be strongly overloaded.
The final part is a connection of the base with cutters and a trimmer for grass. Well, if the shaft tip has a thread. Then the trimmer for the grass is simply screwed to her.

The technique is designed for loosening the soil at a small depth.

Homemade cultivator from a trimmer for grass: what is needed, the stages of the process

The cultivator facilitates the treatment of soil, reducing the expenses of time. This nozzle useful in agriculture with rotating cutters allows you to loosen the ground and destroy weeds. With its help, it is possible to quickly process the soil, without affecting the fertile layer.

A cultivator is a universal garden tool that perfectly replaces a shovel and a plug. Mechanized equipment allows you to quickly spill and dig small soil areas. Cultivated land in the beds, flower beds and greenhouses gets rid of weeds and becomes soft. This simple device is planted on a tractor or one.axle tractor.

The factory device is quite expensive, so many prefer to make it with their own hands. For the base you can take an ordinary gasoline trimmer for grass. As an alternative, it is permissible to use an electric motorcycle.

What is necessary for the manufacture of a cultivator based on a trimmer for grass

To create an agricultural unit, a certain set of tools will be required. It is also necessary to choose the components of the future device for processing the soil. A set of tools and materials for turning a trimmer for grass into a cultivator includes the following items:

Garden pitchfork.
Corner grinding machine for metal cutting. Should have a set of discs with a diameter of 125 mm.
Welding apparatus and electrodes.
Drill with a set.
Electric jigsaw.
An sandpaper. Two abrasive circles are installed on it.
A metal sheet. Preferred thickness. about 5 mm, suitable dimensions. 1010 cm.
A set of manual tools: wrench, hammer, pliers, marker, roulette.
Steel long tube, the diameter of which is suitable for shaft.

Collecting a mini-cultivator with your own hands is not so difficult. Using this technical device, you can process small soil areas at a small depth.

The optimal power of the trimmer for grass is 2 horsepower.

We will make three mills for the future device. We use teeth from garden forks for this. This is the working part of the future device that weed.

For the cultivator, you will need three rods. You can use a larger amount of milling, but in this case an increased load on the motorcycle is created. The length of the rods should be from 10 to 15 cm. This is the depth on which soil loosening is produced.

Now it remains to combine two parts. We attach a working element with cutters to a finished basis, that is, to an electric or gasoline trimmer.

Reverse thread at the end of the shaft will facilitate the task. In this case, light fastening of the milling. Before work, you should weld a pipe with a nut to them.

Cultivator is a useful device for agriculture. It allows you to loosen the soil without turning large layers of the Earth. If you have experience in locksmithing, you can quickly make a simple garden cultivator from a gasoline trimmer for grass. The alteration does not require special financial costs. The electric motorcycle is worth supplying with an extension cord, which will increase the processed area.

Nazadka-cultivator for a trimmer for grass: nuances when working and mounting methods

What is the device?

In a set of interchangeable nozzles, Motokos, manufacturers have recently been increasingly mentioning such a device as a cultivator or proof.

Unlike classic nozzles in the form of discs for mowing grass or mowing head for a synthetic fishing line for a trimmer, the cultivator is designed to work directly with the soil.

A trimmer nozzle for grass is designed to loosen the soil in the processed areas and partially in places where there is a turf cover.

A trimmer nozzle for grass was weeding potatoes

How to make a lawn grass trimmer from drill machine. Easy diy.

A trimmer nozzle for weeding is put on a bar instead of a lower gearbox. Converting a trimmer for grass into a prosperger is carried out within 1-2 minutes and does not require additional tools and equipment. The entire process is carried out using hexagonal keys included in the tool of the tool motorcycle.

The use of motorcycles greatly facilitates the weeding

Rivets for rivets: types, dimensions, application

The case of the device collapsible. The housing has special devices for adding lubrication. Corps material. aluminum alloy, cutters are made of steel. Shaft on which milling cutters, forged, gear bronze.

The principle of operation of the trimmer for the grass is simple. from a two.stroke engine through the clutch, rotational movement is transmitted to the shaft in the bar. Further, through the shaft, the movement enters the connecting shaft with a worm mechanism, from which a working shaft with mills begins to rotate through a bronze gear.

