How to Clean a Lawn Mower Carburetor Without Removing It (Yes, It’s Possible)…

How to Clean a Lawn Mower Carburetor Without Removing It (Yes, It’s Possible)

Removing the carburetor 20-thread bolt using an M10 wrench sounds more like an engineering project than a quick lawn mower repair for a Saturday morning. Carburetors are fairly complex mower parts that annoyingly need attention if you want to keep your lawn mower running smoothly. So, do you have to know a lot about engines and have a tool collection to clean a carburetor? And do you have to remove the carburetor to clean it? Let’s take a look.

Can You Clean a Lawn Mower Carb Without Removing It? (The Short Explanation)

If you’re suffering symptoms of a bad carburetor, you’ve probably come across a lot of people who recommend removing the carburetor to clean it. Even though I say this myself, it’s not the only solution. A carburetor doesn’t need to be stripped down and squeaky clean to work well. So, do you need to remove the carburetor to clean it? No.

There are two methods to cleaning a carburetor while it stays on the lawn mower. The first is a chemical spray clean, and the second is a jet removal clean. So let’s go over how to clean a carburetor without removing it.

Chemical Spray Cleaning

• Remove the Air Filter Cover
• Remove the Air Filter
• Spray the Outside of the Carburetor with Carburetor Cleaner
• Brush the Outside of the Carburetor with Small Nylon Brush to Remove Dirt Grime
• Start the Engine
• Set Engine to Fast Idle
• Spray Cleaner into Carburetor
• Run the Engine for Several Minutes to Burn Off Cleaner
• Replace Air Filter
• Replace Air Filter Cover
• Switch Off the Lawn Mower

Jet Removal Cleaning

• Switch Off the Fuel
• Remove the Fuel Cup Bolt
• Remove the Fuel Cup
• Remove the Jet Retaining Screw
• Remove the Jet
• Clean the Jet
• Replace the Jet
• Replace the Retaining Screw
• Replace the Fuel Cup
• Replace the Fuel Cup Bolt
• Switch On the Fuel

How to Clean a Lawn Mower Carburetor Without Removing It? (Step By Step)

Now that you have seen how to clean a lawn mower carburetor without removing it let’s take a more detailed look at the steps you’ll need to follow.

Step By Step Carburetor Chemical Spray Cleaning

The first step is to remove the cover from the air filter to gain access to the inside of the carburetor. You may find that your cover is secured with a screw, so you’ll need to grab a screwdriver to remove the fastener.

Next, remove the air filter from within the filter housing and set it to one side. If your lawn mower has two filters, you’ll need to remove both of them, including the air filter and pre-filter.

Now, grab your carburetor cleaner and give the outside of the carburetor a good spray. Try to get the cleaner into all the nooks and crannies so that it really gets to work on all the dirt.

Next, use a small nylon brush and start working off all the dirt and grime. I like to use an old toothbrush for this part of the cleaning. Also, don’t be tempted to use any type of metal brush as the carburetor is made of a soft alloy that is pretty delicate. A toothbrush should work just fine.

Once you are happy with the outside of the carb, you can go ahead and start the lawn mower’s engine and set the throttle to a fast idle.

With the engine running, use the same cleaner and give the inside of the carburetor a good spray. A couple of seconds should be enough. Just make sure that you don’t stall the engine. Once the engine has burned off all the cleaner, give the carburetor another spray inside. I like to repeat this a couple of times to make sure it’s getting a good thorough clean.

Next, allow the lawn mower to run for a few minutes after you believe the engine has burned off all the cleaner. This allows any of the cleaner sticking around to burn off completely.

The last job is to reinstall the air filter and replace the air filter cover. If you had to remove a screw for the cover, remember to screw it back in. Also, this is the perfect time to inspect the air filter and make sure it’s not soaking in oil or worn out. You could even clean the air filter before putting them back in.

Finally, switch off the lawn mower or head out and tackle your lawn.

Tools Parts to Spray Clean Your Carburetor

Step By Step Carburetor Jet Cleaning

The first job is to switch off the lawn mower’s fuel if you have a cut-off valve. This will save any unnecessary fuel spillage.

So, start by removing the bolt on the bottom of the carburetor located at the center of the fuel cup. You’ll need a small wrench for this. Now, for some of you guys, this bolt is the actual jet. This means you can skip the next steps until we get to the cleaning part. For you guys that don’t have this type of carburetor, keep following along.