The speed revolutions are adjusted by adjusting the number of engine speeds through the gas handle. the more the carburetor shutter opens, the higher the rotation speed of the milling.

From corner grinders

Most often, a home.made electric trimmer for grass is made on the basis of a conventional corner grinding grinder, which is available to every home master. This tool is almost perfect for remaking into a trimmer for grass.

It has a larger power than store machines and more than a minute.

In addition, the standard nut used in the corner grinding for fixing the disks already has holes through which it is easy to insert a fishing line for a trimmer (cord).

So, there are many options from which to make a bar (holding). The simplest is the longer a wooden holder than for a shovel. To the end of it, an angular grinder is attached at the right angle with a conventional tape. The fishing line for the trimmer is inserted into 2 holes of the nut, after which it is twisted. Thus, in a few minutes you get a trimmer for grass, which can be mowed without problems.

For the safety of the operation of a home.made apparatus, you can improve it by making a protective casing (how to do this, will be considered later).

For advanced masters with a welding machine, you can advise a more advanced design to fix the angular grinder and protective casing. It is made from an aluminum tube (serves as a holder) and a metal square profile. Looking at the picture below, you can understand the principle of manufacturing the holder.

The corner grinder is fixed on the holder with bolts inserted into the holes that are designed to attach the handle to the device.

The following photo shows how this design looks below.

How to make a pipe bastard with your own hands: examples of the best self.use

Next, the “native” casing of the corner grinder is removed, and instead of the disk, either a fishing line for a trimmer or a metal disk knife is installed.

By the way, you can fasten the holes for fastening the handle (bar) itself, when you want to make a simple trimmer for grass, which is easily assembled and is also easily versed if you need to use the corner grinding for its intended purpose.

To make it more convenient to hold a trimmer for grass in his hands during work, and it did not rotate around the axis of the bar, you can attach a side hand made of a bent pipe to it.

The principle and effectiveness of the weeding method

The weeding of potatoes with a trimmer is usually carried out by three methods:

sparing weed grass with a mowing head or disk nozzle;
cultivator processing with a drum nozzle;
Cultivator processing with saber or disk nozzles.

When the weeding with a trimmer is carried out using a drum cutter, the roots of weeds are also processed.

A big plus of this method is that the upper soil layer is scared, and thus increases the air exchange of soil.

The effectiveness of this method is much higher than a simple weeding manually or work by a mechanical cultivator. The drum mill allows you to loosen the soil to a depth of 3-5 cm.

When using saber or disk nozzles, effectiveness increases even more-the processing depth increases to 5-7 cm. At the same time, the roots of plants, like the green mass of weeds, are repeatedly grinded, which contributes to the rapid decomposition of plant residues in the ground.

After such a weeding, repeated weeding is usually carried out after at least 10-14 days. True, there is one nuance that needs to be taken into account. when working with drum mills, the width of the processed strip is about 30 cm.

, But when working with saber or disk mills, the width is no more than 15-20 cm.

Pros and cons of the method

Weeding a trimmer of the garden, and even more so the site on which the potato grows has its own characteristics and specifics. First of all, you need to pay attention that for work you need to choose the right tool.

It is preferable to choose powerful four.stroke engines as a working engine. Such motorcycles have a lower gasoline consumption and greater performance compared to two.stroke.

Nazadka-cultivator for a trimmer for grass. Is it worth buying?. The tool is a master

What nozzles for a trimmer for grass are considered in this review (nozzles for lawn mowers and electric cosmos are the same)

Nozzle drill for a gasoline trimmer for grass (works without electricity).
Nozzle of running wheels to work conveniently work with a brush.
Suchkoreza nozzle working on the principle of hacksaw.
Nozzle garden scissors for haircuts of hedge and bushes.

This is, in addition to the trimmer head for caring for a personal plot and a bed, various metal and plastic knives for the mowing of natural and seeded herbs and weeds, as well as a sawn disk for cutting young trees, bushes and branches with a trimmer.

The nozzles for a trimmer for grass (also nozzles for lawn mowers) are attached to a trimmer in one of three ways:

The engine of the trimmer for grass can operate in any position and has a high specific power (power relative to the mass), it is also compact and reliable, which allows you to use it with any mounting equipment that is presented below. Let’s look at the nozzles for the grass in more detail. Nozzles for the lawn mower the same.

Nazadka for a trimmer for grass drill

Drill nozzle is a nozzle for a gasoline trimmer for grass, t.e. Electricity is not necessary for the operation of such a drill.

In addition, such a gasoline drill is characterized by high power, reliability and durability (compared to an electric drill).

Huge torque at the drill provides a lowering gearbox with a gear ratio of 17: 1. 3-sized cartridges are available. With a trimmer echo technical characteristics:

Nazadka for a trimmer for grass running wheels

It is used with air vents or other nozzles if necessary.

It is especially convenient to use running wheels for a trimmer for grass along with a sweeping brush or roller. you can raise the working body and, accordingly, reduce friction about the surface (it is easier to work, less wear, better result and pleasure from work). Cm. also: Raiffeisen Bank Aval in Kremenchug.

Trimmer nozzle for tender

The nozzle nozzle is designed to cut knots and branches at a height of up to 4.5 m. The appointment is also that the nozzle has altitude, but if the altitude works according to the principle of the chainsaw, then we work as a brushwood on the principle of a hacksaw.

Garden scissors

Garden scissors nozzle is designed to haircut hedges and curly bushes (nozzle for the lawn mower is the same). two modifications with different lengths of the bar for different situations.

Nazadka for a trimmer for grass aerator lawn

The nozzle is designed for aeration, t.e. saturation of the upper soil with air by piercing it (this is especially true for lawns over 5 years with a thickened root system), as well as for the destruction of the crust on the surface of the soil of the lawn after rain, watering or trampling to restore the breathability of the soil. Processing width. 20 cm.

Nazadka for a trimmer for grass cultivator

The cultivator nozzle is designed for loosening the soil on flower beds, flower beds, in greenhouses, small beds, around trees and bushes.

Diameter cutter. 20 cm.
Tree of cutters. 180 rpm.
Processing width-12-24 cm (depending on the power of the engine of the trimmer for grass).
Weight. 5 kg.

The disadvantage of such a cultivator (in the form of a nozzle for a lawn mower) is its low weight. it processes the upper layer well, especially in a freshly sprinkled place, but on hard ground it scratches at the top, and does not climb into the soil.

The cultivator’s nozzle for a trimmer for grass does not allow the milling cutters to the ground. the rod is spring, which causes strong wear of the guide shaft of the plastic sleeve and a strong pressure can lead to the bend of the bar and breakdown of braids for grass or nozzle cultivator.

Highway grass trimmer

The high.rise nozzle is designed for drilling branches and bushes up to 15 cm thick and thinning the crown of trees at an altitude of 4.5 m from the ground.

It is a gearbox in a case with an oil tank with a connecting hole on a trimmer for grass and a chain tire. Tire length. 21 cm.

When choosing a nozzle of altitude, it is necessary to check whether the size and shape of the teeth on the slotted part of the drive shaft coincide in the nozzle and on the trimmer.

Nazadka for a trimmer for grass gearbox

A gear nozzle can be used as a motor for a bicycle, moped, picture, ATV, snowmobile, etc.D. The gearbox drops 5 times. You can change the direction of rotation of the output shaft. You can also change the leading star. put a sprocket with any number of teeth, thereby select the required gear ratio. The nozzles for the lawn mower are identical.

Nazadka for a trimmer for grass water pump

Water pump nozzle allows you to serve water from the river, lakes, containers, well, etc.D. for watering the beds, car washing, household water supply, watering water into the tank of the summer shower, filling the inflatable pool, pumping water from the cellar, etc.D.

Brushell and roller shaft nozzles for a trimmer

The same nozzles for the lawn mower. the rotating rubber brush of high performance sweeps the garbage without damaging the surface.

These nozzles for a trimmer for grass are designed to sweep garden paths and platforms from fallen leaves, cleaning of mowed grass from the surface of the lawn, removing moss. Especially effective with running wheels for trimmer for grass.

Can be made as a brush (as in the photo), or maybe like a rubber roller (as in the video). Capture width. 60 cm.

Nazadka for a trimmer for grass support wheel

A new support wheel for a trimmer for grass can significantly facilitate the work of a trimmer with various nozzles. This nozzle can be fixed on a trimmer for grass in various positions, which ensures its versatility and adaptability.