Next, once you have removed the bolt, you should be able to pull the fuel cup off the carburetor. Just be a bit careful, as the cup will probably be full of gasoline.

Now, located where the fuel cup bolt would connect to the inside of the carburetor, you’ll find a screw. Take a screwdriver and remove this retaining screw. Once you take this screw out, the jet should fall out. Some lawn mowers incorporate the jet into the screw, so just take a close look.

Next, it’s cleaning time. So, if you take a look at the jet, you should see a clear hole all the way through it. I find holding it up to the light helps. What you are going to need to do is remove any dirt that is clogging the hole. I find that a thin wire works well enough. Once you have it cleaned out, you can give it a spray of your carb cleaner and wipe off any grime.

Finally, it’s time to put the few bits back on the mower. So the order is the jet, screw, fuel cup, and finally, the bolt. For you guys with just the bolt/jet, pop it back into the mower and tighten it up with your small wrench.

That’s all there is to it. It’s pretty straightforward and takes no time at all. Just don’t forget to turn the fuel back on.

Tools Parts for Carburetor Jet Cleaning

Cleaning a Mower’s Carb: To Remove or To Not Remove

So, we have discussed how to clean a lawn mower carburetor without removing it, but will this solve all your carburetor issues? Well, it depends. You’re going to find that spraying the cleaner directly into the carburetor is going to cure problems from fuel impurities, fuel gum, and bad fuel in your mower. However, a clog in the carburetor jet needs a bit more work, like my jet cleaning method. Also, you’re going to find that some lawn mowers don’t offer enough room to remove the carburetor jet. This means the carb is going to have to come off.

So, if you have a lawn mower like a Yard Machine with a Briggs Statton engine, you’ll probably have to remove the carb, but give the chemical spray a try first.

About Tom Greene

I’ve always had a keen interest in lawn care as long as I can remember. Friends used to call me the “lawn mower guru” (hence the site name), but I’m anything but. I just enjoy cutting my lawn and spending time outdoors. I also love the well-deserved doughnuts and coffee afterward!

Leave a Reply Cancel reply

Copyright © 2010. 2022 LawnMowerGuru.com, All Rights Reserved.

Affiliate disclosure: As an Amazon Associate, we may earn commissions from qualifying purchases from Amazon.com. You can learn more about this here.

How to Clean a Lawn Mower Carburetor Without Removing It?

To clean a lawn mower carburetor without removing it, start by disconnecting the spark plug.

Then, remove the air filter and spray some carburetor cleaner into the throat of the carburetor.

Starving for FUEL: The Battle Against a Stubborn Riding Mower That Refuses to Start! Briggs/Nikki

Next, use a screwdriver to adjust any idle screws located near the throttle linkage or governor arm until you hear an audible click.

Finally, replace all parts and reconnect the spark plug before restarting your lawn mower engine.

Make sure to read and follow all instructions on your specific product’s label for safety precautions prior to beginning this process.

These steps should help ensure that your lawn mower is running efficiently and safely!

• Prepare the area: Place the lawn mower on a flat, level surface and disconnect the spark plug wire from its terminal to prevent accidental starting of the engine
• Make sure that all fuel valves are closed and that no fuel is present in the carburetor bowl
• Turn off the Lawn Mower: The first step to cleaning a lawn mower carburetor without removing it is to turn off the mower and let it cool down completely.
• Remove Air Filter: The air filter is usually located on the side of the carburetor. Remove the air filter from the carburetor and clean it with a brush or replace it if it is too dirty.
• Disconnect the Fuel Line: Locate the fuel line that connects the carburetor to the fuel tank and disconnect it. Make sure to have a container ready to catch any fuel that may come out.
• Spray Carburetor Cleaner: Use a carburetor cleaner spray and spray it directly into the carburetor while moving the throttle back and forth. This will help loosen and dissolve any dirt or debris that may have accumulated inside the carburetor.
• Use a Brush: After spraying the carburetor cleaner, use a brush to scrub the inside of the carburetor, paying attention to the small crevices and jets.
• Reconnect the Fuel Line: Once you have cleaned the carburetor, reconnect the fuel line to the carburetor and ensure that it is tightly secured.
• Start the Lawn Mower: Finally, start the lawn mower and let it run for a few minutes to ensure that it is running smoothly.
• Spray Carb Cleaner: Use an aerosol-based carb cleaner spray to remove dirt, dust, and other debris from around the exterior of your lawnmower’s carburetor
• Be sure to cover all exposed surfaces with a light misting of cleaner before wiping them down with a clean cloth or rag
• Remove built up deposits: Once you have sprayed down all external surfaces with your chosen cleaning product, use a small brush or toothpick to scrape away any stubborn deposits from within crevices on the body of your lawnmower’s carburetor. Take care not to damage any delicate components during this step
• Apply lubricant: After completing these steps it is important to apply lubricant onto moving parts such as bearings and shafts located inside your mower’s carburetor assembly in order to ensure smooth running operation for years to come

How Do You Unclog a Carburetor Without Removing It?

If your carburetor is clogged, you may be able to unclog it without removing it. The first step is to remove the air box or filter so that you have access to the engine and carburetor.

You can then use a vacuum cleaner with an attachment specifically designed for cleaning out a carburetor.

Use this tool to suck out any dirt or debris that has built up in the small passageways of the carburetor.

If there is no visible dirt or debris, spray some aerosol parts cleaner into each opening on the side of the carburetor and allow it time to loosen any stubborn deposits before vacuuming them away.

Once you are satisfied that all obstructions have been removed, reattach the air box/filter and start your engine – if no smoke billows from underneath your hood then congratulations! You’ve successfully unclogged your car’s Carburetor without having to take it off!

Can You Spray Carb Cleaner Directly into Carb Lawn Mower?

The answer to whether it is safe to spray carb cleaner directly into a carb lawn mower depends largely on the type of carburetor used.

If the engine has an adjustable main jet, then spraying carb cleaner directly into it can cause damage due to over-filling or incorrect adjustment of the jet.

For this reason, if your engine has an adjustable main jet, you should not use a direct application of carburetor cleaner as a cleaning method.

On the other hand, if your lawn mower uses a sealed-type or non-adjustable main jet (commonly found in older models), then you can safely use one with caution and care.

When using any chemical product like this, always wear protective eyewear and gloves and work in a well-ventilated area away from open flames or sparks since many products contain flammable solvents that could be ignited by either source.

Additionally, when using any kind of fuel additive such as a fuel stabilizer or octane booster along with these cleaners take great care to ensure they are compatible before adding them together in order to avoid potential harm caused by mixing incompatible ingredients inside your engine’s fuel system.

What’S the Easiest Way to Clean a Carburetor on a Lawn Mower?

Cleaning a carburetor on a lawn mower is not as difficult as it may seem. The most straightforward way to do this is to first remove the air filter and then unscrew the screws that hold the cover of the carburetor in place.

Next, use a clean rag or brush to carefully remove any dirt or debris from inside the housing.

Once all of this has been removed, you can then spray some parts cleaner onto a cloth and wipe down all of the surfaces inside of your carburetor.

Afterward, make sure that everything is dry before reassembling your lawn mower’s components in reverse order – replacing both the air filter and cover before reconnecting it back into place. Doing so should leave your mower running better than ever!

Can You Clean a Briggs And Stratton Carburetor Without Removing It?

Yes, it is possible to clean a Briggs and Stratton carburetor without removing it.

The best way to do this is to first take off the air filter cover and then spray out any dirt or debris that has built up inside the carburetor with a can of compressed air.

You can also use an old toothbrush or cotton swab dipped in carburetor cleaner to gently scrub away any stubborn buildup.

Once you have cleaned the outside of the carburetor, you should inspect it for any debris and deposits that may be blocking fuel passages or jets.

If these are present, they should be gently removed using a small pick or screwdriver before being flushed out with more compressed air.

Finally, reassemble your Briggs and Stratton engine as per manufacturer’s instructions for proper operation.

How to Clean a Carburetor Without Removing It

Cleaning a carburetor without removing it is possible, but not always easy. To do so you’ll need a good quality carburetor cleaner and some shop towels.

You should start by spraying the cleaner into all of the ports in your carburetor while holding it at an angle to make sure that any debris or dirt can escape out of the bottom.

Once done, use shop towels to wipe off excess cleaner and then let the carburetor air dry for 10 minutes before replacing it in its original position.

Conclusion

In conclusion, cleaning a lawn mower carburetor without removing it can be an effective way to keep your engine running optimally.