The supporting wheel allows you to maintain the same height of the lawn haircut, as well as the same depth and width of processing during the operation of the edge of the flower beds and garden paths. The nozzle is equipped with two support wheels for the operation of the edge or one rotary wheel to work a trimmer.

DIY Cultivator Propeling Cultivator

Why buy a cultivator, and, moreover, to weed the beds with a grip, if for these purposes you can adapt a gasoline motorcycle. In this case, you will not have to hump with a grinder all day, remembering everything on which the light holds.

There is nothing complicated in the manufacture of a cultivator pro-cultivator. True, you will need a welding machine and the ability to cook metal. If there is no skills in welding, then, welcome to the website Mmasvarka.ru, there everything is described in detail in order.

Preparation of materials for remaking motorcycles to the cultivator

Alteration of motorcycles, it is said loudly. Remake this tool useful for the summer resident, you will have very little. All that is required is to remove the head of the trimmer for the grass and its plastic casing to protect. Everything else, a home-made nozzle-cultivator will be, with which you can easily loosen the beds in the garden.

So, from the materials for the manufacture of nozzles on a motorcycle, you need to get:

The very manufacture of the nozzle on the motorcycle is nowhere easier. Below will be presented step.by.step manufacture of this device.

How to make a pro-cultivator from a motorcycle

First of all, it will be necessary to cut a plate from a piece of metal, about 15-20 cm long, and 5-7 cm wide. The plate should be made of fairly thick metal, with a thickness of at least 3 mm. The load on the plate with bolts during the opening of the beds will be large enough, so it is better not to save with the thickness of the metal for the manufacture of this homemade.

After the plate is cut out, a hole under the shaft of motorcycles is drilled strictly in the center. It is very important to drill a hole precisely in the center of the plate, because, otherwise, there will be a strong vibration and beat of the nozzle during operation. The diameter of the hole should be slightly larger than the puck that is installed on the shaft of the trimmer for the grass.

Then, using welding, it will be necessary to weld the nuts at the edges of the plate (at the same distance from the edge and also in the center).

The nuts will be needed in order to tighten long bolts in them, which, in turn, will act as spikes of a cultivator nozzle on a motorcycle.

In principle, if there was no welding inverter at hand, then you can fasten the bolts to the plate through through holes, there is nothing complicated in this.

On this, a home-made nozzle-cultivator for a lawn mower is almost ready, it remains only to make a piece of thick or metal from a piece of thick or metal-a protective casing.

To do this, first you need to cut a circle of metal, which will be a little larger than the plate with bolts in diameter, and then weld it to it in a circle, a metal strip, 7-10 cm wide.

To fasten protection for motorcycles, you need to use a home.made clamp.

Now it remains only to conduct tests, after the cultivator nozzle is screwed to the shaft of Motokos. And, as practice shows, this device has quite effectively showed itself when weaped not too hard land. With the help of it, you can quickly get rid of vegetation in the garden, and also easily loosen the beds.

Today you can buy ready.made options for proofs.

The following articles:

Comfortable stand for corner grinder with your own hands
Cope.cheap device for drilling pits for pillars
Interesting design of homemade loops on the door or gate

Features of work by nozzle

Design and fastening options

Cultivator nozzle is in two versions:

Disk, whose cutting organs are a pair of cutting discs;
A gear, which is a number of milling on the shaft.

The fundamental difference is only in the design of the loose knot. Disk nozzles are more stringent, and therefore suitable for processing heavier soils, while the toothed ones have less their own weight, but are designed for work on lighter soil.

The transmission of the rotating moment from the engine of the trimmer for the grass for the hacker-cultivator is carried out using a special shaft, which is arranged in a special rod (it will have to be purchased separately). This node is not interchangeable, and differs in the number of slots on the end part of the bar: there may be seven or nine. Therefore, conceiving the acquisition of a cultivator nozzle, it must be understood that the OLEO-MAC factory is not suitable for a trimmer from Husqvarna, as if vice versa.

The slotted method of joining disks or cutting to the shaft allows the free movement of the cutting organs, which is ideal for cultivation, since it allows you to loosen the soil with a fairly wide capture (up to 200 250 mm per pass), without requiring a large amplitude of the rod movement. Restrictions on the density of the beds located on the site are also removed. With lengthening the beds of convenience of working with the nozzle under consideration, the turns will have to be done much less often.