With the right tools, supplies and instructions, you can safely and effectively clean the carburetor on your lawn mower.

This method is also cost-effective as it eliminates the need for expensive repair costs or new parts.

Plus, you’ll have peace of mind knowing that this simple DIY technique helped extend the life of your machine.

How to Clean a Lawn Mower Carburetor

It’s 9:00 AM on a beautiful Saturday morning this summer. Your daughter has a soccer game at 11:00 AM and you are ready to get a little lawn mowing done before the game.

You pop open the garage door, head on over to your lawn mower, and give the pull string a swift tug to fire it up. And. nothing happens!

We feel your pain because we have been there too. There is a really good chance you need to clean your mower’s carburetor before it will ever start again.

We are going to get you familiar with carburetors and teach you how to clean them in this iGoPro Blog Post.

Introduction to Carburetors

A lawn mower is an essential tool for maintaining a beautiful lawn. Like any piece of lawn equipment, it must be properly maintained to ensure it does not fail while in use.

Battery-powered mowers are gaining popularity, but the majority of lawn mowers still run on gas engines which means they have a carburetor.

Gas engine mower’s runs by gas mixing with air and being ignited by a spark like other combustion engines. Air passes through an air filter in the carburetor and mixing with the fuel before the spark plug ignites the gas/air mix.

The purpose of a lawn mower air filter is to prevent dust and dirt from clogging up in the carburetor and engine. Most fuel lines also have a filter, in this case, a fuel filter, to keep any debris in the gas from entering and damaging the engine’s internal parts. Even if the debris in your engine doesn’t immediately cause noticeable problems, the result is energy loss and increased gas consumption.

The carburetor is one of the most essential components of a lawn mower. The carburetor ensures the proper mix-up of gasoline and air in the engine to keep the engine running properly.

The Importance of Keeping Your Mower‘s Carburetor Clean

Cleaning your carburetor ensures it will continue to work properly. If not, its ability to regulate combustion will be seriously compromised. Air should flow into the carburetor, mix with the gas, and start the engine.

Everyone knows lawn mowers cut grass. When the blades are actively engaged, the engine is put under more stress and this is when it is even more imperative that your lawn mower carburetor is clean. Over the years we have run into situations where the engine operates as expected until put under the additional stress of having the blades engaged.

Therefore, regular maintenance of the engine is necessary. First, check if your mower is working properly and clean it. As there are different models of engines, when disassembling, you should look carefully or always refer to the assembly manual and take pictures as you go.

Make sure the fuel line is shut off before removing the carburetor. Most have a knob you can turn to shut off the flow of fuel through the line to the carburetor. If yours does not, you can pinch the line to temporarily cease the flow of fuel.

After removing the carburetor, clean it thoroughly so that its floating valve can move freely. Then replace the carburetor and open the fuel line back up.

Items Needed to Clean a Carburetor

You will need a handful of items you can find at any auto parts store to clean the carburetor on your lawn mower.

Carburetor Cleaning Material List:

• Carb Cleaner
• Shop Towels
• Oil
• Screwdriver
• Ratchet Sockets
• Pressurized Air is Recommended
• Possibly a Carbuteror Repair Kit for your Specific Carburetor

Steps for Cleaning the lawnmower carburetor

Cleaning a lawn mower carburetor is something anyone that is slightly mechanically inclined can do on their own. It is important to pay attention as you disassemble the carburetor so you know how to reassemble it! Once again, we recommend you take many pictures to document the disassembly to assist with reassembly.

Here are the steps to clean your air filter carburetor:

The first step to cleaning carburetor is to remove it from the engine. Once you have done this, disassemble, clean it, and maintain it. Make sure you have shut off the flow of fuel prior to removing the carburetor.