Is it worth it to make a cultivator nozzle yourself?

The price factor has a noticeable effect on the choice: whether to purchase such a nozzle, or make it yourself. High-quality nozzles-cultivators for a trimmer for grass can be purchased at a price of 11,000 20,000, which justifies itself only with large volumes of work. It is inappropriate to buy such a node in cases where the processed soil is heavy (for example, chernozem or loam): the cultivator does not lift the soil, but only moves the lands from one place to another, moreover, along with the roots of torn weeds or grass.

The technology of vegetation care will also change: at first, a nozzle-knife should go along the beds, cutting off the grass, and only then use the cultivator nozzle.

Having made a decision on the independent manufacture of a cultivator nozzle to a trimmer, the following should first evaluate:

The design of the output section of the bar: if it is a flexible shaft, then you will have to forget about the cultivator: it will not withstand the amplitude of rotating moments. The cardan gear is more functional, and the most successful design is considered a multi.and.line rod, and a straight line, and not curved.
Drive power: if it is less than 1000 watts, then the engine will overheat, and cultivation performance will decrease sharply.
The volume of the fuel tank: energy consumption will increase significantly, since the cultivator nozzle will have to be made from improvised materials. Therefore, the tank should contain at least 1 liter of fuel.
The execution of the handle. Ergonomics experts believe that the most convenient is the T-shaped handle, which provides the most accurate and reliable direction. It is difficult to hold a gasoline trimmer for grass with a cultivator nozzle common in some models with a J-shaped handle.

If the existing trimmer for the grass satisfies the listed requirements, and its owner has sufficient experience in performing such work, then it is quite possible to make a disk nozzle with his own hands. As for the nozzles of the gear type, their independent manufacture is very time.consuming, and will not provide the desired quality.

Types and principle of work of cultivators

The principle of operation of the cultivator is simple: the element that loosen the ground begins to work after the mechanical part of the device is launched. Depending on the external size, engine power and performance, cultivators are divided into three types: light, medium and heavy equipment.

Light equipment is used in small areas with soft soil (flower beds, greenhouses).
Medium severity is used on clay soils.
Heavy equipment refers to universal equipment. It can be used for any soil.

Cultivators are of different types: disk, rotational, lap and milling. In terms of functioning, they can be: manual, with electric drive and working on gasoline, as well as trailed, hinged, process one or more rows. When processing a land plot, everyone chooses the model you need. Hand cultivators are good in that they can be made independently with minimal cash costs.

Advantages and disadvantages

Each cultivator, regardless of whether it is manual or electric, has its pros and cons of.

Manual cultivator. Easy to use and much more conveniently shovels, compact. Does not load the lower back. The soil loosens well, does not melt the roots throughout the site. But this technique will not cope with the unlucky land, as it has low performance. It is better to use it in small areas, such as flower beds or greenhouses.
Electric cultivator. Light and compact equipment working from the network. Simple in maintenance. The lack of equipment is an electric cord. It can interfere during operation, and due to its length there is a limitation in the processed area. Has low power and small soil processing depth. Not intended for hinged equipment.
Gasoline cultivator. Thanks to hinging equipment, it has many functions. Does not connect to electricity, so it can move throughout the site. Suitable for processing small territories. Weighs much more electrical equipment. It is difficult to care for it, and fuel is required for refueling.

How to make a manual cultivator for processing a row

So that the one.axic tractor easily moves around the site, you need good wheels. To do this, take a medium.sized steel pancakes and weld metal spikes to them. The spikes are easy to make, you need to sharpen the fittings in the shape of a cone.
Ready cutters put on the axis.
The axis is inserted into the bracket and fixed on both sides.
The mount is welded to the end of the bracket and the stalk is inserted.

The technique is collected and ready for cultivation and weeding between rows.

From a trimmer for grass

For the manufacture of cutters, the teeth from the foriles are bent in the desired shape. Usually the soil is loosened to a depth of 10 to 15 cm, so the length of the teeth should be no more than 15 cm.
Next, we make the working part. The teeth of the foriles are flattened to the width of about 1 cm.
The mills are pulled with emery and fixed on a round heel.
A nickel with a diameter of 10 cm should be perfectly flat in shape. Mills in the amount of three pieces are located evenly on the heel. If you put more than three pieces, then the device will be strongly overloaded.
The final part is a connection of the base with cutters and a trimmer for grass. Well, if the shaft tip has a thread. Then the trimmer for the grass is simply screwed to her.