• Prepare to Remove the Carburetor From Your Lawn Mower: Remove the spark plug by pulling on the spark plug wire to disconnect. Shut off the flow of fuel to the carburetor by turning the shut-off valve or pinching the line. Then identify the bolts or screws attaching your carburetor to your mower’s engine and remove them. Sometimes you will need to remove or loosen additional engine components to fully remove the carburetor.
• Remove the cap screws holding the carburetor from the engine and be very careful not to damage the diaphragm between them.
• Carefully remove the rubber gasket from your carburetor. If you don’t see it, it may be stuck to the engine. You don’t want carb cleaner touching your gasket as it can corrode it. If your gasket is damaged at all, it must be replaced with a new gasket before reinstalling or fuel will leak.
• Remove the bowl, metal bulb from the bottom of the carburetor using your tools. Clean it with an aerosol cleaner and a clean shop towel.
• Remove the 0 ring that sticks to the bottom of the bowl. Check for cracks or wear, replace, and set aside.
• Get a carb cleaner, or carburetor cleaner, then inject the fluid into each port and make sure it comes out at the other end of the port. These ports are very narrow and easily clog. That is why the air filter and fuel filter are so important!
• If you are not noticing the carb cleaner successfully traveling through the ports, try using compressed air with a needle tip air gun to blast out any blockage. If that doesn’t work, try soaking the carburetor in carb cleaner and trying again hours or days later if needed.
• Reassemble any internal parts of the carburetor you may have removed in the process. Once complete you can start reattaching the carburetor to your engine.
• It is recommended to put a small amount of oil on the gasket before sealing it back to the engine when tightening the bolts that connect it.
• Turn your fuel line back on.

Pro Tips For Cleaning Carburetors

You’ve just learned about the importance of the air filter and fuel filter. They are probably the reason you needed to clean your carburetor in the first place! Why not replace these inexpensive items while you are working on your carburetor?

Do not use wire brushes or thin pieces of wire to clean a carburetor. Carburetors are calibrated to achieve the perfect air to fuel mix and must be 100% sealed. Using any type of hard material to clean a carburetor is a great way to compromise your carburetor.

Additional Lawn Mower Maintenance Tips

• Use only fresh fuel for your lawn mower. Old or stale gasoline will thicken and reduce flow to the carburetor. This is actually one of the problems that keep your mower from starting.
• Check the oil level regularly and change the oil at least once a year or per your mower manufacturer’s recommendations. Dirty oil is another great way to ruin an engine quickly.
• Make sure your lawnmower blades are kept sharp as dull blades will tear your grass instead of cutting it. Learn more about sharpening mower blades.
• Check the mower’s spark plug at least once a year. If it is dirty, you can clean it or replace it.
• Make sure your lawnmower wheels are inflated, rotating freely, and haven’t been damaged.
• After each use, clean the bottom of the mower to remove accumulated grass. If grass collects under your mower’s deck, you will notice a dramatic drop in ‘cut quality.’ The space above your mower’s blades under the deck most remain open for the blades to create lift and provide a flush cut of the turf.
• Check wires, wire connections, belts, and lines on your mower to ensure they are fully connected, not pinched, and have not been cut or melted.
• Always prepare your lawnmower correctly for winter, even if it will only be out of use for a month. To do this, siphon the fuel out of the gas tank and run the engine until it completely drains the carburetor of fuel.

By ensuring that your lawnmower is in good condition, you will be rewarded with several years of exceptional use. Follow the maintenance tips above on a regular basis to ensure that the mower always starts on the first start and mows the lawn as you would expect.

Conclusion

Proper care of your lawn mower parts will keep them in top shape, and most importantly, reliable and safe. There is nothing more frustrating than going to mow the lawn to realize your lawn mower will not start. If this happens you to, we hope this article helps and remember, there is a good chance it has something to do with your carburetor.

Ryan Sciamanna

Ryan is the owner and founder of Lawn Crack, LLC the parent company of iGoPro Lawn Supply. He has worked in almost every capacity within the lawn and landscape industry for small local companies, nationwide companies, and of course, owning his own lawn landscape business which he sold in 2018 before starting selling lawn and garden products online. Learn more about Ryan by subscribing to the LawnCrack YouTube Channel.

How to Use Lawn Mower Carburetor Cleaner

Wondering how to use lawn mower carburetor cleaner? You’re in the right place. Give your mower the care it needs to help extend its useful life. We’ll show you the steps to take in our complete guide below.

The Quick Answer

If you’re in a hurry, the following steps are the basics you need to know to use lawn mower carburetor cleaner:

• Get your lawnmower ready
• Remove its air filter
• Access the carburetor’s interior
• Spray the cleaner
• Remove extra buildup
• Put the mower back together

How to clean lawn mower carburetor in under 5 minutes!

It might seem intimidating if you’ve never done it before, but using a carburetor cleaner on your lawnmower is a relatively simple process. Keep reading for a complete walkthrough.