The technique is designed for loosening the soil at a small depth.

How to make a snowman with your own hands from a trimmer for grass

Under the expression of a snowplower machine from a trimmer for grass with your own hands is meant the manufacture of a snow.resistant nozzle. It is fixed to the bar motorcosa instead of a working head. Twisting is transmitted through the native gearbox. The nozzle is a small round case with wheels, inside which a knife rotates on the bearings. The working element can be assembled with your own hands in the shape of a screw or impeller with blades. The second option is simpler, and the first is more productive. A pipe segment with a diameter of 300 mm, an old gas cylinder or a beer barrel is suitable for the case.

A step by step is collected by a snow.pipe from a trimmer for grass with your own hands in the following order:

Having decided on the type of snowman (rotary or screw), draw with their own hands or find a drawing on the Internet. According to the scheme from steel tubes, corners and plates, a frame is welded, on which all the elements of the snowpipe will be mounted.
If it is decided to follow the simplest path, having converted the motorcycle to the rotary snowman, they begin to make a body from a barrel or a gas cylinder. The pipe for this design is disadvantageous due to the absence of the bottom. Will have to additionally weld the plug. It is better to give preference to a beer barrel, as it will not rust from contact with moisture. From the capacity of the corner grinder, a piece of 150 mm long is cut off from the bottom of the bottom.
The center is precisely determined on the bottom of the resulting workpiece. Drill a hole on the mark. Its size is 2-3 mm larger than the diameter of the shaft of the trimmer gearbox for grass. Small holes are drilled around the main. Their diameter, quantity and location depends on the model of the motorcosa gearbox. Usually on the housing 3 holes. To make an accurate coincidence, the gearbox is applied to the bottom and mark the marking.
To throw snow from the snowpipe body you need a deflector. It is placed on the side of the workpiece. Having thought out where the upper body will be, a hole with a diameter of 100 mm is cut in the side shelf. You can cut down the window with your own hands using a square.shaped chisel, but the process of making a pipe will become more complicated. It’s easier to cut a round hole with welding. The deflector pipe is welded from a piece of pipe 100 mm long.
A semicircle is cut out of leaf steel with their own hands. The fragment in size should close 1/3 of the end of the body. The element is welded in the upper part from the deflector side.

All the details of the snowman are ready. It remains to assemble them in one structure, install on a trimmer for the grass. First of all, the motorcosa gearbox is screwed with bolts to the end of the case. The shaft should rotate freely without hooking. The body is fixed with bolts to the frame. Depending on the chosen mechanism of the movement of the snowman, the wheels or skis are installed. The impeller is put on the shaft of the gearbox. Try to scroll with their hands, convinced of the free course. Launch the motor motorcycles. Try to walk in the snow in the snow. The control handle is a trimmer bar for grass. If everything is correctly collected, during the movement of the snowman from the removal knee, snow will fly.

Sources:

https://kursi-floristiki.ru/yagody/prisposoblenie-dlya-trimmera-svoimi-rukami.html
https://titan-spec.ru/instrumenty-i-stanki/kultivator-iz-trimmera.html
https://gorodminvody.ru/nasadka-na-trimmer-dla-propolki/
https://rustaste.ru/nasadka-kultivator-dlya-benzokosy-svoimi-rukami.html
https://nzmetallspb.ru/stanki/nasadka-kultivator-dlya-benzokosy-svoimi-rukami.html
https://nzmetallspb.ru/tehnologii/nasadka-kultivator-na-motokosu-svoimi-rukami.html
https://stroimpilim.ru/%D0%B1%D0%B5%D0%B7-%D1%80%D1%83%D0%B1%D1%80%D0%B8%D0%BA%D0%B8/nasadka-na-trimmer-dla-propolki-kartofela.html
https://titan-spec.ru/instrumenty-i-stanki/nasadka-na-trimmer.html
https://smontage.ru/oborudovanie/kultivator-iz-benzokosy-svoimi-rukami.html

Lawn Mowers lawn, motokos, mower, nazadka, nozzles, types