Using Lawn Mower Carburetor Cleaner

Let’s take a deeper dive into using lawn mower carburetor cleaner. But first, a carburetor often gets clogged over time. It’s critical that you clean it from time to time to prevent it from creating sludge which it then puts into the engine. That said, o nly a few quick steps are standing between you and a cleaner machine.

Get Your Lawn Mower Ready

When getting ready to use a carburetor cleaner, the first thing you need to do is prepare your lawnmower. It’s easy. All this it entails is ensuring the mower’s engine is off. If you operated the mower recently, you also have to wait for it to cool down. After making sure the engine is off and cool, you can safely perform the following steps.

Remove the Mower’s Air Filter

When the engine is cool, it’s time to remove the mower’s air filter. The air filter is usually toward the top of the engine and located within a plastic casing. Sometimes the case lid snaps into place, while on other models, you’ll need a screwdriver to remove it.

Dust off the area around the air filter before removing it. The air filter helps keep dust and dirt from getting into the engine. You don’t want to accidentally create more of a mess while trying to clean the carburetor.

Access the Carburetor’s Interior

With the air filter and its casing out of the way, you should be able to see the connections and links running from the carburetor to other parts of the engine. You need to disconnect and remove these connections to access the carburetor’s interior.

Make a careful note of where and how these connections were attached. You’ll have to reattach them when you finish cleaning the carburetor. If you’re not confident in your ability to remember where everything went, it can help to take a picture with your cellphone.

Spray the Cleaner

Now that you have access to the carburetor, you can clean it properly. To do so, you’re going to want to start the lawnmower engine. When the mower is operating, spray the carburetor cleaner directly into the center of the carburetor.

A high-quality commercial lawn mower carburetor cleaner works best for this step. It might seem counterintuitive, but spraying the cleaner while the engine runs allows it to penetrate deeply and remove more debris. Exercise care to avoid spraying other parts of the mower’s engine while you work.

Remove Extra Buildup

As you’ve been spraying the cleaner, dirt might fall and stick to the lower throttle of the carburetor. If you see debris, remove it. Ensure the cleaner is reaching the carburetor’s throat. With that done, you can again turn the mower off.

It should still be relatively cool because it hasn’t been running long, but exercise caution just in case. Keep spraying the carburetor to remove any extra buildup.

Put the Mower Back Together

All that remains is to put the mower back together. First, reattach and replace any connections you undid to access the carburetor’s internal parts. If you took a picture before disassembling the pieces, take a look at it now. Make sure the links are securely attached to the correct areas.

Now, you can replace the mower’s air filter. Take a moment to knock some of the dust and debris off the filter, then put it back where it was. Reattach the air filter’s casing cover by snapping it into place or putting in the necessary screw.

Things to Consider

When you follow the above steps, the result should be a clean carburetor. Other things to consider include:

• Has it been a few years since the last time you cleaned the carburetor? Typically, it’s best to clean it once every season. If it’s been a while, expect more dirt.
• Do you have the proper protective gear? Gloves will help keep you safer and clean while you work.
• Do you disconnect the spark plug? If you don’t, you’re at risk for an electric shock.

Keep these considerations in mind while you work.

Frequently Asked Questions

You might still have questions after reading about how to use lawn mower carburetor cleaner. Read further to discover answers to some of the more common inquiries.

Is the Cleaning Process Different for Riding and Push Lawn Mowers?

The carburetor cleaning process should be similar between riding and push mowers. The location of the carburetor itself will vary slightly but not considerably.

You might need assistance if you’re working on a riding lawn mower, as some models have a dead man’s switch built in to stop the engine if there isn’t enough weight in the seat.

How Can You Tell the Cleaning Helped?

If cleaning the carburetor helped, your lawnmower should start up much more smoothly than it did previously.

What if the Lawn Mower Still Isn’t Working Well After Cleaning?

Sometimes, cleaning a lawn mower’s carburetor won’t noticeably improve its performance. If you’re still having issues, it’s best to contact someone specializing in small engine repair. An expert can diagnose and solve more complex problems.

Should You Use Lawn Mower Carburetor Cleaner?

Using lawn mower carburetor cleaner isn’t difficult. With the proper precautions, you can do it safely and efficiently. Doing so is an important maintenance activity, and it will help keep your lawn mower functioning at its highest level.

If you found this guide useful, consider taking a moment to look at more of our how-to guides for homeowners.

You Might Also Like: